Comsys OND-2015 User Manual

TELEPHONE MOBY

USERS MANUAL

OND-2015

- 2 -

- 3 -

SAFETY INSTRUCTIONS

To reduce the risk of fire, electrical shock, and injury, please follow these
basic safety precautions before you use this equipment.

1. Carefully read the instructions in this manual.

2. Follow all warnin gs a nd i n structions marked on th e uni t .

3. When cleaning, unplug the telephone jack from the wall outlet. Use a
damp cloth. Do not use liquid or aerosol cl ea ner s .

4. Do not use this equipment near water e.g.: near a kitchen sink, ba thtub,
washbowl, laundry rub, swimming pool or in a wet basement.

5. Install in a protected location. Ensure all lines and cords are away from
foot traffi c. Do not place object s on the line cord that m ay cause damage or
abrasion.

6. Avoid spilling any liquid on the unit. This may cause internal shorting, fire
or shock. Otherwise, the phone is not covered under your warranty.

7. Do not overload wall outlets and extension cords as this can r esult in the
risk of fire or electrical shock.

8. Never push objects of any kind i nto this telephone as they can touch
dangerous voltage points or short out parts that could result in a risk of fire or
electrical shock.

9. Take the phone to a qua lif ied technician when it requires repair work or
service. To reduce the risk of electrical shock, do n ot disassemble the
telephone. Opening or removing c overs can expose you to dangerous
voltages or other risks. Incorrect re­assembly can cause electrical shock duri ng subsequent use.

10. Avoid using the teleph one dur ing an electrical storm. There can be a
slight risk of elec trical shock from lightning.

11. Do not use the telephone to report a gas leak, if in the vicinity of the leak.

12.Unplug this telephone from the wall outlet and refer servicing to qualified
service personnel under the following conditions:

• If liquid is spilled into the unit.

• If the unit is exposed to rain or water.

• If the unit does not oper at e nor m al ly by following the o perating

instructions.

• If the unit is dropped or the casing is damaged.

• If the unit exhibits a distinct change in performance

- 4 -

6

THE PARTS

1

2

3

4

5

1. Receiver

2. ON/OFF HOOK
button

10
9

8

11

7

7. R button

8. Keypad

9. IN USE indicator

3. REDIAL button

4. MEM. button

5. PAUSE button

6. Microphone

10. MUTE button

11. Battery
compartment

- 5 -

INSTALLATION

Connect the telephone cord to the telephone and to
the telephone jack. Check that the telephones works
by pushing the ON/OFF HOOK button and listen for
dial tone and also check that IN USE lamp is lit.

BATTERIES

In order to keep the memory (MEM and REDIAL) when
the telephone is unplugged you can install two
batteries.
Use batteries of type R03 or LR03 (AAA).
You can always make calls and answer calls without
batteries.
The battery compartment is on back side of the
telephone. Before installing the batteries, unplug the
telephone cord and unscrew the screw that is locking
the cover. Observe the polarity (+/-) that is marked in
the compartment.

OPERATION OF TELEPHONE

1. REGULAR DIALING

a. Press ON/OFF HOOK butt on, the IN USE LED wi ll
light, and get a dial tone, enter the telephone number,
the number will be dialed out.
b. Press ON/OFF HOOK button again to hang up and
the IN USE LED will turn off.

- 6 -

2. REDIAL FUNCTION

This feature allows you to redial the last number you
have called by one-touch operation.
a. Press ON/OFF HOOK button and g et a dial ing tone.
b. Press REDIAL butto n to redial the last number.

3. PAUSE FUNCTION

Allows you to insert a temporary pause during dialing
sequence. For example, dialing an international
number (eg: 011-886-22-795-1234), some telephone
company systems will not register the entire number
entry without a pause between the prefix numbers.
You may have to dial 011- PAUSE, dial 886 - PAUSE.
This allows adequate timing for the phone number to
register with the telephone company's system and
complete the call.

4. FLASH (R) FUNCTION

Press R button to terminate a call and institute a
dialing tone for another call or to get another call from
"Call Waiting" (a special telephone service).

NOTE: If you do not have any special telephone
service, such as Call Waiting, press R button during a
call may disconnect your current conversation.

- 7 -

5. MEMORY FUNCTION

To store a number in memory

1. Press ON/OFF HOOK button.

2. Enter the telephone number you want to store, then
press MEM. button.

Dialing a number from memory

1. Press ON/OFF HOOK button, then press MEM.
button to dial it out.

6. MUTE FUNCTION

If you wish to speak privately to someone else in the
room without your caller overhearing, press and hold
MUTE button. You will still be able to hear the caller's
but they can not hear you during the mute operation.
To resume normal conversation, just release MUTE
button .

WALL INSTALLATION

The unit can be mount e d to any wall surface usi n g two
self-tapping screws (not supplied). Follow the
instructions.

1. Install the two self-tapping screws at a distance
of 85mm from each other and located on a
vertical centre line. See Figure 1

- 8 -

2. Slowly slide the unit down until it snaps into
place. See Figure 2.

MOUNTING

PINS

Figure 2

SERVICE

If your telephone does not work as expected, contact
the reseller. Information and support can also be found
on the website of Ondico AB: www.ondico.se

- 9 -

DECLARATION OF

CONFORMITY

- 10 -

- 11 -

- 12 -

90053_IB_EN_080616

www.ondico.se