Plug the micro end of the USB cable into the
micro USB port at the rear of your coMra Palm,
and the other end into any powered USB port
(computer, laptop, powerbank, etc.), or a mains
electrical socket (using a suitable adaptor).
A red LED indicator next to the on/o switch
will light up and the battery will start charging.
1hr
When the battery is fully charged the red LED
indicator will switch o. A full battery charge
takes approximately 1 hour.
Page 5
x1
2
sec
x2
x1
2
sec
x2
x1
DOWNLOAD THE LATEST COMRA USER GUIDE
An app, listing over 200 treatable conditions,
can be downloaded for iOS and Android here:
www.comra-palm.com/comra-app
Alternatively, you can get a printable PDF here:
www.comra-palm.com/comra-userguide
Please read all the IMPORTANT information in
the coMra user guide, before using your coMra
Palm for the rst time.
Page 6
USING YOUR COMRA PALM
1hr
Once you have downloaded the coMra user
guide to your smart phone, tablet or computer,
follow the instructions on the app (or search
the index on the PDF) to choose a treatment.
Enter dis-ease, condition or keyword
FOREWORD
BEFORE YOU START
To power-up your coMra Palm, slide the on/o
switch to green.
Page 7
1hr
1hr
1hr
Variable (V)1K (1000 Hz)50 Hz5 Hz
10 mins5 mins2 mins1 min
Once on, the Frequency
buttons and corresponding display will light up.
and Time
Cycle through the two buttons to select the
time and frequency for your treatment as
shown in the coMra user guide.
TREATMENT POINT
1
Top of sternum150
Variable1000 Hz50 Hz5 Hz
mins
Hz
1 min2 mins5 mins10 mins
Page 8
1hr
Variable (V)1K (1000 Hz)50 Hz5 Hz
10 mins5 mins2 mins1 min
StartEnd1 min2 mins
mins
Variable1000 Hz50 Hz5 Hz
TREATMENT POINT
mins
Hz
1
Top of sternum150
x1
x1
2
sec
x2
Place your coMra Palm onto the treatment
point, using the raised bump on the surface of
the Start
button as the centre point.
Press the start button to begin the program.
The sounder will beep and the start button
will light up and pulsate indicating that the
program is running.
x1
Page 9
If you need to pause the program for any
x1
reason, press the start button once. The start
button will ash on/o to indicate the program
has paused.
x1
To continue on from pause, press the start
button once again.
x1
When the selected time comes to an end,
two beeps will sound indicating the end of
the program.
Page 10
To terminate the program while the program
x1
x1
is running, press and hold the start button for
two seconds. Two beeps will sound, indicating
the termination of the program.
2
sec
Repeat the process for all the points on the
x2
treatment plan.
When you have completed your treatment and
nished using your coMra Palm, slide the on/
o switch to red and power-down the device to
preserve battery life.
Page 11
FREQUENCY AND TIME DISPLAY
There are four indicating triangles for the
frequency setting (hertz) and four indicating
triangles for the time setting (minutes).
Once a program has started, the in-built timer
will count-down and display the remaining
minutes left for the program. When nished,
two beeps will sound and the time indication
will revert back to the selected start time.
StartEnd1 min2 mins
5-4-3
mins
Page 12
RECHARGING THE BATTERY
If your coMra Palm stops working during a
treatment program, it is an indication that
the battery is running out of charge. If this
happens, rst slide the on/o switch to red
and then slide back to green.
A three second continuous beep will conrm
if the battery needs charging. Slide the on/
o switch back to red and plug the micro end
of the USB cable into the micro USB port at
the rear of your coMra Palm, and the other
end into any powered USB port, or a mains
electrical socket (using a suitable adaptor).
Page 13
The red LED indicator next to the on/o switch
will light up and the battery will start charging.
1hr
When the battery is fully charged the red LED
indicator will switch o. A full battery charge
takes approximately 1 hour.
Your coMra Palm can be used while charging.
A full battery charge on your coMra Palm
should allow you approximately 30 mins of
daily treatment, for up to 10 days.
CLEANING YOUR COMRA PALM
Use a 3% solution of hydrogen peroxide, or
colloidal silver for disinfecting and cleaning
your coMra Palm.