Page 1
Thank you for choosing eLock.
CompX eLock® is a highly engineered lock with a motor-driven latch. Its uncompromising lock
control electronics include a non-volatile memory that stores 250 user / supervisor codes and
audit trail. With optional LockView® audit trail software, CompX eLock® remembers 1500 access
attempts. Programming is simple with numeric keypad or WindowsTM based LockView® software.
NUMERIC
KEYPAD
MAGSTRIPE
CARD
MAGSTRIPE / KEYPAD
DUAL SYSTEM
PROX
READER
Quick Programming Guide
1. GETTING STARTED:
a. The unit is shipped with no user / supervisor codes
b. Press and hold until the beeping stops
c. Input the new PIN (4 digit min) and press or present new card
d. This PIN / Card is now a supervisor in slot #001
2. ADD A USER:
a. Input a valid supervisor PIN and press or present valid supervisor card
b. Press and hold until beeping stops
c. Input the new user PIN (4 digit min) and press or present new card
3. ADD A SUPERVISOR:
a. Input a valid supervisor PIN and press or present valid supervisor card
b. Press and hold until beeping stops
c. Press and hold again until beeping stops
d. Input new supervisor PIN (4 digit min) and press or present NEW supervisor card
PROX READER / KEYPAD
DUAL SYSTEM
See programming
guide included
with optional
LockView®
software for
advanced
programming
instructions.
4. DELETE A USER OR SUPERVISOR:
a. Input a valid supervisor PIN and press or present valid supervisor card
b. Press and hold until beeping stops
c. Input the PIN to be deleted and press or present existing card to be deleted
5. ADD A USER WITH A SPECIFIC SLOT ASSIGNMENT:
a. Input a valid supervisor PIN and press or present valid supervisor card
b. Press and hold until beeping stops
c. Enter slot number that will be assigned to user and press
(example: to program slot 6 type 006 )
d. Input the new user PIN (4 digit min) and press or present NEW card
6. DELETE A USER WITH A SPECIFIC SLOT ASSIGNMENT:
a. Input a valid supervisor PIN and press or present valid supervisor card
b. Press and hold until beeping stops
c. Enter slot number to be cleared and press (example: to clear slot 6 type 006 )
d. Enter slot number to be cleared again and press (example: to clear slot 6 type 006 )
1
1
Page 2
CompX eLock® Accessories
AC ADAPTER
Part Numbers:
EL-2004-9VWB
(for use with the CompX eLock kit)
EL-2004-acWB
(for use with 12V electric strikes)
TORX HEAD
DRIVER FOR
FRIG KIT
(Torx head bit also available)
Part Number:
EL-dRV-15
LATCH SPLITTER
(for running up to 2 latches)
Part Number:
EL-2004-LS
MOTORIZED
LATCH*
Part Number:
EL-LaTch-3
SUPERVISOR
LATCH CABLE,
Part Number:
*
24”
EL-2004-Lc
®
HID
PROX USER,
SUPERVISOR CARD
Part Number:
EL-2004-Pc (no logo)
EL-2004-Pc-S (CSP logo)
LOCKVIEW
®
SOFTWARE KIT
(provided with 7 ft., 6-pin RJ11 cable,
1-USB dongle, 1 LockView® CD)
Part Number:
EL-LockViEW-3
RJ 11 EXTENSION
KIT, 4”
Part Number:
EL-2004-RJ kiT
MAGSTRIPE USER,
SUPERVISOR CARD
Part Number:
EL-2004-MSc (no logo)
EL-2004-MSc-S (CSP logo)
®
HID
PROX TAG
Part Number:
EL-2004-PT
2
HID is a trademark of HID Corporation. * These items are offered as Ser vice / Replacement Parts only.
Page 3
TEMPLaTE on
oPPoSiTE PagE
3
Page 4
1.81
7.77
CompX eLock® Surface Mounting
Use the diagrams below as a template for holes to be drilled and for mounting your CompX eLock®.
Put this template on the outside of the cabinet door where the eLock will go, and you can drill right through
it to mount your CompX eLock®. Mount with 2 shorter, steel colored screws.
NoTe:
Don't forget
to fill out and
return your
warraNTy
card!
* If you're using a battery
cable, then a wall adapter
is not required. If you're using
a wall adapter, then battery
cable is not required.
#1a
Hole Function
#1a, b Mounting Holes
required
#2 Battery Latch Cable
required
#3 Alarm
optional
#4 Battery Cable
optional
#5 RJ11 Port
required only if using LockView
#6 AC Wall Adapter
optional
#2
*
*
#3
#4
warNiNg:
Print this page and
1”
measure the line
above. It is ONE
INCH LONG. If it
#5
measures less than
or more than one
inch, the template
measurements also
need to be scaled
accordingly.
#6
FaiLure To
do so couLd
resuLT iN
misdriLLed
#1b
4
hoLes.
Page 5
CompX eLock® Latch Dimensions
Use the diagrams below as a template for holes to be drilled and for mounting your
CompX eLock® latch. Put this template on the inside of the cabinet door where the latch
1”
warNiNg: Print this
page and measure the line
above. It is ONE INCH
LONG. If it measures less
than or more than one inch,
the template measurements
also need to be scaled
accordingly.
FaiLure To do so
couLd resuLT iN
misdriLLed hoLes.
will go, and you can drill right through it to mount your CompX eLock® latch.
Mount with 4 longer, black colored screws.
LockView® Software
q Add, edit, view and delete users / supervisors and their credentials
q Add, edit and delete CompX eLocks
q Assign access rights between users / supervisors and CompX eLocks® in the database
q USB connection required
q Download, view, save, print, archive and delete audit trails
q Dual credential access available
q Set real time clock
q Time based access restrictions
q Create user groups
q WindowsTM based
LockView is a Registered Trademark of CompX International. Windows is a trademark
of the Microsoft Cor poration. Specifications may vary based on user application.
®
5
Page 6
TEMPLaTE on
oPPoSiTE PagE
6
Page 7
sample
sample
sample
CompX eLock® Warranty Card
These stickers are included with each CompX eLock® unit. Please review the information and keep the stickers in a
safe location as they may be needed to reset or identify a specific eLock unit. The codes shown here are not real codes.
They are representations of what the stickers will look like.
Sticker #1
Sticker #2
Sticker #3
2d bar code. Provides the same information as sticker
number three, but a 2d laser scanner is needed to
decode the information.
1d bar code. Place this sticker on or around the CompX
eLock® unit to help identify which codes to use if
resetting the lock is necessary.
Keep this sticker in a safe location.
Serial #: Needed to identify CompX eLock® units
Passcode: Unique to lock. Needed for LockView.
Prevents unauthorized LockView use
User Rst: Allows administrator or owner to erase
all user codes from eLock unit but keep
supervisor codes
Fact Rst: Erases all codes from eLock, including
settings. eLock unit will need to be set
up again after a Factory Reset
7
Page 8
sample
CompX eLock® Warranty Card
sample
Sticker
#3
Affix one copy of sticker #3
(see page 7) to the CompX
eLock® registration card
and return to CompX Fort
at address shown on the
registration card.
NoTe:
Don't forget
to fill out and
return your
warraNTy
card!
8
864.297.6655
compxelock.com
elock@compx.com
PO Box 200
Mauldin, SC 29662
Copyright © 2009 CompX Security ProductsPart #: 331926-0000-00
Revised 11.2.09
Loading...