How it Works
Computime
Loading...
TS TX
User Manual
9 pgs415.87 Kb0

Computime TS TX User Manual

MHSC Touch Screen Full Function Signature Command Operating Instructions
Touch Screen Full Function Signature Command (TSFSC)
OPERATING INSTRUCTIONS
Carefully inspect the contents for shipping damage. If any parts are missing or damaged, immediately contact the dealer from whom you purchased the kit or Ambient Technologies Technical Support at 1 800 398 6195. Do not attempt to install any part of the kit unless all parts are in good condition. Please keep this booklet for future reference.
CONTENTS OF KIT
Description Qty
Transmitter 1 Mounting Base 1 Battery Alkaline AAA 4 Instructions 1 #6 ¾” Screws, Zinc 2
FEATURES
• Large LCD display
•
Touch Screen Panel
•
Thermostatic Control Mode with Smart Mode Option
• Timer Mode
•
Sleep Mode to Save Battery
• Slide Function for Fast Operation
•
Three Flame Height Settings
•
Three Brightness Settings for Lights
• Three Speed Control for Blower
•
Auxiliary Control
• Low battery Indication
•
Child Proof Lock-out
•
Programmable Timer to turn blower on and off
• LCD Backlight
•
On-screen Security Codes Setup
Touch Screen Full Function Signature Command Operating Instructions
Page: 1
MHSC Touch Screen Full Function Signature Command Operating Instructions
Function Areas of the LCD Display
The figure on the right shows a typical display of the TSFSC LCD.
Information Bar
The information bar shows the room temperature, the “sending signal” radio icon, the low battery indication icon, the child-proof icon, and the flame icon. This area doesn’t have touch buttons.
- The room temperature will always be shown after power-up. It displays the room temperature from 40 °F to 99 °F. “Lo” and “HI” will be displayed when the room temperature is lower than 40°F or higher than 99°F, respectively.
- The radio icon will be shown when the transmitter is sending a signal.
- The low battery indication icon will be shown when the battery voltage is low.
- The child-proof icon will be shown when the child­proof mode is activated.
- The flame icon indicates the current flame height – Off, Low, medium, and High.
Touch Area
The touch area contains all touch buttons to control the transmitter. It consists of two categories: menus and adjustment arrows. The blue LED backlight lights up for 8 seconds when any of the touch buttons is pressed.
- The menus include TIMER, THERMO, LIGHT, FAN, and AUX.
- The adjustment arrows include ON/up and OFF/down. Their default function is to adjust the flame height. When a button from the menu is pressed, the ON/up and OFF/down buttons will temporarily become adjustment controls for the selected item. When the adjustment is done, the ON/up and OFF/down buttons go back to flame height controller again.
Logo Bar
The Logo Bar contains the brand logo: Signature Command System.
Important Safety Information
•
Read this manual thoroughly prior to programming or operating any remote control.
• This remote control system requires Four (4) “AAA” alkaline batteries to power the transmitter.
• This remote control system should only be used as described in this manual. Any other use is not
recommended and will void the warranty.
WARNING
Touch Screen Full Function Signature Command Operating Instructions
Page: 2
MHSC Touch Screen Full Function Signature Command Operating Instructions
Due to the sensitive temperature monitoring components in the transmitter, it is necessary to allow the transmitter to stabilize to room temperature before accurate room temperatures are displayed. If the transmitter is activated from a severe cold condition, allow 15 minutes for
NOTE
accurate temperature readings to appear on the LCD display.
Turn appliance OFF (at the Master Switch) if you are away from your house for an extended period of time. Never leave anything on top of the surface of the transmitter.
WARNING
Initialization and Setting up
Installing Batteries:
The remote transmitter has two battery compartments, one on each end of the
transmitter. Always change all four batteries at the same time.
To install batteries,
1. Press down the battery door tab and pull out to remove the battery
door.
2. Install the batteries as indicated inside the battery compartments.
3. Close the battery door by snapping in place.
4. When all four batteries are installed, the transmitter will initialize for
5 seconds and then is ready for use.
5. The batteries should be replaced every 6 months or when the low
battery icon indicator is displayed.
Changing Temperature Unit
When batteries are installed in the transmitter,
1. All available icons on the LCD will be turned on then be cleared.
2. The LCD will display temperature unit: °F. Use ON ∆ to toggle the units between °F and °C within
the first 5 seconds.
3. The transmitter enters Manual Mode
4. The LCD displays room temperature with the chosen unit.
Setting Privacy Code on Transmitter and performing Learn Function:
The remote transmitter privacy code is preset in factory. In the event of activation or interference from other nearby transmissions, change the code using the following procedures (learn function must be performed after changing the code):
1. Press the ON/arrow button and the TIMER button at the same time to enter privacy code setup mode.
2. The setup display is shown in the figure. The four digits on the top stand for the privacy code (as the
actual DIP switches on Monessen’s previous remotes). The default values of the four digits will be all “1”.
3. The first digit will be flashing upon entering the setup mode. Push the “ON” button to toggle its value
between “0” and “1”, and push the “OFF” button to jump to the next digit. The next digit will then start flashing and the first one stops flashing. Set up the four digits to your choice.
4. After setting up all the four digits, push “OFF” to finish the process and return to the previous mode.
Touch Screen Full Function Signature Command Operating Instructions
Page: 3
Loading...
+ 6 hidden pages
Buy Points How it Works FAQ Contact Us Questions and Suggestions Privacy Policy Cookie Policy Terms of Use