Compro technology IP70, IP55, IP60 User Manual

OK

2

1

IP55

/

IP60 IP70

Network Camera

Quick Start Guide

Please check the package contents on your hand. If anything is
missing, please don’t hesitate to contact your local distributor.

Network Camera RJ-45 LAN Cable

Power Adaptor (5V, 2A) Quick Start Guide

Installation CD

Screw for Ceiling Mount x 3

Screw Anchor x 3

Camera Layout Connecting the CablesPackage Contents

Light sensor (only available

on IP70)

Lens

IR Lamp x 6 (inside, only

available on IP70)

Microphone

Speaker

LED status indicator (dotted
line shows IP70 LED indicator )

USB Wireless adaptor connector

Audio Output

Reset Button

microSD card slot (on the

side)

Microphone Input

Power adaptor port

Ethernet Port

I/O port (2 in / 1 out)

LAN cable from PC to hub/router: If your LAN cable from PC has

been connected to the Cable/ADSL modem, please re-connect it
to the LAN port of your hub/router.

LAN port on camera: Use the bundled RJ-45 LAN cable to

connect the LAN port of the IP camera to the LAN port of your
hub/router.

Wireless adaptor (Optional accessory): If you have purchased

the Compro USB wireless adaptor, plug it into the USB port of IP
camera for wireless reception. The wireless connection port only
supports the wireless adaptors from Compro; please do not use
other USB adaptors on Compro IP camera.

Power: Attach the power adaptor to the camera’s power adaptor

port and connect the power plug to a power outlet.

Mounting the Camera Installing Camera Software

Follow the steps below to mount the camera on a at surface. Then
adjust the camera to the desired viewing angle.

1. Detach the metal mounting plate from the bracket by inserting a

at blade screwdriver into the rectangular hole on the wide end of

the bracket base and then pressing the screwdriver downward.

2. Place the side of the mounting plate that has protruding screw

holes against the mounting surface. Screw the mounting plate

into the mounting holes on the mounting surface. And fasten the

bracket to the mounting plate by clicking the plate into position.

To begin setup, insert the installation CD into your CD-ROM

drive, and the iWizard will start automatically. ( If it doesn’t,
browse the contents of the CD and run the ‘iWizard.exe’). Then,
select the language and the device you wish to set up.

The first step shows how to connect all the cables. Hit [Next]
twice to proceed with the 2nd step in which the iWizard scan
for available cameras on your local network. Then select your
camera from the list, and wait until the live video and camera
information are displayed on the right. (You can double-check
the device name and the MAC ID which are printed on the serial
number sticker on the back of the camera and on the package).

Click [Next] when you’re ready. Meanwhile, if you see the
Windows Security Alert dialog box during the search, please
choose [Unblock].

The default password is `admin.’ Enter a new password here

(please note down your new password). You can also click

[Next] to skip this process.

Check the camera name, date and time setting.

Choose whether to use Seedonk service to remotely access

your camera via Seednok platform. You may also use a dierent
Seedonk server by clicking on [Advanced Settings]. (If you enable
Seedonk service, you cannot use iDDNS service.)

Choose to obtain IP address automatically (DHCP) or manually

congure IP address. Also congure your connection port and
local power line frequency here. (If you enabled Seedonk service,
you won’t see connection port and power line frequency setting
here.)

Note: When dismounting the camera, follow step 1 to detach the
camera from the mounting plate. Do not pull the camera off the
mounting surface by force, as doing so may damage the bracket
base permanently and render future camera mounting impossible.

(Skip here if you do not have Compro wireless adaptor.) If you

This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received,
including interference that may cause undesired operation.

have purchased and connected the Compro wireless adaptor
to your IP camera, you can choose to connect wirelessly by
default. The wizard will search for available access points. Then
select one access point to use.

(Skip here if you enabled Seedonk service) If you didn’t

enable Seedonk service earlier, you can set up iDDNS service
here. To do so, click [Yes] and input your desired address name.
Then click [Check Availability] to check if the entered address
name has been used. When successful, you can click [Create
Shortcut] button to create a shortcut on your desktop for
convenient access.

(Skip this part if you didn’t enable Seedonk service.) You will

be asked to log in to your Seedonk account when you come
to Seedonk setup. If you don’t have a Seedonk account yet, you
can choose to create a Seedonk account and continue with
account registration (you need to read and accept the Seedonk
end user license, term of service, and privacy statement in order
to open a Seedonk account).

The iWizard starts programming your camera based on your

settings. Please wait patiently and DO NOT interrupt the
process. (If you chose not to use Seedonk service, you’ll get to
review your settings before saving them.)

Enter the correct passphrase, and choose the IP address
conguration.

The iWizard indicates the setup has completed successfully.

You can click on the URL to view the live video now. Click [Yes]

if you wish you set up another camera from scratch.

Finally, you can choose to install the ComproView by

choosing [Install]. Then follow the on-screen instructions to

install ComproView.

Note: The iDDNS is a free DDNS (Dynamic Domain Name
Service) service offered by Compro. If you are using floating
IP address, you need to apply for DDNS service to create a
hostname that links to your home or office IP address. Having
created the iDDNS address name, you can then enter `http://xxx
(input by yourself).iddns.org’ into your browser’s address bar to
access your IP camera. For complete information about iDDNS,
refer to the user manual in the installation CD.

Accessing the Camera via Internet Explorer

Please follow the steps below to access your camera via WebVUer on
Internet Explorer:

1. Open the Internet Explorer.

2. Enter the camera’s IP address in the address bar. (e.g. 192.168.0.100)

3. A dialog box that request the user name and password appears;

enter a valid user name and password, and then press OK. The

default user name and password are both `admin.’

4. After valid user name and password are entered, Internet Explorer

will prompt the installation of camera software from ‘Compro

Technology, Inc.’’

After a successful login to your Seedonk account, you may click
on [Download and Install] to install Seedonk Messenger. Or click
on [Next] to do so later manually.

6. And then the reconrmation dialog will appear on the screen.

Please press [Install] twice to install both the `USActiveX.cab’ and

`ComproClientActivex.cab’ on your system.

7. Meanwhile, the Windows Security Alert dialog may appear. Please

click [Unblock] to unblock it from rewall.

8. Now you can start using WebVUer on Internet Explorer to watch

live video and manage IP camera.

The iWizard performs system diagnosis based on your

network settings and alerts you for inappropriate settings
(which are marked with a question mark icon).

Compro Technical Support Information

Before you request technical support, please check the troubleshooting
section in the user manual. You may fill out the online form (www.
comprousa.com/feedback/) or directly email to [e-mail].

Compro Technology, Inc.
www.comprosecurity.com | Tel. [phone] | Fax [phone]
3F, No.12, Alley 6, Lane 45, Pao Shin Road, Hsintien District, New Taipei
City 231, Taiwan, R.O.C.

© 2011 Compro Technology, Inc. All rights reserved.
No part of this document may be copied or reproduced in any form or by
any means without the prior written consent of Compro Technology, Inc.
Compro Technology reserves the right to make revisions to this publication
without obligation to notify any person or entity of any such changes.

Compro Technology is the registered logo of Compro Technology,
Inc.
of Seedonk Inc. All other company and product names mentioned in this
document are registered trademarks of the respective companies.

Seedonk and Seedonk Messenger are registered trademarks

5. Click on the warning message and choose to install the ActiveX.

P/N: 3GA0310733