USER MANUAL
CSW-HD440EXT
Table of Contents
1.0 Introduction..........................................................................1
2.0 Specifications.......................................................................2
3.0 Package Contents................................................................2
4.0 Panel Descriptions...............................................................3
5.0 Connection and Operation..................................................3
Cab le a nd Conn ectivity Com p a n y
HDMI SWITCH SPLITTER 4×4 （matrix）by Cat5
HDMI SWITCH SPLITTER
Dear customer
Thank you for purchasing this product. For optimum performance and safety,
please read these instructions carefully before connecting, operating or adjusting
this product. Please keep this manual for future reference.
1.0 INTRODUCTION
This 4X4 Matrix HDMI SWITCH SPLITTER by cat5e/6 offers unprecedented
flexibility and convenience by routing high definition audio/video from any of four
HDMI video sources to any of 4 displays over HDMI cable or 4 remote displays
over inexpensive, standard CAT5e/6 cable. It eliminates the need to disconnect
and reconnect sources to a display equipped with one input.
Four receivers work with the Switch Splitter as a full functional module. Full
High-Resolution HDTV signals are supported up to a resolution of 1080p over
HDMI cable 15m or at a maximum distance of .40M over two pieces of CAT5e/6
cable. The 4X4 Matrix HDMI SWITCH SPLITTER works with HD-DVD players,
TiVo systems, HT PCs, and satellite set-top boxes that connect to an HDMI
display. Every source and display is accessible at all times by selecting it with an
IR remote or through RS232 port.
1.1 FEATURES
This product has many features that enable it to perform in a superior manner.
Among those features you will find:
l Allows any HDMI display to view any source at any time
l Allows any source to be displayed on multiple displays at the same time
l HDMI or DVI to HDMI cables are used to connect the inputs and the matrix
output
l Each Output includes one HDMI output and UTP output over cat5e/6, but only
one way is available at a time.
l Each UTP output is connected to a Receiver.
l UTP output extends signal up to 40m for 1080p by CAT-6 cable.
l Each Input includes an infrared Emitter, which is used to control the
long-distance source device by Remote Control.
l Each display's inputs can be switched with the IR remote control or through
RS232
l Support HDMI1.3b
l Support highest video resolution 1080p.
l Support 225MHz/2.25Gbps per channel (6.75Gbps all channel) bandwidth.
l Support 12bit per channel (36bit all channel) deep color.
l Support HDCP
l Support uncompressed audio such as LPCM.
l Support compressed audio such as DTS Digital, Dolby Digital（including
DTS-HD and Dolby True HD）.
１
HDMI SWITC H S PLITTER 4 4 ! matrix" by Cat5
2.0 SPECIFICATIONS
Signal Inputs/Output
HDMI Connector type A 19 pin female
Input DDC Signal 5 volts p-p (TTL)
Control Port RS-232 Female, Mini-Stereo
Output Signal HDMI output, UTP output
Operating Frequency
Vertical Frequency Range 50/60Hz
Video Amplifier Bandwidth 2.25Gbps/225MHz
Resolutions(HDTV)
Interlaced(50&60Hz) 480i,576i,1080i
Progressive(50&60Hz) 480p,576p,720p,1080p
Mechanical
Size of HDMI Switch Splitter (L-W-H)
Weight of HDMI Switch Splitter (Net) 2218g
Warranty
Limited Warranty 2 Years
Environmental
Operating Temperature
Operating Humidity 10% to 85 % RH (no condensation)
Storage Temperature
Storage Humidity 5% to 90 % RH (no condensation)
Power Requirement
Power Supply for HDMI switch splitter 5.5V DC@4A; 20W
Power Supply for Receiver 5V DC@2A; 5W
Regulatory Approvals
Converter Unit FCC,CE,UL
Power Supply UL,CE,FCC
Accessories Adapter
AC Power Adapter US standard, UK standard and so on
User Manual English version
441$ 202$ 45MM
Parts and Labor
0 % to +70%
-10% to +80%
Note: Specifications are subject to c hange without notice.
3.0 Package Contents
Before attempting to use this unit, please check the packaging and make sure the
following items are contained in the shipping carton:
Packaging of Main Unit
1) HDMI 4X4 Switch Splitter
#
HDMI SWITCH SPLITTER 4×4 （matrix）by Cat5
2) Remote Control
3) IR extension cable.(IR)
4) 5.5V@4A DC Power Supply
5) User’s Manual.
Packaging of Accessories
6) Four Receivers
7) Four pieces of Remote Control for Receivers
8) Four pieces of External infrared emitter (IE)
9) Four pieces of 5V DC @2A Power Supply.
4.0 PANEL DESCRIPTIONS
Please study the panel drawings below and become familiar with the structure.
HDMI 4X4 Matrix Switch Splitter
HDMI
DC/5V
DC INPUT
Receiver
4X4
Matrix
by CAT-5e/6
F
TMDS TMDS
Output D Output C Output B
HDMI DDC
DC/5V
IR
DDCHDMI
Output
Output A
HDMI DDC
F
Select
4321
TMDS TMDS
Output A
IR
Select
InputInput
Output B
Power
Select
Output C
Input 4 Input 3
IE 4
DDCHDMI
TMDS
Select
InputInput
1 2 3 4
43211 2 3 4
Output D
IE 3 IE 2
DDCInput
Input 2 Input 1
IE 1
321
4
IR Ext
RS232
Power
RS232
Select
5.0 Connection and Operation
5.1 Connection
1) Connect all source devices to the HDMI inputs on the Switch Splitter..
2) Either HDMI or UTP can be selected as signal output for Output A/B/C/D.
When choosing the HDMI as signal output, connect displays and main unit
directly over HDMI cable. When choosing UTP as signal output, connect
３
HDMI SWITCH SPLITTER 4×4 （matrix）by Cat5
receivers and main unit over cat5e/6 cable, and then connect output of
receivers to displays. (Note: HDMI and UTP of each output can not be
connected simultaneously)
3) Connect the 5.5V@4A power supply to the Switch Splitter, and 5V@2A power
supply to each receiver.
Attention: Insert / Extract cable gently.
5.2 Operation
1) The automatic connection when supplied with power
The available outputs will automatically connect to the available inputs
according to their sequence number. Meanwhile, the redundant available ports
(input or output) or unavailable ports will not be connected.
For example:
1. If outputs A, B, D are connected to three power-on TVs separately, and the
four inputs are all have its own source devices (work-on mode), then the power-on
Switch Splitter will make a connection as follow:
1→A 2→B 3→D
(Output C and input 4 are not connected)
2. If outputs A, C, D are connected to three power-on TVs separately, and
only three inputs have its source devices (work-on mode), then the power-on
Switch Splitter will make a connection as follow:
1→A 3→C
(Output B, output D, input2 and input4 are not connected)
2) Selecting source devices by buttons
Four buttons on the Switch Splitter are used to select source devices circularly
for inputs A, B, C, and D. Once you press the button, it will select next available
source device.
4) Selecting source devices by IR remote
1. Power button
The power button of the IR remote can control the power of the Switch
Splitter. Pressing this button, the power-on unit will be turned off. If you
press it again, the unit will be turned on.
2. Other buttons
Depending on outputs A, B, C, D, the other buttons of the IR remote can
be divided into four groups. Each group has five buttons: ‘off’— turn off its
outputs. 1, 2, 3, 4 are used to select input port accordingly.
5) Selecting source devices by RS232
①. Introduction of RS232 remote operation:
RS232 remote operation is mainly based on the “super terminal” of
Windows operation system. Its parameter should be: ANSI 4800 8-N-1-non
②. Operation
A. Connect the switch splitter to the COM of PC with a RS232 cable.
B. Chose the right COM when you setting “super terminal” and then set the
４
HDMI SWITCH SPLITTER 4×4 （matrix）by Cat5
parameter as follow:
Baud frequency：4800
Data bit: 8
Parity bit: N
Stop bit: 1
Data stream: NON
C. Inputting your instruction. The instruction should be two or three letter, and
finish with “Enter” button.
Please input next instruction in three seconds or the”Overtime instruction”
will appear.
The input instruction should be right, or you will be rejected with the “wrong
instruction”
If the input or output that you chose is not connected to devices or not in
power-on mode, “ineffective instruction” will inform you.
If your instruction is performed, you can see the instruction of “successful
operation”.
③. Instruction input method
A. Selecting source device
Sequence number of output (A/B/C/D) + sequence number of the input
(1/2/3/4) + “Enter”
For example: If you want display B to view source 3, then you can input “B3
“and finish with “Enter”.
B. Turning off an output
C + Sequence number of the output that you want to turn off (A/B/C/D) +
“Enter”
For example: If you want to turn off output B, then you can input CB, and
finish with “Enter”.
C. Turning off the Switch Splitter:
OFF + “Enter”
D. Turning on the Switch Splitter:
ON + “Enter”
E. Inquiry:
QS + “Enter”
This order enables you know which input and output are available and the
connections of input and output.
５
5.3 CONECTION DIAGRAM
HDMI SWITCH S PLITT E R 4 4 ! matrix" by Cat5
55 Ruta Ct. South Hackensack, NJ 07606
Toll Free: 800 526-0242
Email:
sales@comprehensivecable.com
customerservice@comprehensivecable.com
www.comprehensivecable.com
/
Loading...