Page 1
QUICK REFERENCE GUIDE PAGE 1
The purpose of this guide is to assist you in correctly operating your Intensity™ 10 unit. This
device should only be used under the continued supervision of a licensed physician. This guide
is not intended to replace or substitute the Intensity™ 10 Instruction Manual. PLEASE READ
THE INSTRUCTION MANUAL COMPLETELY BEFORE USING THIS DEVICE. Read, understand
and practice the warnings, cautions and operating instructions. Always follow the operating
instructions prescribed by your healthcare provider.
INTENSITY™ 10 UNIT
Top
Channel 1 and 2 sockets
1
1
Side Front Back
6
3
2
4
7
10
2
AC/DC adapter receptacle
3
T (time) and S (therapeutic part)
selection buttons
Channel 1 intensity increase button
4
Channel 1 intensity decrease button
5
LCD display
6
Channel 2 intensity increase button
7
Channel 2 intensity decrease button
8
LEAD WIRES
(2 SETS)
5
ELECTRODES
(2 SETS)
8
9
LCD DISPLAY
1
TENS therapeutic mode
Lock function indicator
2
Low-battery indicator
3
Treatment time
4
Timer symbol
5
Channel 1 intensity level
6
Channel 2 intensity level
7
Body part selection
8
Power on/o button
9
Belt clip
10
Battery compartment cover
11
2
3
4
5
11
1
6
7
8
For more information about your Intensity™ 10 unit, please visit us online at roscoemedical.com or call 1-800-871-7858.
Page 2
QUICK REFERENCE GUIDE PAGE 2
Steps 1 – 4 should be performed with the device turned OFF.
IMPORTANT!
Once the unit has been turned ON, do not remove electrodes
without rst turning OFF the device.
INSERT BATTERY
1
Press arrow and slide battery compartment
cover open. Insert 9V battery, matching the
+ and – ends to those in unit.
The included AC adapter may
also be used as a power source.
PLACE ELECTRODES
4
ON SKIN
Remove electrodes from
protective backing. Keep
backing to properly store
electrodes after use.
Apply electrodes to the
exact site indicated by
your doctor or therapist.
Make sure the skin at the
application site is clean
and dry.
See Electrode Placement Guide for more information.
CONNECT ELECTRODES
2
TO LEAD WIRES
Firmly insert
the red or black
end of the lead
wire pin (it
doesn’t matter
which one) into
the electrode
connectors.
Make sure no bare metal of the pins are exposed.
TURN DEVICE ON
5
Press the button in the center of the unit
to turn it ON. Check that electrodes are
securely placed on the skin before activating device.
CONNECT LEAD WIRES
3
TO TOP OF DEVICE
TOP VIEW
This unit operates
with one or two
sets of electrodes.
When using one set,
plug lead wire into
Channel 1 on top
of the unit. Use
Channel 2 to operate
a second set if
directed by your
healthcare provider.
SELECT THERAPEUTIC
6
PART PROGRAM
Press the S button.
Notice the ashing
icon. Continue to
press the S button
until you reach the
desired body part.
SELECT DESIRED
7
TREATMENT TIME
Press the T button
to select one of four
treatment times:
15 min, 30 min,
60 min and C for
continuous.
Press the T button
until you reach the
time prescribed
by your therapist
or doctor.
PROBLEMS WITH YOUR DEVICE?
ADJUST CHANNEL
8
INTENSITY
Press the intensity control
buttons for Channel 1
s to increase intensity
t to decrease intensity
until you reach the setting
recommended by your
physician or therapist.
Repeat for Channel 2 if both
channels are being used.
If stimulation is or becomes uncomfortable, reduce
intensity and consult your physician if problems persist.
SAFETY FEATURES
The Safety Lock Feature automatically locks
the settings if no changes have been made in the
panel for 30 seconds. This feature prevents accidental
changes to your settings. Press the down arrow on
or to unlock the device
Turn o the device by pressing and holding the
power on/o button. (Unlocked device rst.)
The device will automatically power o after 3
minutes of inactivity in the panel.
Low battery indicator signals when battery is
low. Replace battery when stimulation feels weaker.
Please see pages 26 and 27 of your Intensity™ 10 Instruction Manual for troubleshooting tips.
Loading...