Page 1
WARNING – This product contains chemicals known to the State of California to cause cancer, birth
defects and/or other reproductive harm. Thoroughly wash hands after installing, handling, cleaning,
or otherwise touching this product.
Hubbell Lighting, Inc. Life Safety Products • www.compasslightingproducts.com
Copyright© Hubbell Lighting, Inc., All Rights Reserved • Specications subject to change without notice. • Printed in U.S.A.
COMP0001_INST_SHT 7/12
LED Emergency Light
CU2/CU2RC
IMPORTANT SAFEGUARDS
When using electrical equipment, basic safety precautions should
always be followed including the following.
READ AND FOLLOW ALL SAFETY
INSTRUCTIONS
1. Do not let power supply cords touch hot surfaces.
2. Do not mount near gas or electric heaters.
3. Equipment should be mounted in locations and at heights where it will not readily be subject
to tampering by unauthorized personnel.
4. The use of accessory equipment not authorized by the manufacturer may cause an
unsafe condition.
5. Do not use this equipment for other than its intended purpose.
6. Servicing of this equipment should be performed by qualied service personnel.
INSTALLER:
•SEE UNIT LABEL FOR ADDITIONAL MODEL SPECIFICATIONS
•SAVE THESE INSTRUCTIONS FOR USE BY OWNER/OCCUPANT
RECYCLING INFORMATION
All steel, aluminum and thermoplastic parts are recyclable.
All cartons contain recycled materials.
Please recycle responsibly.
Page 2
INSTALLATION
WIRING DIAGRAM
WIRING DIAGRAM
Warning:
Unused wires must be capped using enclosed
wire nuts.
Fig. A (J-Box) Fig. B Fig. C
J-Box Mounting
1. Feed xture leads through main bottom case and connect AC power supply (Fig A).
2. Connect wires through J-Box. Main bottom case on J-Box and secure with screws.
3. Connect battery only after continuous AC power can be provided to the unit (Fig. B)
4. Align snaps and push housing directly onto main bottom case (Fig. C). Apply
continuous AC power and press “TEST” button to check light.
Conduit
1. Secure main bottom case to wall surface. Route wires through hole in conduit ange
and make
conduit connection.
2. Connect battery only after continuous AC power can be provided to the unit (Fig. B).
3. Align snaps and push housing directly onto main bottom case (Fig. C). Apply
continuous AC power and press “TEST” button to check light.
OPERATION
1. During an electrical power failure, the lamps will automatically come on for a minimum
of 90 minutes.
2. To test, depress the “TEST” switch. The emergency lamps will illuminate. When the
switch is released,
the lamps will go off.
CU2
CU2RC
WIRING DIAGRAM
TEST
CHARGER
BOARD
-
+
277 VOLT
120 VOLT
RED
BLACK
WHITE
NEUTRAL
NOTE: UNUSED LEAD TOBE PROPERLY
INSULATEDWITH WIRE NUT
OTHER APPROVEDMETHOD.
RED BLACK
RED
BLACK
BATTERY
LAMP LAMP
3.6V/ 1800MAH
RED
BLACK
REMOTE
RED
BLACK
CU2RC
INSTALLATION
WIRING DIAGRAM
WIRING DIAGRAM
Warning:
Unused wires must be capped using enclosed wire nuts.
Fig. A (J-Box) Fig. B Fig. C
Instructions for Emergency Lighting Fixture
IMPORTANT：
Small Battery inthis unit may not befull charged After electricity
is connected tounit . let batterycharge upfor at least 24 hours.Then
normal operation ofthis unit should take effect. To check,press
the " TEST " button . Thelight inside the unit shouldturn on.
FLEXIBLE CONDUIT ONLY
and press "TEST" button to check light.
connection.
and press "TEST" button to check light.
The lamps listedherein,when used according to theseinstructions
with this unitequipment,are in accordance with therequirements of
csa standard C22.2 NO . 141 . Install wiring toremote heads in accor-
dance with section 46 of the canadian electrical code,part I.
PLUG IN
J-Box Mounting
1. Feed fixture leads through main bottom case and connect AC power supply (Fig A).
2. Connect wires through J-Box. Main bottom case on J-Box and secure with screws.
3. Connect battery only after continuous AC power can be provided to the unit (Fig. B)
4. Align snaps and push housing directly onto main bottom case (Fig. C). Apply continuous AC power and
press “TEST” button to check light.
Conduit
1. Secure main bottom case to wall surface. Route wires through hole in conduit flange and make
conduit connection.
2. Connect battery only after continuous AC power can be provided to the unit (Fig. B).
3. Align snaps and push housing directly onto main bottom case (Fig. C). Apply continuous AC power and
press “TEST” button to check light.
OPERATION
1. During an electrical power failure, the lamps will automatically come on for a minimum of 90 minutes.
2. To test, depress the “TEST” switch. The emergency lamps will illuminate. When the switch is released,
the lamps will go off.
READY
TEST
CHARGER
BOARD
-
+
277 VOLT
120 VOLT
RED
BLACK
WHITE
NEUTRAL
NOTE: UNUSED LEAD TOBE PROPERLY
INSULATEDWITH WIRE NUT
OTHER APPROVEDMETHOD.
RED BLACK
RED
BLACK
BATTERY
LAMP LAMP
3.6V/ 900MAH
RED
BLACK
TEST
CHARGER
BOARD
-
+
277 VOLT
120 VOLT
RED
BLACK
WHITE
NEUTRAL
NOTE: UNUSED LEAD TOBE PROPERLY
INSULATEDWITH WIRE NUT
OTHER APPROVEDMETHOD.
RED BLACK
RED
BLACK
BATTERY
LAMP LAMP
3.6V/ 1800MAH
RED
BLACK
REMOTE
RED
BLACK
CU2
CU2RC
INSTALLATION
WIRING DIAGRAM
Instructions for Emergency Lighting Fixture
IMPORTANT：
Small Battery inthis unit may not befull charged After electricity
is connected tounit . let batterycharge upfor at least 24 hours.Then
normal operation ofthis unit should take effect. To check,press
the " TEST " button . Thelight inside the unit shouldturn on.
FLEXIBLE CONDUIT ONLY
and press "TEST" button to check light.
connection.
and press "TEST" button to check light.
The lamps listedherein,when used according to theseinstructions
with this unitequipment,are in accordance with therequirements of
csa standard C22.2 NO . 141 . Install wiring toremote heads in accor-
dance with section 46 of the canadian electrical code,part I.
PLUG IN
J-Box Mounting
1. Feed fixture leads through main bottom case and connect AC power supply (Fig A).
2. Connect wires through J-Box. Main bottom case on J-Box and secure with screws.
3. Connect battery only after continuous AC power can be provided to the unit (Fig. B)
4. Align snaps and push housing directly onto main bottom case (Fig. C). Apply continuous AC power and
press “TEST” button to check light.
Conduit
1. Secure main bottom case to wall surface. Route wires through hole in conduit flange and make
conduit connection.
2. Connect battery only after continuous AC power can be provided to the unit (Fig. B).
3. Align snaps and push housing directly onto main bottom case (Fig. C). Apply continuous AC power and
press “TEST” button to check light.
TEST
CHARGER
BOARD
-
+
277 VOLT
120 VOLT
RED
BLACK
WHITE
NEUTRAL
NOTE: UNUSED LEAD TOBE PROPERLY
INSULATEDWITH WIRE NUT
OTHER APPROVEDMETHOD.
RED BLACK
RED
BLACK
BATTERY
3.6V/ 1800MAH
RED
BLACK
REMOTE
RED
BLACK
CU2RC
Loading...