Compass Atom 6HV Instruction Manual

Page 1

Always use proper safety procedures when using RC aircraft

Page 2

Introduction

Congratulations on your purchase of the Compass Model Atom 6HV Electric Powered Helicopter. This model has been designed using the latest in state-of-the-art design technology. To achieve the best performance and reliability from this model, please read through these instructions carefully so you become familiar with the contents of this kit before assembly.

AMA Information

We strongly encourage all prospective and current R/C aircraft pilots to join the Academy of Model Aeronautics. TheAMAis a non-profit organization that provides services to model aircraft pilots. As an AMA member, you will receive a monthly magazine entitled Model Aviation, as well as liability insurance plan to cover against possible accident or injury. All AMA charter aircraft clubs require individuals to hold a current AMA sporting license prior to operation of their models. For further information, you can contact the AMA at:

Academy of Model Aeronautics

5151 East Memorial Drive

Muncie, IN47302

Warning

The radio-controlled model helicopter contained in this kit is not a toy, but a sophisticated piece of equipment. This product is not recommended for use by children. Radio-controlled models such as this are capable of causing both property damage and/or bodily harm to both the operator/assembler and/or spectator if not properly assembled and operated. Compass Model Ltd. assumes no liability for damage that could occur from the assembly and/or use/misuse of this product. Although the Atom 6HV is powered by a quiet, smooth-running electric motor, it should be assembled and operated with the same care as its larger glow engine counterparts. When operating your Atom 6HV, please exercise caution and safety.

Warranty

The warranty covers defects in material or workmanship or missing components to the original purchaser for 30 days from the date of purchase. Compass Model Ltd. will replace or repair, at our discretion, the defective or missing component. Defective components must be returned to our Distributor prior to replacement. Any part, which has been improperly installed, abused, crash damaged or altered by unauthorized agencies is not covered. Under no circumstances will the buyer be entitled to consequential or incidental damages. The components used in this kit are made from special materials designed for special applications and design strengths. We recommend that all replacement parts be original parts manufactured by Compass Model Ltd. to ensure proper and safe operation of your model. Any part used which was manufactured by any firm other than Compass Model Ltd. VOIDS all warranties of this product by Compass Model Ltd.

Warranty Procedures

Mail all warranty information within 15 days of original purchase date. If service is required, send the component in question (if not missing) together with a photocopy of your bill of sale and an accurate description of the problem and part. Ship components fully insured and prepaid. Compass Model Ltd. is not responsible for any shipping damages. We will, at our discretion, notify you of any costs involved, or ship it COD. You are required to pay all postage, shipping and insurance charges.

R/C Helicopter Safety

A model helicopter must be built exactly in accordance with the assembly instructions. Compass Model Ltd. has spent much time and efforts refining this product to make it reliable in operation and easy to build. Vibration and stress levels are high and all fasteners and attachments must be secure for safe operation. Safe operation is the responsibility of the builder/flyer and starts with careful construction and continues with selection and installation of reliable radio equipment and motor/engine. The need for safety is nowhere greater than at the flying field. A number of guidelines for safe flight have been developed by experienced flyers and are set down here. It is urged that they be read, understood and followed.

Attention:

rules to apply in your country/Flying field.

Attention:

Atom 6HV Max. rotor head rpm: 2000 U/min Atom 6HV Max. collective pitch range: +/- 12°

each country has its own security application which cannot be laid down here so prior to any flight request the

Atom 6HV Limitations

Page 3

Guidelines for Safe R/C Helicopter Flight

• Fly only at approved flying fields and obey field regulations.

• Follow frequency control procedures. Interference can be dangerous to all.

• Obtain assistance from experienced pilots.

• The Guidance provided by experienced pilots is valuable and sometimes necessary.

• Know your radio. Check all transmitter functions before each flight.

• Be aware that rotating blades are very dangerous and can cause serious injury.

• Never fly near or above spectators or other modelers.

• Do not fly r/c helicopter models near buildings, high voltage cables, trees or other obstacles.

• If a beginner, get help trimming the model first and flight training later.

• Don’t “track” the main blades by holding the tail boom. This is a temptation to builders who cannot hover yet and is very dangerous.

• Follow all recommended maintenance procedures for model, radio and motor.

• Only turn off the radio after the brushless motor is disconnected.

Necessary Items

In order to operate this model, you need to purchase the following items not kit-included.

6 channel or up radio and receiver.

3 standard servos.

1 gyro with rudder servo.

1x LiPo Battery 12S

or 2 packs 6S 2500~3300mah.

1x HV/BEC 12S.

Main Rotor

Length: up to 620mm

Hex Wrench Set

(1.5mm,2mm,2.5mm,3mm)

Threadlock

Cutter Knife

BEC

Grease

Needle Nose Pliers

Standard Servos

Bearing Retainer

Screw Driver

Pitch Gauge

Ball Link Sizing Tool Ball Plier

Swash Plate Tool

Pre-assembly Information

When first opening your Atom kit, you will notice that all of the parts are packaged and numbered to coordinate with the assembly step numbers of this instruction manual. All small hardware (nuts, bolts, washers, etc.) for each step are packaged separately within the main parts bags. When beginning a section, you will need to open only the bag with the corresponding number to the section you are about to start. It is suggested that you place all of the hardware in an open container (e.g., servo case) during assembly so as not to lose any of the small parts. It may also be helpful to familiarize yourself with the various sizes of screws, bolts, nuts, etc., as illustrated in the appropriate assembly section before you begin assembly. In most cases, at the end of each assembly section, there should be no parts remaining. Great care has been taken in filling the bags with the correct quantity of parts and hardware for each section. However, occasional mistakes happen. In the event that you find a parts shortage or are in need of technical assistance, please contact your local Compass Model parts dealer.

Page 4

In The Box

This model is packed according to assembling steps. Do not open all the bags at one time.

Open only one bag for each step of assemply when building.

Step 1 Step 2 Step 3

Tail Set Step 4 Step 5

Rotor Set

Step 7

Frame Set

70A HV ESC

Long Item

Step 10

Symbols & Assembling

Mishandling due to failure to follow these instructions may result in damage, personal injury or danger.

Use Blue Threadlock

Use Grease

Use AB Glue

Use Bearing Retainer

* Always apply blue Threadlock when fixing Bolts on Metal parts. * Always apply green retainer where bearings has to be fit into metal parts. * Do not over-tighten self tapping screws into plastic parts or you will strip the threads!

Page 5

Servo

M2.5x10 Self Tapping Bolt X 16

M2 5X10 Self Tapping Bolt.

2.5mm Washer X 16

Plastic Spacer x 4

The Servo installation is done without the supplied Servo Rubbers.

Servo

2 5mm Washer.

Servo Spacer

M2.5x10 Self Tapping Bolt

This Servo is installed in between the 2 frames. The Self Tapping Bolts are screwed from the inside.

Landing Gear

M3 x10 Self Tapping Bolt X 4

M3x5 Set Sc rew X 4

Use AB Glue

2.5mm Washer

Servo

M2.5x10 Self Tapping Bolt

M3x10 Self Taping Bolt

Struts

M3x5 Set Screw

Skid Cap

Tip: Do not over tighten the four 3 x 5mm

set screws as it can damage the landing struts.

Landing Gear Skid

Page 6

M3 Washer x4

Boom & Tail Rotor

Crimping Belt damages the Tensile Cords and will result in premature failure.

M3 Nylon Lock Nut x10

M2.5x6 Cap Head Bolt x2

M3x38 Cap Head Bolt x4

M3x14 Cap Head Bolt x2

M3x26 Cap Head Bolt x2

M3x25 Cap Head Bolt x2

M3x32 Cap Head Bolt x2

M2.5 x8 Self Tapping Bolt X 4

Use Threadlock

Be careful not to over tighten the Bolts when attaching the Tail Rotor Blades. The Tail Blades should be able to move with a slight amount of resistance within the Tail Blade Holders.

M3x32 Cap Head Bolt

M3 Nylon Nut

M3 Washer

M3 Nylon Nut

M3 Washer

M3x26 Cap Head Bolt

Insert the Tail Boom fully into the Tail Case before tightening the

2.5x6mm Bolts.

M3x14 Cap Head Bolt

These bolts are used only to compress the boom. Please do not screw them in completely.

M2.5x6 Cap Head Bolt

Bearing Retainer

M3 Nylon Nut

There are 2 grooves on the boom. The shorter groove is towards the tail while the longer one is towards the frame.

See Page Team Tips!

M3x40 Cap Head Bolt

Slide the Tail Boom through the Tail Boom Mount. Twist the Tail Belt 90° to the right before inserting it to the Idler Pulleys.

Boom

M2.5x8 Self Tapping Bolt

Page 7

M3 Nylon Lock Nut x1

M2.5x10 Cap Head Bolt x1

M3x27 Shanked Bolt x1

Main Gear

Main Shaft Clamp has to br mounted below the Bearing Block.

Main Shaft

Apply This Hole

Mast Collar

Lift the Main Shaft Collar upwards and secure to the Main Shaft by slightly tighten the Lock Screw. It is necessary to align the Lock Screw through the hole in the side of the Main Frame. While securing the Lock Screw, make sure that you are pushing down on the Main Shaft so that there will be no up/down play in the Main Shaft once the collar is secured.

Use Threadlock

See Page Team Tips!

To adjust the correct backlash between the Motor Pinion and the Main Gear loose the 4 Motor Mount Bolts, then fix them tightly with Threadlock.

M2.5x10 Cap Head Bolt

M3 Nylon Nut

M3x27 Shanked Bolt

Gear BacklashAdjustment: For smooth operation and performance, it is necessary to adjust the Gear Backlash properly. Excess Gear Backlash can cause premature Gear Wear and damage. Insufficient Gear Backlash can cause vibration, as well as overheating of the Motor and Speed Controller. Adjust the Gear Backlash by placing one piece of paper between the Gears to set the distance. When the Bolts are secure, remove the paper and test the Gear Backlash to insure that there is a slight amount of free movement between the gears.

Check the correct rotation of the Tail Rotor Blades. The Blade on the Top moves to the re ar. If the Tail Rotor rotates incorrectly, simply pull out the main shaft and twist the Belt in the other direction.

Page 8

M2.5 x8 Self Tapping Bolt X 4

M3x4 Set Screw x6

M4x4 Set Screw x2

M3 Nylon Lock Nut x1

M3x22 Shanked Bolt x1

Use Threadlock

Rotor,Washout & Swashplate

In this step, push the Flybar through the Flybar Collar, Flybar Holder, and Flybar ControlArm. Using set screws, fix theArms and Collars onto the Flybar. Make sure that both sides of the Flybar are of equal lengths.

M4x4 Set Screw

M3x4 Set Screw

See Page Team Tips!

M3X22 Shanked Bolt

Be sure to note the correct direction of the Flybar Paddles as shown in the diagram. It is very important to insure that the Paddles are in parallel to each other, as well as to the Flybar Control Arm Assembly.

M3x4 Set Screw

Washout Link

Swashplate

Adjust so that each side has exactly the same length

Paddle Insert

Flybar

M3 Nylon Nut

Paddle Insert

Thread

Paddle

See Page Team Tips!

Main Shaft

M2 5x8 Self Tapping Bolt.

Page 9

Equipment illustration

ESC

Esc

Pitch

To M o t o r

Vecro Tape

12S Battery

Aileron

Brushless Motor

Elevator

Rudder

Receiver

BEC

Ch6

The following Linkage lengths indications are basic values. PLEASE BE AWARE THAT THEY COULD VARY depend on used Servos andArms. Some fine adjustments are still needed in following setup steps.

Linkage

25mmx2

Please cut away 1.5mm from each Ball Link.

2mm

41mmx2

60mmx2

Page 10

Servo Screw

Servo Arm

2x6mm Cap Head Bolt

Stainless Balls

Most servo manufacturer provide extra long servo horn, please apply that and se tup the servo horn at 25mm to the center.

44.5mm

54.5mmx2

33.5mm

Do not apply plier to resize Ball Links. Pliers could

cause hidden damage to Ball Links and result in failure when operation.

Setup

Pitch

General Flight

Throttle Pitch

4 3 2

80%

75% 50%

25%

9 deg

4~5 deg

-5 deg

3D Style

Throttle Pitch

80%

10 deg

5 deg

0 deg

-5 deg

-10 deg

Compass Model Ball Links are build up on the tight side this allows you to adjust them to your personal needs. For this we suggest to use a Ball Link sizing tool.

The 6HV total pitch range is about 30°. If you s et the pitch too hi gh then flight time will be shortened.

Throttle Curve

100%

80%

60%

40%

20%

12345

Throttle Curve

100%

80%

60%

40%

20%

12345

Swash Type Setting

JR Futaba

Swash Type SWH

S3 120 SR3

Aile Elev Pitch

45% 45% 45%

Too high rate on Throttle curve setting could result in extreme high RPM on main rotor. Head speed over 2100 rpm could potentially cause serious mechanical failure.

Esc Setup

Timing: 22.5 deg No Brakes Very Soft Start

See Page Team Tips!

Page 11

Parallel

Make sure that the Flybar Control Arms and Paddles are in line as shown in the diagram.

Attention:

To do all Basic Setups first UNPLUG ESC from the receiver then use a 4.8V Receiver Battery for the setup.

Horizontal

Turn on the Transmitter, set the Throttle Stick into center position for 0 ° Pitch. Use the Subtrim menu to adjust the 3 Swash ServoArms to level.

Horizontal

Level the Swashplate by adjusting the links from the Servo Arms to the Swashplate. Use a Compass Swashplate Tool as guide. Then set level the Washout Arms.

06 0501 Swash Plate Tool-

3°

Mixing Arm

By adjusting the Links between Swashplate and MixingArms set the Mixing Arms to a 3° downward position. Adjust the Links between the Mixing Arms and the Main Blade Holder to set the Main Blade Pitch to 0°.

0 Pitch°

Page 12

13mm

90°

7°7°

Use this Hole for Tail Link Ball

With Rudder Stick in middle position, set the Rudder Servo Arm at 90° to the Tail Control Link. Set the Tail Blades to 7° Pitch.

Servo Direction Check

Turn the Transmitter on, your position has to be right behind the helicopters Tail. Make sure that the Swashplate Mode is set to CCPM 120°. Move the Sticks according to the drawings and check the reaction of the Swashplate and the Tail Pitch Plate. Check as well your Throttle settings. Adjust your Transmitter settings accordingly.

Mod 1

Mod 2

Swashplate Reaction

Tilt Right

Tilt Left

Aileron Check

Elevator Check

Pitch Check

Tilt Forward

Tilt

Backward

Ascent

Swash Plate

Descent

Rudder Check

Slide left

Tail Pitch Plate

Slide Right

Page 13

Canopy

M2.5x6 Self Tapping

Bolt X 2

Use AB Glue

ABA

M2.5x6 Self Tapping Bolt

Place the Canopy onto the Frames and mark the right position of the Canopy Inserts. Apply AB Glue to fix the Canopy Insert onto the canopy.

Rotor Direction

Canopy

Drill a 6.5mm D Hole here

Canopy Insert

When the Rotor spins clockwise the Tail Blades should turn clockwise as well watching the Tail Rotor from the Tail Fin side. If not Belt is installed the wrong way and has to be corrected.

Pre Flight Check

1. Ensure that receiver & transmitter battery are fully charged. 2 Check all bolts and screws are tight.. 3 Repeat step 10 to check all servo functions are correct.. 4 Ensure tail and gyro direction are correctly set..

5. Check that main blades, paddles and tail blades are installed in the right direction.

6. Check that there are no missing or damaged parts, never fly with any damaged parts.

7. Make sure all electronic devices are firmly fastened and connected.

8. Before starting the motor, make sure the IDLE switch is OFF and throttle stick is in the low position.

9. Only turn off the transmiter after turning off the receiver.

Page 14

Team Tips

General:

The Ball Links on the 6HV need to be resized.

Step 3

It is very important to resize the Ball Links for smooth travel, especially on the tail; because issues like tail wag, sluggish tail, or inconsistent Piro-rate will occur.

Step 4

It is vital not to over tighten the Main Gear Bolt, or it can cause the Autorotation Gear to slightly warp. This can cause a premature Belt failure, or reduce the lifetime of the Belt.

Step 5

: Leave About 0.1mm space between the Flybar Collar and the Flybar Holder, this avoids the Flybar to snap when flying.

Step 7:

For 3D flight please set Governor mode to High, Throttle curve at 75%~80% flat. To get extra flight time, please set ESC Timing to 7.5deg.

Thrust Bearing Direction

Main grips are factory preassembled; in case of reassembling make absolutely sure you use the correct “ID” ring at the correct position. Place the large ID Towards the Main Shaft and the small I.D. Towards the Blades during assembly.

Main Grip

Apply Grease Here

Larger ID

(IN)

Smaller ID

(OUT)

Page 15

Page 16

COMPASS MODEL (HK) LIMITED

www.compassmodel.com

Page 17

Parts List

6 HV

Version 1.0/2010

How to order your parts!

1. Check part number on the drawing

2. Use the part number to find the ORDER number on the list

3. Only use ORDER number for your parts order

As we continue to improve our products, this part list may not reflect all recent product amendments.

For more information, please refer to www.compassmodel.com

Page 18

02-5131

91 0003-

02 0113-

80 0206S-

02-0132F

02 0701-

Apply Grease Here

Larger ID

Main Grip

Thrust Bearing Direction

(IN)

Smaller ID

97-0920

02 0109-

02 0110-

60 8165-

80 0310-

80 0304-

Main grips are factory preassembled; in case of reassembling make absolutely sure you use the correct “ID” ring at the correct position. Place the large ID

(OUT)

Towards the Main Shaft and the small I.D. Towards the Blades during assembly.

80 0428-

02 0133-

91 0004-

07 0106-

63 8165-

02 0118-

79 0308-

61 4083-

80 0322S-

82 821003-

82 5131-

79 0510-

60 8 65-1

02 0543-

81 0304-

02 0511-

81 0304-

02 0539-

60 3083-

81 0404-

02 0701-

02 0553S-

80 0206S-

02 0531-

60 4083-

80 0208S-

60 4083-

02 0536G-

02 0540-

80 0206S-

02 0507-

80 2514-

82 2562-

Page 19

Part No. Part Description Order No. Order Description Qty,

)

02-0109 Delrin Dampener 8m 02-0110 Spindle Washer 8mm 02-0113 Spindle Shaft 8m 02-0118 Flybar Holder Collar 02-0132F Main Blade Holder Arm

02-0133 Main Blade Holder Bushing

02-0507 Mixing Arm 02-0511 Paddle Insert 02-0531 Mixing Arm Bushin 02-0536G Flybar Holder 02-0539 Flybar Colla 02-0540 Flybar Control Arm 02-0543 Flyba 02-0553S Paddle 02-0701 Stainless Link Ball 02-5131 Main Blade Holder Metal 07-0106 Rotor Hub 60-3083 Ball Bearing 3x8x3 60-4083 Ball Bearing 4x8x3 60-8165 61-4083 Flanged Bearing 4x8x3 63-8165 Thrust Bearing 8x16x5 79-0308 Button Head Bolt M3×8 79-0510 Button Head Bolt M5x10 80-0206S Cap Head Bolt M2x6 80-0208S Cap Head Bolt M2x8 80-0304 Cap Head Bolt M3x4 80-0310 Cap Head Bolt M3x10 80-0322S 80-0428 Shanked Bolt M4×28 80-2514 Cap Head Bolt M2.5×14 81-0304 Set Screw M3x4 81-0404 Set Screw M4x4 82-2562 Washer 2.6x5.2x0.3 82-5131 Washer 5.3×13×1 82-821003 Washer 8.2×10×0.3 91-0003 91-0004 97-0920 Rubber O-Ring 13×9×2

Ball Bearin

Shanked Bolt M3x22

lon Lock Nut M3 lon Lock Nut M4

8x16x5

02-0109 02-0110 02-0113 02-0118

02-0132F

02-5131

02-0507 02-0553S 02-0531S

02-0536G

02-0539

02-0540s

02-0543 02-0553S

02-0701

02-5131

07-0106

60-3083

60-4083

60-8165

61-4083

63-8165

79-0308

79-0510 80-0206S

80-0208S

80-0304

80-0310

80-0322S

80-0428

80-2514

81-0304

81-0404

82-2562

82-5131

82-821003

91-0003

91-0004

97-0920

Delrin Dampeners 8m Spindle Washers 8mm 2 pcs/ba Spindle Shafts 8m Flybar Holder Collars (Rotor Hub Main Blade Holder Arm se

Provided w 02-5131

Mixing Arm se Paddle se Bushing set (3 sizes Flybar Holder w; Bearings1 Flybar Collars 2 pcs/ba Flybar Control Arm se Flybars 2 pcs/ba Paddle se Stainless Link Balls 10 pcs/ba Main Blade Holder Metal 1 set/ba Rotor Hub set 1 set/ba Ball Bearings 3x8x3 5 pcs/ba Ball Bearings 4x8x3 5 pcs/ba Ball Bearings 8x16x5 Flanged Bearings 4x8x3 5 pcs/ba Thrust Bearings 8x16x5 2 set/ba Button Head Bolts M3×8 10 pcs/ba Button Head Bolts M5x10 10 pcs/ba Cap Head Bolts M2x6 10 pcs/ba Cap Head Bolts M2x8 10 pcs/ba Cap Head Bolts M3x4 2 pcs/ba Cap Head Bolts M3x10 10 pcs/ba Shanked Bolts M3x22 Shanked Bolts M4×28 2 pcs/ba Cap Head Bolts M2.5×14 10 pcs/ba Set Screws M3x4 10 pcs/ba Set Screws M4x4 10 pcs/ba Washers 2.6x5.2x0.3 10 pcs/ba Washers 5.3×13×1 10 pcs/ba Washers 8.2×10×0.3 2 pcs/ba

lon Lock Nuts M3 lon Lock Nuts M4 10 pcs/ba

Rubber O-Ring set 13×9×2 4 pcs/ba

2 pcs/ba

2 pcs/ba 2 pcs/ba

2 set/ba

1 set/ba 2 pcs/ba 2 pcs/ba 6 pcs/ba

cs/ba

2 pcs/ba

cs/ba

Page 20

80 0208-

02 0250-

90 0201-

63 4094-

60 4094-

81 0305-

02 0209-

82 3402-

80 2506-

61 5134-

02 1211-

98 1800B-

05 0227-

05 0231-

02 0262-

82 5808-

82 5804-

02 0229-

61 5134-

02 0214-

80 2506-

02 0225-

80 0314-

02 0264A-

60 3092-

91 0003-

80 0208S-

02 0701-

02 0264B-

91 0003-

02-0205

06 0208-

06 0222-

60 7113-

05 0229-

60 7113-

02 0213-

02 0230-

06 0213-

80 2508-

05-0227Z

02-8205

06 0213S-

02-8206

Page 21

Part No. Part Description Order No. Order Description Qty,

02-0205 Tail Blade Link 02-0209 Tail Rotor Hu 02-0213 Tail Pitch Slider 02-0214 Tail Shaft 02-0225 Grooved Pi 02-0229 Gear box frame 02-0230 Tail hinge 02-0250 Tail Blade 02-0262 Tail rotor pulle 02-0264AB Tail blade holder 02-0701 Stainless Link Ball 02-1211 Tail pitch plate w, BB 02-8205 Tail Pitch Control unit 02-8206 Tail Case Set 05-0227 Gear box se 05-0229 Tail pitch slider 05-0231 Gear Box Membe 06-0208 Tail pitch arm 06-0213 Tail pitch H arm 06-0222 60-3092 Ball Bearing 3x9x2.5 60-4094 Ball Bearing 4x9x4 60-7113 Ball Bearing 7x11x3 61-5134 Flanged Bearing 5x13x4 63-4094 Thrust Bearing 4x9x4

80-0208

80-0208S Cap Head Bolt M2x8

80-0314 80-2506 80-2508 81-0305 82-3402 82-5804 82-5808 90-0201 91-0003 98-1800B

Guide Pin Bol

Cap Head Bolt M2x8

Cap head Bolt M3x14 Cap Head Bolt M2.5x6 Cap Head Bolt M2.5x8 Set Scre Washer 3.2x5.2x0.3 Washer 5x8x0.4 Washer 5x8x0.8 Hexagonal nut2x1

lon Lock Nut M3

Tail belt 3M1800 Bando

02-0205S

02-0209 02-0213 02-0214

02-0205S

02-0229

02-0230S

02-0250

02-0262S

02-0264AB

02-0701 02-1211 02-8205 02-8206

05-0227

05-0229S

05-0231 06-0213S 06-0213S

06-0222

60-3092

60-4094

60-7113

61-5134

63-4094

80-0208

80-0208S

80-0314

80-2506

80-2508

81-0305

82-3402

82-5804

82-5808

90-0201

91-0003

98-1800B

Tail Blade Links w, Pin 2 pcs/ba Tail Rotor Hu Tail Pitch Slider 1 pcs/ba Tail Shafts 2 pcs/ba Provided w, 02-0205S Gear box frame w, B Tail Hing with Pin 1 set/ba Tail Blade set 2 pcs/ba Tail rotor pulley with spring pin 1 pcs/ba

Tail blade holder 2 pcs/ba

Stainless Link Balls 10 pcs/ba Tail pitch plate w, BB 1 pcs/ba Tail Pitch Control unit 1 set/ba Tail Case Set 1 set/ba Gear box se Tail Pitch Slider w. BB 1 pcs/ba Gear Box Membe Tail pitch arm w, H-arm & Pin 1 set/ba Tail pitch arm w, H-arm & Pin 1 set/ba Guide Pin Bolts Ball Bearings 3x9x2.5 4 pcs/ba Ball Bearings 4x9x4 5 pcs/ba Ball Bearings 7x11x3 2 pcs/ba Flanged Bearings 5x13x4 2 pcs/ba Thrust Bearings 4x9x4 2 pcs/ba Cap Head Bolts M2x8 10 pcs/ba Cap Head Bolts M2x8 10 pcs/ba Cap head Bolts M3x14 Cap Head Bolts M2.5x6 10 pcs/ba Cap Head Bolts M2.5x8 10 pcs/ba Set Scre Washer 3.2x5.2x0.3 10 pcs/ba Washer 5x8x0.4 10 pcs/ba Washer 5x8x0.8 10 pcs/ba Hexagonal nut2x1 10 pcs/ba

lon Lock Nuts M3 10 pcs/ba

Tail belt 3M1800 Bando 1 pcs/ba

1 pcs/ba

1 set/ba

2 pcs/ba

cs/ba

10 pcs/ba

cs/ba

Page 22

80 2505-

02 0601-

61 2562-

02 0519G-

02 0535-

80 0206S-

07 8410-

06-0410S

91 0003-

80 2510-

02 0503G-

02 0532-

05 0606-

07-0623

60 4083-

80 0206S-

80 2514-

02 0518-

07 4501-

80-0327

62 121816-

7 03069-

60 12215-

79 0306-

07 4603-

07 0621-

60 12215-

07 0622-

Page 23

Part No. Part Description Order No Order Description Qty,

)

02-0503G Washout Base (gre 02-0518 Washout Link 02-0519G Phasing Control Rin 02-0532 Bushin 02-0535 Washout Control Arm 02-0601 05-0606 Main Shaft Lock Clamp (Ø 06-0410S Swashplate Pin 07-0621 Autorotation Hu 07-0622 Autorotation Sleev 07-0623 Main Pulley Hu 07-4501 07-4603 Main Gear Molded 07-8410 Swashplate 60-12215 Ball Bearing 12x21x5 60-4083 Ball Bearing 4x8x3 61-2562 Flanged Bearing 2.5x6x2.6 62-121816 One Way Bearing 12x18x16 79-0306 Button Head Bolt M3x 80-0206S Cap Head Bolt M2x6 80-0327 Shanked Bolt M3x27 80-2505 Button Head Bolt M2.5X5 80-2510 Cap Head Bolt M2.5×10 80-2514 91-0003

Main Shaft

Main Pulle

Cap Head Bolt M2.5x14

lon Lock Nut M3

(grey)

02-0503G

02-0518

02-0519G

02-0531S

02-0535

02-0601 05-0606S 06-0410S 07-0621

07-0622

07-0623

07-4501

07-4603

07-8410

60-12215

60-4083

61-2562

62-121816

79-0306 80-0206S

80-0327

80-2505

80-2510

80-2514

91-0003

Washout Base (gre Washout Links 2 pcs/ba Phasing Control Ring (gre Bushing set (3 sizes Washout Control Arm set 2 pcs/ba Main Shaft Main Shaft Lock Clamp set (Ø 10mm Swashplate Pin Set 1 set/ba Autorotation Hub w, One Way Bearin Autorotation Sleev Main Pulley Hu Main Pulley Main Gear Molded 1 pcs/ba Swashplate 1 set/ba Ball Bearings 12x21x5 2 pcs/ba Ball Bearings 4x8x3 5 pcs/ba Flanged Bearings 2.5x6x2.6 10 pcs/ba One Way Bearing 12x18x16 1 pcs/ba Button Head Bolts M3x Cap Head Bolts M2x Shanked Bolts M3x27 2 pcs/ba Button Head Bolts M2.5X5 10 pcs/ba Cap Head Bolts M2.5×10 10 pcs/ba Cap Head Bolts M2.5x14

lon Lock Nuts M3 10 pcs/ba

1pcs/ba

1 pcs/ba 6 pcs/ba

cs/ba

1pcs/ba

1 pcs/ba 1 pcs/ba 1 pcs/ba

cs/ba

10 pcs/ba 10 pcs/ba

cs/ba

Page 24

80 0308-

78 0308-

07 0819-

07 0831R-

02 0805-

02 1805-

60 10195-

02 0605G-

07 8302-

07 0812-

07 0806-

05 0805-

60 3095-

80 0312-

02 0848-

07 0907-

02 0847-

06 0843-

02 1825-

07 0307-

60 8165-

07 4310-

81-0404

07 0310N-

C-5026-540

06 0305-

80 0310-

07 0831L-

80-0325

81-0316

02 0822-

81 0305-

02 0821-

02 0820-

a:82-3201

b:80-0338

c:80-0306

d:95-0310

e:80-0314

f:95-2508

Page 25

Part No. Part Description Order No. Order Description Qty,

)

02-0605G Bearing block uppe 02-0805 Cross Member M3x30 02-1805 Cross member set M3x30 02-0820 Skid End Ca 02-0821 Landing Gear Skid 02-0822 Landing Gear Strut (3D Plus 02-0847 Frame Membe 02-0848 Frame Membe 02-1825 Tail Boom Moun 05-0805 06-0305 Frame Connector w, 06-0843 Gyro Mount (6HV 07-4310 6HV Pinion Gear (10t 07-0307 6HV Pinion Bearing Mount 07-0310NNew Motor moun 07-0806 Guide Pulley Moun 07-0812 6HV Canopy Standof 07-0819 6HV Battery Moun 07-0831L 6HV Side Frame (Left 07-0831R6HV Side Frame (Right 07-0907 Swashplate Guide 07-8302 Guide pulley se 60-10195 Ball Bearing 10x19x5 60-3095 Ball Bearings 3x9x5 60-8165 Ball Bearings 8x16x5 78-0308 80-0306 Cap Head Bolt M3x6 80-0308 Cap Head Bolt M3x8 80-0310 Cap Head Bolt M3x10 80-0325 Cap Head Bolt M3x25 80-0312 Cap Head Bolt M3x12 80-0314 Cap Head Bolt M3x1 80-0338 Cap Head Bolt M3x38 81-0305 Set Screw M3x5 81-0316 Set Screw M3x1 81-0404 Set Screw M4x 82-3201 Washers 3.2x10x1.2 95-2508 Self Tapping Bolt 2.5x8 95-0310 Self Tapping Bolt 3x10 C-5026-540 12s motor for 6HV kv 54

Guide Pulle

Flat Head Bolt M3x8

02-0605G

02-0805 02-1805 02-0820 02-0821

02-0822 02-0845S 02-0845S

02-1825s

05-0805

06-0305

06-0843

07-4310

07-0307

07-0310N

07-0806

07-0812

07-0819

07-0831

07-0907

07-8302 60-10195

60-3095

60-8165

78-0308 80-0306 80-0308

80-0310 80-0325 80-0312 80-0314 80-0338

81-0305

81-0316 81-0404

82-3201 95-2508 95-0310

C-5026-540

Bearing block upper se Cross Member set M3x30 5 pcs/ba Cross member set M3x30 2 pcs/ba Skid End Cap set 4 pcs/ba Landing Gear Skids w. Caps2 Landing Gear Struts (3D Plus Frame Member se Frame Member se Tail Boom Mount se Guide Pulley se Frame Connector w, Bolts(Plastic Gyro Mount (6HV 6HV Pinion Gear (10t 6HV Pinion Bearing Mount 1 set/ba

ew Motor moun Guide Pulley Moun 6HV Canopy Standof 6HV Battery Moun 6HV Side Frame 2 pcs/ba 6HV Side Frame 2 pcs/ba Swashplate Guide 1 pcs/ba Guide pulley se Ball Bearings 10x19x5 4 pcs/ba Ball Bearings 3x9x5 2 pcs/ba Ball Bearings 8x16x5 2 pcs/ba Flat Head Bolts M3x8 Cap Head Bolts M3x Cap Head Bolts M3x8 10 pcs/ba Cap Head Bolts M3x1 Cap Head Bolts M3x25 10 pcs/ba Cap Head Bolts M3x1 Cap Head Bolts M3x1 Cap Head Bolts M3x38 10 pcs/ba Set Screws M3x5 10 pcs/ba Set Screws M3x1 Set Screw M4x Washers 3.2x10x1.2 10 pcs/ba Self Tapping Bolts 2.5x8 10 pcs/ba Self Tapping Bolts 3x10 10 pcs/ba 12s motor for 6HV kv 54

1 pcs/ba

cs/ba 2 pcs/ba 4 pcs/ba 4 pcs/ba

1 set/ba 2 pcs/ba 2 pcs/ba 1 pcs/ba

1 set/ba

1 pcs/ba 1 pcs/ba 2 pcs/ba 1 pcs/ba

1 set/ba

10 10 pcs/ba

10 pcs/ba

10 pcs/ba 10 pcs/ba

10 pcs/ba

10pcs/ba

1 pcs/ba

cs/ba

Page 26

02 0810SG-

02 0853-

07 0852P-

(07-0852)

02 0709-

40 2660-

95 2508-

06 0851-

02 0826-

82 3201-

05 0825T-

02 0823B-

02 0818-

80 0332-

02-0814S

02 0823A-

06 0823AB-

82 3201-

80 0326-

91 0003-

02 0816T-

02 0813-

02 BC-

80 2508-

40 2015-

VBT270

40 2530-

02-0701

40 2510-

40 2550-

40 2035-

40 2040-

Page 27

Part No. Part Descriptio

)

02-0701 Stainless link balls 02-0709 Ball Link

02-0810S 02-0813 Tail Boom Brace Connecto 02-0814S Tail Boom Brace 530mm 02-0816T Vertical Fin Carbon 02-0818 Tail Control Rod Guide Clam 02-0823AB Tail Boom Support Clam 02-0826 Tail Boom 705mm 02-0853 Canopy Rubber Gromme 02-BC 05-0825T Horizontal Fin Carbon (6HV 06-0823AB Vertical Fin Clam 06-0851 Canopy Insert 07-0852 Fiberglass Canopy (6HV 07-0852P Painted FG Canopy (6HV 40-2510 Link Rod 10mm 40-2015 Link Rod 15mm 40-2530 Link Rod 30mm 40-2035 Link Rod 35mm 40-2040 Link Rod 40mm 40-2550 Link Rod 50mm 40-2660 Tail Control Rod 2X660 80-0326 Cap Head Bolt M3x26 80-0332 Cap Head Bolt M3x32 80-2508 Cap Head Bolt M2.5x8 82-3201 Washer 3.2x10x1.2 91-0003 95-2508 VBT270 Velcro tape

Thumb Screw (gold

Blade Caddie（50/90）

lon Lock Nut M3

Self Tappin

Bolt 2.5x8

Order No. Order Descriptio

02-0701 02-0709

02-0810SG

02-0813S 02-0814S

02-0816T

02-0818S

02-0823AB

02-0826 02-0853

02-BC

05-0825T

06-0823AB

06-0851 07-0852

07-0852

E-LG-07 E-LG-07 E-LG-07 E-LG-07 E-LG-07 E-LG-07 40-2660S

80-0326 80-0332 80-2508 82-3201 91-0003 95-2508

VBT270

Stainless link balls 10 pcs/bag Ball Links 10 pcs/ba

Thumb Screw set (gold Tail Boom Brace Connector se Tail Boom Brace set 530m Vertical Fin Carbon 1 pcs/ba Tail cControl Rod Guide Clamp set 4 pcs/ba Tail Boom Support Clam Tail Boom 705mm 2 pcs/ba Canopy Rubber Grommet se Blade Caddie（50/90） Horizontal Fin Carbon (6HV Vertical Fin Clam Canopy Insert 1 set/ba Fiberglass Canopy (6HV Painted FG Canopy (6HV

Link Rod set (6HV)

Tail Control Rod 2X660 1 pcs/ba Cap Head Bolts M3x2 Cap Head Bolts M3x3 Cap Head Bolts M2.5x8 10 pcs/ba Washers 3.2x10x1.2 10 pcs/ba

lon Lock Nuts M3 10 pcs/ba Self Tapping Bolts 2.5x8 Velcro tape 4 pcs/bag

Qty,

4 pcs/ba 4 pcs/ba 2 pcs/ba

1 set/ba

10 pcs/ba

1 pcs/ba 1 pcs/ba

1 set/ba

1 pcs/ba 1 pcs/ba

1 set/ba 1 set/ba 1 set/ba 1 set/ba 1 set/ba 1 set/ba

10 pcs/ba 10 pcs/ba

cs/ba

Page 28

COMPASS MODEL (HK) LIMITED

www.compassmodel.com