Page 1
2.1
05/20/2010
Page 2
Page 3
Academy of Model Aeronautics
5151 East Memorial Drive
Muncie, IN47302
Introduction
Warning
Warranty
AMA Information
The warranty covers defects in material or workmanship or missing components to the original purchaser for 30 days from
the date of purchase. Compass Model Ltd will replace or repair, at our discretion, the defective or missing component.
Defective components must be returned to our Distributor prior to replacement.
Any part, which has been improperly installed, abused, crash damaged or altered by unauthorized agencies is not covered.
Under no circumstances will the buyer be entitled to consequential or incidental damages. The components used in this kit
are made from special materials designed for special applications and design strengths. We recommend that all replacement
parts be original parts manufactured by Compass Model Ltd to ensure proper and safe operation of your model. Any part
used which was manufactured by any firm other than Compass Model Ltd VOIDS all warranties of this product by Compass
Model Ltd.
We strongly encourage all prospective and current R/C aircraft pilots to join the Academy of ModelAeronautics. The AMA is
a non-profit organization that provides services to model aircraft pilots. As an AMA member, you will receive a monthly
magazine entitled Model Aviation, as well as liability insurance plan to cover against possible accident or injury. All AMA
charter aircraft clubs require individuals to hold a current AMA sporting license prior to operation of their models. For
further information, you can contact the AMA at:
Congratulations on your purchase of the Compass Model 3D Plus Nitro Powered Helicopter. This model has been designed
using the latest in state-of-the-art design technology. To achieve the best performance and reliability from this model, please
read through these instructions carefully so you become familiar with the contents of this kit before assembly.
Warranty Procedures
Mail all warranty information within 15 days of original purchase date. If service is required, send the component in
question (if not missing) together with a photocopy of your bill of sale and an accurate description of the problem and part.
Ship components fully insured and prepaid. Compass Model Ltd is not responsible for any shipping damages. We will, at our
discretion, notify you of any costs involved, or ship it COD. You are required to pay all postage, shipping and insurance
charges.
R/C Helicopter Safety
A model helicopter must be built exactly in accordance with the assembly instructions. Compass Model Ltd has spent much
time and efforts refining this product to make it reliable in operation and easy to build. Vibration and stress levels are high and
all fasteners and attachments must be secure for safe operation. Safe operation is the responsibility of the builder/flyer and
starts with careful construction and continues with selection and installation of reliable radio equipment and motor/engine.
The need for safety is nowhere greater than at the flying field. A number of guidelines for safe flight have been developed by
experienced flyers and are set down here. It is urged that they be read, understood and followed.
Each flying field has its own sets of safety guidelines which cannot be expressed here, so prior to any flight, refer
to the guidelines at your Flying Field.
Attention:
The radio-controlled model helicopter contained in this kit is not a toy, but a sophisticated piece of equipment. This product
is not recommended for use by children. Radio-controlled models such as this are capable of causing both property damage
and/or bodily harm to both the operator/assembler and/or spectator if not properly assembled and operated. Compass
Model Ltd. assumes no liability for damage that could occur from the assembly and/or use/misuse of this product. The 3D
Plus is a large glow powered model, it should be assembled and operated with special care. When operating your 3D Plus,
please exercise caution and safety.
Page 4
• Fly only at approved flying fields and obey field regulations.
• Follow frequency control procedures. Interference can be dangerous to all.
• Obtain guidance from experienced pilots.
•
• Know your radio. Check all transmitter functions before each flight.
• Be aware that rotating blades are very dangerous and can cause serious injury.
• Never fly near or above spectators or other modelers.
• Do not fly r/c helicopter models near buildings, high voltage cables, trees or other obstacles.
• If a beginner, get help trimming the model first and flight training later.
• Don’t “track” the main blades by holding the tail boom. This is a temptation to builders who cannot hover yet and is very dangerous.
• Follow all recommended maintenance procedures for model, radio and motor.
• Only turn off the radio after the engine is shut down.
The guidance provided by experienced pilots is often valuable and sometimes necessary.
Necessary Items
Bearing Retainer
At least a 6 channel radio and receiver
4 standard servos.
1 gyro with rudder servo.
5V receiver battery
or 2 cell li-po battery with a regulator.
Grease
Needle Nose Pliers
Screw Driver
Hex Wrench
(1.5mm,2mm,2.5mm,3mm)
Cutter Knife
Main Rotor Blades
Pitch Gauge Ball Link Sizing Tool
Ball Link Plier
In order to operate this model, you need to purchase the following items not kit-included.
Swashplate tool
Guidelines for Safe R/C Helicopter Flight
Thread Lock
Battery
Gyro
Servos
Engine Starter Glow Igniter
Starter Shaft
Fuel Filter
Class 50 Engine
Muffler for 50 Class
Glow Fuel for
Model Engines
Fuel Pump
Length: 600~ 620mm
Page 5
Step 1
Step 2
Step 3
Long items
Tail Set Step 4 Step 5
Rotor Head
Step 7 Step 9 Frame set Step 12
In the Box
This model is packed according to assembling steps. Do not open all the bags at one time.
Open only one bag for each step of assemply when building.
Use AB Glue
A
B
Use Blue Threadlock
Use Grease
Mishandling due to failure to follow these instructions may result in damage, personal injury or danger.
Symbols & Assembling
* Always apply blue Threadlock when fixing Bolts on Metal parts.
* Always apply green retainer where bearings has to be fit into metal parts.
* Do not over-tighten self tapping screws into plastic parts or you will strip the threads!
G
Use Bearing Retainer
When first opening your 3D Plus kit, you will notice that all of the parts are packaged and numbered to coordinate with the
assembly step numbers of this instruction manual. All small hardware (nuts, bolts, washers, etc.) for each step are packaged
separately within the main parts bags. When beginning a section, you will need to open only the bag with the corresponding
number to the section you are about to start. It is suggested that you place all of the hardware in an open container (e.g., servo
case) during assembly so as not to lose any of the small parts. It may also be helpful to familiarize yourself with the various
sizes of screws, bolts, nuts, etc., as illustrated in the appropriate assembly section before you begin assembly. In most cases, at
the end of each assembly section, there should be no parts remaining. Great care has been taken in filling the bags with the
correct quantity of parts and hardware for each section. However, occasional mistakes happen. In the event that you find a
parts shortage or are in need of technical assistance, please contact your local Compass Model parts dealer.
Pre-assembly Information
Page 6
0
10
20
30
40
1
Landing Gear
Tip:Do not over tighten
the four 3 x 5mm set
screws as it can damage
the landing struts.
Use AB Glue
A
B
M3 x10 Self Tapping
Bolt X 8
M3x5 Set Screw X 4
Radio Tray
Landing Gear Skid
Landing Gear Struts
M3X5 Set Screw
Frame Set Pre assembled-
A
B
Skid Cap
M3x5 Set Screw
M3x10 Self
Tapping Bolt
M3x10 Self
Tapping Bolt
0
10
20
30
40
2
Engine & Pinion
Use Threadlock
M3X10 Cap Head Bolt
Engine Nut
Engine Mount
Crank Case Holder
Factory
Clutch
Assembled
Head Bolt
M3X12 Cap
Engine Thrust Washer
M3 Nylon Nut x2
M3x14 Cap Head Bolt x2
M3x8 Cap Head Bolt x2
M3x10 Cap Head Bolt x10
Lock the Piston in place with a
Crank Shaft Locking Tool in
order to tighten the Engine Nut.
See Page Team Tips!
Crank Case Dampner
Wrench
M3x12 Cap Head Bolt x2
M3x16 Cap Head Bolt x4
Page 7
Leave a slight gap between the
clutch and clutch bell so that
the engine may run smoothly.
Clutch Bell
Clutch
0.2~0.5mm
gap here
0
10
20
30
40
3
Boom & Tail Rotor
Crimping Belt damages the Tensile Cords
and will result in premature failure.
Be careful not to over tighten the
Bolts when attaching the Tail Rotor
Blades. The Tail Blades should be
able to move with a slight amount
of resistance within the Tail Blade
Holders.
Bearing Retainer
Use Threadlock
Insert the Tail Boom
fully into the Tail Case
before tightening the
2.5x6mm Bolts.
These bolts are used only
to compress the boom.
Please do not screw them
in completely.
M3 Nylon Nut
M3 Washer
M3 Nylon Nut
M3 Nylon Nut
M3 Washer
M3x14 Cap
Head Bolt
M2.5x6 Cap
Head Bolt
M3x26 Cap
Head Bolt
M3x32 Cap
Head Bolt
M3x38 Cap Head Bolt x4
M3 Washer x4
M3 Nylon Lock Nut x10
M2.5x6 Cap Head Bolt x2
M3x14 Cap Head Bolt x2
M3x26 Cap Head Bolt x2
M2.5 x8 Self Tapping
Bolt X 4
M3x32 Cap Head Bolt x2
M3x25 Cap Head Bolt x2
See Page Team Tips!
Bottom Board
M3 Nylon Nut
M3x14 Cap
Head Bolt
M3x16 Cap
Head Bolt
M3x8 Cap
Head Bolt
Page 8
Slide the tail boom through the
tail boom block. Twist the tail belt
90° to the right before inserting it
into the boom block and through
the idler pulleys.
M2.5x8 Self Tapping Bolt
M3 Nylon Nut
0
10
20
30
40
Main Gear
4
M3x38 Cap
Head Bolt
M3x25 Cap
Head Bolt
There are 2 grooves on the boom. The
shorter groove is towards the tail while
the longer one is towards the frame.
Use Threadlock
Lift the Main Shaft Collar upwards and
secure to the Main Shaft by slightly
tightening the Lock Screw. It is
necessary to align the Lock Screw
through the hole in the side of the Main
Frame. While securing the Lock Screw,
make sure that you are pushing down
on the Main Shaft so that there will be
no up/down play in the Main Shaft once
the collar is secured.
M3 Nylon Lock Nut x1
M2.5x10 Cap Head Bolt x1
M3x27 Shanked Bolt x1
Mast Collar
M2.5x10 Cap
Head Bolt
Apply this Hole
See Page Team Tips!
Check the correct rotation of the
Tail Rotor Blades. The Blade on
the Top moves to the rear. If t he
Tail Rotor rotates incorrectly,
simply pull out the main shaft and
twist the Belt in the other
direction.
Tail Blade
Turn Direction
M3 Nylon Nut
M3x27 Shanked Bolt
Page 9
Thread
Flybar
Thread
Thread
Paddle Insert
0
10
20
30
40
5
Rotor,Washout & Swashplate
Be sure to note the correct
direction of the Flybar Paddles
as shown in the diagram. It is
very important to insure that the
Paddles are in parallel to each
other, as well as to the Flybar
Control Arm Assembly.
In this step, push the Flybar through
the Flybar Collar, Flybar Holder, and
Flybar ControlArm. Using set screws,
fix theArms and Collars onto the
Flybar. Make sure that both sides of the
Flybar are of equal lengths.
M3x4
Set Screw
Adjust so that each side has exactly the same length
M4x4
Set Screw
M3x22 Shanked Bolt x1
M2.5 x8 Self Tapping
Bolt X 4
M4x4 Set Screw x2
Use Threadlock
M2.5 x8 Self Tapping
Bolt X 2
M3 Nylon Lock Nut x1
M3x4 Set Screw x6
Washout Set
Swashplate
M3X4 Set Screw
Paddle
Main Shaft
M3x22 Cap
Head Bolt
M3 Nylon
Nut
M2.5x8 Self
Tapping Bolt
M3X4 Set Screw
See Page Team Tips!
Page 10
M2.5x16 Self Tapping
Bolt X 4
2.5mm Washer X 20
Servo Nut x 10
M2x6 Cap Head Bolt x8
M2.5x20 Cap Head Bolt x16
11mm
All control balls should be set
to 11mm from the center.
0
10
20
30
40
6
Servo
Head Bolt
Servo Spacer
Nylon Servo Nut
M2 5X20 Cap.
Servo
Link Ball
Servo Horn
Tapping Bolt
2 5mm Washer.
M2 5X16 Self.
M2X6 Cap
Head Bolt
Servo Horn
Page 11
8
Equipment illustration
Main Grip
Washout Arm
Phasing Control Ring
Boom
Parallel to
the Boom
To get the right phasing adjustment,
turn the Phasing Control Ring until
the Washout Arms and Main Grips
are parallel to the Tail Boom.
Battery
Aileron
Elevator
Throttle
Rudder
Pitch
Hitec/Futaba
JR
Ch1
Ch2
Ch3
Gyro Gain Ch5
Ch4
Ch6
Ch2
Ch3
Ch1
Aux2
Ch4
Aux1
Gyro
Please check first your radio manuals before connecting these electronic devices as shown below.
Receiver
7
Phasing Control Ring Adjustment
Main Grips
Washout Arm
Boom
Phasing Block
0
10
20
30
40
0
10
20
30
40
Receiver
Pitch Servo
Rudder Servo
Throttle Servo
Aileron Servo
Elevator Servo
Gyro
Battery
Page 12
00
10
20
30
40
00
9
Linkage
The Linkage lengths indicated below are approximate. Be aware that these values may vary depending on
the servos and arms used in your setup.
Compass Model Ball Links are designed to
be tight; this allows you to adjust them to
your personal needs. We highly suggest the
use of a ball link sizing tool.
25mmx2
2mm
Please cut away 1.5mm
from each Ball Link.
41mmx2
60mmx2
107mmx2
40mmx3
75.5mmx1
144mmx4
Rudder Servo
300mmx1
Carbon Tube
Do not used pliers to resize Ball Links. Pliers can
cause inadvertent damage to the Ball Links that may
result in failure during use.
Page 13
00
10
20
30
40
00
10
Setup
Pitch
General Flight
Throttle Pitch
5
100%
13 deg
4
85%
3
70%
4~5 deg
2
35%
1
0%
-5 deg
3D Style
Throttle Pitch
5
100%
13 deg
4
75%
6.5 deg
3
50%
0 deg
2
75%
-6.5 deg
1
100%
-13 deg
0%
20%
40%
60%
80%
100%
12345
0%
20%
40%
60%
80%
100%
12345
Throttle Curve
JR Futaba
Swash Type SWH
S3 120 SR3
Aile Elev Pitch
50% 50% 50%
Swash Type Setting
For any radio setup please refer to your radio
instructions first.
The data's shown above provide some general suggestions
for radio setting. This information varies according to types
of main blades, motor, pinion gear and engine.Adjustment
has to be made during the actual flight.
A
Parallel
Make sure that the Flybar Control Arms and Paddles are in line as shown in the diagram.
Turn on the Transmitter, set the Throttle Stick into center position for 0 ° Pitch. Use the Subtrim menu to
adjust the 3 Swash ServoArms to reach the angle shown above.The 2 Push pull link rods are not
necessarily parallel but must be the same length
-
,.
B
9
0
°
9
0
°
T Arm
I Arm
Aileron Servo
Elevator Servo
Swashplate
Swashplate
Page 14
By adjusting the Links between Swashplate and Mixing Arms set the Mixing Arms to a 5° downward position.
Adjust the Links between the Mixing Arms and the Main Blade Holder to set the Main Blade Pitch to 0°.
D
Level the Swashplate by adjusting the links from the Servo Arms to the Swashplate. Use a Compass
Swashplate Tool as guide. Then set level the WashoutArms.
C
Horizontal
Horizontal
06 0501 Swashplate Tool-
Swashplate
Washout Arm
At the low throttle stick and throttle trim, the carburetor hole should be completely close.At full throttle stick,
carburetor hole should be completely open. Adjust the ATV in radio, or/and the control horn position on the
engine to achieve above requirement. Make sure the servo does not bind at any traveling point.
E
Full
open
Full
close
Full
Throttle
Lowest
Throttle
At Rudder middle stick set Rudder Servo 90 degree to the Carbon Tube Link, the RudderArm 90° to the
Carbon Tube Link And set Tail Blade to 7 pitch
,
.°.
7°
9
0
°
Rudder Servo
Carbon Tube
Rudder Arm
F
0 Pitch°
Mixing Arm
5
°
Page 15
Aileron Check
Mod 1
Mod 2
Elevator Check
Rudder Check
Pitch Check
Swashplate Reaction
00
10
20
30
40
00
11
Servo Direction Check
Turn the Transmitter on, your position has to be right behind the helicopters Tail. Make sure that the Swashplate
Mode is set to CCPM 120°. Move the Sticks according to the drawings and check the reaction of the Swashplate
and the Tail Pitch Plate. Check your Throttle setting as well and adjust your Transmitter settings accordingly.
Tilt Left
Tilt Right
Tail Pitch Plate
Slide left
Slide Right
Tilt For ward
Tilt Backward
Swash Plate
Ascent
Descent
Page 16
M2.5x6 Self
Tapping Bolt
Canopy Insert
Use AB Glue
A
B
M2.5x6 Self Tapping
Bolt X 2
A
B
ABA
B
00
10
20
30
40
00
12
Canopy
00
10
20
30
40
00
13
Rotor Direction
5. Check that main blades, paddles and tail blades are installed in the right direction.
6. Check that there are no missing or damaged parts, never fly with any damaged parts.
7. Make sure all electronic devices are firmly fastened and connected.
8. Before starting the engine, make sure the Flight Mode or Idle switch is in Normal mode,
1. Ensure that receiver & transmitter battery are fully charged.
2 Check if all bolts and screws are fastened tightly and correctly..
3 Repeat step 11 to check all servo functions are correct..
4 Ensure tail and gyro direction are correctly set..
00
10
20
30
40
00
14
Pre Flight Check
Place the Canopy onto the Frames and mark
the right position of the Canopy Inserts. Apply
AB Glue to fix the Canopy Insert onto the
Canopy.
When the Rotor spins clockwise the Tail Blades should turn
clockwise as well watching the Tail Rotor from the Tail Fin side.
If not Belt is installed the wrong way and has to be corrected.
M3x15 Cap Head Bolt x2
and that the Throttle stick be in the lowest position.
Head Bolt
M3X12 Cap
Canopy
Dampener
Thumb Screw
Page 17
Team Tips
General:
1.
2.
3.
The Ball Links on the 3D Plus need to be resized. These Ball Links will NOT break in over time.
they will stay tight and will cause unwanted interactions.
It is very important to make sure the clunk line does not get hung up inside to fuel tank. Remove the
fuel tank from the helicopter and rotate the tank. Be sure the clunk can get close to all corners of the
tank.
For tail servos like the 8900G, you have to file the mount a little bit wider to fit the servo.
Main Grip
Thrust Bearing Direction
Main grips are factory preassembled, in
case of reassembling, be sure to note
correct placement of large/small I.D.
washers during assembly.
Apply Grease Here
Larger ID
(IN)
Smaller ID
(OUT)
Some pilots may want to mount the gyro under the canopy
on the front electronics tray. To do so, mount the
electronics tray upside down, by doing so will allow the
gyro to be mounted perpendicular to the main shaft and
also allow more clearance for the receiver battery.
Step 3
Step 4
Step 5
:
:
:
Leave About 0.1mm space between the Flybar Collar and the Flybar Holder, this avoids the Flybar to snap
when flying.
It is very important to resize the Ball Links for smooth travel, especially on the tail; because issues like tail
wag, sluggish tail, or inconsistent Piro-rate will occur.
It is vital not to over tighten the Main Gear Bolt, or it can cause the Autorotation Gear to slightly warp. This
can cause a premature Belt failure, or reduce the lifetime of the Belt.
Page 18
COMPASS MODEL (HK) LIMITED
www.compassmodel.com
Page 19
Parts List
3D Plus
Version 1.0/2009
How to order your parts!
1. Check part number on the drawing
2. Use the part number to find the ORDER number on the list
3. Only use ORDER number for your parts order
Copyright @Compass Model 2009
As we continue to improve our products, this part list may not reflect all recent product amendments.
For more information, please refer to www.compassmodel.com
Page 20
79 0308-
80 0206S-
02 1538-
80 0322S-
02 1103-
02 0110-
63 8165-
91 0003-
80 0428-
82 821003-
02 0701-
60 8165-
60 8165-
61 4083-
02 0118-
82 5131-
91 0004-
02 0113-
02 0109-
97 0920-
07 0106-
80 0310-
79 0510-
02 0507-
82 2562-
02 0511-
81 0304-
02 0543-
81 0304-
60 3083-
02 0553S-
02 0539-
02 0540-
02 0701-
02 0536G-
80 0206S-
80 0206S-
80 2514-
02 0531-
60 4083-
81 0404-
80 0208S-
60 4083-
Main Grip
Apply Grease Here
Larger ID
(IN)
Smaller ID
(OUT)
Thrust Bearing Direction
Main grips are factory preassembled, in
case of reassembling, be sure to note
correct placement of large/small I.D.
washers during assembly.
Page 21
Part No. Part Description Order No. Order Description Qty,
02-0109 Delrin Dampener 8m
m
02-0109
Delrin Dampeners 8m
m
2 pcs/ba
g
02-0110 Spindle Washer 8mm
02-0110
Spindle Washers 8mm 2 pcs/ba
g
02-0113 Spindle Shaft 8m
m
02-0113
Spindle Shafts 8m
m
2 pcs/ba
g
02-0118 Flybar Colla
r
02-0118
Flybar Collars 2 pcs/ba
g
02-0507 Mixing Arm
02-0507
Mixing Arm se
t
2 pcs/ba
g
02-0511 Paddle Insert
02-0553S
Paddle se
t
2 pcs/ba
g
02-0531 Mixing Arm Bushin
g
02-0531S
Bushing set (3 sizes
)
6 pcs/ba
g
02-0536G Flybar Holder
02-0536G
Flybar Holder w; Bearings1
p
cs/ba
g
02-0539 Flybar Colla
r
02-0539
Flybar Collars 2 pcs/ba
g
02-0540 Flybar Control Arm
02-0540s
Flybar Control Arm se
t
2 pcs/ba
g
02-0543 Flyba
r
02-0543
Flybars 2 pcs/ba
g
02-0553 Paddle
02-0553S
Paddle se
t
2 pcs/ba
g
02-0701 Stainless Link Ball
02-0701
Stainless Link Balls 10 pcs/ba
g
02-1103 Main Blade Holder 8m
m
02-1103
Main Blade Holder set 8m
m
2 pcs/ba
g
02-1538 Control Ball Space
r
02-1538
Control Ball Spacer set 2 pcs/ba
g
07-0106 Rotor Hub
07-0106
Rotor Hub set 1 set/ba
g
60-3083 Ball Bearing 3x8x3
60-3083
Ball Bearings 3x8x3 5 pcs/ba
g
60-4083 Ball Bearing 4x8x3
60-4083
Ball Bearings 4x8x3 5 pcs/ba
g
60-8165
Ball Bearin
g
8x16x5
60-8165
Ball Bearings 8x16x5
2
p
cs/ba
g
61-4083 Flanged Bearing 4x8x3
61-4083
Flanged Bearings 4x8x3 5 pcs/ba
g
63-8165 Thrust Bearing 8x16x5
63-8165
Thrust Bearings 8x16x5 2 set/ba
g
79-0308 Button Head Bolt M3×8
79-0308
Button Head Bolts M3×8 10 pcs/ba
g
79-0510 Button Head Bolt M5x10
79-0510
Button Head Bolts M5x10 10 pcs/ba
g
80-0206S Cap Head Bolt M2x6
80-0206S
Cap Head Bolts M2x6 10 pcs/ba
g
80-0208S Cap Head Bolt M2x8
80-0208s
Cap Head Bolt M2x8 10 pcs/ba
g
80-0310 Cap Head Bolt M3x10
80-0310
Cap Head Bolts M3x10 10 pcs/ba
g
80-0322S
Shanked Bolt M3x22
80-0322S
Shanked Bolts M3x22
2
p
cs/ba
g
80-0428 Shanked Bolt M4×28
80-0428
Shanked Bolts M4×28 2 pcs/ba
g
80-2514 Cap Head Bolt M2.5×14
80-2514
Cap Head Bolts M2.5×14 10 pcs/ba
g
81-0304 Set Screw M3x4
81-0304
Set Screws M3x4 10 pcs/ba
g
81-0404 Set Screw M4x4
81-0404
Set Screws M4x4 10 pcs/ba
g
82-2562 Washer 2.6x5.2x0.3
82-2562
Washers 2.6x5.2x0.3 10 pcs/ba
g
82-5131 Washer 5.3×13×1
82-5131
Washers 5.3×13×1 10 pcs/ba
g
82-821003 Washer 8.2×10×0.3
82-821003
Washers 8.2×10×0.3 2 pcs/ba
g
91-0003
Ny
lon Lock Nut M3
91-0003
Ny
lon Lock Nuts M3
10
p
cs/ba
g
91-0004
Ny
lon Lock Nut M4
91-0004
Ny
lon Lock Nuts M4 10 pcs/ba
g
97-0920 Rubber O-Ring 13×9×2
97-0920
Rubber O-Ring set 13×9×2 4 pcs/ba
g
Page 22
02 0264A-
02 0264B-
02 0250-
80 0208S-
91 0003-
91 0003-
60 3092-
80 0314-
80 0208-
82 3402-
63 4094-
60 4094-
02 0209-
81 0305-
02 0701-
90 0201-
80 2506-
80 2506-
02 0229-
98 1800B-
02 0214-
02 0262-
05 0227-
05 0231-
61 5134-
82 5808-
82 5804-
61 5134-
06 0213-
60 7113-
02-0205
80 2508-
02 0230-
02 0213-
05 0229-
06 0208-
02 1211-
02 0225-
60 7113-
06 0222-
02-8205
02-8206
05-0227Z
06 0213S-
Page 23
Part No. Part Description Order No. Order Description Qty,
02-0205 Tail Blade Link
02-0205S
Tail Blade Links w, Pin 2 pcs/ba
g
02-0209 Tail Rotor Hu
b
02-0209
Tail Rotor Hu
b
1 pcs/ba
g
02-0213 Tail Pitch Slider
02-0213
Tail Pitch Slider 1 pcs/ba
g
02-0214 Tail Shaft
02-0214
Tail Shafts 2 pcs/ba
g
02-0225 Grooved Pi
n
02-0205S
Provided w, 02-0205S
02-0229 Gear box frame
02-0229
Z
Gear box frame w, B
B
1 set/ba
g
02-0230 Tail hinge
02-0230S
Tail Hing with Pin 1 set/ba
g
02-0250 Tail Blade
02-0250
Tail Blade set 2 pcs/ba
g
02-0262 Tail rotor pulle
y
02-0262S
Tail rotor pulley with spring pin 1 pcs/ba
g
02-0264AB Tail blade holder
02-0264AB
Tail blade holder 2 pcs/ba
g
02-0701 Stainless Link Ball
02-0701
Stainless Link Balls 10 pcs/ba
g
02-1211 Tail pitch plate w, BB
02-1211
Tail pitch plate w, BB 1 pcs/ba
g
02-8205 Tail Pitch Control unit
02-8205
Tail Pitch Control unit 1 set/ba
g
02-8206 Tail Case Set
02-8206
Tail Case Set 1 set/ba
g
05-0227 Gear box se
t
05-8227
Z
Gear box se
t
1 set/ba
g
05-0229 Tail pitch slider
05-0229S
Tail Pitch Slider w. BB 1 pcs/ba
g
05-0231 Gear Box Membe
r
05-0231
Gear Box Membe
r
2 pcs/ba
g
06-0208 Tail pitch arm
06-0213S
Tail pitch arm w, H-arm & Pin 1 set/ba
g
06-0213 Tail pitch H arm
06-0213S
Tail pitch arm w, H-arm & Pin 1 set/ba
g
06-0222
Guide Pin Bol
t
06-0222
Guide Pin Bolts
2
p
cs/ba
g
60-3092 Ball Bearing 3x9x2.5
60-3092
Ball Bearings 3x9x2.5 4 pcs/ba
g
60-4094 Ball Bearing 4x9x4
60-4094
Ball Bearings 4x9x4 5 pcs/ba
g
60-7113 Ball Bearing 7x11x3
60-7113
Ball Bearings 7x11x3 2 pcs/ba
g
61-5134 Flanged Bearing 5x13x4
61-5134
Flanged Bearings 5x13x4 2 pcs/ba
g
63-4094 Thrust Bearing 4x9x4
63-4094
Thrust Bearings 4x9x4 2 pcs/ba
g
80-0208
Cap Head Bolt M2x8
80-0208
Cap Head Bolts M2x8 10 pcs/ba
g
80-0208S Cap Head Bolt M2x8
80-0208S
Cap Head Bolts M2x8 10 pcs/ba
g
80-0314
Cap head Bolt M3x14
80-0314
Cap head Bolts M3x14
10
p
cs/ba
g
80-2506
Cap Head Bolt M2.5x6
80-2506
Cap Head Bolts M2.5x6 10 pcs/ba
g
80-2508
Cap Head Bolt M2.5x8
80-2508
Cap Head Bolts M2.5x8 10 pcs/ba
g
81-0305
Set Scre
w
81-0305
Set Scre
w
10 pcs/ba
g
82-3402
Washer 3.2x5.2x0.3
82-3402
Washer 3.2x5.2x0.3 10 pcs/ba
g
82-5804
Washer 5x8x0.4
82-5804
Washer 5x8x0.4 10 pcs/ba
g
82-5808
Washer 5x8x0.8
82-5808
Washer 5x8x0.8 10 pcs/ba
g
90-0201
Hexagonal nut2x1
90-0201
Hexagonal nut2x1 10 pcs/ba
g
91-0003
Ny
lon Lock Nut M3
91-0003
Ny
lon Lock Nuts M3 10 pcs/ba
g
98-1800B
Tail belt 3M1800 Bando
98-1800B
Tail belt 3M1800 Bando 1 pcs/ba
g
Page 24
02 0318G-
07 4302-
02 0321-
02 0307-
81 0406-
79 0308-
60 6196-
80 0306-
80 0312-
60 10195-
02 0325-
02 0304-
02 0302-
02 0326-
02 0312-
60 6124-
62 101412-
61 2562-
07 0621-
07 4603-
02 0601-
07 0623-
02 0519G-
02 0503G-
80 2505-
02 0535-
79 0306-
02 0518-
80 2514-
02 0532-
60 4083-
62 121816-
07 0622-
05 0606-
80 2510-
80 0327-
60 12215-
60 12215-
79 0308-
07 4501-
07 8410-
91 0003-
80 0310-
02 0332-
02 0309-
(02 0334YS)-
80 0316-
02 0334OS-
80 0308-
80 0206S-
06-0410S
80 0206S-
02-0313S
02-0311
Page 25
Part No. Part Description Order No Order Description Qty,
02-0302 Cooling Fan Hub
02-0302
Cooling Fan Hub 1 pcs/ba
g
02-0304 Cooling Fan
02-0304
Cooling Fan 1 pcs/ba
g
02-0307 Starter Couplin
g
02-0307S
Starter Couplin
g
1 pcs/ba
g
02-0309 Crank Case Holder
02-0309
Crank Case Holder 1 pcs/ba
g
02-0311 Engine Dampener
02-0311
Engine Dampener set 2 pcs/ba
g
02-0312 Clutch Liner
02-0312
Clutch Liner 1 pcs/ba
g
02-0313S Engine Mount Set
02-0313S
Engine Mount Set 1 set/ba
g
02-0318G Starter Bearing Block
02-0318G
Starter Bearing Block 1 pcs/ba
g
02-0321 Clutch Bell
02-0321
Z
Clutch Bell set 1 set/ba
g
02-0325 Clutch
02-0325
Z
Clutch set 1 pcs/ba
g
02-0326 Start Shaft
02-0326
Start Shaft set 1 pcs/ba
g
02-0332 Engine Mount Base
02-0332
Engine Mount Base 1 pcs/ba
g
02-0334OS Crank Case Dampener OS
02-0334OS
Crank Case Dampener OS 1 pcs/ba
g
02-0334YS Crank Case Dampener YS
02-0334YS
Crank Case Dampener YS 1 pcs/ba
g
02-0503G Washout Base (gre
y)
02-0503G
Washout Base (gre
y)
1pcs/ba
g
02-0518 Washout Link
02-0518
Washout Links 2 pcs/ba
g
02-0519G Phasing Control Rin
g
(grey)
02-0519G
Phasing Control Ring (gre
y)
1 pcs/ba
g
02-0532 Bushin
g
02-0531S
Bushing set (3 sizes
)
6 pcs/ba
g
02-0535 Washout Control Arm
02-0535
Washout Control Arm set 2 pcs/ba
g
02-0601
Main Shaft
02-0601
Main Shaft
1
p
cs/ba
g
05-0606 Main Shaft Lock Clamp (Ø
05-0606S
Main Shaft Lock Clamp set (Ø 10mm
)
1pcs/ba
g
06-0410S Swashplate Pin
06-0410S
Swashplate Pin Set 1 set/ba
g
07-0621 Autorotation Hu
b
07-0621
Z
Autorotation Hub w, One Way Bearin
g
1 pcs/ba
g
07-0622 Autorotation Sleev
e
07-0622
Autorotation Sleev
e
1 pcs/ba
g
07-0623 Main Pulley Hu
b
07-0623
Main Pulley Hu
b
1 pcs/ba
g
07-4302 Drive gear
07-4302
Drive gear 1 pcs/ba
g
07-4501
Main Pulle
y
07-4501
Main Pulley
1
p
cs/ba
g
07-4603 Main Gear Molded
07-4603
Main Gear Molded 1 pcs/ba
g
07-8410 Swashplate
07-8410
Swashplate 1 set/ba
g
60-10195 Ball Bearing 10x19x5
60-10195
Ball Bearing 10x19x5 4 pcs/ba
g
60-12215 Ball Bearing 12x21x5
60-12215
Ball Bearings 12x21x5 2 pcs/ba
g
60-4083 Ball Bearing 4x8x3
60-4083
Ball Bearings 4x8x3 5 pcs/ba
g
60-6124 Ball Bearing 6x12x4
60-6124
Ball Bearings 6x12x4 2 pcs/ba
g
60-6196 Ball Bearing 6x19x6
60-6196
Ball Bearings 6x19x6 2 pcs/ba
g
61-2562 Flanged Bearing 2.5x6x2.6
61-2562
Flanged Bearings 2.5x6x2.6 10 pcs/ba
g
62-101412
One Wa
y
Bearing 10x14x12
62-101412
One Way Bearing 10x14x12
1 set/ba
g
62-121816 One Way Bearing 12x18x16
62-121816
One Way Bearing 12x18x16 1 pcs/ba
g
79-0306 Button Head Bolt M3x
6
79-0306
Button Head Bolts M3x
6
10 pcs/ba
g
79-0308
Button Head Bolt M3x8
79-0308
Button Head Bolts M3x
8
10 pcs/ba
g
80-0206S Cap Head Bolt M2x6
80-0206S
Cap Head Bolts M2x
6
10 pcs/ba
g
80-0306 Cap Head Bolt M3x6
80-0306
Cap Head Bolts M3x
6
10 pcs/ba
g
80-0308 Cap Head Bolt M3x8
80-0308
Cap Head Bolts M3x8 10 pcs/ba
g
80-0310 Cap Head Bolt M3x10
80-0310
Cap Head Bolts M3x1
0
10 pcs/ba
g
80-0316 Cap Head Bolt M3x12
80-0316
Cap Head Bolts M3x1
2
10 pcs/ba
g
80-0327 Shanked Bolt M3x27
80-0327
Shanked Bolts M3x27 2 pcs/ba
g
80-2505 Button Head Bolt M2.5X5
80-2505
Button Head Bolts M2.5X5 10 pcs/ba
g
80-2514
Cap Head Bolt M2.5x15
80-2514
Cap Head Bolts M2.5x15
10
p
cs/ba
g
81-0406 Set Screw M4x
6
81-0406
Set Screws M4x
6
10 pcs/ba
g
91-0003
Ny
lon Lock Nut M3
91-0003
Ny
lon Lock Nuts M3 10 pcs/ba
g
Page 26
a:95-0310
b:80-0306
d:81-0316
07 0907-
02 0848-
95 2508-
80 0325-
07 0835-
02 0805-
02 0804-
02 0847-
02 1843-
02 0846-
60 10195-
02 0845-
02 1825-
91 0003-
02 0605G-
02 0841-
02 0849-
02 0831-
02 0815-
80 0310-
a
a
a
a
a
a
a
a
a
a
a
a
a
b
b
b
b
b
b
b
b
c:80-0338
c
c
c
c
d
b
e
e
e:95-2508
79 0308-
02 8811-
02 5811-
02 5811-
07 0820-
02 4811-
07 8811-
07 0806-
60 3095-
80 0312-
05 0805-
07 8302-
02 0827-
02 0604-
02 0604-
78 0308-
91 0003-
02 1805-
02 0606-
02 0306-
79 0306-
02 1805-
02 1833-
79 0308-
02 1802-
80 0308-
81 0305-
91 0003-
80 0314-
02 0820-
02 0821-
02 0822-
Page 27
Part No. Part Description Order No. Order Description Qty,
02-0306 Cooling fan shroud (3D Plus
)
02-0306
Cooling fan shroud (3D Plus
)
1 pcs/ba
g
02-0604 Bearing block lowe
r
02-0604
Z
Bearing block lower se
t
1 pcs/ba
g
02-0605G Bearing block uppe
r
02-0605G
Bearing block upper se
t
1 pcs/ba
g
02-0606 Fan Shroud Mount
02-0606
Fan Shroud Mount set 1 pcs/ba
g
02-0804 Frame Spacer 13.5mm
02-0804
Frame Spacer set 13.5mm 4 pcs/ba
g
02-0805 Cross Member M3x30
02-0805
Cross Member set M3x30 5 pcs/ba
g
02-0815 Battery Tray (3Dplus
)
02-0815
Battery Tray (3Dplus
)
1 pcs/ba
g
02-0820 Skid End Ca
p
02-0820
Skid End Cap set 4 pcs/ba
g
02-0821 Landing Gear Skid
02-0821
Landing Gear Skids w. Caps2
p
cs/ba
g
02-0822 Landing Gear Strut (3D Plus
)
02-0822
Landing Gear Struts (3D Plus
)
2 pcs/ba
g
02-0827 Tank Mount
02-0827
Tank Mount set 2 pcs/ba
g
02-0831 Main Frame
02-0831
Main Frame set 2 pcs/ba
g
02-0841 Canopy Standof
f
02-0841S
Canopy Standoff se
t
4 pcs/ba
g
02-0845 Frame Membe
r
02-0845S
Frame Member se
t
4 pcs/ba
g
02-0846
Tank Dampener
02-0846
Tank Dampener set
8
p
cs/ba
g
02-0847 Frame Membe
r
02-0845S
Frame Member se
t
4 pcs/ba
g
02-0848 Frame Membe
r
02-0845S
Frame Member se
t
4 pcs/ba
g
02-0849 Frame Membe
r
02-0845S
Frame Member se
t
4 pcs/ba
g
02-1802 Bottom Frame Stiffene
r
02-1802
Bottom Frame Stiffene
r
1 pcs/ba
g
02-1805 Cross Member Mount M3x30
02-1805
Cross Member Mount set M3x30 2 pcs/ba
g
02-1825 Tail Boom Moun
t
02-1825s
Tail Boom Mount se
t
1 set/ba
g
02-1833 Back Frame Stiffene
r
02-1833
Back Frame Stiffene
r
1 pcs/ba
g
02-1843 Gyro Tray plastic
02-1843
Gyro Tray plastic 1 pcs/ba
g
02-4811 Tank Ca
p
02-4811
Tank Ca
p
1 pcs/ba
g
02-5811
N
ozzle
02-5811
N
ozzle 1 pcs/ba
g
02-8811 Fuel Tank Assembl
y
02-8811
Fuel Tank Assembl
y
1 set/ba
g
05-0805
Guide Pulle
y
05-0805
Z
Guide Pulley se
t
2 pcs/ba
g
07-0806 Guide Pulley Moun
t
07-0806
Guide Pulley Moun
t
1 pcs/ba
g
07-0820 Tank Cap Connector
07-0820
Tank Cap Connector 1 pcs/ba
g
07-0835 Frame Membe
r
07-0835
Frame Membe
r
1 pcs/ba
g
07-0907 Swashplate Guide
07-0907
Swashplate Guide 1 pcs/ba
g
07-8302 Guide Pulley se
t
07-8302
Guide Pulley Se
t
1 set/ba
g
07-8811 Tank Fitting (3D Plus
)
07-8811
Tank Fitting set (3D Plus
)
1 set/ba
g
60-10195 Ball Bearings 10x19x5
60-10195
Ball Bearings 10x19x5 4 pcs/ba
g
60-3095 Ball Bearing 3x9x5
60-3095
Ball Bearings 3x9x5 2 pcs/ba
g
78-0308
Flat Head Bolt M3x8
78-0308
Flat Head Bolts M3x8
10
p
cs/ba
g
79-0306 Button Head Bolt M3x
6
79-0306
Button Head Bolts M3x
6
10 pcs/ba
g
79-0308 Button Head Bolt M3x8
79-0308
Button Head Bolts M3x
8
10 pcs/ba
g
80-0306
Cap Head Bolt M3x6
80-0306
Cap Head Bolts M3x
6
10 pcs/ba
g
80-0308 Cap Head Bolt M3x6
80-0308
Cap Head Bolts M3x8 10 pcs/ba
g
80-0310 Cap Head Bolt M3x10
80-0310
Cap Head Bolts M3x1
0
10 pcs/ba
g
80-0312 Cap Head Bolt M3x12
80-0312
Cap Head Bolts M3x1
2
10 pcs/ba
g
80-0314 Cap Head Bolt M3x1
4
80-0314
Cap Head Bolts M3x1
4
10 pcs/ba
g
80-0325 Cap Head Bolt M3x25
80-0325
Cap Head Bolts M3x25 10 pcs/ba
g
80-0338 Cap Head Bolt M3x38
80-0338
Cap Head Bolts M3x38 10 pcs/ba
g
81-0305 Set Screw M3x5
81-0305
Set Screws M3x5 10 pcs/ba
g
81-0316 Set Screw M3x1
6
81-0316
Set Screws M3x1
6
10 pcs/ba
g
91-0003
Ny
lon Lock Nut M3
91-0003
Ny
lon Lock Nuts M3
10
p
cs/ba
g
95-0310 Self Tapping Bolt 3x10
95-0310
Self Tapping Bolts 3x10 10 pcs/ba
g
95-2508 Self Tapping Bolt 2.5x8
95-2508
Self Tapping Bolts 2.5x8 10 pcs/ba
g
Page 28
02 0816T-
82 3201-
02 0826-
02 0823B-
02 0823A-
91 0003-
02 0813-
80 2508-
05 0825T-
82 3201-
80 0326-
80 0332-
40 2660-
95 2508-
02 0709-
02-0814S
02 0853-
02 0810-
02 0850P-
(02-0850)
06 0851-
02 0818-
Page 29
Part No. Part Descriptio
n
Order No. Order Descriptio
n
Qty,
02-0709 Ball Link
02-0709
Ball Links 10 pcs/ba
g
02-0810S
G
Thumb Screw (gold
)
02-0810SG
Thumb Screw set (gold
)
4 pcs/ba
g
02-0813 Tail Boom Brace Connecto
r
02-0813S
Tail Boom Brace Connector se
t
4 pcs/ba
g
02-0814S Tail Boom Brace 530mm
02-0814S
Tail Boom Brace set 530m
m
2 pcs/ba
g
02-0816T Vertical Fin Carbon (3Dplus
)
02-0816T
Vertical Fin Carbon (3Dplus
)
1 pcs/ba
g
02-0818 Tail cControl Rod Guide Clam
p
02-0818S
Tail cControl Rod Guide Clamp set 4 pcs/ba
g
02-0823AB Tail Boom Support Clam
p
02-0823AB
Tail Boom Support Clam
p
1 set/ba
g
02-0826 Tail Boom 705mm
02-0826
Tail Boom 705mm 2 pcs/ba
g
02-0850 Fiberglass Canopy (3D Plus
)
02-0850
Fiberglass Canopy (3D Plus
)
1 pcs/ba
g
02-0850P Painted FG Canopy (3DPlus
)
02-0850
P
Painted FG Canopy (3D Plus
)
1 pcs/ba
g
02-0853 Canopy Rubber Gromme
t
02-0853
Canopy Rubber Grommet se
t
10 pcs/ba
g
05-0825T Horizontal Fin Carbon (3Dplus
)
05-0825T
Horizontal Fin Carbon (3Dplus
)
1 pcs/ba
g
06-0851 Canopy Insert
06-0851
Canopy Insert 1 set/ba
g
40-2660 Tail Control Rod 2X660
40-2660S
Tail Control Rod 2X660 1 pcs/ba
g
80-0326 Cap Head Bolt M3x26
80-0326
Cap Head Bolts M3x2
6
10 pcs/ba
g
80-0332 Cap Head Bolt M3x32
80-0332
Cap Head Bolts M3x3
2
10 pcs/ba
g
80-2508 Cap Head Bolt M2.5x8
80-2508
Cap Head Bolts M2.5x8 10 pcs/ba
g
82-3201 Washer 3.2x10x1.2
82-3201
Washers 3.2x10x1.2 10 pcs/ba
g
91-0003
Ny
lon Lock Nut M3
91-0003
Ny
lon Lock Nuts M3 10 pcs/ba
g
95-2508
Self Tappin
g
Bolt 2.5x8
95-2508
Self Tapping Bolts 2.5x8
10
p
cs/ba
g
Page 30
82 2578-
07-0202
40 2060-
07 0913-
40 2155-
40 2155-
02-0237S
40 2015-
40 2045-
40 2025-
07 0901-
07 0910-
07 0905-
02 0901-
95 2516-
02 0918-
07 0910S-
07 0912-
40 2025-
60 4083-
60 4083-
81-0404
80 0206S-
07-0911
81-0404
40-2095
83 0003-
07 0905-
Page 31
Part No. Part Description Order No. Order Description Qty,
02-0237 Carbon Tail Control Ro
d
02-0237S
Carbon Tail Control Rod se
t
1 set/ba
g
02-0901 Servo Spacer (3D Plus
)
02-0901
Servo Spacers (3D Plus
)
8 pcs/ba
g
02-0918 Servo Nut
02-0918
Servo Nuts 5 pcs/ba
g
07-0202 Tail Control Ar
m
07-0202S
Tail Control Arm se
t
1 set/ba
g
07-0901 Shaft Collar 10.6m
m
07-0910S
Provided w, 07-0910S
07-0905 Shaft Collar 2.5m
m
07-0910S
Provided w, 07-0910S
07-0910 Arm Shaf
t
07-0910S
Arm Shaft se
t
1 set/ba
g
07-0911 I-Arm
07-0911
I-Arm set 1 set/ba
g
07-0912 T-Leve
r
07-0912
T-Lever se
t
2 pcs/ba
g
07-0913 Elevator Arm
07-0913
Elevator Arm 1 pcs/ba
g
40-2015 Link Rod 15mm
E-LG-06
1 set/ba
g
40-2025 Link Rod 25mm
E-LG-06
1 set/ba
g
40-2045 Link Rod 45mm
E-LG-06
1 set/ba
g
40-2155 Link Rod 155mm
E-LG-06
1 set/ba
g
40-2060 Link Rod 60mm
E-LG-06
1 set/ba
g
40-2095 Link Rod 95mm
E-LG-06
1 set/ba
g
60-4083 Ball Bearing 4x8x3
60-4083
Ball Bearings 4x8x3 5 pcs/ba
g
80-0206S
Cap Head Bolt M2x6
80-0206S
Cap Head Bolts M2x
6
10 pcs/ba
g
81-0404 Set Screw M4x
4
81-0404
Set Screws M4x
4
10 pcs/ba
g
82-2578 Washer 2.7x7x0.8
82-2578
Washers 2.7x7x0.8 10 pcs/ba
g
83-0003 E-ring 3.1mm
82-2578
Washers 2.7x7x0.8 10 pcs/ba
g
95-2516 Self TappingBolt 2.5x16
95-2516
Self TappingBolts 2.5x16 10 pcs/ba
g
Link Rod set (3D Plus)
Special Thanks To:
John Lancaster
Dirk Everaert
Brian Tran
David Ketelhut
Devin LeBlanc
Jenkins Cortez
Page 32
COMPASS MODEL (HK) LIMITED
www.compassmodel.com
Loading...