Compal Electronics WM3B2100 User Manual
CL50
User Manual
Safety Instructions
Use the following safety guidelines to help protect yourself and
your computer.
When Using Your Computer
CAUTION: Do not operate your portable computer for
an extended period of time with the base resting directly
on your body. With extended operation, heat can
potentially build up in the base.
Allowing sustained contact with the skin could cause
discomfort or, eventually, a burn.
l Do not attempt to service the computer yourself. Always
follow installation instructions closely.
l Do not carry a battery in your pocket, purse, or other
container where metal objects (such as car keys) could
short-circuit the battery terminals. The resulting excessive
current flow can cause extremely high temperatures and may
result in damage from burns.
l Be sure that nothing rests on your AC adapter’s power cable
and that the cable is not located where it can be tripped over
or stepped on.
l Place the AC adapter in a ventilated area, such as a desktop or
on the floor, when you use it to run the computer or to charge
the battery. Do not cover the AC adapter with papers or other
items that will reduce cooling; also, do not use the AC
adapter while it is inside a carrying case.
l Do not push objects into air vents or openings of your
computer. Doing so can cause fire or electric shock by
shorting out interior components.
l Use only the AC adapter and batteries that are approved for
use with this computer. Use of another type of battery or AC
adapter may risk fire or explosion.
l Danger of explosion if battery is incorrectly replaced.
l Replace only with the same or equivalent type battery
recommended by the manufacturer.
l Dispose of used batteries according to the manufacturer’s
instructions.
l Before you connect the computer to a power source, ensure
that the voltage rating of the AC adapter matches that of the
available power source.
- 115 V/60 Hz in most of North and South America and some
Far Eastern countries such as South Korea and Taiwan.
- 100 V/50 Hz in eastern Japan and 100 V/60Hz in western
Japan.
- 230 V/50 Hz in most of Europe, the Middle East, and the Far
East.
l If you use an extension cable with your AC adapter, ensure
that the total ampere rating of the products plugged in to the
extension cable does not exceed the ampere rating of the
extension cable.
l To remove power from the computer, turn it off, remove the
battery, and disconnect the AC adapter from the electrical
outlet.
l To help avoid the potential hazard of electric shock, do not
connect or disconnect any cables or perform maintenance or
reconfiguration of this product during an electrical storm.
l Do not dispose of batteries in a fire. They may explode.
Check with local authorities for disposal instructions.
l When setting up the computer for work, place it on a level
surface.
l When traveling, do not check the computer as baggage. You
can put your computer through an X-ray security machine,
but never put your computer through a metal detector. If you
have the computer checked by hand, be sure to have a charged
battery available in case you are asked to turn on the
computer.
l When traveling with the hard drive removed from the
computer, wrap the drive in a non-conducting material, such
as cloth or paper. If you have the drive checked by hand, be
ready to install the drive in the computer. Your can put the
hard drive through an X-ray security machine, but never put
the drive through a metal detector.
l When traveling, do not place the computer in overhead
storage compartments where it could slide around. Do not
drop your computer or subject it to other mechanical shocks.
l Protect your computer, battery, and hard drive from
environmental hazards such as dirt, dust, food, liquids,
temperature extremes, and overexposure to sunlight.
l When you move your computer between environments with
very different temperature and/or humidity ranges,
condensation may form on or within the computer. To avoid
damaging the computer, allow sufficient time for the moisture
to evaporate before using the computer.
è NOTICE: When taking the computer from
low-temperature conditions into a warmer environment
or from high-temperature conditions into a cooler
environment, allow the computer to acclimate to room
temperature before turning on power.
l When you disconnect a cable, pull on its connector or on its
strain relief loop, not on the cable itself. As you pull out the
connector, keep it evenly aligned to avoid bending any
connector pins. Also, before you connect a cable make sure
both connectors are correctly oriented and aligned.
l Before you clean your computer, turn it off, unplug it from its
power source, and remove the battery.
l Handle components with care. Hold a component such as a
memory module by its edges, not its pins.
CAUTION: When using your telephone equipment,
basic safety precautions should always be followed to
reduce the risk of fire, electric shock and injury to
persons, including the following:
l Do not use this product near water, for example, near a
bathtub, washing bowl, kitchen sink or laundry tub, in a wet
basement or near a swimming pool.
l Avoid using a telephone (other than a cordless type) during an
electrical storm. There may be a remote risk of electric shock
from lightning.
l Do not use the telephone to report a gas leak in the vicinity of
the leak.
l Use only the power cord indicated in this manual.
Regulatory Notices
This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to Part 15 of the FCC
rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation.
Any changes or modifications made to this equipment may void
the user's authority to operate this equipment.
This equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio
communications. However, there is no guarantee that
interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by
one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and
receiver.
• Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician
for help.
• All external cables connecting to this basic unit must be
shielded. For cables connecting to PCMCIA cards, see the
option manual or installation instructions.
Federal Communications Commission (FCC)
PART 68 Warning
This equipment complies with Part 68 of the FCC Rules. On the
bottom of the computer is a label that contains, among other
information, the FCC Registration Number and Ringer
Equivalence Number (REN) for this equipment. You must, upon
request, provide this information to your telephone company.
FCC Part 68 Registration Number: 6CTTAI - 25876 - FB – E
REN: 0.8B
The REN is useful to determine the quantity of devices you may
connect to your telephone and still have those devices ring when
your number is called. In most, but not all areas, the sum of the
REN's of all devices should not exceed five (5.0). To be certain of
the number of devices you may connect to your line, as
determined by the REN, you should call your local telephone
company to determine the maximum REN for your calling area.
If your MODEM causes harm to the telephone network, the local
Telephone Company may discontinue your service temporarily.
If possible, they will notify you in advance. However, if advanced
notice isn't practical, you will be notified as soon as possible. You
will be informed of your right to file a complaint with the FCC.
Your telephone company may make changes in its facilities,
equipment, operations, or procedures that could affect the proper
functioning for your equipment. If they do, you will be notified in
advance to give you an opportunity to maintain uninterrupted
telephone service.
Federal Communications Commission (FCC) Statement
You are cautioned that changes or modifications not expressly
approved by the part responsible for compliance could void the
user’s authority to operate the equipment.
This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to part 15 of the FCC
rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in
a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the
following measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected.
-Consult the dealer or an experienced radio/TV technician for
help.
You are cautioned that changes or modifications not expressly
approved by the party responsible for compliance could void
your authority to operate the equipment.
FCC RF Radiation Exposure Statement:
This Transmitter must not be co-located or operating in
conjunction with any other antenna or transmitter.
CE Notice (European Union)
Marking by the symbol indicates compliance of this Compal
computer to the EMC Directive and the Low Voltage Directive of
the European Union. Such marking indicates that this Compal
system meets the following technical standards:
• EN 55022 — "Limits and Methods of Measurement of
Radio Interference Characteristics of Information
Technology Equipment."
• EN 55024 — "Information technology equipment -
Immunity characteristics - Limits and methods of
measurement."
• EN 61000-3-2 — "Electromagnetic compatibility (EMC) -
Part 3: Limits - Section 2: Limits for harmonic current
emissions (Equipment input current up to and including 16
A per phase)."
• EN 61000-3-3 — "Electromagnetic compatibility (EMC) -
Part 3: Limits - Section 3: Limitation of voltage
fluctuations and flicker in low-voltage supply systems for
equipment with rated current up to and including 16 A."
• EN 60950 — "Safety of Information Technology
Equipment."
NOTE: EN 55022 emissions requirements provide for two
classifications:
• Class A is for typical commercial areas.
• Class B is for typical domestic areas.
To determine which classification applies to your computer,
examine the FCC registration label located on the back panel of
the computer. If the label indicates a Class A rating, the following
warning applies to your computer:
RF INTERFERENCE WARNING: This is a Class A product.
In a domestic environment this product may cause radio
frequency (RF) interference, in which case the user may be
required to take adequate measures.
This Compal device is classified for use in a typical Class B
domestic environment.
A "Declaration of Conformity" in accordance with the preceding
directives and standards has been made and is on file at Compal
Computer Corporation.
CCC Notice (China Only)
On Class A systems, the following warning will appear near the
regulatory label:
Warning: This is a Class A product. In a domestic
environment this product may cause radio interference, in
which case the user may be required to take adequate
measures.
BSMI Notice (Taiwan Only)
Most Compal computer products are classified by the Bureau of
Standards, Meteorology and Inspection (BSMI) as Class B
information technology equipment (ITE).
This Compal device is classified for use in a typical Class B
domestic environment.
CANADIAN DOC NOTICE
This digital apparatus does not exceed the Class B limits for radio
noise emissions from digital apparatus as set out in the Radio
Interference Regulation of the Canadian Department of
Communications.
"Le présent appareil numérique n'èmet pas de bruits
radioélectriques dépassant les limites applicables aux appareils
numériques de la class B prescrites dans le Règlement sur le
brouillage radioélectrique édicté par le ministère des
Communications du Canada"
About this user’s manual
This user’s manual is designed to let you easily find the
information you need to get the most from your notebook.
Chapter 1 introduces you to the features of your computer.
Chapter 2 gives you useful details on using your computer.
Chapter 3 tells you how to look after your notebook computer,
whether at home or traveling.
Chapter 4 talks about PC Card peripherals and how to use them.
Chapter 5 goes into more detail about power management and
explains how to conserve power while on the move.
Chapter 6 gives you tips on solving typical problems you may run
up against.
Chapter 7 introduces you to BIOS, the nervous system of your
computer, and how to change its fundamental settings.
There is no need to read the manual from the beginning to end.
Simply find your way to the section that interests you using the
index, or browse through the manual.
You will come across the following icons in the manual:
Helpful pointers and tricks to get more from your notebook
To help you note and avoid possible damage to your notebook's
hardware or software, or loss of your work
Points out possible damage to property, personal injury or death
Information in this document is subject to change without notice.
© Compal Electronics, Inc. 2003. All rights reserved.
Trademarks used in this document: Microsoft and Windows are
registered trademarks of Microsoft Corporation.
Other trademarks and trade names may be used in this document
to refer to either the entities claiming the marks and names or
their products.
1 Introducing Your Notebook
1.1 Front
1 Case Latch 6 Device Status Lights
2 Display 7 Optical Media Drive
3 Easy Buttons 8 Keyboard
4 TouchPad 9 Power Button
5 TouchPad Buttons 10 Keyboard Status Lights
1.1.1 Case Latch
Secures the display case to your notebook. To open the display,
slide the case latch to the right and lift the display. When you
close the display the case latch secures it automatically.
1.1.2 Display
Your display is either a 14.1" or 15.1” COLOR TFT/XGA or
COLOR TFT/SXGA+ LCD.
1.1.3 Easy Buttons
These buttons launch your favorite programs.
Launches a pre-configured program.
Launches a pre-configured program.
1.1.4 TouchPad
The TouchPad works like a desktop mouse. For more information
see Keyboard and TouchPad in Chapter 2.
1.1.5 TouchPad Buttons
The left and right TouchPad buttons work like the left/right
buttons on a standard mouse.
1.1.6 Device Status Lights
Indicates power on; flashing indicates standby mode.
Indicates battery status. For details, see Battery.
Indicates wireless communication status.
1.1.7 Optical Media Drive
The optical media drive provides a means for you to
import/export data and small files into/from your computer.
Depending on the configuration of your computer, you may
either be able to record CDs or play DVDs.
1.1.8 Keyboard
The keyboard includes a numeric keypad and the Microsoft®
Windows® logo key.
See Keyboard and TouchPad in Chapter 2 for more on using
keyboard shortcuts.
1.1.9 Power Button
Press to turn your notebook on. For more on power settings see
Power Management.
Windows XP, which comes preinstalled, goes into the shutdown
sequence automatically if you press the power button while on.
You can configure this in Control Panel: Power Options – Advanced.
1.1.10 Keyboard Status Lights
Indicates uppercase letter function enabled
Indicates numeric keypad enabled
Indicates scroll lock function enabled
1.2 Right Side
1 Speaker
2 AC Adapter Connector
3 Air Fan
1.2.1 Speaker
To adjust the system speaker volume, look under the Sounds and
Audio Devices Properties of the Control Panel. See Chapter 2 for
more details. Many software programs, such as multimedia
applications, also include their own volume controls.
1.2.2 AC Adapter Connector
to attach the AC adapter to your notebook. You
can connect an AC adapter when your notebook is switched on or
While the AC adapter works with electrical outlets worldwide, power
you
use compatible cable or correctly connect the cable to the power strip
Use this connector
off.
connectors and power strips vary from country to country. Ensure
or electrical outlet. Failure to do so may cause fire or damage to
equipment.
1.2.3 Air Vent
Never block, push objects into, or allow dust to gather in the air vents.
An internal fan creates airflow through the vents, preventing your
notebook from overheating.
When it gets hot, your notebook will switch on the fans, which may
make some noise. This is normal, and does not mean there is a
problem.
Doing so may damage your notebook or cause a fire.
Loading...