Job No. 107876
Instruction Manual
Malone 2 Drw bedside
C o n g r a t u l a t I o n s O N t h e p u r c h a s e
o f y o u r …….
W e l c o m e t o t h e M A L – b s 5 2 …….
MALONE – MAL-BS52 2
For assembly advice or parts go to www.farmersfurniture.co.nz or call 0800 100 858
……the Malone Collection is manufactured right here in New Zealand - by New Zealanders, for New
Zealanders. Honest Kiwi Quality that is backed by our signature 5 Year Guarantee*. If by any chance you
have a problem during this period, OUR promise to YOU is that we will repair or replace. Additionally, being
based right in here New Zealand our experienced team’s expertise is near at hand; if you have any
problems at all during the assembly process, you can give us a call on our Freephone number (0800 100858)
or email us at sales@compacfurniture.co.nz during normal working hours and we will step you through the
process.
The Malone Collection is a modern and stylish collection, designed in response to latest interior trends, both
in New Zealand and overseas. Finished in a latest European trending Smokey Walnut woodgrain, The
Malone Collection is right up with the minute. Paired with a minimalistic streamlined style and an emphasis
on strong horizontal lines, this collection is guaranteed to impress. Fully overlaid drawers give an illusion of
length, attributing to the slim line effect. Thin silver extruded handles enhance this effect, adding to the
overall horizontal theme without complicating surface areas. Tall slim chrome feet contribute the slim-line
effect, and create a feeling of space, by lifting the unit up off the ground.
The Malone Collection is constructed from NZ made MDF, a renewable resource from sustainably managed
pine forests. This means you can have complete confidence that with The Malone Collection, you are
making an environmentally responsible choice.
If you have any questions please visit www.farmersfurniture.co.nz or call the manufacturers direct on 0800
100 858.
WHERE TO ASSEMBLE YOUR BEDSIDE
Assemble your Bedside on a clean and smooth surface, free of anything which may damage the finished
surfaces. A clean, carpeted floor is ideal. If assembling on a workbench or table we suggest you cover it
with the carton the Bedside was packaged in.
Warning! Never leave hardware parts where children can reach them. Small parts may be a choking
hazard!
*5 YEAR GUARANTEE
The Malone Collection carries a 5 year guarantee against defective material or workmanship, excluding
misuse and normal wear and tear. Obviously, as this unit is customer-assembled we cannot guarantee
cabinet failure or damage from incorrect assembly. All claims need proof of purchase – to ensure this
register your Bedside at www.farmersfurniture.co.nz.
Follow the assembly instructions carefully and take note of the precautions below.
Avoid direct sunlight wherever possible.
Keep cabinet in a dry place.
Wipe off spilt liquids immediately.
Avoid placing hot items directly on the surface.
Clean with a slightly damp cloth and buff dry with a soft dry cloth - microfibre is ideal.
Do not allow nail polish, removers, deodorant or other damaging chemicals to come into
contact with the surface.
Did you know……
MALONE – MAL-BS52 3
For assembly advice or parts go to www.farmersfurniture.co.nz or call 0800 100 858
PARTS LIST
Please check you have all the necessary parts before beginning to assembling your Bedside. The
measurements provided will help you to identify each part. If any parts are missing or damaged please
contact the manufacturers directly, either via our website or our 0800 number. Do not call the store you
bought the cabinet from as they will be unable to help you.
QTY
PART NAME
MEASUREMENTS
NOTES
MANUFACTURERS CODE
1
Top
596 x 396 x 15mm
Finished on one side. Blue mark
106428
1
Base
596 x 396 x 15mm
Finished on one side. Purple mark
106429
1
LH End
357 x 377 x 15mm
Finished on one side. Green mark
106430
1
RH End
357 x 377 x 15mm
Finished on one side. Red mark
106431
1
Small Drw Front
584 x 125 x 15mm
Finished on one side
106432
1
Large Drw Front
584 x 221 x 15mm
Finished on one side
106433
1
LH Drw Side – Sml
340 x 95 x 12mm
Finished on both sides. 12mm
106434
1
LH Drw Side - Lrg
340 x 160 x 12mm
Finished on both sides. 12mm
106436
1
RH Drw Side – Sml
340 x 95 x 12mm
Finished on both sides. 12mm
106435
1
RH Drw Side - Lrg
340 x 160 x 12mm
Finished on both sides. 12mm
106437
1
Drawer Back – Sml
508 x 90 x 12mm
Finished on one side. 12mm
106438
1
Drawer Back – Lrg
508 x 155 x 12mm
Finished on one side. 12mm
106405
2
Drawer Bottom
518 x 339 x 4mm
Finished on one side. 4mm
106439
1
Back Panel
377 x 578 x 4mm
Plain 4mm
106440
COLOUR CODING
To help identify the parts, the main components are colour coded with a pen mark on the back edge of
the panel. (The unfinished edge.)
RED Right Hand Parts. (E.g. RH End, RH Division, RH Drawer Side.)
GREEN Left Hand Parts. (E.g. LH End, LH Division, LH Drawer Side.)
BLUE Tops
PURPLE Bases
MALONE – MAL-BS52 4
For assembly advice or parts go to www.farmersfurniture.co.nz or call 0800 100 858
HARDWARE LIST
CABINET HARDWARE
QTY
PART NAME
ASSEMBLY CODE
PICTURE
MANUFACTURERS CODE
4
Connecting Bolts
H1 102649
4
15mm Cams
H2 102511
4
Dowels
H15 102515
8
Small Silver Screws
H61 106618
4
Large Screws
H5 102648
2
Metal Drawer Slide sets
H60 102482
2
Bar Handles
H58
102472
12
Gold Panhead Screws
H7 106118
4
Tall Feet
H59 106092
DRAWER HARDWARE
4
Connecting Bolts
H1 102649
4
12mm Cams
H3 102510
4
Dowels
H15 102515
8
Small Panhead Screws
H61 1026618
8
Screws
H9 102645
MALONE – MAL-BS52 5
For assembly advice or parts go to www.farmersfurniture.co.nz or call 0800 100 858
CAM INSTALLATION & OPERATION GUIDE
The Cam and Connecting Bolt system is used to put your unit together. Below is an explanation of how this
system works.
To see a demonstration click on the assembly assistance tab at www.warehousefurniture .co.nz
DRAWER SLIDES GUIDE
Your pack will contain 2 sets of Full Extension Drawer Slides. Each drawer requires one set. Left and right
sides are interchangeable. Each set consists of two pairs, each of which has two parts, the Cabinet
component and the Drawer component. You will need to separate the two parts before beginning the
assembly process. NOTE: Slides could be greasy.
Each pair of slides in your pack will appear as below.
To separate the two parts of the slide, extend the slide as shown below.
Turn the extended slide onto its reverse side. Lift the black plastic tab as shown below, and slide the end
section of the slide right out, to separate the two pieces. NOTE: This could be a bit stiff.
The two separated pieces will appear as below.
LIFT
Cabinet Component:
Drawer Component:
MALONE – MAL-BS52 6
For assembly advice or parts go to www.farmersfurniture.co.nz or call 0800 100 858
INSTALL THE HARDWARE
STEP 1 - TOP
Lay the Top of the unit finished side down on a clean, clear surface.
Screw four H1 Connecting Bolts into the holes as indicated in the drawing below
H1
STEP 2 – LH END
Lay the LH End on a smooth clean surface with holes facing upwards.
Attach two Cabinet Drawer Slides to the LH End using the H61 Small Silver Screws. Use the holes as
indicated in the diagram below - each slide requires two screws. Ensure that the Slides are facing
the same way as in the diagram.
Insert two H2 Large Cams as shown in diagram. Ensure the arrow on the top of the Cam points
towards the top edge of the End.
Push two H15 Dowels into the top edge of the End.
H1 H2 H61 H15
Front Edge
H61 Small Screw
H61 Small Screw
MALONE – MAL-BS52 7
For assembly advice or parts go to www.farmersfurniture.co.nz or call 0800 100 858
STEP 3 – RH END
Lay the RH End on a smooth clean surface with holes facing upwards.
Attach two Cabinet Drawer Slides to the RH End using the H61 Small Silver Screws . Use the holes as
indicated in the diagram below - each slide requires two screws. Ensure that the Slides are facing
the same way as in the diagram.
Insert two H2 Large Cams as shown in diagram. Ensure the arrow on the top of the Cam points
towards the top edge of the End.
Push two H15 Dowels into the top edge of the End.
H1 H2 H61 H15
ASSEMBLE THE UNIT
STEP 4 - ENDS TO TOP
Stand the Top on its back edge.
Fit the LH End and RH Ends to the underside of the Top. The Connecting Bolts in the Top will fit into
the Metal Cams in the Ends.
Turn the Metal Cams in a clockwise direction to lock the Top to the Ends. Ensure they turn a least a ¼
to ½ a turn.
Front Edge
H61 Small Screw
H61 Small Screw
MALONE – MAL-BS52 8
For assembly advice or parts go to www.farmersfurniture.co.nz or call 0800 100 858
STEP 5 – Back Panel
Carefully turn the bedside onto its Top.
Take the Back Panel. Slide this into place between the grooves in the Ends.
STEP 6 - BASE
Attach the Base using the four H5 Large Screws. Ensure the finished side of the Base faces into the
inside of the Bedside
STEP 7 - BASE
Next screw on the four Tall Feet using the H7 Gold Panhead Screws. Use the pre-drilled holes.
Turn the unit upright. Be careful not to drag or scratch it.
H5
H7
MALONE – MAL-BS52 9
For assembly advice or parts go to www.farmersfurniture.co.nz or call 0800 100 858
ASSEMBLE THE DRAWERS
Your Malone 2 Drawer Bedside has two drawers. Both Drawers are constructed from the same parts and are
therefore assembled the same way.
STEP 8 - INSTALL HARDWARE /DRAWERS
Install the hardware in the drawer parts as shown below. NOTE: Be sure that the arrow on the Small
Cam points to the end of the drawer side nearest it.
H15 H3 H1 H61
DRAWER FRONT
RH DRAWER SIDE
LH DRAWER SIDE
To see a demonstration of
how to put a drawer
together, click on the
assembly assistance tab at
www.farmersfurniture.co.nz
RH Drw Side
MALONE – MAL-BS52 10
For assembly advice or parts go to www.farmersfurniture.co.nz or call 0800 100 858
STEP 9 – sides and bottom
Lay the Drawer Front face down on a smooth, clean surface.
Attach the LH and RH Drawer Sides by fitting them into place over the Connecting Bolts installed in
the Drawer Front.
Turn the Small Cams clockwise to lock the Drawer Sides in place.
Slide the Drawer Bottom into place in the grooves in the Drawer Sides and Drawer Front.
STEP 10 – attach drawer back
Fit the Drawer Back into place between the Drawer Sides. The groove in the Drawer Back will fit over
the end of the Drawer Bottom.
Secure the Drawer Sides to the Drawer Back with four H9 Screws as shown below.
Drawer Front
RH Drw Side
Drawer Back
Drw Back
H9
Drw Front
MALONE – MAL-BS52 11
For assembly advice or parts go to www.farmersfurniture.co.nz or call 0800 100 858
STEP 11 - ATTACH HANDLES AND FIT DRAWERS INTO CABINET
Turn the drawer over and attach the handle using the screws provided.
Fit the drawers into the cabinet. Start with the top drawers and work your way down.
CONGRATULATIONS, YOUR Malone 2 Drawer Bedside IS NOW COMPLETE.
THANK-YOU FOR SUPPORTING NEW ZEALAND MADE FURNITURE
Holding the Drawer level, fit the Slides
installed on the Drawers to the slides installed
in the cabinet. Without forcing, slide the
drawer in until the slides click. It may be
helpful to hold the sliding parts of the
Cabinet slides while you slide the drawer in.
NOTE: Do not force the drawer if it jams. Take
it out and ensure that the slides are lined up
properly before inserting.
Loading...