Comnet RLXE4GE24MODMS-LVPSU, RLXE4GE24MODMS-GE2SFP, RLXE4GE24MODMS-CHASSIS, RLXE4GE24MODMS-HVPSU, RLXE4GE24MODMS-GE4SFP Specsheet
...
Fully Modular, Substation-Rated, All-Gigabit Layer 2 Switch/Layer 3
Router, With 1000 Mbps or 10 Gigabit SFP Uplink Ports
RLXE4GE24MODMS
EXCLUSIVE
ComNet product series RLXE4GE24MODMS is a substation-rated and industrially-hardened
modular-configuration all-gigabit managed layer 2 switch/layer 3 router. The RLXE4GE24MODMS
is intended for deployment in environments where high levels of electromagnetic noise and
interference (EMI) and severe voltage transients and surges are routinely encountered, such as
electrical utility substations and switchyards, heavy manufacturing facilities, track-side electronic
equipment, and other difficult out-of-plant installations. The layer 3 static routing functionality allows
for the participation and foundation of a core network infrastructure.
The user-configurable modularity provides a truly future-proof platform that may be upgraded
or changed in the field at any time, to support changes in the user’s communications and
networking requirements as they arise. Four slots are provided in the chassis for accommodating
individual modules featuring different combinations of SFP* and electrical 10/100/1000BASETX communications ports. The uplink module slot can accept either a 1 gigabit or a 10 gigabit
module, with two or four 1 or 10 Gbps SFP+ ports. Dual user-replaceable redundant power supply
modules provide an extremely high level of switch/router reliability, for those applications where the
possibility of a power supply single-point-of-failure cannot be tolerated.
When configured with the 8-port 100/1000BASE-X SFP or 4 100 or 1000BASE-FX fixed ST or SC
optics communications modules, the RLXE4GE24MODMS may be used for network aggregation
applications, or where it is desirable to provide optical connectivity directly to the switch/router in
electrically-noisy environments.
The RLXE4GE24MODMS supports multiple Ethernet redundancy protocols, including ComNet
C-Ring (recovery time < 30ms, with >250 switches integrated within the ring), and MSTP with RSTP/
STP compatibility. With its extremely fast recovery time, the most mission-critical applications are
fully protected from network interruptions or temporary malfunctions due to possible short or longterm faults or outages within the network.
FEATURES
› Fully compliant with the requirements of IEC 61850-3 and IEEE
1613 Class 2, for use in electrical utility substations; NEMA TS-1/
TS-2 for Traffic Signal Control Equipment; and EN50155 for railway
applications
› Future-proof fully modular configuration supports changes to the
users communications and networking requirements, and simplifies
network planning and design
› Choice of 100Mb, 1000Mb, or 10Gb port speeds, with either SFPs or
fixed ST or SC optics
› Environmentally hardened for deployment in difficult unconditioned
out-of-plant installations: Extended ambient operating temperature
range of -40˚ C to +85˚ C, for use in virtually any environment.
Conformal coating is optionally available for humidity with
condensation or airborne particulate matter environments.
› Dual-redundant power supplies significantly reduce the possibility
of a single-point-of-failure, for the highest system and network
reliability. Multiple AC and DC operating voltages with front or rear
chassis power connection interfaces available.
› Supports IEEE 1588v2 Precision Timing Protocol, Transparent Clock
Synchronization (TC), for protective relaying and control applications
› User-programmable alarm relay for local or remote indication of a
fault condition
› Layer 3 static routing, RIP, and VRRP functions
› C-Ring compatible: Network recovery time <30ms, with >250
switches within the ring, for Ethernet redundancy.
› Com-Ring open architecture supports other switch manufacturers’
ring technologies, for seamless network integration
› MSTP, with RSTP/STP compatibility
XE = 10 GB 4 24-40º TO +85ºSUBSTATION FLEXIBILIT YEN50155
› IEC 62439-2 MRP (Media Redundancy Protocol)
› IPV6 internet protocol (latest version)
› Support for Modbus TCP protocol
› VLAN unaware: Supports priority-tagged frames to be received by
specific IEDs (Intelligent Electronic Devices)
› Provides HTTPS/SSH protocol for enhanced network security
› IEEE 802.3AZ Energy Efficient Ethernet-Compliant
› SMTP client, & IP-based bandwidth management
› Application-based QoS management
› Device Binding security function
› DOS/DDOS auto-prevention
› IGMP v2/v3 (IGMP snooping support) for filtering multicast traffic
› SNMP v1/v2c/v3 & RMON & 802.1Q VLAN Network Management
› ACL, TACACS+ and 802.1x User Authentication for network security
› 9.6K Bytes Jumbo Frame
› Web-based, Telnet, Console (CLI), and Windows utility (eConsole)
configuration
› Rugged 19-inch rack-mount steel housing, 1 RU high (1.75”)
(Can be mounted in front or rear facing orientation)
› No fans or forced-air cooling; cooling via natural convection
eliminates unreliable and troublesome fans/moving parts, with no
periodic maintenance requirements
› Lifetime Warranty
* Small Form-Factor Pluggable Module. Sold separately.
LIFETIME WARRANTY WWW.COMNET.NET TECH SUPPORT: 1.888.678.9427
RLXE4GE24MODMS
A
Fully Modular, Substation-Rated, All-Gigabit Layer 2 Switch/Layer 3
APPLICATIONS
› Electrical substation SCADA and distribution automation
networks; protective relaying systems; power transmission
& distribution systems; remote/unattended wind farm,
hydroelectric, and solar/photovoltaic power generation
facilities; and other electrical utility-specific applications
› NERC-CIP-014 compliance for perimeter security,
surveillance monitoring, and controlled access to electrical
substations and power generating facilities, and other critical
infrastructure/high value, mission-critical sites and assets
› Industrial/Factory Automation & Process Control SCADA
Networks
› Chemical and petrochemical refining and processing
facilities, oil and gas pipelines/transmission systems, and
mining installations
SPECIFICATIONS
Router, With 1000 Mbps or 10 Gigabit SFP Uplink Ports
› Food processing/pharmaceutical manufacturing facilities,
Wastewater treatment plants, and suppliers of potable
drinking water
› ITS/transportation closed-loop signalization and VMS/VDS/
surveillance/incident detection systems
› Railway/trackside control and monitoring system
› Military, government, and defense communications networks
› Integrated IP-video, VOIP, and data transmission networks
› Cellular telephony and wireless backhaul networks
Power
Redundant power input LV PSU: 24/48 VDC, 20 to 72 VDC power inputs
HV PSU: 88~264VAC / 100~370VDC power inputs
Power connections are on rear of chassis as
standard. For front panel power connections please
order /FP chassis option
Power Consumption 46 W Max
Overload Current Protection Present
Mechanical
Fault Contact Relay Relay output to carry capacity of 1A at 24 VDC
Indicating LEDs System Ready Indicator (PWR)
Power Indicator (PWR1 / PWR2)
Ring Master Indicator (R.M.)
Fault Indicator (Fault)
Reset To Default Running Indicator (DEF)
Supervisor Login Indicator (RMT)
Link/Act(LINK)
Speed(SPD)
Duplex(FDX)
Remote (RMT)
Port 1 ~ 28 Link/Act(LK/ACT)
Enclosure 19“ rack mountable chassis
Size 17.32 × 12.8 × 1.73 in (44 × 32.5 × 4.4 cm)
Weight 1.42 lb / 6.45 kg
Environmental
MTBF > 250,000 hours
Storage Temperature -40º to +85ºC
Operating Temperature -40º to + 85ºC
-40º to +75ºC when “XE” modules are in use
Operating Humidity 5 to 95% Non-condensing³
Compliance
Traffic Control NEMA TS-1, NEMA TS-2
Power Automation IEC 61850-3; IEEE 1613, Class 2
EMI FCC Part 15, CISPR (EN55022) class A, EN50155
(EN50121-3-2, EN55011, EN50121-4)
EMS EN61000-4-2 (ESD), EN61000-4-3 (RS),
EN61000-4-4 (EFT), EN61000-4-5 (Surge),
EN61000-4-6 (CS), EN61000-4-8, EN61000-4-11
Connectors
RS232 Console RS-232 in RJ-45 Connector with Console cable
115200 bps, 8, N, 1
Power Screw Terminal
Fault Relay Screw Terminal
RLXE4GE24MODMS/XE2SFP¹ 2 × SFP+
RLXE4GE24MODMS/XE4SFP¹ 4 × SFP+
RLXE4FE24MODMS/GE2SFP 2 × SFP
RLXE4GE24MODMS/GE4SFP 4 × SFP
RLXE4GE24MODMS/8TX 8 × RJ-45
RLXE4GE24MODMS/8SFP¹ 8 × SFP
RLXE4GE24MODMS/GE4SCM2 4 × Duplex SC²
RLXE4GE24MODMS/FE4SCM2 4 × Duplex SC²
RLXE4GE24MODMS/GE4SCS2 4 × Duplex SC²
RLXE4GE24MODMS/FE4SCS2 4 × Duplex SC²
RLXE4GE24MODMS/GE4STM2 4 × Duplex ST²
RLXE4GE24MODMS/FE4STM2 4 × Duplex ST²
RLXE4GE24MODMS/GE4STS2 4 × Duplex ST²
RLXE4GE24MODMS/FE4STS2 4 × Duplex ST²
Ethernet Standards
IEEE 802.3 for 10Base-T
IEEE 802.3u for 100Base-TX and 100Base-FX
IEEE 802.3ab for 1000Base-T
IEEE 802.z for 1000Base-X
IEEE 802.3ae for 10Gigabit Ethernet
IEEE 802.3x for Flow control
IEEE 802.3ad for LACP (Link Aggregation Control Protocol )
IEEE 802.1p for COS (Class of Service)
IEEE 802.1Q for VLAN Tagging
IEEE 802.1D for STP (Spanning Tree Protocol)
IEEE 802.1w for RSTP (Rapid Spanning Tree Protocol)
IEEE 802.1s for MSTP (Multiple Spanning Tree Protocol)
IEEE 802.1x for Authentication
IEEE 802.1AB for LLDP (Link Layer Discovery Protocol)
GENCY COMPLIANCE
LIFETIME WARRANTY WWW.COMNET.NET TECH SUPPORT: 1.888.678.9427
RLXE4GE24MODMS
mm
R0.14 in
SPECIFICATIONS
Fully Modular, Substation-Rated, All-Gigabit Layer 2 Switch/Layer 3
Router, With 1000 Mbps or 10 Gigabit SFP Uplink Ports
Switch Properties
Switching Latency 7μs
Switching Bandwidth 128 Gbps
Max Available VLANs 256
IGMP multicast groups 128 for each VLAN
Port rate limiting User Define
MAC Table 8K
Priority Queues 8
Processing Store-and-Forward
Jumbo Frame Up to 9.6K bytes
Packet Buffer 32 Mbits
Flash Memory 128 Mbits
DRAM Size 1 Gbits
Security Features
Device Binding security feature
Enable/disable ports, MAC based port security
Port based network access control (802.1x)
Single 802.1x and Multiple 802.1x
MAC-based authentication
QoS assignment
Guest VLAN
MAC address limit
TACACS+
VLAN (802.1Q ) to segregate and secure network traffic
Radius centralized password management
SNMPv3 encrypted authentication and access security
Https / SSH enhance network security
Web and CLI authentication and authorization
Authorization (15 levels)
IP source guard
Software Features
Hardware routing, RIP and static routing
IEEE 1588v2 clock synchronization
IEEE 802.1D Bridge, auto MAC address learning/aging and MAC address (static)
Multiple VLAN Registration Protocol (MVRP)
MSTP (RSTP/STP compatible)
Redundant Ring (C-Ring) with recovery time less than 30ms over 250 units
Virtual Router Redundancy Protocol (VRRP)
TOS/Diffserv supported
Quality of Service (802.1p) for real-time traffic
VLAN (802.1Q) with VLAN tagging
IGMP v2/v3 Snooping
IP-based bandwidth management
Application-based QoS management
DOS/DDOS auto prevention
Port configuration, status, statistics, monitoring, security
DHCP Server/Client
DHCP Relay
Modbus TCP
SMTP Client
Voice VLAN supported
NTP Server
DNS client proxy
Network Redundancy
C-Ring
Com-Ring
Legacy Ring
C-Chain
MRP
MSTP (RSTP/STP compatible)
In a continuing effort to improve and advance technology, product specifications are subject to change without notice.
OUTLINE DRAWING
12.8 in
325 .0 mm
440 .0 mm
17.3 in
19. 00 mm
0.75 in
3.9 0 mm
0.15 in
30. 20 mm
1.19 in
R3. 50 mm
44. 00
1.7 in
LIFETIME WARRANTY WWW.COMNET.NET TECH SUPPORT: 1.888.678.9427
RLXE4GE24MODMS
Electrical Substation SCADA Network using RLXE4GE24MODMS
Fully Modular, Substation-Rated, All-Gigabit Layer 2 Switch/Layer 3
Router, With 1000 Mbps or 10 Gigabit SFP Uplink Ports
ORDERING INFORMATION
Part Number Description Compatible Slots
RLXE4GE24MODMS/CHASSIS 4 Slot 10 Gigabit Managed Layer 2/3 Switch (Rear Panel Power Connections) - No PSUs or Modules included n/a
RLXE4GE24MODMS/CHASSIS/FP 4 Slot 10 Gigabit Managed Layer 2/3 Switch (Front Panel Power Connections) - No PSUs or Modules included n/a
RLXE4GE24MODMS/LVPSU Low Voltage Power Supply Module, 24/48 VDC (20~72 VDC) - PSU Only (1 or 2 Per Chassis) PSU 1 or 2
RLXE4GE24MODMS/HVPSU High Voltage Power Supply Module, 88~264 VAC / 100~370 VDC - PSU Only (1 or 2 Per Chassis) PSU 1 or 2
RLXE4GE24MODMS/XE2SFP Industrial 2 × 10GBase-X SFP+ ports - Module Only (requires purchase of SFP+ modules)¹ Slot 4
RLXE4GE24MODMS/XE4SFP Industrial 4 × 10GBase-X SFP+ ports - Module Only (requires purchase of SFP+ modules)¹ Slot 4
RLXE4GE24MODMS/GE2SFP Industrial 2 × 1000Base-X SFP ports - Module Only (requires purchase of SFP modules)¹ Slot 4
RLXE4GE24MODMS/GE4SFP Industrial 4 × 1000Base-X SFP ports - Module Only (requires purchase of SFP modules)¹ Slot 4
RLXE4GE24MODMS/8TX Industrial 8 × 10/100/1000Base-T(X) ports - Module Only Slots 1-3
RLXE4GE24MODMS/8SFP Industrial 8 × 100/1000Base-X SFP ports - Module Only (requires purchase of SFP+ modules)¹ Slots 1-3
RLXE4GE24MODMS/GE4SCM2 Industrial 4 × 1000Base-FX Multimode SC Fiber ports - Module Only² Slots 1-3
RLXE4GE24MODMS/FE4SCM2 Industrial 4 × 100Base-FX Multimode SC Fiber ports - Module Only² Slots 1-3
RLXE4GE24MODMS/GE4SCS2 Industrial 4 × 1000Base-FX Singlemode SC Fiber ports - Module Only² Slots 1-3
RLXE4GE24MODMS/FE4SCS2 Industrial 4 × 100Base-FX Singlemode SC Fiber ports - Module Only² Slots 1-3
RLXE4GE24MODMS/GE4STM2 Industrial 4 × 1000Base-FX Multimode ST Fiber ports - Module Only² Slots 1-3
RLXE4GE24MODMS/FE4STM2 Industrial 4 × 100Base-FX Multimode ST Fiber ports - Module Only² Slots 1-3
RLXE4GE24MODMS/GE4STS2 Industrial 4 × 1000Base-FX Singlemode ST Fiber ports - Module Only² Slots 1-3
RLXE4GE24MODMS/FE4STS2 Industrial 4 × 100Base-FX Singlemode ST Fiber ports - Module Only² Slots 1-3
Options Low Voltage Industrial Power Supply (24 or 48 VDC) (Optional)
User-selectable SFP Modules¹ (Extra charge, consult factory)
[3] Add suffix ‘/C’ for Conformally Coated Circuit Boards to extend to condensation conditions (Extra charge, consult factory)
[1] Multimode fiber needs to meet or exceed fiber standard ITU-T G.651. Single mode fiber needs to meet or exceed fiber standard ITU-T G.652
[2] This product requires a fiber installation with a minimum 30 dB connector return loss. The use of Super Polish Connectors is
recommended. Complies with FDA Performance Standard for Laser Products, Title 21, Code of Federal Regulations, Subchapter J.
APPLICATION DRAWING
Protective Relay
IED
RLXE4GE24MODMS
RTU IED
Metering
RTU
RLXE4GE24MODMS
Substation B
RTUMetering IP Camera
Substation A
Protective Relay
Protective RelayProtective Relay Synchrophasor
RLXE4GE24MODMS
IP Camera
RLXE4GE24MODMSRLXE4GE24MODMS
IEEE 1588v2
Precision Timing Required
RLXE4GE24MODMS
Substation C
Synchrophasor
IED
IEEE 1588v2
IED
Engineering
Enterprise
Access
RLXE4GE24MODMS
System Control
& Monitoring
Access
Central Control
& Monitoring Center
3 CORPORATE DRIVE
|
DANBURY, CONNECTICUT 06810
8 TURNBERRY PARK ROAD
|
GILDERSOME
|
MORLEY
|
|
USA
T: 203.796.5300
|
LEEDS, UK LS27 7LE
|
F: 203.796.5303
|
T: +44 (0)113 307 6400
|
|
F: +44 (0)113 253 7462
© 2016 Communic ation Netwo rks. All Right s Reserv ed. “ComNet ” and the “ComNe t Logo” are regis tered tra demarks of Com munication Net works.
TECH SUPPORT: 1.888.678.9427
|
INFO-EUROPE@COMNET.NET
|
INFO@COMNET.NET
16 Aug 2016
Loading...