Comnet RLMCSFP-48DC-M12, RLMCSFP-48DC, RLMCSFP-HV-M12rs, RLMCSFP-HV, RLMCSFP-24DC-M12 User Manual

...

Download

INSTALLATION AND OPERATION MANUAL

RLMCSFP Series

Electrical Substation-Rated 10/100/1000 Mbps Ethernet Media Converter

This manual serves the following ComNet Model Numbers:

RLMCSFP24DC

RLMCSFP48DC

RLMCSFPHV

The ComNet RLMCSFP is designed for deployment in environments where high levels of electromagnetic noise and interference (EMI) and severe voltage transients and surges are routinely encountered.

The DIP-switch-selectable 100BASE-FX or 1000BASE-FX port supports conventional CAT-5e/CAT-6 copper or optical transmission media by selection of the appropriate ComNet SFP module.

User-selectable link fault pass-through provides remote indication of a network fault, and a summary fault alarm provides a local or remote indication via Form C dry contact closure in the event of loss of optical link or operating power.

The 10/100/1000BASE-TX port supports both auto-negotiation and automatic MDI/ MDI-X crossover for full and half-duplex operation; manual MDI/MDI-X switching is not required.

LED indicators confirm operational status.

See Figures 1 – 6 for complete operation details.

The RLMCSFP is DIN-rail or panel-mountable. See Figure A on the last page for mounting instructions.

INS_RLMCSFP_REV–

Rev. 27 Jun 2016

INSTALLATION AND OPERATION MANUAL RLMCSFP SERIES

Figure 1 – RLMCSFP Series Front

Panel

Figure 2 – RLMCSFP24DC and

RLMCSFP48DC Bottom Panel

9 9

Figure 3 – RLMCSFPHV Bottom

Panel

Table 1 – RLMCSFP24DC Physical Feature Descriptions

Call-out Description Manual Reference

Unit Model Number (Be sure to refer to any speciﬁc instructions for your unit variation) –

100/1000 Mbps SFP Fiber Optic Port (Fiber Type and Quantity are dependent on installed SFP) See Installation Instructions, Step 

10/100/1000 TX RJ-45 Port 1 and Port 1 Link/Activity (L/A) and Speed LED Indicators

SFP Port Link Status and SFP Port Link Speed LED Indicators See Table 4 - Indicating LEDs

Power LED Indicator See Table 4 - Indicating LEDs

User-selectable DIP Switches

Fault Relay Connections

Power Connections

Chassis GND Lug See Installation Instructions, Step 3

See Installation Instructions, Step 8 See Table 5 - Indicating LEDs

See Installation Instructions, Steps 1 - 2 See Table 2 - DIP Switch Settings See Figure 4 - DIP Switches

See Installation Instructions, Step 4 See Figure 6 - Fault Relay Operation

See Installation Instructions, Step 7 See Table 3 - Power Connections per Use Case

TECH SUPPORT: 1.888.678.9427

INS_RLMCSFP_REV–

Rev. 27 Jun 2016 PAGE 2

INSTALLATION AND OPERATION MANUAL RLMCSFP SERIES

Installation Instructions

Figure 4 – DIP Switches

DIP Switches on RLMCSFP24DC and RLMCSFP48DC Models

DIP Switches on RLMCSFPHV Model

Table 2 – DIP Switch Settings

SW NAME OFF (DOWN) ON (UP)

1 Link Fault Enable Port 1 Link Fault Pass-Through Disabled Link Fault Pass-Through Enabled

2 N/A N/A N/A

3 FFE Fiber Fault Relay Disabled Fiber Fault Relay Enabled

4 PS Fault Enable Power Supply Fault Relay Disabled Power Supply Fault Relay Enabled

5 N/A N/A N/A

6 1000/100 (SFP Speed)

1 - SET DATA RATE DIP SWITCHES

Locate the 100/1000 data rate DIP switch on the bottom panel of the unit. Set the data rate according to bandwidth required.

NOTE: If two units are connected via the SFP Port, the data rate must be set the same on both units, and must match the data rate of the installed SFPs. Data rate settings are read on start-up, so restart the unit after making any changes.

2 - SET FAULT DIP SWITCHES (UTP MODELS ONLY, FOR COAX MODELS SKIP TO STEP 3)

Locate the LFE, FFE, and PSE DIP switches on the bottom panel of the unit. LFE1: If the Copper Port is Down or Not Connected, the Optical Port will turn on and off at a ~1 sec rate to indicate copper port

fault and the alarm relay will be triggered.

FFE: If the optical link is lost or there is a power failure then the alarm relay output will be triggered.

NOTE: You may select multiple fault event triggers. NOTE: Power Supply Fault DIP Switch is only available on Redundant Power Models. When a redundant power supply is available, a failure of power on one power supply will trigger the alarm relay output. NOTE: Restart not required when making changes to this DIP switch setting.

100 Mbps Speed Set Speed must match speed of installed SFP. Reset power if switch or SFP is changed.

1000 Mbps Speed Set. Speed must match speed of installed SFP. Reset power if switch or SFP is changed.

3 - CONNECT GROUND WIRING

Connect Ground Wiring to ground screw and tighten nut to secure.

4 - CONNECT FAULT RELAY WIRING

Connect Fauly Relay device to 3-pin terminal block. The COM to N/O will be shorted in the fault condition.

5 - CONNECT DATA WIRING

Connect RJ-45 Ports to field wiring using Cat5/5e/6 cable.

6 - CONNECT NETWORK WIRING

Using fiber optic cabling appropriate to the installed SFP, connect the unit to a network device.

TECH SUPPORT: 1.888.678.9427

INS_RLMCSFP_REV–

Rev. 27 Jun 2016 PAGE 3

INSTALLATION AND OPERATION MANUAL RLMCSFP SERIES

Installation Instructions (Continued)

7 - CONNECT POWER

Connect power to unit per the following table.

Table 3 – Power Connections per Use Case

Operating Voltage

Use Power Connectors

Contact the ComNet Design Center, or refer to the appropriate installation and operation manual when configuring and specifying power for a deployment.

8 - VERIFY FUNCTIONALITY

See LED Indicator table below and Troubleshooting Guide if corrective action is needed.

RLMCSFP24DC RLMCSFP48DC RLMCSFPHV

Redundant Inputs 9 to 36 VDC (max)

Vin1+ and Vin1- for PS 1 Vin2+ and VIN2- for PS 2

Redundant Inputs

36 to 59 VDC (max)

Vin1+ and Vin1- for PS 1 Vin2+ and VIN2- for PS 2

88 to 300 VDC (max)

85 to 264 VAC (max)

+/L, -/N, and Earth GND

Table 4 – Front Panel LED Indicators

SFP Link SFP Speed Fault Power

GREEN Solid Communication link has been established

over optical ﬁber. Flashes when data is being transmitted.

Flashing Fiber failure or copper failure (Link Fault

Enable must be switched set to ON)

RED Solid – 100 Mbps Fault (NO-COM) –

OFF Communication link has not been

established.

1000 Mbps No Fault (NC-

COM)

– – –

Unit is not correctly powered up or DIP Switch incorrectly set. (Reset power after switch change.)

Unit is not correctly powered up

Power Applied

Unit is not correctly powered up

Table 5 – Electrical Port LED Indicators

Figure 5 – Electrical Port

Ethernet

Speed

Ethernet

Link /

Activity

GREEN Solid Communication link has been established over the electrical cable –

YELLOW – 1000 Mbps Speed

OFF Communication link has not been established. 10/100 Mbps Speed

Link / Activity

Flashing Data is being transmitted over the elec trical cable –

Speed

Figure 6 - Fault Relay Operation

The fault relay is normally closed and will open on any of the following alarm conditions:

- Link Fault is enabled on the remote RLMCSFP unit and the corresponding copper port has been disconnected.

- Link Fault is enabled on the local RLMCSFP unit and the corresponding copper port has been disconnected.

- Fiber Fault is enabled on the local RLMCSFP unit and the fiber link is down or the power has been lost to either the local or remote RLMCSFP unit.

Table 6 – Troubleshooting Guide

Problem Steps to Take

Power LED not lighting Check that power is properly applied to the unit using the correct connector pair.

No Communication Check Ethernet Link LEDs, Fiber Optic Link LEDs. Confirm Connections, DIP switches are set properly. Verify that the Data Rate switches are set

to the same data rate on back-to-back units and match the installed SFP. Restart the unit if the Data Rate Switch or installed SFP has changed.

TECH SUPPORT: 1.888.678.9427

INS_RLMCSFP_REV–

Rev. 27 Jun 2016 PAGE 4

MECHANICAL INSTALLATION INSTRUCTIONS

Installation Considerations

This product is supplied as Standalone/Surface Mount module. Units should be installed in dry locations protected from extremes of temperature and humidity.

WARNING: Unit is to be used with a Listed Class 2 power supply.

IMPORTANT SAFEGUARDS:

A) Elevated Operating Ambient - If installed in a closed or multi-unit rack assembly, the operating ambient temperature of the rack environment may be greater than

room ambient. Therefore, consideration should be given to installing the equipment in an environment compatible with the maximum ambient temperature (Tma) specified by the manufacturer.

B) Reduced Air Flow - Installation of the equipment in a rack should be such that the amount of air flow required for safe operation of the equipment is not compromised.

Figure A

Dimensions and mounting methods for a ComNet Reliance mini DIN Rail module

INS_RLMCSFP_REV–

Rev. 27 Jun 2016 PAGE 5

Comnet RLMCSFP-48DC-M12, RLMCSFP-48DC, RLMCSFP-HV-M12rs, RLMCSFP-HV, RLMCSFP-24DC-M12 User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual