Comnet FVTRDS1B Specsheet
FVTRD(M)(S)1
10-bit digital bi-directional video or video sync
+ bi-directional data
Description
The ComNet™ FVTRD(M)(S)1 series video transmitter/
receiver and data transceiver supports simultaneous
transmission of short-haul quality 10-bit bi-directional
digital video or video sync plus bi-directional data
over one multimode or single mode optical fiber.
The module is universally compatible with major
CCTV camera manufacturers and supports RS232,
RS422 and 2 or 4-wire RS485 data interfaces, and
most major data protocols. Plug-and-play design
ensures ease of installation and no electrical or optical
adjustments are ever required. Bi-color (Red/Green)
LED indicators are provided for rapidly ascertaining
equipment operating status. Packaged in the exclusive
ComNet ComFit housing, these units may be either wall
or rack-mounted, or may be DIN-rail mounted by the
addition of ComNet model DINBKT1 adaptor plate.
V
D
1
Features
- 10-bit digital bi-directional video transmission or video
sync + bi-directional data
- Exceeds all requirements for RS-250C short-haul
transmission: True broadcast video performance
- Supports RS232, RS422 or RS485 (2 or 4-wire)
data interfaces
- Compatible with all NTSC, PAL, or SECAM CCTV
camera systems
- Tested and certified by an independent laboratory for
full compliance with the environmental requirements
(ambient operating temperature, mechanical shock,
vibration, humidity with condensation, high-line/low-line
voltage conditions and transient voltage protection) of
NEMA TS-1/TS-2 and the Caltrans Specification for Traffic
Signal Control Equipment.
- Voltage transient protection on all power and signal
input/output lines provides unconditional protection
from power surges and other voltage transient events.
1
Applications
- High-Performance CCTV with PTZ Control
LIFETIME WARRANTY WWW.COMNET.NET TECH SUPPORT: 1.888.678.9427
- Automatic resettable fuses on all power lines
- Hot-swappable rack modules
- Interchangeable between stand-alone or rack mount use
– ComFit
- Distances up to 30 miles (48 km)
- Bi-color (Red/Green) LED status indicators provide
rapid indication of critical operating parameters
- Lifetime Warranty
FVTRD(M)(S)1
specifications
10-bit digital bi-directional video or video sync
+ bi-directional data
VIDEO
Video Input: 1 volt pk-pk (75 ohms)
Overload: >1.5V pk-pk
Bandwidth: 5 Hz - 10 MHz
Differential Gain: <2%
Differential Phase: <0.7˚
Tilt: <1%
Signal-to-Noise Ratio (SNR): 67 dB @ Maximum
Optical Loss Budget
Max. RG-59 COAX Distance: 100m (300ft) Camera to Fiber Optic
Module to maintain 6Mhz Bandwidth
DATA
Data Format: RS232, RS422, 2 or 4-wire RS485
w/Tri-State, Manchester and bi-phase
Data Rate: DC-115 Kbps (NRZ)
WAVELENGTH 1310/1550 nm, MM and SM
NUMBER OF FIBERS 1
OPTICAL EMITTER Laser Diode
LED INDICATORS - Video - Received Data
- Transmitted Data
- Optical Carrier Detect
MADE IN THE
USA
CONNECTORS
Optical: ST (Standard)
SC or FC (Optional)
Power: Terminal Block
Video: BNC (Gold Plated Center-Pin)
Data: Terminal Block
ELECTRICAL & MECHANICAL
Power:
Surface Mount: 8-15 VDC @ 2W
Rack Mount: From Rack
Number of Rack Slots: 1
Current Protection: Automatic Resettable Solid-State
Current Limiters
Circuit Board: Meets IPC Standard
Size (in./cm) (L×W×H) 6.1 × 5.3 × 1.1 in.,
(15.5 × 13.5 × 2.8 cm)
Shipping Weight: <2 lb./0.9 kg
ENVIRONMENTAL
MTBF: >100,000 hours
Operating Temp: -40˚ C to +75˚ C
Storage Temp: -40˚ C to +85˚ C
Relative Humidity: 0% to 95% (non-condensing)
†
May be extended to condensation conditions by adding suffix ‘/C’
to model number for conformal coating.
†
PART
NUMBER
FVTRDM1A
FVTRDM1B
FVTRDS1A
FVTRDS1B
Accessories
Options
NOTE: This product requires a fiber installation with a minimum 30 dB connector return loss. The use of Super Polish Connectors is recommended.
**Distance may be limited by optical dispersion. Check with control system manufacturer for distance limits on up-the-coax systems.
Complies with FDA Performance Standard for Laser Products, Title 21, Code of Federal Regulations, Subchapter J
In a continuing effort to improve and advance technology, product specifications are subject to change without notice.
DESCRIPTION
Video Transmitter/Data Transceiver
Video Receiver/Data Transceiver
Video Transmitter/Data Transceiver
Video Receiver/Data Transceiver
9 Volt DC Plug-in Power Supply, 90-264 VAC, 50/60 Hz (Included)
Add ‘/C’ for Conformally Coated Circuit Boards (Extra charge, consult factory)
Add ‘/SC’ for SC Connectors
Add ‘/FC’ for FC Connectors
DIN-Rail Mounting Adaptor Plate Kit – With mounting hardware (Optional, order model DINBKT1)
FIBERS
REQUIRED
1
1 48 km (30 miles)16 dB
FIBER
Multimode
62.5/125µm
Single Mode
9/125µm
OPTICAL
PWR BUDGET
V V
FVTRDS1A
D D
1 Fiber
9/125µm SM
Up to 48 km
(30 miles)
FVTRDS1B
OPTICAL FIBER
VIDEO (Coax)
MAX.
DISTANCE**
3 km (2 miles)16 dB
# RACK
SLOTS
1
1
3 CORPORATE DRIVE | DANBURY, CT 06810 | USA
T: 203.796.5300 | F: 203.796.5303 | TECH SUPPORT: 1.888.678.9427 | INFO@COMNET.NET
8 TURNBERRY PARK ROAD | GILDERSOME | MORLEY | LEEDS, UK LS27 7LE
T: +44 (0)113 307 6400 | F: +44 (0)113 253 7462 | INFO-EUROPE@COMNET.NET
06.11.10© 2010 Communications Networks Corporation. All Rights Reserved. “ComNet” and the “ComNet Logo” are registered trademarks of Communication Networks, LLC.
Loading...