Comnet FVT109B, FVR109B, FVR109BM1ID, FVR109BS1ID, FVT109BM1ID Installation And Operation Manual

...
Page 1
INSTALLATION AND OPERATION MANUAL
FVT/FVR109B(M,S)1[ID]/Bosch
10-BIT DIGITAL VIDEO WITH BOSCH BI-PHASE AND BILINX™ CAMERA CONTROL
The ComNet FVT109B(M,S)1ID/Bosch is the “camera” end of a video and bi-directional data link for the Bosch AutoDome cameras.
The FVT109B(M,S)1ID/Bosch mounts directly inside the AutoDome and supports Bosch “Up-the-Coax” (Bilinx) controls signals for both NTSC and PAL video formats. For the US video format (NTSC) and the European video format (PAL) the distance is 48 km.
The transmitter/receiver pair provides broadcast quality video transmission along with camera control signals.
The FVR109B/Bosch can be mounted as a stand-alone module, fit in the ComNet rack (ComFit packaging) or be mounted on a DIN Rail using the ComNet DINBKT1 adapter.
Bi-color (Red/Green) LED indicators are provided for rapidly ascertaining equipment operating status. Figure 5 on Page 4 describes the LED indicators for each light on the unit.
See Figures 1 – 5 for complete installation instructions.
INS_FVTFVR109B/Bosch_REV–
08/16/11
PAGE 1
Page 2
INSTALLATION AND OPERATION MANUAL FVT/FVR109B(M,S)1[ID]/BOSCH
FIGURE 1 – FVT109B(M,S)1ID/Bosch
TRANSMITTER
CONNECTIONS FOR BOSCH CAMERA FIBER MODULE:
IN-DOME VIDEO TRANSMITTER MODULE (FVT109B(M,S)1ID/Bosch / PCA1144):
1. Connect power and data from the camera to the module: Attach to module at J5 (8-pin male connector with white plastic shroud) with Bosch’s 5-pin to 8-pin cable assembly. Video LED D1 should illuminate red. Data LED D2 should stay off. Link LED D3 should illuminate red.
2. Connect video from camera to module: Attach to module at J4 (2-pin male connector with white plastic backing) with ComNet’s 2-pin to BNC cable. Video LED D1 should illuminate green.
3. Connect fiber to module: Attach single-mode fiber to U11 (single SC fiber optic con­nector). Link LED should illuminate green once receiver is powered on and link is established over the fiber.
MULTIMODE OR SINGLE MODE OPTICAL FIBER
4. Attach module to Bosch’s metal camera insert with white plastic stand-offs. Stand-offs snap into the three gold mounting holes in the module. Secure the insert and attached module in camera with screws.
NOTE: Data LED D2 will flash green when Bosch Bi-phase data is received.
EXTERNAL VIDEO RECEIVER MODULE (FVR109B(M,S)1/Bosch):
1. Connect power to module: Use +9 VDC adapter included with module, or insert into ComNet rack. POWER LED should illuminate green. LINK LED should illuminate red. VIDEO LED should illuminate red. DATA LED should stay off.
2. Connect video output to monitor: Attach to BNC connector labeled VIDEO OUT
3. Connect fiber to module: Attach single-mode fiber to SC fiber optic connector labeled OPTICAL.
4. If Bi-phase data is used to control the camera then connect data to screw terminal block on module: Bi-phase CODE+ should be connected to DIN+. Bi-phase CODE- should be connected to DIN-. Shield should be connected to GND.
NOTE: LINK LED will illuminate green once a link is established over optical fiber with the In-Dome Transmitter module.
VIDEO LED will illuminate green when active signal is detected at the BNC. DATA LED will flash green when Bi-phase commands are detected at the data connector.
TECH SUPPORT: 1.888.678.9427
INS_FVTFVR109B/Bosch_REV–
08/16/11
PAGE 2
Page 3
INSTALLATION AND OPERATION MANUAL FVT/FVR109B(M,S)1[ID]/BOSCH
FIGURE 2 – FVR109B(M,S)1/Bosch RECEIVER
MULTIMODE OR SINGLE MODE OPTICAL FIBER
BLACK
BLACK WITH WHITE STRIPES
FIGURE 3 – FVR109B(M,S)1/Bosch RECEIVER
FRONT PANEL
REAR PANEL
NOTE: Remove Electrical
Connector for Rack Mount Units
TECH SUPPORT: 1.888.678.9427
INS_FVTFVR109B/Bosch_REV–
08/16/11
PAGE 3
Page 4
INSTALLATION AND OPERATION MANUAL FVT/FVR109B(M,S)1[ID]/BOSCH
FIGURE 4 – DATA CONNECTIONS
Customer
FVT109BID/Bosch
DIN(+)
DIN(–)
Bi-phase
Equipment
Data Out (+)
Data Out (–)
FIGURE 5 – LED INDICATORS (FVR109B/Bosch)
LINK VIDEO DATA IN POWER
GREEN Communication link
has been established
over optical fiber
RED Communication
link has not been established.
OFF Unit powered down.
An active video signal
is present on the BNC
connector.
An active data signal is
present on the pins of
the data connector.
Unit powered up
FVR109B/Bosch
DOUT(+)
DOUT(–)
Customer
Equipment
Data In (+)
Data In (–)
TECH SUPPORT: 1.888.678.9427
INS_FVTFVR109B/Bosch_REV–
08/16/11
PAGE 4
Page 5
MECHANICAL INSTALLATION INSTRUCTIONS
Installation Considerations
This fiber-optic link is supplied as a Standalone/Rack module. Units should be installed in dry locations protected from extremes of temperature and humidity.
C1-US, C1-EU, C1-AU or C1-CH Card Cage Racks
CAUTION: Although the units are hot-swappable and may be installed without turning power off to the rack, ComNet recommends that the power supply be turned off and that the rack power supply is disconnected from any power source. Note: Remove electrical connector before installing in card cage rack.
1. Make sure that the card is oriented right side up, and slide it into the card
guides in the rack until the edge connector at the back of the card seats in the corresponding slot in the rack’s connector panel. Seating may require thumb pressure on the top and bottom of the card’s front panel.
CAUTION: Take care not to press on any of the LEDs.
2. Tighten the two thumb screws on the card until the front panel of the card is
seated against the front of the rack.
WARNING: Unit is to be used with a Listed Class 2 or LPS power supply rated
8-15 VDC @ 350 mA.
IMPORTANT SAFEGUARDS: A) Elevated Operating Ambient – If installed in a closed or multi-unit rack
assembly, the operating ambient temperature of the rack environment may be greater than room ambient. Therefore, consideration should be given to installing the equipment in an environment compatible with the maximum ambient temperature (Tma) specified by the manufacturer.
FIGURE A
Dimensions are for a standard ComNet™ one slot module
.156 [3.96 mm]
.313 [7.95 mm]
B) Reduced Air Flow – Installation of the equipment in a rack should be such
that the amount of air flow required for safe operation of the equipment is not compromised.
© 2012 Communications Net works Corp oration. All Rights Reserved. “ComNet ” and the “ComNet Logo” are r egistered tr ademarks of Communication Networks, L LC.
3 CORPORATE DRIVE | DANBURY, CT 06810 | USA T: 203.796.5300 | F: 203.796.5303 | TECH SUPPORT: 1.888.678.9427 | INFO@COMNET.NET
8 TURNBERRY PARK ROAD | GILDERSOME | MORLEY | LEEDS, UK LS27 7LE T: +44 (0)113 307 6400 | F: +44 (0)113 253 7462 | INFO-EUROPE@COMNET.NET
INS_FVTFVR109B/Bosch_REV–
08/16/11
PAGE 5
Loading...