INSTALLATION AND OPERATION MANUAL
CNFE1EOC-M
FAST ETHERNET OVER VDSL2 (EoVDSL)
The ComNet™ CNFE1EOC-M is an environmentally hardened modem that
supports Ethernet over twisted pair or coaxial cable. The devices use VDSL
(EoVDSL) technology to support data rates up to 90 Mbs. Ethernet data may be
transmitted over a telephone-grade twisted copper pair, legacy serial cabling
or standard 75Ω coaxial cable circuits. These modems allow for upgrading of
a legacy twisted copper or coaxial cable plant for use with Ethernet rather than
installing new network cabling.
The fastest usable data rate is automatically selected, depending upon the
transmission distance and cable quality. The CNFE1EOC-M may be deployed in
most out-of-plant installations, such as those found in intelligent transportation
systems and factory automation/control applications. LED status indicators are
provided for rapidly ascertaining the operating status of the modem and the
link.
See Figures 1 – 5 for complete installation details.
The CNFE1EOC-M small size unit operates as standalone module only. See
Page 5 for mounting instructions.
INS_CNFE1EOC-M_REV–
04/09/10
PAGE 1
INSTALLATION AND OPERATION MANUAL CNFE1EOC-M
FIGURE 1 – CNFE1EOC-M SMALL SIZE UNIT
CAT5e/6
FIGURE 2 – CNFE1EOC-M SMALL SIZE UNIT
REAR PANELFRONT PANEL
COAX (75Ω)
COPPER PAIR
BLACK
BLACK WITH WHITE STRIPE
TECH SUPPORT: 1.888.678.9427
INS_CNFE1EOC-M_REV–
04/09/10
PAGE 2
FIGURE 3 – POSSIBLE ETHERNET CONFIGURATIONS
Ethernet IEEE 802.3 Network Element determined by user.
Coaxial (75Ω)
No Connection
Ethernet IEEE 802.3
Network Element
Ethernet IEEE 802.3
Network Element
CAT5e/6 with
RJ45 Connections
100m (328ft)
CAT5e/6 with
RJ45 Connections
100m (328ft)
CNFE1EOC-M
(Master*)
CNFE1EOC-M
(Master*)
OR
No Connection
Copper Pair
CNFE1EOC-M
(Remote)
CNFE1EOC-M
(Remote)
CAT5e/6 with
RJ45 Connections
100m (328ft)
CAT5e/6 with
RJ45 Connections
100m (328ft)
Ethernet IEEE 802.3
Network Element
Ethernet IEEE 802.3
Network Element
* Master unit located at video source.
TECH SUPPORT: 1.888.678.9427
INS_CNFE1EOC-M_REV–
04/09/10
PAGE 3
FIGURE 4 – LED INDICATORS
LINE STATUS (STAT)
GREEN
RED
OFF
Line side activity Remote Confi guration Unit powered up
– Master Confi guration –
No activity Unit powered down
RED MASTER (M/RD) or
GRN REMOTE (R/GN) POWER
LED STATUS
UNIT STATUS
Low Constant Flashing Fast Constant Flashing On Intermittent Flashing
Idle (Line Is Not Connected) Master/Remote Negotiating Idle (Line Is Connected) Data Flow
FIGURE 5 – SWITCH SETTINGS
SWITCH DOWN (ON) UP (OFF) DEFAULT SETTING
1 Remote Master One ON, one OFF as a pair
2 Forward Error Correction Off Forward Error Correction On ON
3 Asymmetrical Data Symmetrical Data ON
4 Long Reach > 1000ft (305m) Short Reach < 1000ft (305m) ON
TECH SUPPORT: 1.888.678.9427
INS_CNFE1EOC-M_REV–
04/09/10
PAGE 4
MECHANICAL INSTALLATION INSTRUCTIONS
INSTALLATION CONSIDERATIONS
This fiber-optic link is supplied as a Standalone module. The unit is
provided with a mounting plate with holes for two No. 6 pan head
screws (3mm or 3.55mm). See Figure A.
Units should be installed in dry locations protected from extremes of
temperature and humidity.
NOTE: Unit is to be used with a Listed Class 2 or LPS power supply rated 9-12
VDC @ 1A.
FIGURE A
Dimensions are for a standard ComNet™ medium module
3 CORPORATE DRIVE | DANBURY, CT 06810 | USA
T: 203.796.5300 | F: 203.796.5303 | TECH SUPPORT: 1.888.678.9427 | INFO@COMNET.NET
8 TURNBERRY PARK ROAD | GILDERSOME | MORLEY | LEEDS, UK LS27 7LE
T: +44 (0)113 307 6400 | F: +44 (0)113 253 7462 | INFO-EUROPE@COMNET.NET
© 2010 Communications Networks Corporation. All Rights Reserved. “ComNet” and the “ComNet Logo” are registered trademarks of Communication Networks, LLC.
INS_CNFE1EOC-M_REV–
04/09/10
PAGE 5
Loading...