Community VB-TILT Instructions

VB-TILT
VERIS 2 Series Tilting Bracket
Tilting bracket for Community’s VERIS 2 installation series loudspeakers
The VB-TILT Tilting bracket is specifically designed for use with the Community VERIS 2 Series of insta llation l oudspeak ers. It i s a two-part rotat ional d evice that fastens t o a yoke br acket or to other hardware, enabling precise angling of one VERIS 2 loudspeaker enclosure in relation to another. It can be used with all full-range VERIS 2 loudspeakers (models V2-6, V2-8, V2-26, V2-28, V2-12, V2-15, V2-32 and V2-35).
It is strongly recommended that the VB-TILT bracket be used in conjunction with a VERIS 2 horizontal mounting yoke or CMKIT ceiling mount kit as listed in Table 1. All VERIS 2 yokes are designed to accept the VB-TILT bracket and provide a wide range of aiming and tilting options. The VB-TILT bracket attaches directly to the yoke, permitting one loudspeaker enclosure to be angled in relation to another in two axes.
It is also possible to mount the VB-TILT bracket directly to an enclosure rigging p oint on large VERIS 2 models V2-12, V2-15, V2-32 and V2-35. However, caution must be taken not to place undue torque on the fitting or to exceed the single point working load limit. Each enclosure rigging point is rated at 100 lbs working load limit (WLL) with a 10:1 safety ratio.
The VB-TILT bracket is available in b lack or white finishes to match the color of the enclosure. Bracket parts are made of black or white powder coated steel. The hardware used for t he attachment must be load-rated for the intended purpose. Also ensure that the structure you are attaching to is capable of supporting the loudspeaker and bracket assembly. This must include any torque load that may be applied to the structure as a result of the loudspeaker position and aiming angle.
The VB-TI LT p r ovides a hig h degree of safety for s up por ting the loud spe ak er enclosure w hen used correctly. M o unti n g methods ot her tha n those s hown in t his guide shou ld be carefully c ons idered s o that undu e stra in and po ssib le failure of the mounting points does not occur.
VB-TILT Parts List
Rotational Bracket (1) Suspension Bracket (1) M10 30mm Bolt (2) M10 Flat Washer (4) M10 Split Lock Washer (2) M10 Hex Nut (2)
The installer must supply all other hardware for the installation.
M10 35mm Shoulder Eyebolt (1) M8 25mm Bolt (2) M8 Flat Washer (4) M8 Split Lock Washer (2) M8 Hex Nut (2)
Table 1: Optional Mounting Brackets for Use with VB-TILT
It is strongly recommended to use the VB-TILT with other VERIS 2 Series mounting brackets as listed below.
Loudspeaker
Model
V2-6 Included with Loudspeaker CMKIT
V2-8 Included with Loudspeaker CMKIT V2-26 Included with Loudspeaker CMKIT V2-28 Included with Loudspeaker CMKIT V2-12 VB-Y12 CMKIT V2-15 VB-Y15 CMKIT V2-32 VB-Y32 CMKIT V2-35 VB-Y35 CMKIT
Horizontal Mountin g Yo ke
Part No.
Ceiling Mount Kit
Part No.
Figure 1: VB-TILT Bracket Dimensions
Figure 2: VB-TILT Assembly
Using the VB-TILT with the CMKIT
For complete instructions on using the VB-TILT with the CMKIT ceiling mount kit, refer to t he CMKIT instruction guide.
Assembly Instructions – Using the VB-TILT with VERIS 2 Yokes
1. The VB-T ILT com es assembled from the Community Factory with the hardware finger-tight; there is no need to assemble most individual parts. The nuts and bolts must be tightened to their final torque settings in the specific order outlined in steps 2 and 3 below to avoid improper installation, injury, or even death.
2. Attach the Rotational Bracket to the desired VERIS 2 Yoke using the provided M10 nuts, bolts and washers. The Yoke should be placed between the bottom of the Rotational Bracket and the lower M10 flat washers. Once the Rotational Bracket is in the final desired position on the Yoke, tighten the M10 hardware to secure the bracket assembly to the Yoke.
3. After determining that the Rotational Bracket is in the correct position for the desired loudspeaker aiming (see instructions and aiming limitations below), tighten the 8mm bolts that join the Suspension Bracket to the Rotational Bracket.
VB-TILT Application and Aiming Instructions
NOTE: The recommended application of the VB-TILT bracket requires that the loudspeaker’s center of
gravity (COG) be located directly under and in alignment with the center suspension point of the Suspension Bracket (see Figure 3 below). This method of mounting is intended to minimize any torque load placed on the structural attachment point(s). The following instructions and angle adjustment ran ges are provided taking into account this COG r estriction.
Figure 3: Recommended COG Alignment
Figure 4: VB-TILT Yoke Attachment Points
NOTE: Each VERIS 2 Yoke has multiple attachment points for the VB-TILT Bracket including:
a.) Two (2) holes at each end of the yoke b.) Slots along the rear of the yoke that allow for continuous adjustment c.) Holes near the center of the yoke that are directly over the loudspeaker COG.
Figure 5: VB-TILT Vertical Down-Tilt Ranges / Attachment Locations
Vertical Tilt in Degrees
Rear Yok
e Slots
V2-6293458–
89
V2-8333760–
91
V2-26222645–
87
V2-28232643–
83
V2-12273047–88V2-15272945–88V2-32242743–
89
V2-35232539–
89
NOTE: The following specified angles are ach ieved using the yoke mounting hole closest to the end of the
yoke. The yoke must also be oriented with the short 20 degree bend on the rear of the yoke towards the top of the enclosur e.
Loudspeaker
Model
Position A Position B
Adjustment Range
Safety Cable
It is strongly recommended that a safety cable be attached to the loudspeaker using one of the remaining loudsp eaker enclosure rigging points. A 10 mm Shoulder Eyebolt is included in the kit for this pur pose.
CAUTION: Installation of loudspeakers should only be performed by trained and qualified personnel. It is strongly recommended that a licensed and certified professional structural engineer approve the mounting design.
Community Professional Loudspeakers · 333 East Fifth Street, Chester, PA 19013-4511 U.S.A.
Phone (610) 876-3400 · Fax (610) 874-0190 · www.communitypro.com
CMKIT IG 20130123
Loading...