HIGH OUTPUT FULL-RANGE 90° X 60°
R.5-96MAX
WEATHER-RESISTANT LOUDSPEAKER
TECHNICAL SPECIFICATIONS
SYSTEM
Loudspeaker Type: Full-range, two-way, coaxial, weather-resistant
Operating Range1: 70 Hz to 20 kHz (-10 dB)
Frequency Response1: 95 Hz to 20 kHz (-3 dB)
Max Input Ratings:
Maximum Output
Sensitivity (1W / 1m)
Free Space SPL
Nominal Impedance: 8 ohms, 4.8 ohms @ 200 Hz minimum
Nominal Beamwidth (-6dB): 90° x 60°, 1.6 kHz to 10 kHz
Crossover Frequency: 900 Hz
Recommended Processing6: DSP with CONEQ™ power response correction
Recommended Amplier: 1200W to 1800W at 8 ohms
TRANSDUCERS
Low Frequency:
High Frequency: 1 x 1.4" exit compression, 2.87" Voice coil
2
without EQ3:
with EQ4:
Axial Q / DI: 13.8/11.4, 1.6 kHz to 10 kHz
PHYSICAL
Input Connection: 12 foot (3.6 m) SJOW #16 gauge
Enclosure: Rotomolded LLDPE plastic
Finish:
Mounting/Rigging
Provisions:
Environmental: IEC529 IP55W rating with a minimum 5° down-tilt
Dimensions – H x W x D: 16" x 16" x 16.19" (406 x 406 x 411 mm)
Loudspeaker Unit Weight:
Shipping Weight: 51 lbs (23.1 kg)
ACCESSORIES
Pole Mount Bracket: PMB-1RR or PMB-2RR
400W Transformer:
600W RMS, 1200W Program
69 volts RMS, 138 volts momentary peak
130 dB (136 dB Peak)
129 dB (135 dB Peak)
102 dB (125 Hz - 10 kHz)
3,5
:
103 dB (250 Hz - 4 kHz)
1 x 12" inherently weather-resistant cone with
neodymium motor and aluminum demodulation ring
Black, White and Light Grey
(RAL# 9004, 9003, and 7038)
(5) 3/8"-16 rigging points; Steel zinc-rich epoxy
dual-layer powder-coated bracket; Aluminum aiming
strap to secure angle
3-layer Weather-Stop™ with polyester mesh,
Grille:
foam, zinc-rich epoxy dual-layer powder-coated
perforated steel color-matched to enclosure
44 lbs (20 kg) loudspeaker only
47 lbs (21.3 kg) with yoke bracket
External 70V - 400W / 200W / 100W
100V - 400W / 200W
Grille off
Light Grey, Black
and White (standard)
APPLICATIONS
• Stadiums and Arenas
• Racing Tracks
• Theme Parks, Amusement Parks
• Outdoor Entertainment Centers
• Fairgrounds, Rodeos, Air Shows
• Multipurpose outdoor and indoor venues
• Convention Centers
• Portable Sound
Systems
FEATURES
• Low distortion, high quality musicality, excellent speech
intelligibility in a compact enclosure
• High sensitivity, high output (130 dB max)
• Weather-resistant, rotomolded UV resistant enclosure
• Weather-resistant grille and drivers, and moisture-sealed
crossover
• Corrosion-resistant zinc-rich epoxy dual-layer powdercoated steel grille and yoke
• Integral mounting points
• Light Grey, Black and White nish standard
• Five-year product warranty / Fifteen-year enclosure
warranty
DESCRIPTION
The R.5-96MAX is a two-way, full-range loudspeaker
system designed to provide high quality voice and music
reproduction in applications requiring extreme weather
resistance. It is designed to withstand long-term exposure to
tough, environmental conditions and to provide high output
performance.
The R.5-96MAX has a 1.4-inch (36 mm) exit HF compression
driver and a 12-inch (305 mm) cone 600W neodymium LF
driver. The HF assembly is coaxially mounted with the LF
driver allowing 90° x 60° coverage with low distortion. The
system has been designed to provide a at response with
slightly rising HF.
The R.5-96MAX can act as both a musical entertainment
loudspeaker and a voice PA loudspeaker simultaneously.
Each system is backed by Community’s ve-year product
warranty and fteen-year enclosure warranty.
Community strives to improve its products on a continual basis. Specications are therefore subject to change without notice.
R-SERIES • R-MAX
R.5-96MAX
0
10
20
30
Q
Q
70
80
90
100
110
120
10 100 1000 10000
Amplitude(dBSPL)
FrequencyResponse
Resolution>180Hz~ 12Hz,<180Hz~3Hz, 1/6OctaveSmoothing,1W/1m
Degrees
Beamwidth
H‐■ V‐♦
Impedance
MinZ70Hz‐ 16000Hz=4.8Ohms@200Hz
70
80
90
100
110
120
10 100 1000 10000
Amplitude(dBSPL)
Frequency(Hz)
FrequencyResponse(EQ3)
1/6OctaveSmoothing
HIGH OUTPUT FULL-RANGE 90° X 60°
WEATHER-RESISTANT LOUDSPEAKER
FREQUENCY RESPONSE (processed*)
120
110
100
90
Amplitude (dB SPL)
80
70
* Refer to the R-MAX manual for processing details
100 1000 1000010
Frequency (Hz)
IMPEDANCE
40
32
24
Min Z 70 Hz - 16kHz = 4.8 Ohms @ 200 Hz
1/6 Octave Smoothing
FREQUENCY RESPONSE (unprocessed)
120
110
100
90
Amplitude (dB SPL)
80
70
100 1000 1000010
Frequency (Hz)
1/6 Octave Smoothing, 1W/1m
BEAMWIDTH
–n–Horizontal –t–Vertical
100
400
100
16
Degrees
Impedance (Ohms)
8
0
0
100 1000 1000010
Frequency (Hz)
10
100 1,000 10,000
100
1000
Frequency(Hz)
Frequency (Hz)
10000
AXIAL Q
30
20
Q
10
0
100
1000
Frequency (Hz)
10000
NOTES:
1. Operating range and frequency response parameters are stated with DSP
equalization applied.
2. Calculated based on power rating and sensitivity, exclusive of power
compression.
3. Raw driver or system response prior to applying any lters for frequency
response or power response correction.
4. Recommended equalization as published in the Community Loudspeaker Library
within Community's Resyn™ software.
5. Free eld anechoic sensitivity, calculated using input voltage that would produce
1W at the nominal impedance.
6. Community's dSPEC226 loudspeaker signal processor DSP and Resyn™
software include CONEQ™ 1000 point FIR lter power response correction lters
within the precongured speaker le for this model of loudspeaker.
R.5-96MAX
HORIZONTAL POLAR DATA
-6dB
-12dB
-18dB
-24dB
HIGH OUTPUT FULL-RANGE 90° X 60°
WEATHER-RESISTANT LOUDSPEAKER
VERTICAL POLAR DATA
-6dB
-12dB
-18dB
-24dB
NOTE: YOKE MOUNTING HOLE POSITIONS
AND MEASURMENTS MAY HAVE UP TO
A .125" [3MM] TOLERANCE.
R.5-96MAX
DIMENSIONS
HIGH OUTPUT FULL-RANGE 90° X 60°
WEATHER-RESISTANT LOUDSPEAKER
8"
(203 mm)
Center of
Gravity
(405 mm)
Center Line
Top
16 .19"
(411 mm)
15.94"
(5) 3/8"-16
Threaded Inserts
9"
(229 m m)
16"
(406 mm)
10.2 "
(259 mm) typ
2"
(51 m m)
1" (25 mm)
Ø 0.45" (Ø 11.5 mm)
hole x 4
4.63" (117 mm)
16" (406 mm)
16.39 " (416 mm)
8.2" (2 08 mm)
Ø 0.55" (Ø 14 mm) Center only
Yoke Dimensions
0.2" (5 m m)
9" (229 m m)
4.63" (117 mm)
2.75" (70 mm)2.75" (70 mm)
8"
(203 mm)
16"
(406 mm)
Rear
Sides
Center of
Gravity
7.63"
(194 mm)
Center of
Gravity
8"
(203 mm)
Front
ARCHITECTURAL SPECIFICATIONS
The loudspeaker system shall be a two-way, full-range design with one 12-inch (305 mm) high-output LF driver and one 1.4-inch (36 mm) exit HF driver
coaxially mounted to a 90° x 60° molded ABS horn. Drivers shall be connected to an integral crossover with a crossover frequency of 900 Hz. The input
connection shall be one 12' (3.6 m) SJOW #16-gauge cable with stripped ends. The loudspeaker enclosure shall be matte nish rotomolded linear low
density polyethylene providing weather and UV resistance with a 1 mm perforated stainless steel grille backed by water-resistant treated polyester mesh
and open cell foam. The steel grille shall be powder-coated with a proprietary zinc-rich epoxy dual-layer powder-coating process color-matched to the
enclosure. The enclosure shall incorporate ve 3/8"-16 rigging points for multiple mounting options. The system shall have an IEC529 IP rating of IP55W
with a minimum 5-degree downward aiming angle. The system shall have a frequency response of 95 Hz to 20 kHz (-3 dB SPL) and an input capability
of 69V RMS. It shall have a sensitivity of 102 dB (125 hz - 10 kHz) and 103 dB (250 Hz - 4 kHz) at 1W / 1m at 8 ohms nominal impedance. The nominal
dispersion shall be 90°H x 60°V from 1.6 kHz to 10 kHz. The loudspeaker shall be 16 in. (406 mm) H x 16 in. (406 mm) W x 16.19 in. (411 mm) D and weigh
44 lbs (20 kg). A steel yoke that is powder-coated with the same proprietary process, and color-matched, shall be included with the system.
It is strongly recommended that a licensed and certied professional structural engineer approve the mounting design.
CAUTION: Installation of loudspeakers should only be performed by trained and qualied personnel.
Community Professional Loudspeakers, 333 East Fifth Street, Chester, PA 19013-4511 USA
Phone (610) 876-3400 · Fax (610) 874-0190· info@communitypro.com· www.communitypro.com
R.5-96MAX [28AUG13]
Loading...