Community R.35COAXB User Manual
TWO-WAY 10-INCH COAXIAL
R.35COAX
WEATHER-RESISTANT LOUDSPEAKER
TECHNICAL SPECIFICATIONS
SYSTEM
Loudspeaker Type: Full-range, two-way, coaxial, weather-resistant
Operating Range: 70 Hz to 16 kHz (-10 dB)
Frequency Response: 110 Hz to 12.5 kHz (-3 dB)
Max Input Ratings:
Autoformer Taps—70V:
Maximum Output: 120 dB (126dB peak) 122 dB (128dB peak)
Sensitivity (1W / 1m)
Free Space SPL:
Nominal Impedance :
Nominal Beamwidth (-6dB): 90° x 90° , 1.6 kHz to 10 kHz
Axial Q / DI: 10/10, 1.6 kHz to 10 kHz
Crossover Frequency: 1.3 kHz
Recommended High Pass: 70 Hz 24 dB / Octave
Recommended Amplier : 400W to 600W at 8 ohms
COAX IAL TRANSDUCERS
Low Frequency: 1 x 10" Carbon ring NeverWet™* treated cone, 2" VC
High Frequency: 1 x 1.25" exit compression
PHYSICAL
Input Connection:
Controls: Music / speech switch, 70V/100V operation jumper
Enclosure: ABS plastic, matte nish, paintable
Finish:
Mounting/Rigging
Provisions:
Input Panel Weather Cover:
Environmental:
Dimensions – H x W x D: 11" x 13" x 13.5" (279 x 330 x 343 mm)
Loudspeaker Unit Weight: 26 lbs (11.8 kg) with included yoke
Shipping Weight: 32 lbs (14.5 kg)
ACCESSORIES
Vari-Tilt™ Yoke:
Full Rotation Yoke:
NOTE: All wattage gures are calculated using the rated impedance.
* NeverWet is a registered trademark of NeverWet, LLC.
Community strives to improve its products on a continual basis. Specications are therefore subject to change without notice.
200W RMS, 400W Program
40 volts RMS, 80 volts momentary peak
200W, 100W, 50W, 25W and low impedance
100V:
200W, 100W, 50W
MUSIC SPEECH
97 dB (125 Hz - 10 kHz)
97 dB (250 Hz - 4 kHz)
8 ohms, 5.9 ohms
@ 200 Hz minimum
NL4 Speakon-type connector for low impedance
operation only; and 7-position terminal strip for low
impedance or constant voltage operation
Light Grey, Black or White (standard)
RAL # 7038, 9004 or 9003
Two M8 rigging points, zinc-rich epoxy dual-layer
powder-coated yoke, included integral safety cable
mounting point
3-layer Weather-Stop™ featuring NeverWet™ treated
Grille:
polyester mesh, foam, zinc-rich dual-layer powder-
coated perforated steel color-matched to enclosure
Color-matched ABS plastic with 13.5mm ID gland nut
installed in .82" knockout
IP55W per IEC 529 at recommended 5° down-tilt,
designed to MIL-STD-810G
R-VTY35. Provides pan-tilt aiming functions. Zinc-rich
epoxy dual-layer powder-coated steel with SS
hardware, color-matched to loudspeaker.
R-FRY35. Provides full rotation mounting capability
for down-ring application (i.e. top of press box). Zinc-
rich epoxy dual-layer powder-coated steel with SS
hardware, color-matched to loudspeaker.
99 dB (125 Hz - 10 kHz)
99 dB (250 Hz - 4 kHz)
8 ohms, 5.5 ohms
@ 5 kHz minimum
Shown with grille removed
Available in Light Grey,
Black or White (standard)
APPLICATIONS
• Theme and Amusement Parks
• Outdoor Entertainment Centers
• Malls, Fairgrounds, Race Tracks
• Multipurpose Indoor/Outdoor Venues
• Stadiums and Arenas
• Swimming pools
• Athletic Fields
• Convention Centers
• Cruise Ships
• Factories
FEATURES
• Excellent musicality and intelligibility, low distortion, and
high sensitivity and output
• Weather-resistant, compact, matte nish paintable high
impact ABS plastic modied-trapezoidal enclosure
• NeverWet™ treated grille and LF driver cones, polymer
HF diaphragm, and moisture-sealed crossover
• Corrosion-resistant zinc-rich epoxy dual-layer powder-
coated steel grille and low-prole yoke
• Real compression driver on Tru-Phase™ waveguide
• 200W Autoformer (standard)
• Structurally rigid with weather sealed wood inserts to
reduce resonance and rear radiation
• Light Grey, Black and White nish standard - Custom
colors available upon request.
• Five-year product warranty / Fifteen-year enclosure
warranty
DESCRIPTION
The R.35COAX is a two-way, full-range loudspeaker
system designed to provide high quality voice and music
reproduction in applications requiring extreme weather
resistance. It is designed to withstand long-term exposure to
tough, environmental conditions and to provide performance
normally associated only with indoor loudspeakers. The
R.35COAX has a 1.25-inch (32mm) exit HF compression
driver and a 10-inch (254mm) cone LF driver with a 2-inch
voice coil. The HF assembly is coaxially mounted with the
LF driver allowing 90° conical coverage with low distortion.
The carbon ring cone design provides a cone area nearly
equivalent to a typical 12-inch driver cone.
The Music / Voice switch provides an out-of-the-box selectable
at response or 3dB boost for increased vocal intelligibilty
allowing for additional application exibility. The design uses
Community's proprietary Tru-Phase™ phase plug to provide
wide dispersion, low distortion and increased intelligibility. The
LF driver cone is treated with the same NeverWet™ protection
as the grille cloth to provide full weather-resistance. Enclosure
has a reinforced ribbed interior with weather-treated wooden
inserts to reduce resonance, increase rigidity and reduce rear
and lateral radiation.
R-SERIES
70
80
90
100
110
120
10 100 1000 10000
Amplitude (dB SPL)
Frequency Response
12Hz Resolution, 1/6 Octave Smoothing, 1W/1m 12Hz Resolution, 1/6 Octave Smoothing, 1W/1m
0
8
16
24
32
40
48
Impedance (Ohms)
Impedance
Min Z 30 Hz - 16000 Hz = 5.5 Ohms @ 5000 Hz
30
100 1,000 10,000
Q
Q (Music Switch)
10
100
100 1,000 10 ,000
Degrees
Beamwidth (Music Switch)
H-■ V-♦ H-■ V-♦
R.35COAX
TWO-WAY 10-INCH COAXIAL
WEATHER-RESISTANT LOUDSPEAKER
FREQUENCY RESPONSE IMPEDANCE
— Music, - - Speech, 12 Hz Resolution, 1/6 Octave Smoothing, 1W/1m
Ohms
Amplitude (dB SPL)
Frequency (Hz)
10
BEAMWIDTH - MUSIC AXIAL Q - MUSIC
400
100
Degrees
10
100
1000 10000
Frequency (Hz)
–n–Horizontal –t–Vertical
20
Q
10
0
100 1000 10000
DIMENSIONS
0.84" (21mm)
6.06" (15 4m m)
13.5" (343mm)
Center of
Gravity
8. 22" (209 mm)
Ø 0.35" (Ø 9mm)
8 places
2.6" (66mm)
4.65" (118mm)
— Music, - - Speech, Min Z 30 Hz - 16kHz = 5.5 Ohms @ 5kHz
100
Frequency (Hz)
Q
Frequency (Hz)
1000 10000
12.12" (30 8mm)
Ø 0.51" (Ø 13mm)
1.58" (40mm)
0.98" (25mm)
2.6" (66mm)
4.65" (118mm)
1" (25mm)
13" (330mm)
Top
Center of
Load
Center of
11" (27 9 m m)
Gravity
Front
ARCHITECTURAL SPECIFICATIONS
The loudspeaker system shall be a two-way, full-range modied trapezoidal design with one 10-inch (254mm) high-output LF driver and one 1.25-inch
(32mm) exit HF driver mounted coaxially. Drivers shall be connected to an integral crossover with a crossover frequency of 1.3 kHz. The input connections
shall be an NL4-type connector and a 7-position terminal strip for standard or autoformer tap operation. There is also a 2-position switch for voice or music
applications. The loudspeaker enclosure shall be matte nish high impact ABS plastic with a 1mm perforated steel grille backed by NeverWet™ treated
polyester mesh and open cell foam. There shall be two M8 rigging points, and an included steel dual-layer powder-coated mounting yoke. Integrated
ribbing and weather-sealed wooden inserts provide added structural support and reduce rear and lateral radiation. The system shall have a frequency
response of 110 Hz to 12.5 kHz (-3 dB SPL) and an input capability of 40V RMS. At the music setting, it shall have a sensitivity at 1W / 1m, 8 ohms nominal
impedance, of 97 dB (125 Hz - 10 kHz) and 97 dB (250 Hz - 4 kHz). At the voice setting, it shall have a sensitivity at 1W / 1m, 8 ohms nominal impedance,
of 99 dB (125 Hz - 10 kHz) and 99 dB (250 Hz - 4 kHz). The nominal dispersion shall be 90° H x 90° V from 1.6 kHz to 10 kHz. The loudspeaker shall be
11" (279mm) H (front) x 13" (330mm) W x 13.5" (343mm) D and shall weigh 26 lbs (11.8 kg) with the included mounting yoke.
CAUTION: Installation of loudspeakers should only be performed by trained and qualied personnel.
It is strongly recommended that a licensed and certied professional structural engineer approve the mounting design.
Community Professional Loudspeakers, 333 East Fifth Street, Chester, PA 19013-4511 USA
Phone (610) 876-3400 · Fax (610) 874-0190· info@communitypro.com· www.communitypro.com
Yoke Hole Dimensions
3.17 " (81mm )
M8 Hang Point /
Center of Gravity
8. 54" (217m m)
5.5" (140mm)
Sides
R.35COA X [15AUG2013]
Loading...