Community IUB0002WRG Users Manual

I SERIES

BalancePoint™ Flyware

For Point Source and
Subwoofer loudspeakers
models IP8, IP6, IS8, and IS6

IUB1122WRG
IUB1152WRG
IUB1153WRG

IUB0002WRG

IUB112SWRG

The BalancePoint™ Flyware Accessory Guide (a complete set of instructions for all
of the BalancePoint™ Flyware Kits) is available on the Community website.

Community Professional Loudspeakers

333 East Fifth Street, Chester, PA 19013-4511 USA
Phone [phone] • Fax [phone]
communitypro.com • [e-mail]

U-Brackets for the weather-resistant

IP6/8-1122WR, IP6/8-1152WR,

IP8-1153WR, IP8-1151WR, IP8-0002WR,

IS6/8-112WR, IS6/8-115WR, IS6/8-118WR,

IS6/8-212WR, IS6/8-215WR, IS6/8-218WR

CAUTION: Installation of loudspeakers should only be
performed by trained and qualified personnel. It is strongly
recommended that a licensed and certified professional
structural engineer approve the mounting design.

IMPORTANT SAFETY INSTRUCTIONS

Always follow these basic safety precautions when using or installing I SERIES loudspeakers and
accessories:

• Read these instructions prior to assembly.

• Keep these instructions for reference.

• Heed all warnings.

• Follow all instructions, particularly those pertaining to rigging, mounting, hanging and electrical
connections.

• Do not use this apparatus near water.

• Clean only with dry cloth.

• Do not block any ventilation openings. Install in accordance with the manufacturer’s instruction.

• Do not install near any heat sources such as radiators, heat registers, stoves,light fixtures, or
other apparatus (including amplifiers) that produce heat.

• Only use attachments and accessories that are specified and approved by the manufacturer.

Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been
damaged in any way, such as liquid has been spilled or objects have fallen into the apparatus, the
apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.

The terms CAUTION, WARNING, and DANGER may be used in this manual to alert the reader to
important safety considerations. If you have any questions or do not understand the meaning
of these terms, do not proceed with installation. Contact your local dealer, distributor, or call
Community directly for assistance. These terms are defined as:

CAUTION: describes an operating condition or user action that may expose the
equipment or user to potential damage or danger.

WARNING: describes an operating condition or user action that will likely cause damage
to the equipment or injury to the user or to others in the vicinity.

DANGER: describes an operating condition or user action that will immediately damage
the equipment and/or be extremely dangerous or life threatening to the user or to others
in the vicinity.

These installation instructions are for use by qualified personnel only. To reduce the risk of fire or
electric shock do not perform any servicing other than that contained in the operating instructions
unless you are qualified to do so.

UNPACKING / INSPECTION

Community I SERIES loudspeakers are
engineered and manufactured to be rugged
and they are carefully packed in sturdy cartons.
However, it is recommended to thoroughly
inspect each unit after it has been removed from
the packaging, as damage could occur during
shipping.

Please note that once the shipment has left
your dealer or the Community factory, the
responsibility for damage is always borne by
the freight company. If damage has occurred
during shipping, you must file a claim directly
with the freight company. It’s very important to
contact the freight company as soon as possible
after receiving your shipment, as most freight
companies have a short time limit within which
they will investigate claims. Make sure to save
the carton and the packing material, as most
claims will be denied if these materials are
not retained. Your Community dealer and the
factory will try to help in any way they can, but
it is the responsibility of the party receiving the
shipment to file the damage claim.

It is always a good idea to retain the carton and
packing materials, if possible, in the event that
the unit may need to be returned to your dealer
or distributor for repair in the future.

CAUTION: Installation of
I SERIES loudspeakers should

only be performed by trained
and qualified personnel. It is strongly
recommended that a licensed and
certified professional structural
engineer approve the mounting. Severe
injury and/or loss of life may occur if
this product is improperly installed.

RIGGING SAFETY / IMPORTANT NOTES

There are three primary areas of responsibility
for rigging loudspeakers. The first is the
building structure. Always consult with the
building architect or structural engineer to
assure the ability of the structure to support
the loudspeaker system. The second area
of responsibility is the loudspeaker itself.
Community certifies its loudspeaker systems
and rigging accessories for suspension
when they are properly installed according
to our published guidelines. The third area
of responsibility is everything between the
loudspeaker and the building structure and the
actual process of installation. The installing
contractor assumes this responsibility.
Loudspeaker rigging should be performed only
by certified rigging professionals using certified
rigging hardware chosen for the specific
application. Prior to installation, the contractor
should present a rigging plan, with drawing
and detailed parts list, to a licensed structural
engineer (P.E.) or architect for written approval.

Page 2 BalancePoint™ Flyware I SERIES

IMPORTANT: I SERIES loudspeakers are designed and intended to be mounted to
diering building surfaces using a variety of rigging hardware, means and methods.
Installation of loudspeakers should only be performed by trained and qualified
personnel. All electrical connections must conform to applicable city, county, state, and
national (NEC) electrical codes.

DANGER: All rigging fittings must be fully tightened and secured. Any missing fasteners
or parts will compromise the structural integrity of the enclosure and constitute a safety
hazard. Over-tightening (crushing the wood) should be avoided as well. Do not suspend
the loudspeaker unless all fasteners are securely in place!

IMPORTANT: The flat head bolts that come installed in each enclosure must remain in
place or be replaced by a threaded fastener from an array bracket. The bolts attach to
internal metal brackets that are critical to the structural integrity and rated Safe Working
Load (SWL) of each point and each array assembly. Failure to include a fastener in every
location could lead to serious injury, or even death.

DANGER: I SERIES rigging fittings are rated at a Working Load Limit (WLL) of 150 lbs
(68 kg) with a 10:1 safety margin. No single rigging fitting should ever be subjected to a
load that is greater than this stated limit. Failure to heed this warning could result in
injury or death!

DANGER: No more than three (3) full-range and two (2) subwoofers should be on any
single connected configuration. Do not exceed the Safe Working Load (500 lbs [226.8 kg])
of the assembly. Loudspeaker weights are provided on the last page of this manual.

U-BRACKETS

IUB1122WRG - U-Bracket for IP6/8-1122WR, IS6/8-212WR
IUB1152WRG - U-Bracket for IP6/8-1152WR
IUB1153WRG - U-Bracket for IP8-1153WR, IS6/8-215WR,

IS6/8-218WR

IUB0002WRG - U-Bracket for IP8-1151WR, IP8-0002WR,

IS6/8-115WR, IS6/8-118WR

IUB112SWRG - U-Bracket for IS6/8-112WR

APPLICATION: Mount and aim single loudspeakers from ceilings, walls, trusses,
floors, etc in portrait or landscape orientation.

IUB-1122WRG
on an IP8 -1122W R

Before assembly: Adhere the rubber washers to the inside of the yoke (aligned
with cabinet mounting points).

Note: The yoke can be attached to the building structure and then the
loudspeaker can be installed later.

Parts:

Trapezoid Cabinet Installation (IP6/8)
or Center Point Subwoofer Connection (IS6/8)

UB

UB: U-Bracket

Hardware:

Qty

Code Description

4 HH1-4 10 x 40 mm Hex Hd Bolts

4 HW1 10 mm Flat Washers

4 HL1 10 mm Lock Washers

4 HW8-4

2 HS6 6 x 35 mm Socket Hd Bolts

2 HW6 6 mm Flat Washers

2 HL6 6 mm Lock Washers

2 HW.25

IMPORTANT: The WR U-brackets can only be
used with I SERIES WR models.

Kit Weights:

IUB1122WRG: 16.0 lb (7.3 kg)
IUB1152WRG: 17.0 lb (7.7 kg)
IUB1153WRG: 22.0 lb (10.0 kg)
IUB0002WRG: 17.0 lb (7.7kg)
IUB112SWRG: 10.0 lb (4.5 kg)

8mm ID x 40mm OD
Black Rubber Washer

1/4" ID x 5/8" OD
Black Rubber Washer

1

UB

HS6

HH1-4

HL1

HW1

HW8-4

HW.25

Figure 1. Remove middle cabinet bolts and attach yoke to cabinet

HL6

HW6

IUB-0002WRG
on an IS6 -115WR

Mounting Detail

2

Fully tighten all
connections

I SERIES BalancePoint™ Flyware Page 3