Commercial Electric 5623-WH User Manual
Item #1001863164
ETL LISTED
AN/CSA STD. C22.2#42.1:200-1
Model #5623-WH
Installation Guide
Flat Panel TV Cable Organizer Kit
PACKAGE CONTENTS
A - Pre-Assembled Top Plate w/ 15 A/125 V duplex receptacle,
8 ft 14/2 with ground pre-stripped electrical building wire
and attached mounting wings
B - Bottom Plate with easy push-in connectors and attached
mounting wings
C - 6 ft. extension cord w/ 360˚ rotating at head
D - Electrical box
TOOLS NEEDED
Drywall saw
Tape measure
Phillips head screwdriver
Pencil
Level
Stud Finder
Tape
CAUTION
Intended for use on 15 amp branch circuits
Not intended for use in drywall with re
walls
On outside exterior walls with insulation
push away insulation to allow proper
mounting
For video information visit homedepot.com and search SKU 1001863164 or model number 5623-WH
Installation
1
PREPARING THE WALL FOR INSTALLATION
Determine the top and bottom plate location*
□
□
Use the stud nder to center between the wall framing
studs.
□
Be sure to frame your plate both vertically and
horizontally
2
Using the template supplied, trace the opening for both the top and
□
bottom plate on the wall. Remember, the plates are designed to be
mounted centered between the studs.
Scan Me
Up to 7’
Outlet
Height or
18”
*This kit is designed for standard 2x4 framed walls. If your wall
does not have the standard 3.5” spacing between the drywall
you will need to use a kit that mounts on the front of the wall.
Up to 6’
TEMPLATE
TIP: Loop a piece of tape with the sticky side outward to form a circle and
apply it to the back of the template to secure it to the wall.
CUT DRYWALL FOR TOP AND BOTTOM PLATES
3
□
With your template secured to the wall with the tape, using a drywall saw,
cut a hole in the drywall the size of each template
3026001
Both top and bottom plates are installed between the same two
studs.
Page 1 of 4
CONFORMS TO
UL STD. 498
CERTIFIED TO
C
RoHS Compliant
This product is patent protected by
U.S. Patent number: 7390964B2, 7399920B2,
D553475S, D554475S and D568719S
Installation
ETL LISTED
AN/CSA STD. C22.2#42.1:200-1
4
RUN CABLES THROUGH WALL
□
Run your low voltage cables and the included 14/2 with ground UL
approved electrical building wire from the top opening in the wall
through the bottom opening in the wall. TIP: Straighten out the
cable from the top plate BEFORE running the cable through the wall.
You will need to sh the cables from the top opening to the bottom
opening. (For exterior walls as you may need to use the Commercial
Electricft Mini Cable Snake) BEFORE installing the top power plate
into the top template opening, make sure to pull your low voltage
cables through the low voltage cable opening at the back of the
plate.
Item #1001863164
Model #5623-WH
Installation Guide
Flat Panel TV Cable Organizer Kit
5
INSTALLING THE TOP PLATE
After inserting your low voltage cables and the electrical building wire
□
through the opening for the top plate (A), insert the top plate (A) into the
wall by inserting the electrical work box into the wall rst. Slowly slide
the top power plate (A) into the opening. Swing the top of the plate into
position until the entire plate is ush against the wall. Using a Phillips
head screwdriver, tighten the screws with wings. These wings fasten
tightly against the back of the drywall. Do not overtighten screws.
A
Installation of Electrical Connectors
6
□
Now that you have pulled the top power outlet plate’s electrical building wire
through the bottom hole on the wall, bend the wire straight. Break the tab on
the back of the white old work box (D) and push the stripped end of the
wire through the opening. Insert the stripped end of the wires into the push-in
connectors. First, insert the stripped black wire into the open side of the push-in
connector with the black wire – be sure to push the stripped black wire
completely into the connector. Insert the stripped white wire into the open
side of the push-in connector with the white wire. Next, insert the bare copper
ground wire into the open side of the push-in connector with the green ground
wire. Push all of the wires and the push-in connectors into the white old work
box. Screw the white old work box to the back of the bottom plate (B).
A
Wall Opening
Connect Here
Electrical Wire
B
D
3026001
Do not plug in the supplied 6ft. extension cord until the installation of the
wallplates are completed.
Page 2 of 4
CONFORMS TO
UL STD. 498
CERTIFIED TO
C
RoHS Compliant
This product is patent protected by
U.S. Patent number: 7390964B2, 7399920B2,
D553475S, D554475S and D568719S
Loading...