Page 1
S630MA Quick Installation Chart
For your convenience, this chart lists all the CPUs supported by S630MA and their corresponding jumper
setting.
*** The Ratio of some latest CPUs are fixed by Intel, such as Celeron/ Celeron-II/ Pentium-III 366, 400, 566…
etc. You can ignore the four jumpers if you have this CPU on board and it will be auto detected by
motherboard. Please check with the CPU manufacturer or vendor for the CPU Ratio information.
Ratio JF0 JF1 JF2 JF3
3.0x 2-3 2-3 2-3 1-2
3.5x 2-3 1-2 2-3 1-2
4.0x 2-3 2-3 1-2 2-3
4.5x 2-3 1-2 1-2 2-3
5.0x 2-3 2-3 1-2 1-2
5.5x 2-3 1-2 1-2 1-2
6.0x 1-2 2-3 2-3 2-3
6.5x 1-2 1-2 2-3 2-3
7.0x 1-2 2-3 2-3 1-2
7.5x 1-2 1-2 2-3 1-2
8.0x 1-2 2-3 1-2 2-3
S630MA
Motherboard
User's Manual
Product Name: S630MA
Manual Revision: English, 1.0
Trademarks
Intel, Celeron , Socket 370 and Pentium III are trademarks of Intel Corporation
Page 2
SiS is a registered trademark of Silicon Integrated Systems Corp.
Award is a trademark of Award Software International Inc.
MS-DOS, Windows 95, Windows 98, Windows 2000 and Windows NT are registered trademarks of Microsoft
Corporation
Novell is a trademark of Novell Corporation
ADI is a trademarks of Analog Devices Inc.,
All other brand and product names are trademarks or registered trademarks of their respective companies.
Table of Contents
Chapter 1. Introduction
1.1 Product Overview
1.2 Features
1.3 Specifications
1.4 Content
1.5 System Board Layout
Chapter 2. Hardware Setup
2.1 Installation Procedure
2.1.1 Jumper Settings
2.1.2 Clearing the CMOS
2.1.3 CPU FSB Frequency Selection
2.1.4 CPU Voltage Setting
2.1.5 CPU Frequency Setting
2.2 Installation of CPU
2.3 Installation of Memory
2.3.1 Installation of 168-pin DIMM
2.3.2 Removal of 168-pin DIMM
2.3.3 Memory Configuration
2.4 I/O Connections/Panel Connections
2.4.1 ATX Power Connector
2.4.2 Chassis and CPU Fan Connector
2.4.3 Infrared Connector
2.4.4 Floppy Disk Drive Connector
2.4.5 Primary/Secondary IDE Connector
2.4.6 PS/2 Mouse Port
2.4.7 PS/2 Keyboard Connector
2.4.8 VGA Output Connector
2.4.9 Serial Port
2.4.10 LAN Connector
2.4.11 Printer Port
2.4.12 USB Connectors
2.4.13 Game/MIDI/Line Out/Line In/Mic In Connector (optional)
2.4.14 Line Out Connector
2.4.15 Line In Connector
2.4.16 Microphone In Connector
2.4.17 Game/MIDI Port
2.4.18 ATAPI IDE/SONY Audio
2.4.19 Panel Connection
Chapter 3. BIOS Setup
3.1 CMOS Setup Utility
3.2 Standard CMOS Setup
3.3 Advanced BIOS Features Setup
3.4 Advanced Chipset Features Setup
3.5 Integrated Peripherals
3.6 Power Management Setup
3.7 PNP/PCI Configuration Setup
3.8 PC Health Status
3.9 Frequency Control
3.10 Load Fail-Safe Defaults
3.11 Load Optimized Defaults
Page 3
3.12 Set Password
3.13 Save & Exit Setup
3.14 Exit Without Saving
Chapter 4. Software Installation
4.1 Installing the Sound Driver
4.1.1 For Windows 95/98
4.1.2 For Windows 2000/NT 4.0
4.2 Installing the LAN Driver
4.2.1 For Windows 95/98/2000
4.2.2 For Windows NT 4.0
4.2.3 The other Operation Systems
4.3 Installing the Graphics Driver
4.3.1 Windows 95/98 Installation
4.3.2 Windows 2000 Installation
4.3.3 Windows NT 4.0 Installation
Chapter 1. Introduction
1.1 Product Overview
Thank you for purchasing the S630MA motherboard. This motherboard uses SiS 630E Host Interface
Controller, 2D/3D Ultra-AGP with super south single chipset. We have conducted a motherboard
compatibility test with a variety of hardware and software, such as CPUs, memory, display cards, CD ROMs,
Novell, MS Office ....etc and compliance with Year 2000.
We have set high standards on our quality control, with absolute confidence, we believe this product is the
wisest choice.
This manual is composed of four sections. The first section is the introduction of this motherboard, and the
second section explains the proper procedure to setup the motherboard, the third section provides
information on how to setup the CMOS. The last section is the installation of the device drivers & utilities.
1.2 Features
Support Ultra DMA 66.
Modem Remote Ring On.
Support NCR SCSI BIOS.
Support Hardware Monitor function.
Support 66/100/133MHz FSB frequency.
ADI AD1881A Audio CODEC on board
Support Advanced Configuration Power Interface (ACPI).
Support Desktop Management Interface (DMI) through BIOS.
Integrated 2D/3D graphics accelerator with AGP 4X performance.
RTC Wake up Alarm: Program the date/time to wake up your system.
Integrated Fast Ethernet Controller with 10/100Mbps and wake up on LAN.
Both the BIOS and hardware levels of the motherboard meet PC '99 compliant.
1.3 Specifications
CPU :
Supports Intel Socket 370 Celeron or Pentium III Processor in the Plastic Pin Grid Array (PPGA) or
Flip-Chip PGA package with 66/100/133MHz Front Side Bus.
Chipset :
SiS 630E
VGA :
Integrates the UltraAGP technology and advanced 128-bit graphic display interface.
AGP v2.0 compliant. Delivers AGP 4x performance and up to 2 GB/s memory bandwidth.
Integrated 24-bit 270MHz RAMDAC graphics controller.
Page 4
Full 2D/3D/DirectX acceleration.
Supports hardware DVD Accelerator.
Shared System Memory Area up to 64MB.
LAN :
Integrated 10/100Mb Fast Ethernet Controller.
Full Duplex and Half Duplex Mode for both 10 and 100 Mbps.
Plug and Play Compatible.
High performance 32bit PCI Bus Master Architecture with integrated direct memory.
IEEE 802.3 and 802.3u standard compatible.
IEEE 802.3u auto negotiation and parallel detection for automatic speed selection.
Power down of 10base-T/100base-Tx sections when not in use.
DIMM :
Supports 3.3V PC100/133-compliant SDRAM in 2 168-pin banks, each bank consists of 1x168-pin
64-bit DIMM socket, which can support memory sizes of 16/32/64/128/256/512 MB modules.
System memory Size up to 1GB.
ATX Power :
Supports Modem remote Ring-On function
Supports software power off function
Supports RTC Wake-Up.
Supports Wake up on LAN.
IDE :
Dual channel PIO and PCI Bus Master IDE ports support up to 4 EIDE devices for HDD or CD-ROM.
Supports PIO Mode 4.
Supports Multiword DMA Mode 0, 1, 2.
Supports Ultra DMA 33/66 with data transfer rate up to 33/66 MB/Sec.
BIOS :
2Mbits Award BIOS v6.00PG with built-in Anti-Virus, DMI, ACPI support, and green function (Plugand-Play BIOS)
Supports CD-ROM/HD/SCSI/Floppy/LS120/ZIP and LAN boot up
Supports NCR SCSI BIOS.
I/O Devices :
One FDD control port supports two of the 5.25" or 3.5" floppy drives up to 2.88 MB.
Two high-speed 16550 UART compatible serial ports
One parallel ports with ECP/ EPP compatibility.
One PS/2 mouse port
One PS/2 Keyboard connector
USB Ports :
Five Universal Serial Bus (USB) ports support up to 127 peripheral devices. (Cable optional)
Delivers better connectivity and 2*12Mb bandwidth
Sound :
ADI AD1881A Audio Codec
AC '97 Rev 2.1 compliant
16-bit Stereo Full-Duplex Codex
High quality Sample Rate Conversion (SRC) from 7kHz to 48kHz in 1Hz increments
Phat Stereo 3D Stereo Enhancement
Page 5
Audio Amp Power Down Signal
Extended 6-bit Master Volume Control
DSP 16-bit Serial Port Format, Slot 16 Mode
Split Power Supplies ( 3.3V Digital / 5V Analog )
IR Port :
One IrDA/ASKIR compatible Infrared interface port. (Cable optional)
Expansion Slots:
Three 32-bit PCI expansion slots
One Audio Modem Riser (AMR ) slot
Operating System :
Supports Windows 3.x/95/98/2000, Windows NT, MS-DOS V6.22, OS/2, Novell, Unix, SCO UNIX.....
Dimension :
234 mm x 170 mm Micro ATX form factor
1.4 Content
The motherboard box contains the following items:
One Motherboard
One IDE Ribbon Cable
One Floppy Ribbon Cable
One Serial Ribbon Cable
One Driver CD
User's Manual & Quick Installation Chart
1.5 MotherBoard Layout
Page 6
Chapter 2. Hardware Setup
2.1 Installation Procedure
1. Jumper settings
2. Installation of CPU
3. Installation of Memory
4. I/O Connections & Panel Connections
2.1.1 Jumper Settings
In this manual, (1-2) represents the first and second pins of the jumper. (2-3) represents the
second and third pins of the jumper. On the motherboard, you will see two sets of jumpers with
different color jumper caps:
Yellow Jumper Caps : Sets the Function of Flash CMOS JRTC
Green Jumper Caps : Sets the type and speed of CPU JF0, JF1, JF2, JF3
Red Jumper Caps : Sets the FSB frequency of CPU JFSB0, JFSB1
WARNING:
Electronic parts are Static sensitive. To prevent damage to the computer and its parts
please take the following measures.
Work on a surface such as concrete, linoleum or hard wood floor.
Page 7
Ground your self with either a properly installed grounding strap or by touching a major
electrical appliance long enough to discharge the static.
2.1.2 Clearing the CMOS (Yellow Jumper Cap)
JRTC: CMOS Function Selection
1-2 : Clear data
2-3 : Normal Operation (Default Setting)
How to Clear the CMOS Setting
1. Turn off the power.
2. Remove ATX power cable from power connector.
3. Remove Yellow Jumper Cap from JRTC (2-3) and put on JRTC (1-2) to remove the CMOS setting.
4. Remove Yellow Jumper Cap from JRTC (1-2) and put on JRTC (2-3).
5. Connect ATX power cable back to power connector.
6. Turn on the power.
7. While the system reboots, press <DEL> key to set the BIOS setup.
2.1.3 CPU FSB Frequency Setting (Red Jumper Caps)
The JFSB jumper provides FSB frequency settings for the CPU. Auto Detect, 66MHz, 100MHz or 133MHz FSB
frequency can be selected with this jumper. The over specification operation is not recommended.
2.1.4 CPU Voltage Setting
The motherboard supports CPU VID function, the CPU core voltage is automatically detected, the range is from
1.3V to 3.5V for Pentium III CPU and. the range is from 1.3V to 2.0V for Celeron & Socket 370 CPU.
2.1.5 CPU Frequency Selection (Green Jumper Caps)
Ratio JF0 JF1 JF2 JF3
3.0x 2-3 2-3 2-3 1-2
3.5x 2-3 1-2 2-3 1-2
4.0x 2-3 2-3 1-2 2-3
4.5x 2-3 1-2 1-2 2-3
5.0x 2-3 2-3 1-2 1-2
Page 8
5.5x 2-3 1-2 1-2 1-2
6.0x 1-2 2-3 2-3 2-3
6.5x 1-2 1-2 2-3 2-3
7.0x 1-2 2-3 2-3 1-2
7.5x 1-2 1-2 2-3 1-2
8.0x 1-2 2-3 1-2 2-3
The Ratio of some latest CPUs are fixed by Intel, such as Celeron/ Celeron-II/ Pentium-III 366, 400, 566… etc.
You can ignore the four jumpers if you have this CPU on board and it will be auto detected by motherboard.
Please check with the CPU manufacturer or vendor for the CPU Ratio information.
2.2 Installation of CPU
Before installing CPU, make sure the power is off. Locate the level bar on the PGA370 ZIF socket. Push level bar away
from the socket and pull upward 90 degrees. Insert the CPU into the socket. Make sure the notch of the CPU
corresponds with the white dot on the ZIF socket (the corner without pin socket). Do not push in the CPU. Make sure
all pins are aligned with the CPU socket. ON the level bar.
2.3 Installation of Memory
This motherboard has 2x168-pin 64-bit Dual Inline Memory Module (DIMM) sockets divided into 2 banks. You can
install 3.3V Unbuffered PC100/133-compliant Synchronous DRAM (SDRAM) memory.
Some DIMM memory have SPD ( Serial Presence Detect ) 8-pin IC on module. It is not recommended the SPD (
Serial Presence Detect ) DIMM blends and non-SPD DIMM.
2.3.1 Installation of 168-pin DIMM (Dual Inline Memory Module)
1. Before inserting the DIMM, make sure the pin1 of the DIMM matches with the pin1 on the DIMM socket.
2. Insert DIMM into the DIMM sockets at a 90-degree angle and press down.
2.3.2 Removal of 168-pin DIMM
1. Press the holding clips on both sides of the socket outward to release the DIMM.
2. Gently pull the DIMM out of the socket.
2.3.3 Memory Configuration
There is no jumper setting required for the memory size or type. It is automatically detected by the system BIOS,
and the total memory size is to add them together.
DIMM Socket DIMM Modules
DIMM1
PC100/133 SDRAM 16, 32, 64, 128, 256, 512MB
DIMM2 PC100/133 SDRAM 16, 32, 64, 128, 256, 512MB
2.4 I/O Connections/Panel Connections
I/O Connections
Page 9
ATXPWR ATX Power Connector
CPUFAN CPU fan connector
SYSFAN Chassis fan connector
JIR Infrared Connector ( Cable optional )
FLOPPY Floppy Disk Drive Connector
IDE1, 2 Primary/ Secondary IDE Connectors
MS PS/2 Mouse Port
KB PS/2 Keyboard Connector
VGA VGA output Connector
COM1,COM2 Serial Ports 1 & 2
LPT Printer Port
USB USB Connector
LAN LAN Connector
GP1 Game/MIDI Connectors
LINE_OUT Line out Connector
LINE_IN Line in Connector
MIC Microphone in Connector
SONY The Connector for IDE/Sony CD-ROM audio in
2.4.1 ATX Power Connector (20-pin ATXPWR)
Make sure that the power supply is off before connecting or disconnecting the power cable.
2.4.2 CPU, Chassis Fan Connector (3-pin CPUFAN, SYSFAN)
Connect the fan's plug to the board taking into consideration the polarity of the connector.
2.4.3 Infrared Connector (10-pin JIR)
This connector supports the optional wireless transmitting and receiving infrared module, with this module and
application software such as Laplink or Win95 Direct Cable Connection, user can transfer files to or from their
laptops, notebooks, PDA, PCs and printers. The connector supports IrDA (115.2Kbps, 2 meters) and ASK-IR
(56Kbps). An optional consumer infrared (CIR) set connects to the CIR and SIR connectors simultaneously for
both wireless transmitting and remote control functions through one external infrared module. Install infrared
Page 10
module onto Infrared connector and configure the setting through "UART Mode Select" in Integrated Peripherals
to select whether UART is directed for use with COM2 or Infrared.
2.4.4 Floppy Disk Drive Connector (34-pin FLOPPY)
This connector supports the provided floppy disk drive ribbon cable. Orient the red stripe to pin 1
2.4.5 Primary/Secondary IDE Connector (Two 40-pin IDE)
These connectors support the provided IDE hard disk ribbon cable. Connect your first IDE hard disk to master
mode of the primary channel. If you have second IDE device to install in your system, connect it as slave mode on
the same channel, and the third and fourth device can be connected on secondary channel as master and slave mode
respectively.
There are three connectors on the 80-pin IDE ribbon cable. The blue connector must connect with
motherboard's IDE connector and the other connectors must connect with HDD. In order to get the better
performance the Ultra DMA 66 HDD must connect with 80-pin IDE ribbon cable.
2.4.6 PS/2 Mouse Port (6-pin Mini-Din MS)
The system will direct IRQ12 to the PS/2 mouse.
Page 11
2.4.7 PS/2 Keyboard Connector (6-pin Mini-Din KB)
This connection is for a standard keyboard using a PS/2 plug. You may use a Din to Mini-Din adapter on standard
AT keyboards.
2.4.8 VGA Output Connector (15-pin female)
This connector is for output to a VGA-compatible device.
2.4.9 Serial Port (9-pin D-type COM1 & 10-pin COM2)
2.4.10 LAN Connector
The LAN Connector is used to attach RJ-45 cable. For 100Base-TX, your network cable must be
category 5, twisted-pair wiring with RJ-45 connectors. If you plan on running the adapter at 100Mbps, it
must be connected to a 100Base-TX hub. For 10Base-T, use category 3, 4 or 5 twisted-pair wiring.
2.4.11 Printer Port (25-pin D-type PRINTER)
You can enable the parallel port and choose the IRQ through the "Onboard Parallel Port" setting in
Integrated Peripherals of the CMOS SETUP UTILITY.
2.4.12 USB Connectors (4-pin USB & 5-pin JP12, JP13)
S630MA provides five USB ports. You can attach USB devices to the USB connector.
2.4.13 Game/MIDI/Line Out/Line In/Microphone In Connector (optional)
The connector is same as audio port of the back I/O panel. The cable is optional.
Page 12
2.4.14 Line Out Connector
The Line Out phonejack provides the audio outputs for the left and right stereo channels.
2.4.15 Line In Connector
The Line In phonejack is used to attach monaural or stereo devices such as a cassette, Digital Audio Tape, or
Minidisc players for playback, mixing, or recording.
2.4.16 Microphone In Connector
The Microphone In phonejack is used to attach a monaural microphone for live audio input for playback, mixing, or
recording.
2.4.17 Game/MIDI Port
The Game/MIDI Port connector is used to attach a joystick for game interaction or to attach an external MIDI
device for playback, mixing, or recording.
2.4.18 ATAPI IDE/Sony CD-ROM Audio (4-pin SONY)
The ATAPI IDE/Sony CD-ROM Audio connector is used to connect the audio cable from either an ATAPI IDE or
Sony CD-ROM drive for playback, mixing, and recording.
2.4.19 Panel Connection (24-pin JFRNT)
WARNING: To avoid the system from failing, turn off the power before connecting any
devices to the system.
Chapter 3. BIOS Setup
3.1 CMOS Setup Utility
To activate CMOS Setup, press <DEL> key immediately after you turn on the system. The following message "Press
DEL to enter SETUP" should appear in the lower left hand corner of your screen.
When you enter the CMOS Setup Utility, the Main Menu will be displayed (Figure 3-1). You can use arrow keys to
select your function, press <Enter> key to accept the selection and enter the sub-menu.
Figure 3-1. CMOS Setup Utility Main Screen
CMOS Setup Utility - Copyright ( C ) 1984 - 2000 Award Software
Page 13
>Standard CMOS Features >Frequency Control
>Advanced BIOS Features Load Fail-Safe Defaults
>Advanced Chipset Features
>Integrated Peripherals
Load Optimized Defaults
Set Password
>Power Management Setup Save & Exit Setup
>PnP / PCI Configurations Exit Without Saving
>PC Health Status
Esc : Quit ¯ ® ¬ : Select Item
F10 : Save & Exit Setup
Time, Date, Hard Disk Type...
Sub-Menu
Note that a right pointer symbol appears to the left of certain fields. This pointer indicates that a sub-menu can be
launched from this field. A sub-menu contains additional options for a field parameter. To call up a sub-menu, simple
move the highlight to the field and press <Enter>. The sub-menu will then immediately appear. Use the legend keys to
enter values and move from field within a sub-menu just as you would within a menu. Use the <Esc> key to return to
the main menu.
3.2 Standard CMOS Features
With the sub-menu (Figure 3-2), you can setup the; system date, system time, hard and floppy drive type, and display
adapter type. Please refer to your equipment specification when changing the setup. Use arrow keys to highlight items,
and use <PageUp>, <PageDown>, <+>, or <-> keys to scroll through the available options.
Figure 3-2. Standard CMOS Features Screen
CMOS Setup Utility - Copyright ( C ) 1984 - 2000 Award Software
Standard CMOS Features
Date ( mm : dd : yy ) Fri, Jan 1 1999 Item Help
Time ( hh : mm: ss ) 1 : 28 : 42
Menu Level >
>IDE Primary Master ST38641A
>IDE Primary Slave None Change the day, month,
>IDE Secondary Master None Year and century
>IDE Secondary Slave E-IDE CD-ROM Max 54X
Drive A 1.44M, 3.5 in.
Drive B None
Floppy 3 Mode Support Disabled
Video EGA/VGA
Halt On All Errors
Base Memory 640K
Extended Memory 14336K
Total Memory 15360K
¯ ® ¬: Move Enter : Select +/-/PU/PD : Value F10 : Save ESC : Exit F1 : General Help
F5 : Previous Value F6 : Fail-Safe Defaults F7 : Optimized Defaults
3.2.1 Date
To assign the system date, the format is "mm.dd.yy". The input range for the Month is 1-12. Range for Date
is 1-31. Range for Year is 1994-2079. System BIOS will calculate the day of the week automatically.
3.2.2 Time
Page 14
To assign the system time, the format is "hh:mm:ss". The setting is in military time. When entering 2:34pm
enter "14:34:00".
3.2.3 Hard Disks Setting
The BIOS supports Dual-Channel PIO and PCI Bus Master IDE ports. Each port supports one master and
one slave hard drive. You can use <Enter>＞ or <PageUp> or <PageDown> key to change hard drive
type. Incorrect setting may result in boot up error or system hang.
If your hard disk drive is not listed, you can select "Manual" mode to define your own drive manually. We
recommend that you select Type "AUTO" for all drives. The BIOS will auto-detect the hard disk drive and
CD-ROM drive at the POST stage.
If your hard disk drive is a SCSI device, please select "None" for your hard drive setting.
CMOS Setup Utility - Copyright ( C ) 1984 - 2000 Award Software
IDE Primary Master
IDE HDD Auto-Detection Press Enter Item Help
Menu Level >>
IDE Primary Master Auto
Access Mode Auto To auto-detect the
HDD's size, head… on
Capacity 8606 MB This channel
Cylinder 16676
Head 16
Precomp 0
Landing Zone 16675
Sector 63
¯ ® ¬: Move Enter : Select +/-/PU/PD : Value F10 : Save ESC : Exit F1 : General Help
F5 : Previous Value F6 : Fail-Safe Defaults F7 : Optimized Defaults
3.2.4 Floppy Drives A&B Setting
Select your floppy disk drive type. Options are 360KB (5.25"), 720KB (3.5"), 1.2MB (5.25"), 1.44MB
(3.5"), 2.88MB (3.5").
3.2.5 Floppy 3 Mode Support
This is required to support older Japanese floppy drives. Floppy 3 Mode support will allow reading and
writing of 1.2MB (as opposed to 1.44MB) on a 3.5-inch diskette.
3.2.6 Video Display Adapter Setting
Select the display adapter type for your system. Options are EGA/VGA, MONO, CGA40 and CGA80.
3.2.7 Halt On
This function allows the system to halt when an error is detected during Power-On Self-Test.
3.3 Advanced BIOS Features Setup
The sub-menu (Figure 3-3) includes all AWARD enhanced functions. The correct setting can enhance boot up
efficiency. You can assign system speed, setup sequence, typematic and system password setting. You can enter <F1>
key for help on highlighted topics. If you want to restore values before the changes you just made, press <F5> key. If
you want to restore default value, press <F6> or <F7> key.
Page 15
Figure 3-3. Advanced BIOS Features Screen
CMOS Setup Utility - Copyright ( C ) 1984 - 2000 Award Software
Advanced BIOS Features
Virus Warning Disabled Item Help
CPU Internal Cache
External Cache
CPU L2 Cache ECC Checking
Processor Number Feature
Enabled
Enabled
Enabled
Disabled
Menu Level >
Quick Power On Self Test Enabled
First Boot Device IDE-0
Second Boot Device Floppy
Third Boot Device SCSI
Fourth Boot Device Disabled
Swap Floppy Drive Disabled
Boot Up Floppy Seek Disabled
Boot Up NumLock Status On
Gate A20 Option Fast
Typematic Rate Setting Disabled
X Typematic Rate (Chars/Sec) 6
X Typematic Delay (Msec) 250
Security Option
OS Select For DRAM > 64MB
Setup
Non-OS2
HDD S.M.A.R.T. Capability
Report No FDD For WIN 95
Video BIOS Shadow
Disabled
Yes
Enabled
¯ ® ¬: Move Enter : Select +/-/PU/PD : Value F10 : Save ESC : Exit F1 : General Help
F5 : Previous Value F6 : Fail-Safe Defaults F7 : Optimized Defaults
( Scroll down to see more items , as shown here )
3.3.1 Virus Warning
When enabled, the BIOS will monitor the boot sector and the partition table on the hard drive for any
attempt to modify. If an attempt is detected, the BIOS will halt the system and prompt the warning message.
Select "Disabled" if you are installing a new operating system.
3.3.2 CPU Internal/External Cache
These options are to enable or disable CPU Internal (L1) Cache, or External (L2) Cache.
3.3.3 CPU L2 Cache ECC Checking
Select "Enabled" to enable CPU L2 Cache ECC Checking.
Select "Disabled" to disable CPU L2 Cache ECC Checking.
3.3.4 Processor Number Feature
This field will appear only when you are using a Pentium III processor. Each Pentium III processor comes
with an individual "processor serial number" which by default is activated. Therefore, when connected to
the internet, Pentium III processor transmits the serial number online making it possible to track your online
activity. The field provides you the option of disabling this function.
3.3.5 Quick Power On Self Test
Select "Enabled" to speed up time required to complete Power-On Self-Test.
3.3.6 First/Second/Third Boot Device & Boot Other Device
This option allows user to assign boot sequence of the system. Available options are Floppy, HDD, CDROM, SCSI, LAN and LS120/ZIP. Set " Boot Other Device" to Enabled if you wish to boot from another
Page 16
device.
3.3.7 Swap Floppy Drive
When enabled, physical drive A will be assigned to logical drive B, and physical drive B will be assigned to
logical drive A.
3.3.8 Boot Up Floppy Seek
The system will detect and verify operation of the floppy drive type.
3.3.9 Boot Up Numlock Status
The option allows the <NumLock> key to be activated after system boot up.
3.3.10 Gate A20 Option
This entry allows you to select how the gate A20 is handled. The gate A20 is a device used to address
memory above 1 Mbytes. Initially, the gate A20 was handled via a pin on the keyboard (Normal). Today,
while keyboards still provide this support, it is more common, and much faster, for the system chipset (Fast;
default) to provide support for gate A20.
3.3.11 Typematic Rate Setting
Select "Enabled" to configure "Typematic Rate" and "Typematic Delay" functions.
3.3.12 Typematic Rate
Use this option to set the rate at which a character keeps repeating while you hold down a key.
3.3.13 Typematic Delay
Select "Enabled" to set the length of delay before key strokes to repeat. Available options are "250", "500",
"750", and "1000".
3.3.14 Security Option
You can select whether the password is required every time the system boots or only when you enter the
Setup. You can assign "Set Password" in the main CMOS Setup Utility Screen.
3.3.15 OS Select for DRAM > 64MB
If you are using OS/2 operating system and installed memory is larger than 64MB. You need to have the
setting in the enable mode.
3.3.16 HDD S.M.A.R.T. Capability
The item allows you to set HDD S.M.A.R.T. Capability function. Configuration options: Enabled and
Disabled.
3.3.17 Report No FDD For WIN 95
While the FDD in " STANDARD CMOS SETUP " is set to NONE, set this option to No to release IRQ6 for
passing Win95 logo. This option is irrelevant under normal operation.
Page 17
3.3.18 Video BIOS Shadow
Video shadow copies BIOS code from slower ROM to faster RAM. BIOS can then execute from RAM.
3.4 Advanced Chipset Features Setup
These settings are intended for the Advanced Chipset function on the motherboard. Fine tuning these options, enhances
the performance of the system.
Figure 3.4 Advanced Chipset Features Screen
CMOS Setup Utility - Copyright ( C ) 1984 - 2000 Award Software
Advanced Chipset Features
> Advanced DRAM Control 1 Press Enter Item Help
> Advanced DRAM Control 2 Press Enter Menu Level >
System BIOS Cacheable Enabled
Video RAM Cacheable Enabled
Memory Hole At 15M-16M Disabled
AGP Aperture Size 64MB
Graphic Window WR Combin
Concurrent function (MEM)
Enabled
Enabled
Concurrent function (PCI) Enabled
PCI Delay Transaction
Memory Parity Check
Enabled
Disabled
¯ ® ¬: Move Enter : Select +/-/PU/PD : Value F10 : Save ESC : Exit F1 : General Help
F5 : Previous Value F6 : Fail-Safe Defaults F7 : Optimized Defaults
3.4.1 Advanced DRAM Control 1
CMOS Setup Utility - Copyright ( C ) 1984 - 2000 Award Software
Advanced DRAM Control 1
Auto Configuration Auto Item Help
SDRAM RAS Active Time 6T Menu Level >
SDRAM RAS Precharg Time 3T
RAS to CAS Delay 3T
Dram Background Command Delay 1T
LD-off Dram RD/WR Cycles Delay 1T
Write Recovery Time 1T
VCM REF To ACT/REF Delay 9T
VCM ACCT - ACT/REF Delay 8T
Early CKE Delay 1T Cntrl Normal
Early CKE Delay Adjust 1ns
¯ ® ¬: Move Enter : Select +/-/PU/PD : Value F10 : Save ESC : Exit F1 : General Help
F5 : Previous Value F6 : Fail-Safe Defaults F7 : Optimized Defaults
3.4.2 Auto Configuration
Auto Configuration installs preset default values for some of the timing parameters for RAM memory. We
recommend that you leave these items at the default value Auto.
3.4.3 SDRAM RAS Precharge Time
Page 18
The RAS Recharge means the timing to inactive RAS and the timing for DRAM to do Recharge before next
RAS can be issued.
3.4.4 RAS to CAS Delay
These are timing of SDRAM CAS Latency and RAS to CAS Delay, calculated by clocks. They are
important parameters affects SDRAM performance.
3.4.5 The other items in Advanced DRAM Control 1
These items set the timing and wait states for SDRAM memory. We recommend that you leave these items
at the default value.
3.4.6 Advanced DRAM Control 2
CMOS Setup Utility - Copyright ( C ) 1984 - 2000 Award Software
Advanced DRAM Control 2
Mem Command Output Time Delay 1T Item Help
SDRAM/VCM CAS Latency SPD Menu Level >
SDRCLK Control +2.0 ns
SDWCLK Control CS#/CKE +2.0 ns
SDWCLK Control MA/SRAS +2.0 ns
SDWCLK Control DQM/MD -0.5 ns
EGMRCLK Control +3.0 ns
EGMWCLK Control +3.0 ns
AGTL Pull Up Control Enabled
AGTL Feed Back Control Enabled
¯ ® ¬: Move Enter : Select +/-/PU/PD : Value F10 : Save ESC : Exit F1 : General Help
F5 : Previous Value F6 : Fail-Safe Defaults F7 : Optimized Defaults
3.4.7 SDRAM/VCM CAS Latency
This controls the latency between the SDRAM read command and the time that the data actually becomes
available.
3.4.8 The other items in Advanced DRAM Control 2
These items set timing parameters for the CPU access. We recommend that you leave these items at the
default value.
3.4.9 System BIOS Cacheable
Allows the system BIOS to be cached for faster system performance.
3.4.10 Video RAM Cacheable
This item lets you cache Video RAM A000 and B000.
3.4.11 Memory Hole At 15M-16M
Enabling this feature reserves 15MB to 16MB memory address space to ISA expansion cards that
specifically require this setting. This makes the memory from 15MB and up unavailable to the system.
Expansion cards can only access memory up to 16MB.
3.4.12 AGP Aperture Size (MB)
Page 19
Choose 4, 8, 16, 32, 64, 128, 256MB. Memory-mapped, graphics data structures can reside in the Graphics
Aperture.
3.4.13 Graphic Window WR Combin
Use this item to enable or disable data combination from buffer then write to memory feature.
3.4.14 Concurrent function (MEM) & (PCI)
Use these items to enable or disable concurrent memory/PCI and CPU action.
3.4.15 PCI Delayed Transaction
If the chipset has an embedded 32-bit write buffer to support delay transaction cycles, you can enable this
item to provide compliance with PCI Ver. 2.1 specifications. We recommend that you leave this item at the
default value.
3.4.16 Memory Parity Check
This item enables a parity check during boot-up memory testing. Only set this item to enabled if you are
using DRAM memory with parity.
3.5 Integrated Peripherals
You can control Input and Output functions from this screen.
Figure 3-5 Integrated Peripherals
CMOS Setup Utility - Copyright ( C ) 1984 - 2000 Award Software
Integrated Peripherals
> SIS 630 OnChip IDE Device Press Enter Item Help
> SIS 630 OnChip PCI Device Press Enter Menu Level >
> SIS 950 SuperIO Device Press Enter
USB Controller Enabled
USB Keyboard Support Disabled
IDE HDD Block Mode Enabled
Init Display First PCI Slot
System Share Memory Size 8 MB
¯ ® ¬: Move Enter : Select +/-/PU/PD : Value F10 : Save ESC : Exit F1 : General Help
F5 : Previous Value F6 : Fail-Safe Defaults F7 : Optimized Defaults
3.5.1 SIS 630 OnChip IDE Device
CMOS Setup Utility - Copyright ( C ) 1984 - 2000 Award Software
SIS 630 OnChip IDE Device
Internal PCI/IDE Both Item Help
IDE Primary Master PIO Auto Menu Level >
IDE Primary Slave PIO Auto
IDE Secondary Master PIO Auto
IDE Secondary Slave PIO Auto
IDE Primary Master UDMA Auto
IDE Primary Slave UDMA Auto
IDE Secondary Master UDMA Auto
IDE Secondary Slave UDMA Auto
IDE Burst Mode Enabled
Page 20
¯ ® ¬: Move Enter : Select +/-/PU/PD : Value F10 : Save ESC : Exit F1 : General Help
F5 : Previous Value F6 : Fail-Safe Defaults F7 : Optimized Defaults
3.5.2 Internal PCI/IDE
Use this item to enable or disable the PCI IDE channels that are integrated on this motherboard.
3.5.3 IDE Primary & Secondary Master/Slave PIO
These four PIO fields let you set a PIO mode (0-4) for each of four IDE devices. When under "Auto" mode,
the system automatically set the best mode for each device
3.5.4 IDE Primary & Secondary Master/Slave UDMA
When set to "Auto" mode, the system will detect if the hard drive supports Ultra DMA mode.
3.5.5 IDE Burst Mode
Use this item to enable a buffer for bus master PCI IDE transfers.
3.5.6 SIS 630 OnChip PCI Device
CMOS Setup Utility - Copyright ( C ) 1984 - 2000 Award Software
SIS 630 OnChip PCI Device
SIS-7018 AC97 AUDIO Enabled Item Help
SIS-7013 S/W Modem Disabled Menu Level >
SIS-900 10/100M ETHERNET Enabled
SIS-900 MAC Address Input Press Enter
¯ ® ¬: Move Enter : Select +/-/PU/PD : Value F10 : Save ESC : Exit F1 : General Help
F5 : Previous Value F6 : Fail-Safe Defaults F7 : Optimized Defaults
3.5.7 SIS-7018 AC97 AUDIO
This item enables the integrated audio capabilities.
3.5.8 SIS-7013 S/W Modem
This item enables the integrated software modem capabilities.
3.5.9 SIS-900 10/100M ETHERNET
This item enables the integrated Ethernet capabilities.
3.5.10 SIS-900 MAC Address Input
The address was set OK by manufacturer. If the data is lost, system will prompt you to key in the address
number. Please follow the address number sticker that on motherboard to key in the number.
3.5.11 SIS 950 SuperIO Device
CMOS Setup Utility - Copyright ( C ) 1984 - 2000 Award Software
SIS 950 SuperIO Device
Page 21
Onboard FDC Controller Enabled Item Help
Onboard Serial Port 1 3F8 / IRQ4 Menu Level >
Onboard Serial Port 2 2F8 / IRQ3
UART Mode Select Normal
X UR2 Duplex Mode Half
Onboard Parallel Port 378 / IR7
Parallel Port Mode
X ECP Mode Use DMA
SPP
3
Game Port Address 201
Midi Port Address
Midi Port IRQ
330
10
¯ ® ¬: Move Enter : Select +/-/PU/PD : Value F10 : Save ESC : Exit F1 : General Help
F5 : Previous Value F6 : Fail-Safe Defaults F7 : Optimized Defaults
3.5.12 Onboard FDC Controller
Select "Enabled" to activate the on-board FDC
Select "Disabled" to activate an add-on FDC
3.5.13 Onboard Serial Port 1 & 2
Select an address and corresponding interrupt for the first/second serial port. The default value for the first
serial port is "3F8/IRQ4" and the second serial port is "2F8/IRQ3".
3.5.14 UART Mode Select & UR2 Duplex Mode
This item defines the operation of serial port 2. In the Normal setting, serial port 2 is assigned to the
external COM2 connector. If you have installed an optional infrared port, you must change the setting of
this item to one of the Infrared settings (usually IrDA). These settings will disable the external COM2 serial
port connector and assign the resources to the infrared device. If you have selected an IR mode, use the
following item UR2 Duplex Mode to define if the IR port is full duplex or half duplex.
3.5.15 Onboard Parallel Port
Select address and interrupt for the Parallel port.
3.5.16 Parallel Port Mode
Select an operating mode for the parallel port. Mode options are SPP, EPP, ECP and ECP+EPP.
3.5.17 ECP Mode Use DMA
Select a DMA channel if parallel port is set as ECP or ECP+EPP.
3.5.18 Game Port Address
This field sets the address of the onboard game port connector.
3.5.19 Midi Port Address
This field is used to select the midi port's address. If you have selected the midi port's address, you may
select its IRQ in the " Midi Port IRQ ".
3.5.20 Midi Port IRQ
Page 22
This field is used to select the midi port's IRQ.
3.5.21 USB Controller
Select Enabled if your system contains a Universal Serial Bus (USB) controller.
3.5.22 USB Keyboard Support
This item lets you enable or disable the USB keyboard driver within the onboard BIOS.
3.5.23 IDE HDD Block Mode
This feature enhances disk performance by allowing multi-sector data transfers and eliminates the interrupt
handling time for each sector.
3.5.24 Init Display First
Select "AGP" or "PCI Slot" for system to detect first when boot-up.
3.5.25 System Share Memory Size
This item defines the amount of system memory that will be shared and uses as video memory.
3.6 Power Management Setup
Power management decreases power usage under the pre-defined standby time range.
Figure 3-6. Power Management Setup Screen
CMOS Setup Utility - Copyright ( C ) 1984 - 2000 Award Software
Power Management Setup
ACPI function Enabled Item Help
ACPI Suspend Type S1 (POS)
Menu Level >
Video Off Option Susp, Stby -> off
Video Off Method V/H SYNC+Blank
Switch Function Break/Wake
MODEM Use IRQ 3
Power Button Override Instant Off
> PM Wake Up Events
Press Enter
¯ ® ¬: Move Enter : Select +/-/PU/PD : Value F10 : Save ESC : Exit F1 : General Help
F5 : Previous Value F6 : Fail-Safe Defaults F7 : Optimized Defaults
3.6.1 ACPI Function
This item allows you to enable or disable the function of Advanced Configuration and Power Interface which offers
improved power management .
3.6.2 ACPI Suspend Type
This field is used to select the type of Suspend function.
S1 (POS): Enables the Power On Suspend function.
Page 23
S3 (STR): Enables the STR function.
3.6.3 Video Off Option
When enabled, this feature allows the VGA adapter to operate in a power saving mode.
Always On Monitor will remain on during power saving modes.
Suspend --> Off Monitor blanked when the systems enters the
Suspend mode.
Susp,Stby --> Off Monitor blanked when the system enters either
Suspend or Standby modes.
All Modes --> Off Monitor blanked when the system enters any power
saving mode.
3.6.4 Video Off Method
This field defines the video off features. The following options are available: DPMS Supported, Blank
Screen, V/H SYNC+Blank. The DPMS (Display Power Management System) features allow the BIOS to
control the video display card if it supports the DPMS feature.
3.6.5 Switch Function
This item defines if pressing the power switch will cause the system to wake up from suspend or standby
mode.
3.6.6 MODEM Use IRQ
This item tells the Power Management BIOS which IRQ is assigned to the installed MODEM. Option are
NA, 3, 4, 5, 7, 9, 10 and 11.
3.6.7 Power Button Override
Under ACPI (advanced configuration and power interface ) the system can be turned off mechanically ( by
the power button ) or it can undergo a software power off. If the system has been turned off by software, the
system can be resumed by a Alarm wake up signal. This item allows you to define a software power off
using the power button. If the value is set to Instant-Off, the power button will automatically cause a
software power off. If the value is set to Delay 4 Sec. The power button must be held down for a full four
seconds to cause a software power off.
3.6.8 PM Wake Up Events
CMOS Setup Utility - Copyright ( C ) 1984 - 2000 Award Software
PM Wake Up Events
IRQ [3-7, 9-15], NMI Enabled Item Help
IRQ 8 Break Suspend Disabled Menu Level >
Ring Power Up Control Disabled
MACPME Power Up Control Disabled
PCIPME Power Up Control Disabled
Power Up by Alarm Disabled
x Month Alarm NA
x Date of Month Alarm 0
x Time ( hh:mm:ss ) Alarm 0 0 0
¯ ® ¬: Move Enter : Select +/-/PU/PD : Value F10 : Save ESC : Exit F1 : General Help
F5 : Previous Value F6 : Fail-Safe Defaults F7 : Optimized Defaults
Page 24
3.6.11 IRQ [3-7,9-15], NMI
When this item is enabled, any activity through the system interrupt request lines 3-7, 9-15 and the nonmasked interrupt can reset power-saving mode timeouts to zero, or resume the system from a power-saving
mode.
3.6.12 IRQ 8 Break Suspend
When this item is enabled, any activity through the system interrupt request lines 8 can reset power-saving
mode timeouts to zero, or resume the system from a power-saving mode. IRQ 8 is normally used by the
system real time clock.
3.6.13 Ring Power Up Control
The option lets you specify enable or disable external Modem Wake Up function. The function of power on
through modem when system is off.
Please set the item to "Enabled" then let the system to enter the environment of DOS or Windows 95/98 OS
before system is power off. As long as there are any message through the Modem to enter the System during
system is power off. The system will enable power on function.
3.6.14 MACPME Power Up Control
This allows you to remotely power up your system through your network by sending a wake-up frame or
signal. With this feature, you can remotely upload/download data to/from systems during off-peak hours.
Set to Enabled to set this feature and make sure your system has an ATX power supply with at least 720mA
+5V standby power.
3.6.15 PCIPME Power Up Control
If this item is set as Enabled, PCI peripherals drive PME (Power Management Event) signal to wake the system
from low-power states S1-S5.
3.6.16 Power Up by Alarm
Set this option to enable or disable the RTC Alarm to Wake Up the system which is set at soft Off.
3.6.17 Month Alarm, Date (of Month) Alarm, Time (hh:mm:ss) Alarm
Set these options to specify the RTC Alarm time on Month/Date / Hour / Minute / Second.
3.7 PNP/PCI Configurations Setup
Figure 3.7 PNP/PCI CONFIGURATIONS SETUP
CMOS Setup Utility - Copyright ( C ) 1984 - 2000 Award Software
PnP / PCI Configurations
Reset Configuration Data Disabled Item Help
Menu Level >
Resources Controlled By Auto (ESCD)
x IRQ Resources Press Enter
PCI/VGA Palette Snoop Disabled
¯ ® ¬: Move Enter : Select +/-/PU/PD : Value F10 : Save ESC : Exit F1 : General Help
F5 : Previous Value F6 : Fail-Safe Defaults F7 : Optimized Defaults
3.7.1 Reset Configuration Data
Page 25
In case a conflict occurs after you assign the IRQs or after you configure your system, you can enable this function
to allow your system to automatically reset your configuration and reassign the IRQs, DMAs, and I/O address.
3.7.2 Resources Controlled By
Default setting is "Auto (ESCD)". This setting allows the BIOS to self detect setting and Plug-and-Play devices
during start up. The user can select and configure IRQs under "Manual" mode.
3.7.3 IRQ Resources
CMOS Setup Utility - Copyright ( C ) 1984 - 2000 Award Software
IRQ Resources
IRQ-3 assigned to PCI Device Item Help
IRQ-4 assigned to PCI Device Menu Level >
IRQ-5 assigned to PCI Device
IRQ-7 assigned to PCI Device Legacy ISA for devices
IRQ-9 assigned to PCI Device compliant with the
IRQ-10 assigned to PCI Device original PC AT bus
IRQ-11 assigned to PCI Device Specification, PCI/ISA
IRQ-12 assigned to PCI Device PnP for devices
IRQ-14 assigned to PCI Device Compliant with the
IRQ-15 assigned to PCI Device Plug and Play standard
architecture
¯ ® ¬: Move Enter : Select +/-/PU/PD : Value F10 : Save ESC : Exit F1 : General Help
F5 : Previous Value F6 : Fail-Safe Defaults F7 : Optimized Defaults
3.7.4 IRQ-xx assigned to
If your ISA card is not PnP compatible and requires a special IRQ to support its function, set the selected IRQ-x
assigned to:" Reserved". This setting informs the PnP BIOS to reserve the selected IRQ for the installed ISA card.
3.7.5 PCI/VGA Palette Snoop
Enable this option to correct screen color shifts, when there is a combination of VGA cards, accelerator cards, or
MPEG cards present.
3.8 PC Health Status
Figure 3.8 PC Health Status
CMOS Setup Utility - Copyright ( C ) 1984 - 2000 Award Software
PC Health Status
Vcore 1.60V Item Help
Vcc25 2.51V Menu Level >
Vcc3 3.28V
Vcc 5.02V
+12V 12.16V
5VSB 4.99V
Voltage Battery 3.28V
CPU Temperature 41°C
System Temperature 36°C
CPUFAN Speed 4017 RPM
ChassisFAN Speed 0 RPM
¯ ® ¬: Move Enter : Select +/-/PU/PD : Value F10 : Save ESC : Exit F1 : General Help
F5 : Previous Value F6 : Fail-Safe Defaults F7 : Optimized Defaults
3.8.1 Vcore, Vcc25, Vcc3, Vcc, +12V, 5VSB & Voltage Battery (xx.xxV)
Page 26
The onboard hardware monitor is able to detect the voltage output by the voltage regulators. These values
refresh upon any key entry. The function is optional.
3.8.2 Current CPU & System Temperature (xx°C)
The onboard hardware monitor is able to detect the temperatures of motherboard and CPU. These values
refresh upon any key entry. The function is optional.
3.8.3 CPUFAN & ChassisFAN Speed (xxxxRPM)
The onboard hardware monitor is able to detect chassis fan speed, CPU fan speed in Rotations Per Minute
(RPM). These values refresh upon any key entry in the BIOS setup screen.
3.9 Frequency Control
Figure 3.9 Frequency Control
CMOS Setup Utility - Copyright ( C ) 1984 - 2000 Award Software
Frequency Control
Auto Detect DIMM/PCI Clk Enabled Item Help
CPU Clock Ratio Jumpless By H/W Menu Level >
¯ ® ¬: Move Enter : Select +/-/PU/PD : Value F10 : Save ESC : Exit F1 : General Help
F5 : Previous Value F6 : Fail-Safe Defaults F7 : Optimized Defaults
3.9.1 Auto Detect DIMM/PCI CLK
If you have the EMI issue, set the option as Enabled, it keeps its interference under control.
3.9.2 CPU Clock Ratio Jumpless
Use CPU Clock Ratio to set a multiple. The multiple times the system bus must equal the core speed of the
installed processor e.g. 3.5 (multiple) x 100 MHz (system bus) = 350 MHz (installed processor clock
speed). We recommend that you leave the item to there default value By H/W (Hardware defined).
3.10 Load Fail-Safe Defaults
This loads the troubleshooting default values permanently stored in the ROM chips. These settings are not optimal and
turn off all high performance features. You should use these values only if you have hardware problems. Highlight this
option in the main menu and press <Enter>. The message below will appear.
Load Fail-Safe Defaults (Y/N)?N
If you want to process, type <Y> and press <Enter>. The default settings will be loaded.
3.11 Load Optimized Defaults
This feature loads optimized setting from the BIOS ROM. Use the default values as standard values for your system.
Highlight this option in the main menu and press <Enter>. The message below will appear.
Load Optimized Defaults (Y/N)?N
Type <Y> and press <Enter> to load the Setup default values.
Page 27
3.12 Set Password
You can assign, modify, or cancel password settings. To modify, highlight "Set Password" and press the <Enter> key.
The screen will prompt you ("Enter Password:"). Enter your password. The maximum size of the password is 8
characters. System will prompt you to reenter the password to verify. Remember the passwords are case sensitive.
If you want to remove the passwords, either delete passwords or press <Enter> when prompting for new password.
If you want it to require password upon initial system startup and upon entering the CMOS Setup Utility, you will need
to change the selection of the (Security Option) under (Advanced BIOS Features ) to "System".
If the setting is "Setup", the system will only require the password you activate CMOS Setup Utility.
3.13 Save & Exit Setup
When all the changes have been made, highlight "Save & Exit Setup" and press <Enter>. The message below will
appear:
Save to CMOS and Exit (Y/N)? N
Type "Y" and press <Enter>. The modifications you have made will be written into the CMOS memory, and the system
will reboot.
3.14 Exit Without Saving
When you do not want to save the changes you have made, highlight "Exit Without Saving" and press <Enter>, The
message below will appear:
Quit Without Saving (Y/N)? N
Type "Y" and press <Enter>. The system will reboot.
Chapter 4. Software installation
4.1 Installing the Sound Driver
4.1.1 Windows 95/98
1. Start up Windows 95 or Windows 98.
[ If your Windows 95 is older version, please install the USB supplement service pack ( usbsupp.exe ) files first.
You can get this file from http://www.microsoft.com ]
2. Insert the CD Driver into the CD drive-enter the \S630MA\SOUND directory on the CD-ROM and double-click
SETUP.EXE
3. Follow the prompts to complete the installation.
4. You must restart your computer for the installation to complete.
5. If Insert Disk dialog is displayed, please insert the Windows 95 or 98 CD-ROM into the CD drive, then click "
OK " button.
6. You must restart your computer again to take the new setting effect.
4.1.2 Windows 2000/NT 4.0 Installation
1. Insert the CD Driver into the CD drive-enter the \S630MA\SOUND directory on the CD-ROM and double-click
SETUP.EXE
2. Follow the prompts to complete the installation.
3. You must restart your computer for the installation to complete.
Page 28
4.2 Installing the LAN Driver
4.2.1 Windows 95/98/2000
1. Insert the CD Driver into the CD drive-enter the \S630MA\LAN directory on the CD-ROM and double-click
SETUP.EXE
2. Follow the prompts to complete the installation.
3. If Insert Disk dialog is displayed, please insert the Windows 95 or 98 or 2000 CD-ROM into the CD drive, then
click " OK " button.
4. You must restart your computer for the installation to complete.
4.2.2 Windows NT 4.0
1. Install Windows NT 4.0
2. When Windows NT Workstation Setup dialog box is appeared, select "Wired to the network" then press "Next"
button.
3. Click "Select from list..." button then select "Have Disk...".
4. Insert CD Driver Disk to CD-ROM drive and specify the correct path, e.g. D:\S630MA\LAN\NT40, then click
"OK" button.
5. Select one of the following models: "SiS 0900 PCI Fast Ethernet Adapter" then click "OK".
6. The SIS 900 PCI Fast Ethernet Adapter will be shown on the Network Adapters list. Click "Next" button. (After
the LAN driver was loaded, please re-insert NT 4.0 CD to CD- ROM)
7. In the dialog box that appears, select the Media Type and enter the Network address for the adapter if necessary
(You can click Help for more detailed information about these settings). Click "OK" to complete this dialog box (or
Cancel to terminate the configuration without completing it).
8. Exit the Network control panel window. Windows NT asks if you wish to reboot. You must reboot before the
adapter will function properly.
4.2.3 The other Operation Systems
Please refer to the README.TXT file in each directory.
4.3 Installing the Graphics Driver
4.3.1 For Windows 95/98
1. Insert the CD Driver into CD drive - enter the \S630MA\VGA\WIN9X directory on the CD Driver and doubleclick SETUP.EXE.
2. Follow the prompts to complete the installation.
3.You must restart your computer for the installation to complete.
4.3.2 For Windows 2000
1. Insert the CD Driver into CD drive - enter the \S630MA\VGA\WIN2000 directory on the CD Driver and
double-click SETUP.EXE to install VGA driver.
2. Follow the prompts to complete the installation.
3.You must restart your computer for the installation to complete.
4.Run "SETUP.EXE" in the directory of \S630MA\VGA\Win2000\AGP to install AGP driver.
5.You must restart your computer for the installation to complete.
4.3.3 For Windows NT 4.0
1. Start Windows NT4.0 with Service Pack 4.0 or later version.
2. Click "Start" menu and select Control Panel from Settings group.
3. Select "Display" icon.
4. Select "Settings" of Display Properties.
5. Select "Display Type…".
6. Select "Change…" from the Adapter Type area.
Page 29
7. Select "Have Disk…" of Change Display.
8. Place the CD Driver Disk into CD-ROM Drive.
9. When the "Install from Disk" dialog box appears, type the directory storing the drivers and click "OK". The
directory in CD-Title is at "D:\S630MA\VGA\WINNT40".
10. When the "Change Display" dialog box appears, click "OK".
11.When the "Third-party Drivers" dialog box appears, click "Yes".
12.A message will appear stating that the drivers were successfully installed. Click "OK". You must now restart
Windows NT 4.0.
Loading...