COMMELL MP-840 User Manual

Page 1
MP-840
User’s Manual
Edition 1.0
Page 2
MP-840
Copyright
Copyright 2009 all rights reserved. This document is copyrighted and all rights are reserved. The information in this document is subject to change without prior notice to make improvements to the products. This document contains proprietary information and protect ed by copyright. No part of this document may be reproduced, copied, or translated in any form or any means without prior written permission of the manufacturer. All trademarks and/or registered trademarks contains in this document are property of their respective owners.
Disclaimer
The company shall not be liable for any incidental or consequential damages resulting from the performance or use of this product. The company does not issue a warranty of any kind, express or implied, including without limitation implied warranties of merchantability or fitness for a particular purpose. The company has the right to revise the manual or include changes in the specifications of the product described within it at any time without notice and without obligation to notify any person of such revision or changes.
Trademark
All trademarks are the property of their respective holders.
Any questions please visit our website at TUhttp://www.commell.com.twUT.
1
Page 3
MP-840
Packing List:
Hardware :
MP-840 Mini-PCI Capture Card x1
Cable kit :
Video cable ( Included )
D-SUB 9 Cable x 1
4-Ch BNC video input Cable x 1
(OALDB9-H15) (OALBNCE4)
Audio cable ( Option )
Dual D-SUB 9 Cable x 1
4-Ch RCA audio input Cable x 1
(OAL2DB9-H15) (OALDB9-AUD4)
CD Content : Windows Drivers/SDK & User’s Manual
2
Page 4
MP-840
1.0 <Product Specification>
General Specification
Form Factor Compression Format
Cable kit
Features
OS Support Software
Mini-PCI Type-III B Video: H.264 Hardware compression technology Audio: G.721 compression 1 x DF14 to D-sub 9 Cable 1 x D-sub 9 to 4-ch BNC connector Cable 1 x DF14 to dual D-sub 9 Cable (option)-Audio 1 x D-sub 9 to 4-ch RCA connector Cable (option)-Audio Display Rate: NTSC: 1-ch total 30 fps / D1 resolution PAL: 1-ch total 25 fps / D1 resolution Recording Rate: NTSC: 4-ch total 120 fps / D1 resolution PAL: 4-ch total 100 fps / D1 resolution Windows XP , Vista ( 32-bit ) Windows SDK ( support directdraw display mode) , Network Streaming SDK
Dimensions (L x W)
59.75mm x 44.6mm
3
Page 5
MP-840
1.1 <Component Placement>
CN_AV
115
1.2 <Mechanical Drawing>
4
Page 6
MP-840
1.3 <Connector Reference>
Audio input
CN_AV
Video input
2
115
CN_ AV Type: 15-pin DF14/Male (Pitch=1.25mm)
CN_AV
Pin Description Pin Description
1 CAM_IN1 11 AUDIO2 2 GND_Vd 12 AUDGND 3 CAM_IN2 13 AUDIO3 4 GND_Vd 14 AUDGND 5 CAM_IN3 15 AUDIO4 6 GND_Vd 7 CAM_IN4 8 NC 9 AUDIO1 10 AUDGND
5
Page 7
MP-840
1.4 <Driver Setting>
1. Copy the CD Driver folder to disk, Ex: C:\ , D:\ …
2. Please choose Device Manager then you can see Other devices
6
Page 8
MP-840
3. Please choose Multimedia Controller then press advanced
7
Page 9
MP-840
4. Please select file location
C:\MP-840_090907\driver
8
Page 10
MP-840
5. Please press continue anyway
9
Page 11
MP-840
6. Press Finish
10
Page 12
MP-840
7. Driver install succeed
11
Page 13
MP-840
1.5 <Application files> location Æ C:\MP-840_090824\bin
AHWinApp.exe (Demo program) AHWinPlayer.exe (Search program) NetViewer.exe (Streaming program) ALWatermark.exe (For checking watermark) ALMonitor.exe (For check current compression rate) ALCommon.dll (puplic library) AZDevCtrl.dll (Driver interface library) MyAVCD.dll (S/W Decoder library) G721Codec.dll (Voice codec library) WatermarkDLL.dll (Watermark library)
1.6 <Demo program play>
1) The Program is composed by Application program and Player (AHWinPlayer.exe).
2) If the application program was activated, it will be come out below window in the screen (FYI, Default camera input is set by NTSC).
12
Page 14
MP-840
3) If the program is activated, 4ch display screen will be come out as a default.
4) The right part of display is composed of Display mode, Reset & Exit,
Display set block.
5) The below [1]~[4] button of Display is for channel choice.
6) The below number of channel choice button means frame per second
of each channel compressed and if the capture start, put a mark frame number which is captured.
7) The Show, Hide block in the right-below part could activate or disable
detailed setting dialogs.
1.6.1 <Display Mode>
1) The screen displayed is controlled by Display Mode.
2) If it choose [1 Display], it comes out 720x480 size for just one channel
in display screen and in this time, the channel could be changed by pressing [CH Down], [CH Up] button and also choose channel by pressing [1]~[4] button.
3) [1 Display] [4 Display], could choose the channel in the same way.
1.6.2 <Search>
1)This button to playback the record file
13
Page 15
MP-840
1.6.3 <Capture>
1) There are two [Start] and [Stop] buttons.
2) If choose [Start] button, the live and capture image is displayed.
3) If choose [Stop] button, the live and capture image stops.
1.6.4 <Reset & EXIT>
1) There are two [All Reset], [EXIT] buttons.
2) If [All Reset] button press, the value in PC Card is initialized in PC Card.
3) If [EXIT] button press, Application program is finished.
1.6.5 <Display>
1) It could choose [Live] or [H.264] in Display setting block.
2) If you choose [Live] in capturing status, the chosen channel’s live image is displayed in the screen in the real time.
3) If you choose [H.264] in capture start status, you could wat ch law capture image.
14
Page 16
MP-840
1.6.6 <Capture Information>
1) You could see camera off and motion event status in the right part of
program window.
2) On the occasion of not having camera input, it will be displayed the red color “V” letter.
3) On the occasion of working motion event, it will be displayed the red color “M” letter.
4) Total: Show the 1ch to 4 ch total FPS.
1.6.7<Menu expansion>
1) There are two [Show] and [Hide] buttons.
2) If you press [Show] button, Menu expansion which could set
application program in detail is displayed under main screen.
3) [Hide] is used for hiding this expansion-menu.
15
Page 17
MP-840
1.7 <Demo program menu expansion>
1.7.1 <General>
1) There are [General], [Camera], [Codec], [Register], [Color], [OSD], [Motion], [Audio], [Network] tap in expansion-menu.
2) You could NTSC and PAL in [General] tap.
3) Default is NTSC, if you want change from NTSC to PAL, choose [PAL-B] and press [All Reset] button.
4) You could choose Hard disk drive in [Save Drive]. Default is C Drive.
1.7.2 <Camera>
1) [Camera] : You can check the tab-settings through Rec in [Display] of main screen. User can use this image when the user does Network transmit.
2) Each channel could set the resolution.
3) All channel is set 720x480 (D1) resolution as a default. (NTSC).
16
Page 18
MP-840
1.7.3 <Codec>
1) It choose Encoding Path.
2) [GOP] : could control the number of group of I frame and P frame.
3) [Skip Count] : could control the number of frame per second of chosen
channel.
4) [Bit Rate] : set the display quality of chosen channel.
- set VBR, CBR or Hybird-VBR
- I-Frame QP : set the display quality value of I Frame.
- P-Frame QP : set the display quality value of P Frame.
- QP-Limit, BPS Limit : set display quality limited value when it set CPR.
5) [Watermark] : recognition of On/Off water mark of chosen channel and
choose the level.
6) [Frame Picture Type] :set field resolution of Odd, Even of D1 image.
On the occasion of Separated, it is displayed Even Field in upper side, Odd Field in below side.
7) [Key Frame Encoding] : set whether or not use of Key Frame of chosen
channel.
8) [Interpolation Encoding] : set function to be shorten color line when H.264
compress, the color information is changed from 4:2:2 to 4:2:0
17
Page 19
MP-840
1.7.3 < Pre-Filter >
1) Choose Encoding Path. (Possible to set per each path)
2) [Pre-Filter Enable]: Activate filter function of chosen Path.
3) [Crominance Enable] : It activate the noise reduction function in the
chrominance level.
4) [Apply Automatically] : If you check [Apply Automatically] clause, the filter
function is activated automatically when the noise-image put into
5) [Pre-Filter Type] : It sets kinds of filter.
- HV :
It has the lowest level of noise-reduction function. The improving effect of compression rate is very small and the picture quality is maintained as the original one.
- HS : It has lower level of noise-reduction function. The improving effect of
compression rate is is small and the picture quality is maintained as nearly as the original one.
- CX : It has middle level of noise-reduction function. The improving effect of
compression rate is better. The picture quality is little lower and the resolution in the border of the original one become dim.
- AS : It has high level of noise-reduction function. The improving effect of
compression rate is best. The picture quality is lower and the resolution in the border of the original one become dimmer.
18
Page 20
MP-840
1.7.4 < Register >
1) Register Tap could set PCI Base Memory of BAR2/BAR3, TW2864
2) You could access on the register of each function by using various taps PCI Base Memory BAR3.
3) [Get] button shows the selected IC Register on the Data space, [Set] button write the input value of Data space on the chip’s Address. (Caution) You have to 16 hex character in Address and Data space. Ex) 31(0), 3B(0), 0x3C (X)
1.7.5 < Color >
1) Each channel or all channel at the same time could set [Brightness],
[Contrast], [Color], [Hue].
2) Choose the channel in the left and set the value in the right.
3) If you want to set at the same time, check and set [All]
4) If you press Default on the right below side, all channel will be
initialization.
19
Page 21
MP-840
1.7.6 <OSD >
1) It could be revised the OSD to be seen by PC, TV Monitor.
2) Each camera has been set channel number as a default like channel 1.
3) If it click [Start] in the [Capture] after revising OSD and checking
[EncdeOSD], the revised letter is displayed in the Monitor screen.
4) If you don’t want see OSD, it has only to do disable [EncdeOSD] after
stopping [Capture].
1.7.7 <Motion>
1) It is set the [Motion Capture Enable], [Threshold], [Detect Block Count], [Rect] In Motion tap.
2) On the occasion of choosing only one channel in [Motion Channel], input setting value is applied in the just chosen channel.
3) On the occasion of checking [ALL] check box, it could set all channel value at one time.
4) It is controlled sensitivity of Motion Detect in slide bar of [Threshold] block.
5) It could control block-count to recognize motion by using slide-bar of
20
Page 22
MP-840
[Detect Block Count].
6) It could choose motion part in [Rect]. a) [All Area] – Designated all area into motion part. b) [Part Area] – Designated part of screen into motion part by using mouse. c) [Area Erase] – deleted all designated part.
1.7.8 <Audio>
1) [Audio] support 16ch and each channel is possible to enable or record.
2) Volume control is possible in each [Audio In], [Audio Out].
3) If it check all in [Audio Channel Select], all channel is chosen and could set at one time.
Note : SDK does not support audio playback function.
1.7.9 <Network>
Enable or Disable the Network Server.
21
Page 23
MP-840
1.8 <Play back program>
If you play AHWinplayer.exe, it will come out like upper. This is the program for play recorded video image.
The recorded file folder at C:\Alogics or D:\Alogics… Video file Æ xxxxxx.264 Audio file Æ xxxxxx.g721 Note:
SDK does not support audio playback function.
22
Page 24
MP-840
1.
3.
2.
4.
5.
6.
1) Calendar status : It displays recorded date and chosen date in right upper part. The chosen date is displayed by red color and the recorded date is displayed with shadow by dark color. It could choose the date by clicking mouse.
2) You can choose the partition mode on the right side of Display Mode tab.
3) Time status : It is displayed the re corded time by hours and min utes in the below part. The number of 0~24 means time and the chosen time is displayed by red color and the recorded time is displayed with shadow by dark color. It could choose the time by clicking the number.
4) Minute unit status : The chosen time is divided with 60 minutes a nd displayed i n the right below part. A default is displayed 60 minute in 4 channel. On the occasion of having the recorded part, it is display with shadow. If it clicks the point which you want to search, it is displayed by minute unit. Slide bar : It could control the time which you look for by moving the slide bar. The slide bar is fit into minute unit.
23
Page 25
MP-840
5) Play button : There are buttons related play in the below part of slide bar. From left, there are (R-I/Search : moving per I frame unit in reverse), (R-Search: moving per a picture in reverse ), (Stop), (Play), (Pause), (F-Search: moving per a picture), (F-I/Search :moving per I frame unit).
6) speed control : There are [Up], [Down] buttons related speed in the right side of button related play. When it play or play in reverse, it could control the speed and support 1/32, 1/16, 1/8, 1/4, 1/2, 1, 2, 4, 8, 16, 32 times.
3.
2.
4. 4.
If you want to play the recording data, please follow up below step.
1.
1) Select the date in the upper-right side calendar.
2) Select the hour in the hour menu below screen.
3) Select the minute in the minute menu below the application program, then slide bar will be moved to the place.
4) I/Search button, you can find out the nearest I-Frame. Then push the play button.
24
Page 26
MP-840
1.9 <Network Streaming program>
Copy the Driver folder to your remote PC and run NetViewer.exe
You’ll see the network streaming program GUI .
Then , Fill in the IP Address and Push the Connect .
25
Page 27
MP-840
Contact Information
Any advice or comment about our products and service, or anything we can help you please don’t hesitate to contact wit h us. We will do our best to support you for your products, projects and business.
Taiwan Commate Computer Inc.
Address
TEL +886-2-26963909 FAX +886-2-26963911 Website E-Mail
19F, No. 94, Sec. 1, Shin Tai Wu Rd., Shi Chih Taipei Hsien, Taiwan
TUhttp://www.commell.com.twUT TUinfo@commell.com.twUT (General Information)
TUtech@commell.com.twUT (Technical Support)
Commell is the trademark of Taiwan Commate Computer INC.
26
Loading...