COMMELL LV-67E User Manual

Page 1
LV-67E
Mini-ITX motherboard
User’s Manual
Edition: 1.2 2011/02/23
Page 2
LV-67E User’s Manual
Copyright
Copyright 2009. All rights reserved. This document is copyrighted and all rights are reserved. The information in this document is subject to change without prior notice to make improvements to the products. This document contains proprietary information and protect ed by copyright. No part of this document may be reproduced, copied, or translated in any form or any means without prior written permission of the manufacturer. All trademarks and/or registered trademarks contains in this document are propert y of their respective owners.
Disclaimer
The company shall not be liable for any incidental or consequenti al dam ages res ultin g from the performance or use of this product. The company does not issue a warranty of any kind, e xpress or implied, including without limitation implied warranties of merchantability or fitness for a particular purpose. The company has the right to revise the manual or include changes in th e specifications of the product described within it at any time without notice and without obligation to notify any person of such revision or changes.
Trademark
All trademarks are the property of their respective holders.
Any questions please visit our website at TUhttp://www.commell.com.twUT.
2
Page 3
LV-67E User’s Manual
Packing List
Please check package component before you use our products.
Hardware:
LV-67E Mini-ITX motherboard x 1
Cable Kit:
SATA Cable x 1
(OALSATA-L)
DC Power Cable x 1
(OALDC-2)
(OSCREW-8) * 2
ATX Power Output Cable x 1
(OALATX-P3S2)
COM port & Printer Port Cable x 1
(OALES-BKU-3)
I/O Shieldx 1
(OPLATE-LV67E)
3
Page 4
LV-67E User’s Manual
LV-67EH/A/C Heatsink with Fan x 1
(OHS-67EF)
LV-67EG/9 Heatsink x 1
(OHS-67E)
Optional Cable:
Dual COM Port Cable x 1
(OALES-BKU2)
44-pin
44-pin
ATA33 IDE Cable x 1
(OALUDMA33-8)
Other Accessories:
Divers CD (including User’s Manual) x 1
4
USB Cable x 1
(OALUSBA-3)
40-pin
Page 5
LV-67E User’s Manual
Index
Chapter1 <Introduction>....................................................8
1.1 <Product Overview> .............................................................................................8
1.2 <Product Specification>........................................................................................9
1.3 <Block Diagram> ................................................................................................11
1.4 <Mechanical Drawing > ......................................................................................12
Chapter 2 <Hardware Setup> .........................................13
2.1 <Connector Location>......................................................................................... 13
2.2 <Jumper Reference>..........................................................................................15
2.3 <Connector Reference>......................................................................................16
2.3.1 <Internal Connectors>.......................................................16
2.3.2 <External Connectors>......................................................16
2.4 <Memory Setup> ................................................................................................17
2.5 <CMOS & ATX Setup>........................................................................................18
2.6 <Enhanced IDE & CF Interface>.........................................................................19
2.7<Serial A T A Interface>..........................................................................................20
2.8 <Network Interface>............................................................................................21
2.9 <Onboard Display Interface>..............................................................................22
2.9.1 <Analog Display> .............................................................22
2.9.2 <Digital Display Interface>...............................................23
2.10 <Audio Interface>..............................................................................................27
2.11 <GPIO and SMBUS Interface> .........................................................................29
2.12 <USB Interface> ...............................................................................................30
2.13 <Power Supply and Fan Interface>...................................................................32
2.13.1 <Power Input>.................................................................32
2.13.2 <Power Output>..............................................................33
2.13.3 <Fan connector>..............................................................34
2.14 <Serial Port>.....................................................................................................35
2.15 <Switch and Indicator> .....................................................................................38
5
Page 6
LV-67E User’s Manual
Chapter 3 <System Configuration>.................................40
3.1 <Audio Configuration> ........................................................................................40
3.2 <Video Memory Setup>......................................................................................41
3.3 <Display Properties Setting>...............................................................................43
Chapter 4 <BIOS Setup> ................................................46
Appendix A <I/O Port Pin Assignment>...........................48
A.1 < IDE Port >........................................................................................................48
A.2 < Serial ATA Port >..............................................................................................48
A.3 < IrDA Port >.......................................................................................................49
A.4 < GPIO Port >..................................................................................................... 49
A.5 < USB Interface >...............................................................................................49
A.7 < Parallel Port >..................................................................................................53
A.8 < VGA Port >......................................................................................................53
A.9 < LAN Port >.......................................................................................................54
A.10 < SMBus >........................................................................................................54
Appedix B <System Resources>.....................................55
B.1 < I/O Port Address Map >...................................................................................55
B.2 < Memory Address Map >..................................................................................57
B.3 < System IRQ Resources >................................................................................58
B.4 < System DMA Resources >...............................................................................58
Appedix C <Flash BIOS>................................................59
C.1 <BIOS Auto Flash Tool> .....................................................................................59
C.2 <Flash Method> .................................................................................................59
Appendix D <Programming GPIO’s> ..............................60
Appendix E <Watch Dog timer Setting >.........................61
Contact Information.........................................................62
6
Page 7
LV-67E User’s Manual
(This Page is Left for Blank)
7
Page 8
LV-67E User’s Manual
Chapter1 <Introduction>
1.1 <Product Overview>
LV-67EG/A/H/C/9 is the Mini-ITX motherboard with Intel® Atom™ N450/D410/D510/D525
/N455 Processor, integrated GMA3150 graphics, Intel® ICH8-M, DDR2 SO-DIMM memory, Realtek HD Audio, IDE, CF, SATAII and Intel® 82583V Gigabit LAN.
Intel® Atom Processor
The Intel® Atom™ N450/D410/D510/D525/N455 processor supports one channel of 667 MHz DDR2 SDRAM, 512KB/512KB/1MB/1MB/512KB L2 cache, for 45nm proce
-ss technolog-y support Hyper-Threading Technology, the chipset features powereffici­ent graphics with Intel® Graphics Media Accelerator 3150 for an integrated 18-bit 3 D graphics engine. The DMI is designed into the Pineview-M(D) processor to provid e an efficient high-bandwidth communication channel between the processor and the ICH8M.
Embedded Intel® ICH8-M chipset
The board integrates Intel® ICH8M. It provides I/O capabilities and flexibility via high-bandwidth interfaces such as PCIE and Hi-Speed USB 2.0 connectivity. Serial ATA II. IDE, HD Audio.
Flexible Extension Interface
The board provides one PCI-slot for graphics card, it also can support PCI-slot for LAN card or other devices. The board also provides mini-PCI socket, Compact Flash Type II socket and two PCI-E Mini Card socket.
8
Page 9
LV-67E User’s Manual
1.2 <Product Specification>
General Specification
Form Factor Mini-ITX motherboard CPU Intel® Atom N450 / N455 Processor 1.66GHz (LV-67EG / LV-67E9)
Intel® Atom D410 / D510 Processor 1.66GHz (LV-67EH / LV-67EA) Intel® Atom D525 Processor 1.8GHz (LV-67EC) Package type: FCBGA559
Memory 1 x 200-pin DDR2 SO-DIMM 667MHz SDRAM up to
2GB/4GB/4GB/4GB/2GB
(LV-67EG / LV-67EH / LV-67EA / LV-67EC / LV-67E9)
Unbufferred, none-ECC memory supported only Chipset Intel® ICH8M BIOS Phoenix-Award v6.00PG 8Mb SPI flash BIOS Green Function Power saving mode includes doze, standby and suspend modes.
ACPI version 2.0 and APM version 1.2 compliant Watchdog Timer System reset programmable watchdog timer with 1 ~ 255 sec./min.
of timeout value Real Time Clock Intel® ICH8-M built-in RTC with lithium battery Enhanced IDE
Serial ATAII Intel® ICH8M integrates 3 Serial ATAII interfaces
Multi-I/O Port
Chipset Intel® ICH8M with Winbond® W83627DHG-P controller Serial Port Five RS-232 and one RS232/422/485 serial ports USB Port Eight Hi-Speed USB 2.0 ports with 480Mbps of transfer rate IrDA Port One IrDA compliant Infrared interface supports SIR K/B & Mouse External PS/2 keyboard and mouse ports on rear I/O panel GPIO One 12-pin Digital I/O connector with 8-bit programmable I/O I
Smart Fan One CPU fan connectors for fan speed controllable
VGA Display Interface
Chipset Intel® Atom N450 processor (System Controller Hub) (LV-67EG)
Frame Buffer Up to 384MB shared with system memory Display Type CRT, LVDS, LCD monitor with analog display Connector External DB15 female connector on rear I/O panel
9
IDE supports 44-Pin Disk On Module with +5V power supply
One CompactFlash Type II socket on solder side
(No RAID Function)
Up to 300MB/s of transfer rate
nterface
Intel® Atom D410 processor (System Controller Hub) (LV-67EH)
Intel® Atom D510 processor (System Controller Hub) (LV-67EA)
Intel® Atom D525 processor (System Controller Hub) (LV-67EC)
Intel® Atom N455 processor (System Controller Hub) (LV-67E9)
Onboard 20-Pin LVDS and 5-Pin inverter connector
Page 10
LV-67E User’s Manual
Ethernet Interface
Controller 2 x Intel® 82583V Gigabit Ethernet controller Type Triple speed 10/100/1000Base-T
Auto-switching Fast Ethernet
Full duplex, IEEE802.3U compliant Connector Two External RJ45 connectors with LED on rear I/O panel
Audio Interface
Chipset Intel® ICH8M with Realtek ALC888 HD Audio
Intel High Definition Audio compliance Interface 2 channels sound output Connector External 3 phone jack for 2 channel audio on rear I/O panel
External SPDIF connector on rear I/O panel
Internal 10-pin header for line-out, MIC-in, 4-pin header for CD-IN
Expansive Interface
PCI PCI slot (32-bit, 33MHz)
Power supply: +3.3V, +5V, 3VSB +12V, -12V Mini PCI One Mini-PCI socket TYPE III A (32-bit, 33MHz)
Power supply: +3.3V, +5V, 3VSB PCIE mini card Two PCIE mini card socket
Power supply: +1.5V, 3VSB
Power and Environment
Power
Standard 20-pin ATX power supply or 9~24V full range DC Input Requirement Dimension 170 (L) x 170 (H) mm Temperature Operating within 0 ~ 60P
Storage within –20 ~ 85
O
p
C (32 ~ 140P
O
p
P
C (-4 ~ 185P
O
p
F)
O
p
F)
Ordering Code
LV-67EG LV-67EH LV-67EA LV-67EC
Support Intel® Atom N450 / D410 / D510 / D525 /N455 processor
with onboard VGA, LVDS for 18-bits, Audio, Giga LAN, USB2.0,
SATAII, PCIE mini card, PCI, Mini-PCI, Serial Port, CF, SMBUS,
GPIO, IrDA, LPT, CDIN, SPDIF
LV-67E9
The specifications may be different as the actual production. For further product information please visit the website at
TUhttp://www.commell.com.twUT
10
Page 11
LV-67E User’s Manual
1.3 <Block Diagram>
CRT
18bit Single Channel LVDS
3 x Serial ATA II
BIOS
8 x USB2.0 port
W83627DHG-P
Intel® Atom
N450/D410/
D510/D525/N455
ICH8M
DDR2 SO-DIMM 2GB/4GB/ 4GB/4GB/2GB max.
Compact Flash & IDE
2 x PCIE mini card socket
Mini-PCI Slot
PCI Slot
4 x Serial Port
ICHF81216D
ALC888 HD Audio
2 x Serial Port
2 x PCIE Giga LAN
GPIO
IrDA
LPT
Block Diagram 11
Page 12
LV-67E User’s Manual
1.4 <Mechanical Drawing >
Unit: inch
12
Page 13
LV-67E User’s Manual
Chapter 2 <Hardware Setup>
2.1 <Connector Location>
CN_INV
CN_LVDS
CN_USB1/2
Mini-Card1
CPUFAN
CN_12V
ATX
DDRII
SYSFAN
S_ATA1/2/3
JFRNT
CF
IDE
CN DIO CN_IR
Mini-PCI
PCI
CN_LPT
CN_SMBUS
CN_AUDIO
CDIN
CN_COM4
CN_COM5/6
Connector Reference 13
Page 14
LV-67E User’s Manual
Mini-Card2
PS2
COM1 + CRT USB_RJ45_1/2
COM3+COM2
Audio
SPDIF
14
Page 15
LV-67E User’s Manual
2.2 <Jumper Reference>
Jumper Function
JRTC CMOS Operating/Clear Setting JVLCD Panel Voltage Setting JP39 COM3 signal mode switch (For Pin-9) JP49 COM4 signal mode switch (For Pin-9) JAT Power mode select JCSEL1
JCSEL2
CN_COM2 RS-232 RS422 RS485 Setting CN_IR IrDA Setting
JVLCD
JCSEL2
JAT
JCSEL1
JP39/JP49
JRTC
Connector Reference 15
Page 16
LV-67E User’s Manual
2.3 <Connector Reference>
2.3.1 <Internal Connectors>
Connector Function Remark
DDRIII1/2 200 -pin DDR2 SO-DIMM SDRAM slot S_ATAII1/2/3 7-pin Serial ATA II connector IDE 44-pin primary IDE connector CF Compact Flash Type II socket ATX 24-pin power supply connector CN_12V 4-pin +12V additional power supply connector CN_AUDIO 5 x 2-pin audio connector CDIN 4-pin CD-ROM audio input connector CN_DIO 6 x 2-pin digital I/O connector CN_USB1/2 10-pin USB connector CPUFAN 4-pin CPU cooler fan connector SYSFAN 3-pin system cooler fan connector CN_IR 5-pin IrDA connector CN_COM4 5 x 2-pin RS232 CN_COM56 10 x 2-pin 2 x RS232 CN_LPT 13 x 2-pin printer connector CN_SMBUS 5-pin SMBUS connector CN_INV 5-pin LCD inverter connector CN_LVDS 20 x 2-pin LVDS connector JFRNT 14-pin front panel switch/indicator connector PCI 120-Pin PCI socket Mini-PCI 124-pin Mini-P CI socket MINI_CARD1/2 2 x 52-pin PCIE mini card socket
2.3.2 <External Connectors>
Connector Function Remark
PS2 PS/2 Keyboard/Mouse connector CRT+COM1 DB15 VGA + Serial port connector USB_RJ45_1/2 Dual USB and one RJ45 LAN Port COM 2/3 Serial port connector AUDIO Audio connectors SPDIF SPDIF digital audio output connector
16
Page 17
LV-67E User’s Manual
2.4 <Memory Setup>
Non-ECC, unbuffered memory is supported only. LE-67EG/9 provides one 200-pin DDR2 SO-DIMM to support DDR2 667 memory modules support up to 2GB of capacity.
Suggestion:
DDR2 SO-DIMM Modules:Raw Card A = Double-sided x 16 Raw Card C = Single-sided x 16
LV-67EH/A/C provides one 200-pin DDR2 SO-DIMM to support DDR2 667 memory modules support up to 4GB of capacity.
Suggestion:
DDR2 SO-DIMM Modules:Raw Card C = Single -sided x 16 Raw Card D = Single -sided x 8 Raw Card E = Double -sided x 8
.
DDRII
Memory Installation 17
Page 18
LV-67E User’s Manual
2.5 <CMOS & ATX Setup>
The board’s data of CMOS can be setting in BIOS. If the board refuses to boot due to inappropriate CMOS settings, here is how to proceed to clear (reset) the CMOS to its default values.
Jumper: JRTC Type: Onboard 3-pin jumper
JRTC Mode
1-2 Clear CMOS 2-3 Normal Operation
Default setting
Jumper: JAT Type: onboard 3-pin jumper
JAT Mode
1-2 AT Mode 2-3 ATX Mode
Default setting
JAT
3 1
CMOS Setup 18
JRTC
3
1
Page 19
LV-67E User’s Manual
2.6 <Enhanced IDE & CF Interface>
The board supports one enhanced IDE interface for 2 ATAPI devices with ATA33. Based on embedded application, the board has one 44-pin IDE c onnector +5V supported for disk on module. The board also provides a Compact Flash Type II socket.
43
IDE
1
244
CF
19
Page 20
LV-67E User’s Manual
2.7<Serial A TA Interface>
Based on Intel® ICH8M, the board provides Three Serial ATAII interfaces with up to 300MB/s of transfer rate.
S_ATA1/2/3
20
Page 21
LV-67E User’s Manual
2.8 <Network Interface>
The board integrates with two Intel® 82583V Gigabit Ethernet controllers, as the PCI Express bus. The Intel® 82583V supports triple speed of 10/100/1000Base-T, with IEEE802.3 compliance and Wake-On-LAN supported.
LAN1LAN2
LAN Installation 21
Page 22
LV-67E User’s Manual
2.9 <Onboard Display Interface>
Based on Intel® Atom N450/D410/D510/D525/N455 Processor with built-in graphics, the board provides one DB15 Connector on real external I/O port, and One 20-pin LVDS interface with 5-pin LCD backlight inverter connector. The board provides dual display function with clone mode and extended desktop mode for CRT and LVDS.
Notice: When you install any PCI Graphic card, the onboard graphics would be disabled automatically.
2.9.1 <Analog Display>
Please connect your CRT or LCD monitor with DB15 male connector to the onboard DB15 female connector on rear I/O port. LV-67EG/9 supports 1400 x 1050 (WUXGA) resolution displays. LV-67EH/A/C supports 2048 x 1536 (WUXGA) resolution displays.
22
CRT1
Page 23
LV-67E User’s Manual
2.9.2 <Digital Display Interface>
The board provides one 20-pin LVDS connector for 18-bit single channel panels. L V-67EG/9 supports 1280 x 800 (WUXGA) of resolution, and LV -67E/H/A/C supports 1366 x 768 (WUXGA) of resolution, with one LCD backlight inverter connector and one jumper for panel voltage setting.
CN_LVDS
19 20
CN_INV 1
5
1 2
JVLCD
1 3
23
Page 24
LV-67E User’s Manual
Connector: CN_INV Jumper: JVLCD Type: 5-pin Inverter power connector Type: 3-pin Power select jumper Connector model: molex_53261-5pin
Pin Description Pin Description
1 ENABKL 1-2 +5V 2 GND 2-3 +3.3V
3 GND Default: 2-3 4 GND 5 +12V
Connector: CN_LVDS Type: onboard 20-pin connector for LVDS connector Connector model: HIROSE DF13-20DP-1.25V
Pin Signal Pin Signal
2 LCDVCC 1 LCDVCC 4 GND 3 GND 6 TXL0P 5 TXL0N
8 TXL1N 7 GND 10 GND 9 TXL1P 12 TXL2P 11 TXL2N 14 TXLCKN 13 GND 16 GND 15 TXLCKP 18 SMBDATA 17 SMBCLK 20 SPDIFO 19 GND
24
Page 25
LV-67E User’s Manual
To setup the LCD, you need the component below:
1. A panel with LVDS interfaces.
2. An inverter for panel’s backlight power.
3. A LCD cable and an inverter cable.
For the cables, please follow the pin assignm ent of the connector to make a cable, because every panel has its own pin assignment, so we do not provide a standard cable; please find a local cable manufacture to make cables.
LCD Installation Guide:
1. Preparing the LV-67E, LCD panel and the backlight inverter.
2. Please check t he datasheet of the panel to see the voltage of the panel, and set the jumper JVLCD to +5V or +3.3V.
3. You would need a LVDS type cable.
Panel side
For sample illustrator only
4. To connect all of the devices well.
Board side
25
Page 26
LV-67E User’s Manual
After setup the devices well, you need to select the LCD panel type in the BIOS.
The panel type mapping is list below:
LV-67E BIOS panel type selection form
On board Single channel LVDS
18bit
NO. Output format
1 640 x 480 2 800 x 480 3 800 x 600 4 1024 x 600 5 1024 x 768 6 1280 x 768
26
Page 27
LV-67E User’s Manual
2.10 <Audio Interface>
The board integrates onboard audio interface with REALTEK ALC888 codec, with Intel next generation of audio standard as High Definition Audio, it offers more vivid sound and oth er advantages than former HD audio compliance. The main specifications of ALC888 are:
z High-performance DACs with 100dB S/N ratio z 2 DAC channels support 16/20/24-bit PCM format for 2 audio solution z 16/20/24-bit S/PDIF-OUT supports 44.1K/48K/96kHz sample rate z Compatible with HD z Meets Microsoft WHQL/WLP 2.0 audio requirements
The board provides 2 channels audio phone jacks on rear I/O port, Line-in/MIC-in ports for front I/O panel through optional cable.
CN_AUDIO
9
10
CDIN
4
1
1
2
27
Page 28
LV-67E User’s Manual
Connector: CN_AUDIO
Type: 10-pin (2 x 5) header (pitch = 2.54mm)
Pin Description Pin Description
1 MIC_L 2 Ground 3 MIC_R 4 N/C 5 LINE_OUT_R 6 MIC Detect 7 SENSE 8 N/C 9 LINE_OUT_L 10 Speaker Detect
Connector: CDIN
Type: 4-pin header (pitch = 2.54mm)
Pin Description
1 CD – Left 2 Ground 3 Ground 4 CD – Right
SPDIF
LINE-IN LINE-OUT MIC-IN
Rear I/O phone jacks
28
Page 29
LV-67E User’s Manual
2.11 <GPIO and SMBUS Interface>
The board provides a programmable 8-bit digital I/O interface, and a SMBUS (System management bus) interface for control panel application.
Connector: CN_DIO Type: onboard 2 x 6-pin header, pitch=2.0mm
Pin Description Pin Description
1 Ground 2 Ground 3 GP10 4 GP14 5 GP11 6 GP15 7 GP12 8 GP16 9 GP13 10 GP17 11 VCC 12 +12V
Connector: CN_SMBUS Type: 5-pin header for SMBUS Ports
Pin Description
1 VCC 2 N/C 3 SMBDATA 4 SMBCLK 5 Ground
CN_DIO
11
12
2
CN_SMBUS
5 1
1
29
Page 30
LV-67E User’s Manual
2.12 <USB Interface>
LV-67E integrates eight USB2.0 ports. The specifications of USB2.0 are listed below:
Interface USB2.0
Controller
Transfer Rate Up to 480Mb/s
Voltage 5V
The Intel® ICH8-M contains two Enhanced Host Controller Interface (EHCI) and five Universal Host Controller Interfaces (UHCI), it can determine whether your connected device is for USB1.1 or USB2.0, and change the transfer rate automatically.
USB5/6/7/8
Intel® ICH8-M
30
Page 31
LV-67E User’s Manual
Connector: CN_USB1/2 Type: 10-pin (5 x 2) header for USB5/6 Ports
Pin Description Pin Description
1 VCC 2 VCC 3 Data0- 4 Data1­5 Data0+ 6 Data1+ 7 Ground 8 Ground 9 Ground 10 N/C
CN_USB1/2
1 9
2 10
31
Page 32
LV-67E User’s Manual
2.13 <Power Supply and Fan Interface>
2.13.1 <Power Input>
The board requires onboard 4-pin DC-input conn ector voltage range is from 8V to 24V, or onboard 20-pin ATX2.0, for the input current, please take a reference of the power consumption report on appendix.
Connector: ATX (It also can become Output when DC-IN be used) Type: 20-pin ATX power connector
Pin Assignment Pin Assignment
1 3.3V 11 3.3V 2 3.3V 12 -12V 3 GND 13 GND 4 5V 14 -PSON 5 GND 15 GND 6 5V 16 GND 7 GND 17 GND 8 PW_OK 18 N/C 9 5V_SB 19 5V
10 12V 20 5V
Connector: DC_IN Type: 4-pin standard Pentium 4 additional +9~24V power connector
Pin Description Pin Description
1 Ground 2 Ground 3 +9~24V 4 +9~24V
20
10
4 3
2
ATX
11
1
DC_IN
1
Page 33
LV-67E User’s Manual
2.13.2 <Power Output>
The board provides one 20-pin ATX connector for +5V/+12V output for powering your HDD, CDROM or other devices.
Attention: When DC-IN had power supplied, the ATX become output !
Avoid DC-IN and ATX power supply input at the same time !
Connector: ATX (When DC-IN be used) Type: 20-pin ATX connector for +3.3V/+5V/+12V Output
Pin Assignment Pin Assignment
1 3.3V 11 3.3V 2 3.3V 12 * 3 * 13 * 4 5V 14 * 5 GND 15 * 6 * 16 GND 7 GND 17 GND 8 * 18 * 9 * 19 5V
10 12V 20 5V
Note: Maximum output voltage: 12V/2A & 5V/3A &3.3V/2A
ATX
-
33-
Page 34
LV-67E User’s Manual
2.13.3 <Fan connector>
The board provides one 4-pin fan connectors supporting smart fan for CP U cool er and one
3-pin cooler fan connectors for system.
SYSFAN
CPUFAN
4
Connector: CPUFAN Type: 4-pin fan wafer connector
Pin Description Pin Description
1 Ground 2 +12V 3 Fan Speed Detection 4 Fan Control
Connector: SYSFAN Type: 3-pin fan wafer connector
Pin Description Pin Description Pin Description
1 Ground 2 +12V 3 Sense
3 1
34
Page 35
LV-67E User’s Manual
2.14 <Serial Port>
The board supports Three RS232 serial port and one jumper selectable RS232/422/485 serial ports. The jumper JCSEL1 & JCSEL2 can let you configure the communicating modes for COM2.
Connector: COM2 Type: 9-pin D-sub male connector on bracket for COM2
Pin Description Pin Description
1 DCD/422TX-/485- 2 RXD/422TX+/485+ 3 TXD/422RX+ 4 DTR/422RX­5 GND 6 DSR 7 RTS 8 CTS 9 RI 10 N/C
COM1 COM3
COM2
35
Page 36
LV-67E User’s Manual Setting RS-232 & RS-422 & RS-485 for COM2
CN_COM5/6
19 1
20 2
CN_COM4
9
10
1
2
JCSEL1
11
12
JP39/JP49
JCSEL2
7
1
2
1
2 8
36
Page 37
LV-67E User’s Manual
Function JCSEL2 JCSEL1
IrDA
RS-422
RS-485
RS-232
Default setting:
JCSEL1: (1-3, 2-4, 7-9, 8-10) JCSEL2: (1-2)
Jumper: JP39/JP49 (COM3/4) Type: onboard 6-pin header
7
1
2 8
7
1
2 8
1
7
2 8
1
7
2 8
11
12
11
12
11
12
11
12
1
2
1
2
1
2
1
2
Power Mode JP39/JP49
Pin 9 with 5V Power 1-2
Pin 9 with 12V Power 3-4
Default setting: 5-6
5 1
6 2
5 1
6 2
37
Page 38
LV-67E User’s Manual
2.15 <Switch and Indicator>
The JFRNT provides front control panel of the board, such as power button, reset and beeper, etc. Please check well before you connecting the cables on the chassis.
Connector: JFRNT Type: onboard 14-pin (2 x 7) 2.54-pitch header
Function Signal PIN Signal Function
IDE LED
Reset
Power
Button
HDLED+ 1 2 PWDLED+
HDLED- 3 4 N/C
Reset+ 5 6 PWDLED-
Reset- 7 8 SPKIN+
N/C 9 10 N/C
PWRBT+ 11 12 N/C
PWRBT- 13 14 SPKIN-
Power
LED
Speaker
14
2
JFRNT
13
1
38
Page 39
LV-67E User’s Manual
(This Page is Left for Blank)
39
Page 40
LV-67E User’s Manual
Chapter 3 <System Configuration>
3.1 <Audio Configuration>
The board integrates Intel® ICH8-M with REALTEK® ALC888 codec. It can support 2-channel sound under system configuration. Please follow the steps below to setup your sound system.
1. Install REALTEK HD Audio driver.
2. Lunch the control panel and Sound Effect Manager.
3. Select Speaker Configuration
4. Select the sound mode to meet your speaker system.
40
Page 41
LV-67E User’s Manual
3.2 <Video Memory Setup>
Based on Intel® Atom N450/D410/D510/D525/N455 chipset with GMA (Graphic Media Accelerator) 3150, the board supports Intel® DVMT (Dynamic Video Memory Technology)
3.0, which would allow the video memory be triggered up to 384MB.
To support DVMT, you need to install the Intel GMA3150 Driver with supported OS.
BIOS Setup: On-Chip Frame Buffer Size:
This item can let you select video memory which been allocated for legacy VGA and SVGA graphics support and compatibility. The available option is 1MB and 8MB.
41
Page 42
LV-67E User’s Manual Total GFX Memory Size:
This item can let you select a static amount of page-locked graphics memory; which will be allocated during driver initialization. Once you select the memory amount, it will be no longer available for system memory.
DVMT Memory Size:
This item can let you select a maximum size of dynamic amount usage of video memory, the system would configure the video memory depends on your appl ication, this item is strongly recommend to be selected as MAX DVMT.
Fixed + DVMT Memory Size:
You can select the fixed amount and the DVMT amount at the same time for a guarantee d video memory and additional dynamic video memory Notice:
1. The On-Chip Frame Buffer Size would be included in the Total GFX Memory Size.
42
Page 43
LV-67E User’s Manual
3.3 <Display Properties Setting>
Based on Intel® Atom N450/D410/D510/D525/N455 with GMA3150 (Graphic Media Accelerator), the board supports two DACs for display device as different resolution and color bit. Please install the Intel Graphic Driver before you starting setup display devices.
1. Click right button on the desktop to lunch display properties
2. Click Advanced button for more specificity setup.
43
Click Graphics Properties... for advanced setup
Page 44
LV-67E User’s Manual
3. This setup options can let you define each device settings.
Set the main display device here
Choose Intel® Dual
Display Clone to
setup the dual display mode as same screen
44
Page 45
LV-67E User’s Manual
Choose Extended
Desktop to setup
the dual display mode as different screen display
Choose Monitor to setup the CRT monitor for Colors, Resolution and Refresh Rate
45
Page 46
LV-67E User’s Manual
Chapter 4 <BIOS Setup>
The motherboard uses the Award BIOS for the system configuration. The Award BIOS in the single board computer is a customized version of the industrial standard BIOS for IBM PC AT-compatible computers. It supports Intel® x86 and compatible CPU architecture based processors and computers. The BIOS provides critical low-level support for the system central processing, memory and I/O sub-systems.
The BIOS setup program of the single board computer let the customers modify the basic configuration setting. The settings are stored in a dedicated battery-backed memory, NVRAM, retains the information when the power is turned off. If the battery runs out of the power, then the settings of BIOS will come back to the default setting.
The BIOS section of the manual is subject to change without notice and is provided here for reference purpose only. The settings and configurations of the BIOS are current at the time of print, and therefore they may not be exactly the same as that displayed on your screen.
To activate CMOS Setup program, press <DEL> key i mmediately after you turn on the system. The following message “Press DEL to enter SETUP” should appear in the lower left hand corner of your screen. When you enter the CMOS Setup Utility, the Main Menu will be displayed as Figure 4-1. You can use arrow keys to select your function, press Enter key to accept the selection and enter the sub-menu.
Figure 4-1 CMOS Setup Utility Main Screen
46
Page 47
LV-67E User’s Manual
(This Page is Left for Blank)
47
Page 48
LV-67E User’s Manual
Appendix A <I/O Port Pin Assignment>
A.1 < IDE Port >
Connector: IDE Type: 44-pin (22 x 2) box header
Pin Description Pin Description
1 Reset 2 Ground 3 D7 4 D8 5 D6 6 D9 7 D5 8 D10 9 D4 10 D11 11 D3 12 D12 13 D2 14 D13 15 D1 16 D14 17 D0 18 D15 19 Ground 20 N/C 21 REQ 22 Ground 23 IOW-/STOP 24 Ground 25 IOR-/HDMARDY 26 Ground 27 IORDY/DDMARDY 28 Ground 29 DACK- 30 Ground 31 IRQ 32 N/C 33 A1 34 SD 35 A0 36 A2 37 CS1 38 CS3 39 ASP1 40 Ground 41 Vcc 42 Vcc 43 Ground 44 Ground
43
44
1
2
A.2 < Serial ATA Port >
Connector: S_ATA1/2/3 Type: 7-pin wafer connector
1 2 3 4 5 6 7
GND RSATA_TXP1 RSATA_TXN1 GND RSATA_RXN1 RSATA_RXP1 GND
48
17
Page 49
LV-67E User’s Manual
A.3 < IrDA Port >
Connector: CN_IR Type: 5-pin header for SIR Ports
Pin Description
1 VCC 2 N/C 3 IRRX 4 Ground 5 IRTX
1
5
A.4 < GPIO Port >
Connector: CN_DIO Type: onboard 2 x 6-pin header, pitch=2.0mm
Pin Description Pin Description
1 Ground 2 Ground 3 GP10 4 GP14 5 GP11 6 GP15 7 GP12 8 GP16 9 GP13 10 GP17 11 VCC 12 +12V
A.5 < USB Interface >
Connector: CN_USB1/2 Type: 10-pin (5 x 2) header for dual USB Ports
Pin Description Pin Description
1 VCC 2 VCC 3 Data0- 4 Data1­5 Data0+ 6 Data1+ 7 Ground 8 Ground 9 Ground 10 N/C
12
9
10
11
1
2
1
2
49
Page 50
LV-67E User’s Manual
A.6 < Serial Port >
Connector: COM1/2/3 Type: 9-pin D-sub male connector on bracket
Pin Description Pin Description
1 DCD/422TX-/485- 2 RXD/422TX+/485+ 3 TXD/422RX+ 4 DTR/422RX­5 GND 6 DSR 7 RTS 8 CTS 9 RI 10 N/C
Setting RS-232 & RS-422 & RS-485 for COM2
1 2 3 4 5
6 7 8 9
JCSEL1
11
1
50
CN_COM5/6
19 1
20 2
CN_COM4
9
10
12
JP39/JP49
JCSEL2
7
1
2
2
1
2 8
Page 51
LV-67E User’s Manual
Function JCSEL2 JCSEL1
IrDA
RS-422
RS-485
RS-232
Default setting:
JCSEL1: (1-3, 2-4, 7-9, 8-10) JCSEL2: (1-2)
Jumper: JP39/JP49 (COM3/4) Type: onboard 6-pin header
7
1
2 8
7
1
2 8
1
7
2 8
1
7
2 8
11
12
11
12
11
12
11
12
1
2
1
2
1
2
1
2
Power Mode JP39/JP49
Pin 9 with 5V Power 1-2
Pin 9 with 12V Power 3-4
Default setting: 5-6
5 1
6 2
5 1
6 2
51
Page 52
LV-67E User’s Manual
Connector: CN_COM4 Type: 10-pin (5 x 2) header
Pin Description Pin Description
1 DCD 2 RXD 3 TXD 4 DTR 5 GND 6 DSR 7 RTS 8 CTS 9 RI 10 N/C
Connector: CN_COM5/6 Type: 20-pin (10x2) header
Pin Description Pin Description
1 MDCD1 2 MSIN1 3 MSO1 4 MDTR1 5 GND 6 MDSR1 7 MRTS1 8 MCTS1 9 MRI1 10 NC 11 MDCD2 12 MSIN2 13 MSO2 14 MDTR2 15 GND 16 MDSR2 17 MRTS2 18 MCTS2 19 MRI2 20 NC
9 1
10 2
19 1
20 2
52
Page 53
LV-67E User’s Manual
A.7 < Parallel Port >
13 1
Connector: CN_LPT Type: 26-Pin box header Connector on bracket
26 14
Pin Assignment Pin Assignment
1 -PSTB 14 AFD­2 PRO0 15 ERR­3 PRO1 16 INT­4 PRO2 17 SLIN­5 PRO3 18 Ground 6 PRO4 19 Ground 7 PRO5 20 I/O Ground 8 PRO6 21 Ground 9 PRO7 22 Ground 10 ACK- 23 Ground 11 BUSY 24 Ground 12 PE 25 Ground 13 SLCT 26 N/C
A.8 < VGA Port >
Connector: CRT1 Type: 15-pin D-sub female connector on bracket
Pin Description Pin Description Pin Description
1 RED 6 Ground 11 N/C 2 GREEN 7 Ground 12 DDC_DA 3 BLUE 8 Ground 13 HSYNC 4 N/C 9 +5V 14 VSYNC 5 Ground 10 Ground 15 DDC_CLK
6
1 2 3 4 5
10
11 12 13 14 15
53
Page 54
LV-67E User’s Manual
A.9 < LAN Port >
Connector: RJ45_1/2 Type: RJ45 connector with LED on rear panel
Pin 1 2 3 4 5 6 7 8
Description TRD0+ TRD0- TRD1+ TRD2+ TRD2- T RD1- T RD3+ T RD3-
8 1
A.10 < SMBus >
Connector: CN_SMBUS Type: 4-pin SMBus connector
Pin Description Pin Description
1 VCC 2 N/C 3 SMBDATA 4 SMBCLK 5 Ground
1 5
54
CN_SMBUS
5 1
Page 55
LV-67E User’s Manual
Appedix B <System Resources>
B.1 < I/O Port Address Map >
55
Page 56
LV-67E User’s Manual
56
Page 57
LV-67E User’s Manual
B.2 < Memory Address Map >
57
Page 58
LV-67E User’s Manual
B.3 < System IRQ Resources >
B.4 < System DMA Resources >
58
Page 59
LV-67E User’s Manual
Appedix C <Flash BIOS>
C.1 <BIOS Auto Flash Tool>
The board is based on Award BIOS and can be updated easily by the BIOS auto flash tool. You can download the tool online at the address below:
TUhttp://www.award.comUT TUhttp://www.commell.com.tw/support/support.htmUT
File name of the tool is “awdflash.exe”, it’s the utility that can write the data into the BIOS flash ship and update the BIOS.
C.2 <Flash Method>
1. Please make a bootable floppy disk.
2. Get the last .bin files you want to update and copy it into the disk.
3. Copy awardflash.exe to the disk.
4. Power on the system and flash the BIOS. (Example: C:/ awardflash XXX.bin)
5. Re-star the system.
Any question about the BIOS re-flash please contact your distributors or visit the web-site at below:
http://www.commell.com.tw/support/support.htm
59
Page 60
LV-67E User’s Manual
Appendix D <Programming GPIO’s>
The GPIO’can be programmed with the MSDOS debug program using simple IN/OUT commands.The following lines show an example how to do this.
GPIO0…..GPIO7 bit0……bit7
-o 2E 87 ;enter configuration
-o 2E 87
-o 2E 07
-o 2F 09 ;enable GPIO function
-o 2E 30
-o 2F 02 ;enable GPIO configuration
-o 2E F0
-o 2F xx ;set GPIO as input/output; set ‘1’ for input,’0’for output
-o 2E F1
-o 2F xx ;if set GPIO’s as output,in this register its value can be set
Optional :
-o 2E F2
-o 2F xx ; Data inversion register ; ‘1’ inverts the current valus of the bits ,’0’ leaves them as they are
-o 2E 30
-o 2F 01 ; active GPIO’s
For further information ,please refer to Winbond W83627DHG-P datasheet.
60
Page 61
LV-67E User’s Manual
Appendix E <Watch Dog timer Setting >
The watchdog timer makes the system auto-reset while it stops to work for a period. The integrated watchdog timer can be setup as system reset mode by program.
Timeout Value Range
- 1 to 255
- Second or Minute
Program Sample
Watchdog timer setup as system reset with 5 second of timeout
2E, 87 2E, 87 2E, 07 2F, 08 Logical Device 8 2E, 30 Activate 2F, 01 2E, F5 Set as Second* 2F, 00 2E, F6 Set as 5 2F, 05
* Minute: bit 3 = 0; Second: bit 3 = 1
You can select Timer setting in the BIOS, after setting the time options, the system will reset according to the period of your selection.
61
Page 62
LV-67E User’s Manual
Contact Information
Any advice or comment about our products and service, or anything we can help you please don’t hesitate to contact with us. We will do our best to support you for your products, projects and business.
Taiwan Commate Computer Inc.
19F., No.94, Sec. 1, Xintai 5th Rd., Xizhi Dist., New Taipei City
Address
TEL +886-2-26963909 FAX +886-2-26963911
22102, Taiwan
Website
E-Mail
Facebook
Twitter https://twitter.com/Taiwan_Commate
TUhttp://www.commell.com.twUT TUinfo@commell.com.twUT (General Information)
TUtech@commell.com.twUT (Technical Support)
https://www.facebook.com/pages/Taiwan-Commate-Computer-Inc/547993955271899
Commell is a brand name of Taiwan commate computer Inc.
62
Loading...