COMMELL LV-67A User Manual

Page 1
LV-67A
Mini-ITX motherboard
User’s Manual
Edition: 1.5
2011/9/27
Page 2
LV-67A User’s Manual
Copyright
Copyright 2009. All rights reserved. This document is copyrighted and all rights are reserved. The information in this document is subject to change without prior notice to make improvements to the products. This document contains proprietary information and protect ed by copyright. No part of this document may be reproduced, copied, or translated in any form or any means without prior written permission of the manufacturer. All trademarks and/or registered trademarks contains in this document are propert y of their respective owners.
Disclaimer
The company shall not be liable for any incidental or consequenti al dam ages res ultin g from the performance or use of this product. The company does not issue a warranty of any kind, e xpress or implied, including without limitation implied warranties of merchantability or fitness for a particular purpose. The company has the right to revise the manual or include changes in th e specifications of the product described within it at any time without notice and without obligation to notify any person of such revision or changes.
Trademark
All trademarks are the property of their respective holders.
Any questions please visit our website at TUhttp://www.commell.com.twUT.
2
Page 3
LV-67A User’s Manual
(
)
Packing List
Please check package component before you use our products.
Hardware:
LV-67A Mini-ITX motherboard x 1
Cable Kit:
SATA Cable x 2 (OALSATA-L)
USB Cable x 1 (OALUSBA-1)
DVI module with bracket x 1 (BADPDVI2P_A & OALDVI-P)
(LV-67AD2 Only)
26-pin Slim Type Floppy Cable x 1
COM Port Cable x 1
(OAL1S)
(OALFD/NB)
VGA Cable x 1 (LV-67AT only)
OAL-10PCRT
DVI module with bracket x 1 (BADPDVIP_A & OALDVI-P)
(LV-67AD Only)
I/O Shield x 1 (OPLATE-67A)
Other Accessories:
Divers CD (including User’s Manual) x 1
3
Page 4
LV-67A User’s Manual
Index
Chapter1 <Introduction>.........................................................................................7
1.1 <Product Overview>.................................................................................7
1.2 <Product Specification>...........................................................................8
1.3 <Block Diagram>....................................................................................10
1.4 <Mechanical Drawing >.......................................................................... 11
Chapter 2 <Hardware Setup>...............................................................................12
2.1 <Connector Location>............................................................................12
2.2 <Jumper Reference> .............................................................................13
2.3 <Connector Reference>.........................................................................14
2.3.1 <Internal Connectors>................................................................14
2.3.2 <External Connectors>............................................................... 14
2.4 <CPU and Memory Setup>.................................................................... 15
2.4.1 <CPU installation>......................................................................15
2.4.2 <Memory installation> ................................................................16
2.5 <CMOS Setup>......................................................................................18
2.6 <Serial ATA installation>.........................................................................19
2.7 <Floppy Installation>..............................................................................20
2.8 <LAN installation>..................................................................................21
2.9 <Onboard Display Interface>.................................................................22
2.9.1 <Analog Display> .......................................................................22
2.9.2 <L VDS Display LV-67AX Only >.................................................23
2.9.3 <DVI Display LV-67AD and LV-67AD2>.....................................26
2.10 <Audio Installation>..............................................................................27
2.11 <GPIO and SMBUS interface>............................................................. 29
2.12 <USB Installation>................................................................................30
2.13 <Power and Fan Installation> ..............................................................32
2.14 <Serial Port> ........................................................................................34
2.15 <Switch and Indicator>.........................................................................37
4
Page 5
LV-67A User’s Manual
Chapter 3 <System Configuration> ......................................................................39
3.1 <SATA configuration>.............................................................................39
3.2 <SATA RAID Configuration> ..................................................................40
3.3 <Audio Configuration> ...........................................................................44
3.4 <Video Memory Setup> ......................................................................... 45
3.5 <Display Properties Setting>..................................................................47
Chapter 4 <BIOS Setup>......................................................................................49
Appendix A <I/O Port Pin Assignment> ................................................................51
A.1 <Serial ATA Port>...................................................................................51
A.2<Floppy Port> .........................................................................................51
A.3 <IrDA Port>............................................................................................52
A.5 <VGA Port>............................................................................................53
A.6 <LAN Port>............................................................................................53
Appedix B <System Resources>..........................................................................54
B.1 <I/O Port Address Map>........................................................................54
B.2 <Memory Address Map>........................................................................56
B.3 <System IRQ Resources>.....................................................................57
Appedix C <Flash BIOS>......................................................................................58
C.1 <BIOS Auto Flash Tool> ........................................................................58
C.2 <Flash Method>.....................................................................................58
Appendix D <Programming GPIO’s>....................................................................59
Appendix E <Watch Dog timer Setting >..............................................................60
Contact Information...............................................................................................61
5
Page 6
LV-67A User’s Manual
(This Page is Left for Blank)
6
Page 7
LV-67A User’s Manual
Chapter1 <Introduction>
1.1 <Product Overview>
LV-67A is the motherboard with last Intel desktop technology with Mini-ITX form factor.
Based on Intel® Q45 and ICH10DO, the board integrates a new Core 2 Quad / Core 2 Duo Celeron processor 775-pin socket, DDR3 memory socket, Intel® Graphic Media Accelerator 4500 technology, Serial ATA II with RAID function for a powerful desktop system.
Intel
® LGA775 processor
The Intel® Core 2 Quad / Core 2 Duo / Celeron processor now comes with a new form factor with 775-pin PLGA package, for 800/1066/1333MHz front-side-bus, 12MB L2 cache, for 65nm and 45nm manufacturing technology, the PLGA processor without pin header on solder side can make user installing the processor on the socket easier.
Intel
® Q45 and ICH10DO chipset
The Intel Q45 integrates DDR3 800/1066MHz for memory, and Graphic Media Accelerator (GMA) 4500 technology for new graphic engine. It can provide up to 1024MB of frame buffer when you install over 1GB of system memory. The ICH10DO integrates with up to 8 USB2.0 interfaces, and serial ATA II interface with RAID function.
Flexible Extension Interface
The board provides one PCI-slot for graphics card, it also can support PCI-slot for LAN card or other devices. The board also provides mini-PCI socket.
7
Page 8
LV-67A User’s Manual
1.2 <Product Specification>
General Specification
Form Factor Mini-ITX motherboard CPU Intel® Core 2 Quad / Core 2 Duo / Celeron processor
With LGA775 socket Package type: PLGA 775 Front side bus: 800/1066/1333MHZ (200/266/333MHz x 4)
Memory 2 x 240-pin DDR3 800/1066MHz SDRAM up to 4GB
Unbufferred, none-ECC memory supported only Chipset Intel® Q45 (Northbridge) and ICH10DO (Southbridge) BIOS Phoenix-Award v6.00PG 8Mb SPI flash BIOS Green Function Power saving mode includes doze, standby and suspend modes.
ACPI version 1.0 and APM version 1.2 compliant Watchdog Timer System reset programmable watchdog timer with 1 ~ 255 sec./min.
of timeout value Real Time Clock Intel® ICH10DO built-in RTC with lithium battery Serial ATAII Intel® ICH10DO integrates 6 Serial ATA II interface
RAID 0, 1,5,10 Intel Matrix Storage Technology supported
Multi-I/O Port
Chipset Intel® 82801HDO( ICH10DO) with Winbond® W83627DHG
Controller Serial Port Three RS-232 and one RS232/422/485 serial ports USB Port Eight Hi-Speed USB 2.0 ports with 480Mbps of transfer rate Floppy Port One slim type Floppy port IrDA Port One IrDA compliant Infrared interface supports SIR K/B & Mouse External PS/2 keyboard and mouse ports on rear I/O panel GPIO One 12-pin Digital I/O connector with 8-bit programmable I/O
Interface Smart Fan One CPU fan connectors for fan speed controllable
VGA Display Interface
Chipset Intel® Q45 GMA4500 (Graphic Memory Controller Hub) Frame Buffer Up to 1024MB shared with system memory Display Type CRT, LCD monitor with analog display
Onboard 18/24-bit dual channel LVDS interface (LV-67AX)
Onboard DVI interface (LV-67AD/LV-67AD2)
Optional Secondary CRT Connector (LV-67AT) Connector External DB15 female connector on rear I/O panel
Onboard 40-pin LVDS connector (LV-67AX)
Onboard 26-pin DVI Connector (LV-67AD/L-67AD2)
Onboard 10-pin CRT2 Connector (LV-67AT)
8
Page 9
LV-67A User’s Manual
Ethernet Interface
Controller Two Intel 82574L Gigabit Ethernet controller Type Triple speed 10/100/1000Base-T
Auto-switching Fast Ethernet
Full duplex, IEEE802.3U compliant Connector Two External RJ45 connectors with LED on rear I/O panel
Audio Interface
Chipset Intel® ICH10DO with Realtek ALC888HD Audio
Intel High Definition Audio compliance Interface 2 channels sound output Connector External 3 phone jack for 2 channel audio on rear I/O panel
External SPDIF connector on rear I/O panel
Internal 10-pin header for line-out, MIC-in, 4-pin header for CD-IN
Expansive Interface
Mini PCI One Mini-PCI socket TYPE III A (32-bit, 33MHz)
Power supply: +3.3V, +5V
Power and Environment
Power Requirement Dimension 170 (L) x 170 (H) mm Temperature Operating within 0 ~ 60P
Standard ATX 24-pin (20-pin is compatible) power supply
Additional +12V 4-pin power connector
Storage within –20 ~ 85
O
p
C (32 ~ 140P
O
p
P
C (-4 ~ 185P
O
p
F)
O
p
F)
Ordering Code
LV-67AD Onboard VGA, 2 x Intel® Gigabit LAN, 8 x USB2.0, Mini-PCI PCI,
4 x serial Port, 1 x FDD, Realtek ALC888 HD Audio
6 x SATA, 1 x IrDA, 1x DVI Interface
LV-67AD2 Same as LV-67AD with secondary DVI Interface LV-67AX Same as LV-67AD with 18/24-bits LVDS instead of DVI LV-67AT Same as LV-67AD with secondary CRT instead of DVI
The specifications may be different as the actual production.
9
Page 10
LV-67A User’s Manual
1.3 <Block Diagram>
Intel Core 2 Quad / Core Due with 775 Pin PLGA
CRT1
DVI
LVDS
CRT2
8 x USB2.0 ports
HD Audio
2 x Serial ports
1 x Floppy port
CH7318
CH7308
CH7317
Intel Q45
ICH10DO
SPI
2 x 240-pin DDR3 800/1066MHz up to 4GB
6 x Serial ATAII ports
Intel 82574L
2 x GLAN
Mini-PCI slot
PCI Slot
PCI bus
8-bit GPIO
IrDA
BIOS
COM3/4
10
Page 11
LV-67A User’s Manual
1.4 <Mechanical Drawing >
Unit: inch
11
Page 12
LV-67A User’s Manual
Chapter 2 <Hardware Setup>
2.1 <Connector Location>
ATX
DDRIIIA/B
CN_SMBUS
CN_USB4
CPUFAN
CN_12V
JP1/JP2
CN_DVI1
JFRNT
SYSFAN CN_USB
S_ATA1~6
FDD
PCI
CN_DIO
CN_IR
CN_DVI2
JAT
Mini-PCI
CN_AUDIO
CDIN
CN_COM4
JCSEL1
JCSEL2
Audio
PS2
COM1 + CRT USB_RJ45_1/2
COM2+COM3
SPDIF
12
Page 13
LV-67A User’s Manual
2.2 <Jumper Reference>
Jumper Function
JRTC CMOS Operating/Clear Setting JVLCD Panel Voltage Setting (LV-67AX) JP1 COM1 signal mode switch (For Pin-1 & Pin-9) JP2 COM2 signal mode switch (For Pin-1 & Pin-9) JAT Power mode select JCSEL1
JCSEL2
CN_COM2 RS-232 RS422 RS485 Setting CN_IR IrDA Setting
Jumper: JAT
JAT
3 1
Type: Onboard 3-pin jumper
JAT Mode
1-2 AT Power mode 2-3 ATX Power mode
Default setting
13
Page 14
LV-67A User’s Manual
2.3 <Connector Reference>
2.3.1 <Internal Connectors>
Connector Function Remark
CPU LGA775 CPU socket DDRIII1/2 240 –pin DDR2 SDRAM DIMM socket FDD 26-pin slim type floppy connector S_ATAII1/2/3/4/5/6 7-pin Serial ATA II connector ATX 24-pin power supply connector CN_12V 4-pin +12V additional power supply connector CN_AUDIO 5 x 2-pin audio connector CDIN 4-pin CD-ROM audio input connector CN_DIO 6 x 2-pin digital I/O connector CN_USB1/4 10-pin USB connector CPUFAN 4-pin CPU cooler fan connector SYSFAN 3-pin system cooler fan connector NBFAN 3-pin Northbridge cooler fan connector CN_IR 5-pin IrDA connector CN_SMBUS 5-pin SMBUS connector CN_INV 5-pin LCD inverter connector LV-67AX CN_LVDS 20 x 2-pin LVDS connector LV-67AX JFRNT 14-pin front panel switch/indicator connector PCI1 120-Pin PCI socket Mini-PCI 1 x Mini-PCI socket CN_DVI1 26-Smd Pin connector LV-67AD CN_DVI2 26-Pin connector LV-67AD2 CN_CRT 10-Pin connector LV-67AT CN_COM2 5 x 2-pin com connector
2.3.2 <External Connectors>
Connector Function Remark
PS2 PS/2 Keyboard /Mouse connector CRT+COM1 DB15 VGA + Serial port connector USB_RJ45_1/2 Dual USB and one RJ45 LAN Port COM 2/3 Serial port connector AUDIO Audio connectors SPDIF SPDIF digital audio output connector
14
Page 15
LV-67A User’s Manual
p
2.4 <CPU and Memory Setup>
2.4.1 <CPU installation>
LV-67A has a LGA775 CPU socket onboard; please check following steps to install the
processor properly.
Attention If LV-67A need RMA please Keep CPU socket cover on the CPU Socket. Warning If CPU Socket internal Pin damage We could not provide warranty.
Intel® Quad Core 2 Quad / Core 2 Duo Cleron processor Package type: 775 pin PLGA FSB:/800/1066/1333MHz Manufacturing: 65nm / 45nm Intel Hyper Threading Technology and
1. Lift this bar
Core 2 Duo Quad / Duo supported
Checked point
2. Uncover this plate
4. Lock this bar
Notice: Please place the CPU on the pins tenderlyto avoid bending the pins
3. Place the CPU on the top of ins
the
3. Cover this plate
15
Page 16
LV-67A User’s Manual
2.4.2 <Memory installation>
LV-67A has t wo 240-pin DDR 3 DIMM support up to 4GB of memory capacity. The memory
frequency supports 800/1066 MHz. Only Non-ECC memory is supported.
DDRIII A/B
144-pin
Please check the pin number to match the socket side well before installing memory module.
96-pin
16
Page 17
LV-67A User’s Manual
17
Page 18
LV-67A User’s Manual
2.5 <CMOS Setup>
The board’s data of CMOS can be setting in BIOS. If the board refuses to boot due to inappropriate CMOS settings, here is how to proceed to clear (reset) the CMOS to its default values.
Jumper: JRTC Type: Onboard 3-pin jumper
JRTC Mode
1-2 Clear CMOS 2-3 Normal Operation
Default setting
13
JRTC
CMOS Setup 18
Page 19
LV-67A User’s Manual
2.6 <Serial ATA installation>
LV-67A has Si x Serial ATA II interfaces with RAID function, the transfer rate of the Serial
ATA II can be up to 300MB/s. Please go to http://www.serialata.org/ ATA technology information. Based on Intel® ICH1 0DO, it supports Intel® Matrix Storage
Technology with combination of RAID 0,1,5 and 10. The main features of RAID on ICH10DO are listed below:
1. Supports for up to RAID volumes on a single, two-hard drive RAID array.
2. Supports for two, two-hard drive RAID arrays on any of six Serial ATA ports.
3. Supports for Serial ATA ATAPI devices.
4. Supports for RAID spares and automatic rebuild.
5. Supports on RAID arrays, including NCQ and native hot plug.
For more information please visit Intel’s official website.
For more about the system setup for Serial ATA, please check the chapter of SATA configuration.
for more about Serial
SATA1/2/3/4/5/6
Serial A TA installation 19
Page 20
LV-67A User’s Manual
2.7 <Floppy Installation>
LV-67A has one slim type 26-pin floppy interface, it supports notebook use floppy and
powering from onboard, please follow up the steps below to install the device.
FDD
Floppy rear side
4. Lift up this plastic bar
5. Slot the cable in (Blue paste for outside)
6. Press back the plastic bar
1. Lift up the brown plastic bar
2. Slot the cable in (Blue paste for brown bar side)
3. Press back the plastic bar
Floppy Installation 20
Page 21
LV-67A User’s Manual
2.8 <LAN installation>
The board integrates with two Intel 82574L Gigabit Ethernet controllers, as the PCI Express bus. The Intel 82574L supports triple speed of 10/100/1000Base-T, with IEEE802.3 compliance and Wake-On-LAN supported.
LAN1LAN2
LAN Installation 21
Page 22
LV-67A User’s Manual
2.9 <Onboard Display Interface>
Based on Intel Q45 chipset with built-in graphics, the board provides one DB15 Connect or on real external I/O port, or optional Secondary CRT connector (LV-67AT) and One 40-pin LVDS interface with 5-pin LCD backlight inverter connector. (LV-67AX) The board also provides 26-pin DVI interface (LV-67AD) or two DVI interface (LV-67AD2)
Notice: When you install any PCI Graphic card, the onboard graphics would be disabled automatically.
2.9.1 <Analog Display>
Please connect your CRT or LCD monitor with DB15 male connector to the onboard DB15 female connector on rear I/O port or optional Secondary CRT connector Dip 10 Pin
(L V-67AT)
CRT1
CN_CRT2
9
1
10
2
Connector: CN_CRT2 Type: onboard 10-pin connector for CRT2 (Pitch = 2.00 mm)
Pin Signal Pin Signal
2 CRT2 DDC_DA 1 CRT2 DDC_DC 4 CRT2 R 3 GND 6 CRT2 G 5 CRT2 B 8 CRT2 HSYNC 7 CRT2 VSYNC
10 GND 9 GND
22
Page 23
LV-67A User’s Manual
2.9.2 <LVDS Display LV-67AX Only >
The board provides one 40-pin LVDS connector for 18/24-bit dual channel panels, supports up to 1600 x 1200 (UXGA) of resolution, with one LCD backlight inverter connector and one jumper for panel voltage setting.
Warning : Default settings of resolution is 1024 x 768, please offer us panel’s datasheet to make OEM BIOS with customized made resolution.
39 40
1
2
CN_LVDS
CN_INV
5
JVLCD
6
5
2
1
23
Page 24
LV-67A User’s Manual
Connector: CN_INV Connector: JVLCD
Type: 5-pin LVDS Power Header Type: 6-pin Power select Header
Pin Description
1 2 3 4 5
+12V GND GND GND ENABKL
Pin Description
1-2 LCDVCC (3.3V) 3-4 LCDVCC (5V) 5-6 LCDVCC (12V)
Default setting: 1-2
Connector: CN_LVDS Type: onboard 40-pin connector for LVDS connector Connector model: HIROSE DF13-40DP-1.25V
Pin Signal Pin Signal
2 LCDVCC 1 LCDVCC 4 GND 3 GND 6 ATX0- 5 BTX0-
8 ATX0+ 7 BTX0+ 10 GND 9 GND 12 ATX1- 11 BTX1­14 ATX1+ 13 BTX1+ 16 GND 15 GND 18 ATX2- 17 BTX2­20 ATX2+ 19 BTX2+ 22 GND 21 GND 24 ACLK- 23 BTX3­26 ACLK+ 25 BTX3+ 28 GND 27 GND 30 ATX3- 29 BCLK­32 ATX3+ 31 BCLK+ 34 GND 33 GND 36 N/C 35 N/C 38 N/C 37 N/C 40 N/C 39 N/C
24
Page 25
LV-67A User’s Manual
To setup the LCD, you need the component below:
1. A panel with LVDS interfaces.
2. An inverter for panel’s backlight power.
3. A LCD cable and an inverter cable.
For the cables, please follow the pin assignm ent of the connector to make a cable, because every panel has its own pin assignment, so we do not provide a standard cable; please find a local cable manufacture to make cables.
LCD Installation Guide:
1. Preparing the LV-67AX, LCD panel and the backlight inverter.
2. Please check the datasheet of the panel to see the voltage of the panel, and set the jumper JVLCD to +5V +3.3V and 12V.
3. You would need a LVDS type cable.
Panel side
For sample illustrator only
4. To connect all of the devices well.
Board side
25
Page 26
LV-67A User’s Manual
2.9.3 <DVI Display LV-67AD and LV-67AD2>
The board provides optional DVI1-D (LV-67AD) and two DVI (LV-67AD2) interfaces with Intel Q45, compliant with DVI 1.0 standard. Connector: CN_DVI1, CN_DVI2 Connector type: 26-pin header connector (pitch = 2.00mm)
Pin Number Assignment Pin Number Assignment
1 TX1+ 2 TX1­3 Ground 4 Ground 5 TXC+ 6 TXC­7 Ground 8 PVDD
9 N/C 10 N/C 11 TX2+ 12 TX2­13 Ground 14 Ground 15 TX0+ 16 TX0­17 N/C 18 HPDET 19 DDCDATA 20 DDCCLK 21 GND 22 N/C 23 N/C 24 N/C 25 N/C 26 N/C
26
25
26
CN_DVI1
25 26
CN_DVI2
1
2
1
2
Page 27
LV-67A User’s Manual
2.10 <Audio Installation>
The board integrates onboard audio interface with REALTEK ALC888 codec, with Intel next generation of audio standard as High Definition Audio, it offers more vivid sound and oth er advantages than former HD audio compliance. The main specifications of ALC888 are:
z High-performance DACs with 100dB S/N ratio z 2 DAC channels support 16/20/24-bit PCM format for 2 audio solution z 16/20/24-bit S/PDIF-OUT supports 44.1K/48K/96kHz sample rate z Compatible with HD z Meets Microsoft WHQL/WLP 2.0 audio requirements
The board provides 2 channels audio phone jacks on rear I/O port, Line-in/MIC-in ports for front I/O panel through optional cable.
CN_AUDIO
9
10
CDIN
4
1
1
2
27
Page 28
LV-67A User’s Manual
Connector: CN_AUDIO
Type: 10-pin (2 x 5) header (pitch = 2.54mm)
Pin Description Pin Description
1 MIC_L 2 Ground 3 MIC_R 4 ACZ_DET 5 Speaker_R 6 MIC Detect 7 SENSE 8 N/C 9 Speaker_L 10 Speaker Detect
Connector: CDIN
Type: 4-pin header (pitch = 2.54mm)
Pin Description
1 CD – Left 2 Ground 3 Ground 4 CD – Right
LINE-IN LINE-OUT MIC-IN
Rear I/O phone jacks
28
Page 29
LV-67A User’s Manual
2.11 <GPIO and SMBUS interface>
The board provides a programmable 8-bit digital I/O interface, and a SMBUS (System management bus) interface for control panel application.
Connector: CN_DIO Type: onboard 2 x 6-pin header, pitch=2.0mm
Pin Description Pin Description
1 Ground 2 Ground 3 GP10 4 GP14 5 GP11 6 GP15 7 GP12 8 GP16 9 GP13 10 GP17 11 VCC 12 +12V
CN_SMBUS
5
1
Connector: CN_SMBUS Type: 5-pin header for SMBUS Ports
Pin Description
1 VCC 2 N/C 3 SMBDATA 4 SMBCLK 5 Ground
CN_DIO 12
2
11
1
29
Page 30
LV-67A User’s Manual
2.12 <USB Installation>
LV-67A integrates eight USB2.0 ports. The specifications of USB2.0 are listed below:
Interface USB2.0
Controller Intel ICH10DO
Transfer Rate Up to 480Mb/s
Voltage 5V
The Intel® ICH10DO contains two Enhanced Host Controller Interface (EHCI) and five Universal Host Controller Interfaces (UHCI), it can determine whether your connected device is for USB1.1 or USB2.0, and change the transfer rate automatically.
USB3/4/5/6
30
Page 31
LV-67A User’s Manual
Connector: CN_USB Type: 10-pin (5 x 2) header for USB5/6 Ports
Pin Description Pin Description
1 VCC 2 VCC 3 Data0- 4 Data1­5 Data0+ 6 Data1+ 7 Ground 8 Ground 9 Ground 10 N/C
CN_USB4
9
10
CN_USB1 10
1
2
9
1
2
31
Page 32
LV-67A User’s Manual
2.13 <Power and Fan Installation>
The LV-67A provides a standard ATX power supply with 24-pin ATX connector and additional 12V connector, and the board provides one 4-pin fan connectors supporting smart fan for CPU cooler and one 3-pin cooler fan connectors for system and Northbridge chip. The 4-pin CN_12V additional power connector is necessary for CPU powering; please connect this well before you finishing the system setup.
CPUFAN
4
CN_12V
4
24
23
1
3
1 2
ATX
2
1
SYSFAN
3
1
32
Page 33
LV-67A User’s Manual
Connector: ATX Type: 24-pin ATX power connector
PIN assignment
1 3.3V 13 3.3V 2 3.3V 14 -12V 3 GND 15 GND 4 5V 16 PS_ON 5 GND 17 GND 6 5V 18 GND 7 GND 19 GND 8 PW_OK 20 -5V
9 5V_SB 21 5V 10 12V 22 5V 11 12V 23 5V 12 3.3V 24 GND
Connector: CN_12V Type: 4-pin standard Pentium 4 additional +12V power connector
Pin Description Pin Description
1 Ground 2 Ground 3 +12V 4 +12V
Connector: CPUFAN Type: 4-pin fan wafer connector
Pin Description Pin Description
1 Ground 2 +12V 3 Fan Speed Detection 4 Fan Control
Connector: SYSFAN Type: 3-pin fan wafer connector
Pin Description Pin Description Pin Description
1 Ground 2 +12V 3 Sense
33
Page 34
LV-67A User’s Manual
2.14 <Serial Port>
The board supports Three RS232 serial port and one jumper selectable RS232/422/485 serial ports. The jumper JCSEL1 & JCSEL2 can let you configure the communicating modes for COM2.
Connector: COM2 Type: 9-pin D-sub male connector on bracket for COM2
Pin Description Pin Description
1 DCD/422TX-/485- 2 RXD/422TX+/485+ 3 TXD/422RX+ 4 DTR/422RX­5 GND 6 DSR 7 RTS 8 CTS 9 RI 10 N/C
COM1 COM3
COM2
34
Page 35
LV-67A User’s Manual Setting RS-232 & RS-422 & RS-485 for COM2C
JP1 JP2
1
1 5 5
2 2
6 6
JCSEL1
1
7
11
12
JCSEL2
2 8
CN_COM4
9
1
10
2
1
2
35
Page 36
LV-67A User’s Manual
Function JCSEL1 JCSEL2
SIR
RS-485
RS-422
RS-232
Default setting:
JCSEL1: (1-2) JCSEL2: (1-3, 2-4, 7-9, 8-10)
Jumper: JP1/JP2 (COM1/2) Type: onboard 6-pin header
7
1
2 8
1
7
2 8
7
1
2 8
1
7
2 8
11
12
11
12
11
12
11
12
1
2
1
2
1
2
1
2
Power Mode JP1/JP2
Pin 1 with 5V Power 1-3,4-6
Pin 9 with 12V Power 2-4,3-5
Default setting: 3-5, 4-6
1
256
1
256
36
Page 37
LV-67A User’s Manual
2.15 <Switch and Indicator>
The JFRNT provides front control panel of the board, such as power button, reset and beeper, etc. Please check well before you connecting the cables on the chassis.
Connector: JFRNT Type: onboard 14-pin (2 x 7) 2.54-pitch header
Function Signal PIN Signal Function
IDE LED
Reset
Power
Button
HDLED+ 1 2 PWDLED+
HDLED- 3 4 N/C
Reset+ 5 6 PWDLED-
Reset- 7 8 SPKIN+
N/C 9 10 N/C
PWRBT+ 11 12 N/C
PWRBT- 13 14 SPKIN-
Power
LED
Speaker
JFRNT
14
2
13
1
37
Page 38
LV-67A User’s Manual
(This Page is Left for Blank)
38
Page 39
LV-67A User’s Manual
Chapter 3 <System Configuration>
3.1 <SATA configuration>
SA TA Mode:
This option can let you select whether the Serial ATA hard drives would work under normal IDE mode or RAID mode. The RAID mode need more than one HDD is applied.
39
Page 40
LV-67A User’s Manual
3.2 <SATA RAID Configuration>
The board integrates Intel® ICH10DO with RAID function for Serial ATA II drives, and supports the configurations below: RAID 0 (Stripping): Two hard drives operating as one drive for optimized data R/W performance. It needs two unused drives to build this operation. RAID 1 (Mirroring): Copies the data from first drive to second drive for data security, and if one drive fails, the system would access the applications to the workable drive. It needs two unused drives or one used and one unused driv e to build this operation. The second drive must be the same or lager size than first one.
RAID 5 (striping with parity)
A RAID 5 array contains three or more hard drives where the data is divided into manageable blocks called strips. Parity is a mathematical method for recreating data that was lost from a single drive, which increases fault-tolerance. The data and parity are striped across all the hard drives in the array. The parity is striped in a rotating sequence to reduce bottlenecks associated with the parity calculations.
RAID 10 (RAID 0+1)
A RAID 10 array uses four hard drives to create a combination of RAID levels 0 and 1. The data is striped across a two-drive array forming the RAID 0 component. Each of the drives in the RAID 0 array is then mirrored by a RAID 1 component. Intel Matrix Storage Technology: This technology would allow you to use RAID 0+1 mode on only two drives (4 drives needed on traditional RAID 0+1). It will create two partitions on each hard drive to simulate RAID 0 and RAID 1. It also can let you modify the partition size without re-formatted.
For more information of Intel Matrix Storage Technology, please visit Intel’s website.
If you need to install an operation system on the RAID set, please use the driver disk attached in the package when it informs you to obtain the RAID drivers.
40
Page 41
LV-67A User’s Manual
Please press <CTRL+I> to enter the RAID configuration menu. You can setup the RAID under operation system for Microsoft® Windows XP SP1 or Windows 2000 SP4 version, please install the Intel® Application Accelerator Ver.4.5 later to support RAID configuration with Intel® Matrix Storage Technology.
41
Page 42
LV-67A User’s Manual
1. After installing Intel Application Accelerator, please execute Intel® Storage Utility.
Demo configuration for 2 SATA Drives and set as Intel Matrix Storage Technology set
2. Select Actions to Create RAID Volume
Rename the Volume name
Select RAID Level as 0
Left as default
42
Page 43
LV-67A User’s Manual
3. Please select two hard drives to prepare to set the RAID volume
4. Specify the Volume size
Tune this bar to specify the volume size, if you specify the volume size lower than maximum, you can create a second volume for another RAID set. (Make RAID 0+1 on only two hard drives)
5. Repeat the step 1 to create second volume as RAID Level 1.
For other configuration set please click Help on tool bar.
43
Page 44
LV-67A User’s Manual
3.3 <Audio Configuration>
The board integrates Intel® ICH10DO with REALTEK® ALC888 codec. It can support 2-channel sound under system configuration. Please follow the steps below to setup your sound system.
1. Install REALTEK HD Audio driver.
2. Lunch the control panel and Sound Effect Manager.
3. Select Speaker Configuration
4. Select the sound mode to meet your speaker system.
44
Page 45
LV-67A User’s Manual
3.4 <Video Memory Setup>
Based on Intel® Q45 chipset with GMA (Graphic Media Accelerator) 4500, the board supports Intel® DVMT (Dynamic Video Memory Technology) 3.0, which would allow the video memory be triggered up to 384MB. To support DVMT, you need to install the Intel GMA4500 Driver with supported OS.
BIOS Setup: On-Chip Frame Buffer Size:
This item can let you select video memory which been allocated for legacy VGA and SVGA graphics support and compatibility. The available option is 32MB and 128MB.
45
Page 46
LV-67A User’s Manual Total GFX Memory Size:
This item can let you select a static amount of page-locked graphics memory; which will be allocated during driver initialization. Once you select the memory amount, it will be no longer available for system memory.
DVMT Memory Size:
This item can let you select a maximum size of dynamic amount usage of video memory, the system would configure the video memory depends on your appl ication, this item is strongly recommend to be selected as MAX DVMT.
Fixed + DVMT Memory Size:
You can select the fixed amount and the DVMT amount at the same time for a guarantee d video memory and additional dynamic video memory Notice:
1. The On-Chip Frame Buffer Size would be included in the Total GFX Memory Size.
46
Page 47
LV-67A User’s Manual
3.5 <Display Properties Setting>
Based on Intel Q45 GMCH with GMA3000 (Graphic Media Accelerator), the board supports two DACs for display device as different resolution and color bit. Please install the Intel Graphic Driver before you starting setup display devices.
1. Click right button on the desktop to lunch display properties
2. Click Advanced button for more specificity setup.
3. This setup options can let you define each device settings.
47
Click Graphics Properties... for advanced setup
Page 48
LV-67A User’s Manual
Click Monitor to setup the CRT monitor for Colors, Resolution and Refresh Rate
Click Intel® Dual Display
Clone to setup the dual
display mode as same screen
Set the main display device here
Click Extended Desktop to setup the dual display mode as different screen display
48
Page 49
LV-676 User’s Manual
Chapter 4 <BIOS Setup>
The motherboard uses the Award BIOS for the system configuration. The Award BIOS in the single board computer is a customized version of the industrial standard BIOS for IBM PC AT-compatible computers. It supports Intel x86 and compatible CPU architecture based processors and computers. The BIOS provides critical low-level support for the system central processing, memory and I/O sub-systems.
The BIOS setup program of the single board computer let the customers modify the basic configuration setting. The settings are stored in a dedicated battery-backed memory, NVRAM, retains the information when the power is turned off. If the battery runs out of the power, then the settings of BIOS will come back to the default setting.
The BIOS section of the manual is subject to change without notice and is provided here for reference purpose only. The settings and configurations of the BIOS are current at the time of print, and therefore they may not be exactly the same as that displayed on your screen.
To activate CMOS Setup program, press <DEL> key i mmediately after you turn on the system. The following message “Press DEL to enter SETUP” should appear in the lower left hand corner of your screen. When you enter the CMOS Setup Utility, the Main Menu will be displayed as Figure 4-1. You can use arrow keys to select your function, press Enter key to accept the selection and enter the sub-menu.
Figure 4-1 CMOS Setup Utility Main Screen
49
Page 50
LV-674 User’s Manual
(This Page is Left for Blank)
50
Page 51
LV-67A User’s Manual
Appendix A <I/O Port Pin Assignment>
A.1 <Serial ATA Port>
Connector: S_ATA1/2/3/4/5/6 Type: 7-pin wafer connector
1 2 3 4 5 6 7
GND RSATA_TXP1 RSATA_TXN1 GND RSATA_RXN1 RSATA_RXP1 GND
17
A.2<Floppy Port>
Connector: FDD Type: 26-pin connector
Pin Description Pin Description
1 VCC 2 INDEX 3 VCC 4 DRV0 5 VCC 6 DSKCHG 7 DRV1 8 N/C 9 MTR1 10 MTR0 11 RPM 12 DIR 13 N/C 14 STEP 15 Ground 16 WRITE DATA 17 Ground 18 WRITE GATE 19 N/C 20 TRACK 0 21 N/C 22 WRPTR 23 Ground 24 RDATA­25 Ground 26 SEL
51
Page 52
LV-67A User’s Manual
A.3 <IrDA Port>
Connector: CN_IR Type: 5-pin header for SIR Ports
Pin Description
1 VCC 2 N/C 3 IRRX 4 Ground 5 IRTX
1
5
A.4 <Serial Port>
Connector: COM1/2/3 Type: 9-pin D-sub male connector on bracket
Pin Description Pin Description
1 DCD 6 DSR 2 SIN 7 RTS 3 SO 8 CTS 4 DTR 9 RI 5 Ground
Connector: COM4 Type: 9-pin header connector for COM4
Pin Description Pin Description
1 DCD 6 DSR 2 SIN 7 RTS 3 SO 8 CTS 4 DTR 9 RI 5 Ground
1 2 3 4 5
10
6 7 8 9
9
1
2
52
Page 53
LV-67A User’s Manual
A.5 <VGA Port>
Connector: CRT1 Type: 15-pin D-sub female connector on bracket
Pin Description Pin Description Pin Description
1 RED 6 Ground 11 N/C 2 GREEN 7 Ground 12 DDC_DA 3 BLUE 8 Ground 13 HSYNC 4 N/C 9 +5V 14 VSYNC 5 Ground 10 Ground 15 DDC_CLK
6
1 2 3 4 5
10
11 12 13 14 15
A.6 <LAN Port>
Connector: RJ451/2 Type: RJ45 connector with LED on bracket
Pin 1 2 3 4 5
Description TRD0+ TRD0- TRD1+ TRD2+ TRD2-
Pin 6 7 8 9 10
Description TRD1- TRD3+ TRD3- NC NC
53
Page 54
LV-67A User’s Manual
Appedix B <System Resources>
B.1 <I/O Port Address Map>
54
Page 55
LV-67A User’s Manual
55
Page 56
LV-67A User’s Manual
B.2 <Memory Address Map>
56
Page 57
LV-67A User’s Manual
B.3 <System IRQ Resources>
57
Page 58
LV-67A User’s Manual
Appedix C <Flash BIOS>
C.1 <BIOS Auto Flash Tool>
The board is based on Award BIOS and can be updated easily by the BIOS auto flash tool. You can download the tool online at the address below:
TUhttp://www.award.comUT TUhttp://www.commell.com.tw/support/support.htmUT
File name of the tool is “awdflash.exe”, it’s the utility that can write the data into the BIOS flash ship and update the BIOS.
C.2 <Flash Method>
1. Please make a bootable floppy disk.
2. Get the last .bin files you want to update and copy it into the disk.
3. Copy awardflash.exe to the disk.
4. Power on the system and flash the BIOS. (Example: C:/ awardflash XXX.bin)
5. Re-star the system.
Any question about the BIOS re-flash please contact your distributors or visit the web-site at below:
http://www.commell.com.tw/support/support.htm
58
Page 59
LV-67A User’s Manual
Appendix D <Programming GPIO’s>
The GPIO’can be programmed with the MSDOS debug program using simple IN/OUT commands.The following lines show an example how to do this.
GPIO0…..GPIO7 bit0……bit7
-o 2E 87 ;enter configuration
-o 2E 87
-o 2E 07
-o 2F 09 ;enale GPIO function
-o 2E 30
-o 2F 02 ;enable GPIO configuration
-o 2E F0
-o 2F xx ;set GPIO as input/output; set ‘1’ for input,’0’for output
-o 2E F1
-o 2F xx ;if set GPIO’s as output,in this register its value can be set
Optional :
-o 2E F2
-o 2F xx ; Data inversion register ; ‘1’ inverts the current valus of the bits ,’0’ leaves them as they are
-o 2E 30
-o 2F 01 ; active GPIO’s
For further information ,please refer to Winbond W83627DHG datasheet.
59
Page 60
LV-67A User’s Manual
Appendix E <Watch Dog timer Setting >
The watchdog timer makes the system auto-reset while it stops to work for a period. The integrated watchdog timer can be setup as system reset mode by program.
Timeout Value Range
- 1 to 255
- Second or Minute
Program Sample
Watchdog timer setup as system reset with 5 second of timeout
2E, 87 2E, 87 2E, 07 2F, 08 Logical Device 8 2E, 30 Activate 2F, 01 2E, F5 Set as Second* 2F, 00 2E, F6 Set as 5 2F, 05
* Minute: bit 3 = 0; Second: bit 3 = 1
You can select Timer setting in the BIOS, after setting the time options, the system will reset according to the period of your selection.
60
Page 61
LV-67A User’s Manual
Contact Information
Any advice or comment about our products and service, or anything we can help you please don’t hesitate to contact with us. We will do our best to support you for your products, projects and business.
Taiwan Commate Computer Inc.
Address
TEL +886-2-26963909 FAX +886-2-26963911 Website E-Mail
Facebook
Twitter https://twitter.com/Taiwan_Commate
19F, No. 94, Sec. 1, Xintai 5th 22102, Taiwan
TUhttp://www.commell.com.twUT TUinfo@commell.com.twUT (General Information)
TUtech@commell.com.twUT (Technical Support)
https://www.facebook.com/pages/Taiwan-Commate-Computer-Inc/547993955271899
Rd., Xizhi Dist., New Taipei City
Commell is a brand name of Taiwan commate computer Inc.
Contact Information
61
Loading...