COMMELL LS-570E User Manual

Page 1
LS-570
5.25 inch Embedded Miniboard
User’s Manual
Edition 1.3
2011/03/10
Page 2
LS-570 User’s Manual
Copyright
Copyright 2006. All rights reserved. This document is copyrighted and all rights are reserved. The information in this document is subject to change without prior notice to make improvements to the products. This document contains proprietary information and protect ed by copyright. No part of this document may be reproduced, copied, or translated in any form or any means without prior written permission of the manufacturer. All trademarks and/or registered trademarks contains in this document are propert y of their respective owners.
Disclaimer
The company shall not be liable for any incidental or consequenti al dam ages res ultin g from the performance or use of this product. The company does not issue a warranty of any kind, e xpress or implied, including without limitation implied warranties of merchantability or fitness for a particular purpose. The company has the right to revise the manual or include changes in th e specifications of the product described within it at any time without notice and without obligation to notify any person of such revision or changes.
Trademark
All trademarks are the property of their respective holders.
Any questions please visit our website at TUhttp://www.commell.com.twUT
2
Page 3
LS-570 User’s Manual
Packing List
Please check the package before you starting setup the system
Hardware:
LS-570 series motherboard x 1
Cable Kit:
44-pin
44-pin
ATA33 IDE Cable x1
Power Cable x 1
COM & Printer Port Cable x 1
40-pin
COM Port Cable x 1
PS2 Cable x 1
SATA Cable x 2
26-pin Slim Type Floppy Cable x 1
DVI module with bracket x 1
SDTV Cable x 1
YPbPr Cable x 1
Audio Port Cable x 1
3
Page 4
LS-570 User’s Manual
Printed Matters:
Driver CD x 1 (Including User’s Manual)
USB Cable x 1 CPU Cooler x 1
4
Page 5
LS-570 User’s Manual
Index
Chapter 1 <Introduction>.....................................................................................8
1.1 <Product Overview>.................................................................................8
1.2 <Product Specification>...........................................................................9
1.3 <Mechanical Drawing>...........................................................................11
1.4 <Block Diagram>....................................................................................12
Chapter 2 <Hardware Setup>.............................................................................13
2.1 <Connector Location>............................................................................13
2.2 <Jumper Reference> .............................................................................15
2.3 <Connector Reference>.........................................................................16
2.3.1 <Internal Connector>..................................................................16
2.3.2 <External Connector>.................................................................16
2.4 <CPU and Memory Setup>.................................................................... 17
2.4.1< CPU>........................................................................................17
2.4.2 <Memory> ..................................................................................18
2.5 <CMOS ATX Setup>..............................................................................19
2.6 <Enhanced IDE & CF Interface>............................................................20
2.7 <Serial ATA Interface>...........................................................................21
2.8 <Floppy Port>......................................................................................... 22
2.9 <LAN Interface>.....................................................................................23
2.10.1 <Analog VGA Interface> ..........................................................23
2.10.2 <Digital Display>.......................................................................24
2.10.3 <DVI Interface > .......................................................................27
2.10.4<TV-out Interface>.....................................................................28
2.11 <Onboard Audio Interface>..................................................................31
2.12 <USB2.0 Interface>..............................................................................32
2.13 <GPIO Interface>.................................................................................34
2.14 <Serial Port Jumper Setting >..............................................................35
2.15.1 <Power Input>..........................................................................37
5
Page 6
LS-570 User’s Manual
2.15.2 <Power Output> .......................................................................38
2.15.3 <Fan Connector>....................................................................38
2.16 <Indicator and Switch>.........................................................................39
Chapter 3 <System Configuration>...................................................................41
3.1 <Video Memory Setup> .........................................................................41
Chapter 4 <BIOS Setup> .................................................................................... 45
Appendix A <I/O Port Pin Assignment> ...........................................................47
A.1 <IDE Port>.............................................................................................47
A.2 <Floppy Port> ........................................................................................48
A.3 <IrDA Port>............................................................................................48
A.4 < CRT Port >..........................................................................................49
A.5 <Serial ATA Port>..................................................................................49
A.6 <Serial Port>..........................................................................................49
A.7 <LAN Port>............................................................................................50
A.8 <Parallel Port>.......................................................................................50
Appendix B <Flash BIOS>..................................................................................51
B.1 BIOS Auto Flash Tool .....................................................................51
B.2 Flash Method...................................................................................51
Appendix C <System Resources> .................................................................... 52
Appendix D <Watch Dog timer Setting >..........................................................56
Contact Information............................................................................................58
6
Page 7
LS-570 User’s Manual
(The Page is Left For Blank)
7
Page 8
LS-570 User’s Manual Introduction
Chapter 1 <Introduction>
1.1 <Product Overview>
LS-570 is the 5.25 inc h Embedded miniboard, with supporting Intel Core Duo/Core Solo
processors for 533/667MHz front side bus, Intel 945GM(E) and ICH7-M chipset, integrated GMA950 graphics, DDR2 memory, Realtek AC97 Audio, Serial ATA and four Intel 82537L Gigabit LAN .
Intel Yonah dual core Processor
The board supports Intel Core Duo/Core Solo processors with 533/667MHz front side bus, 2MB L2 cache, to provide more powerful performance than before.
New features for Intel 945GM(E) chipset
The board integrates Intel 945GM(E) and ICH7-M chipset, to provide new generation of the mobile solution, supports Intel GMA950 graphics, DDR2 533/667 memory, built-in high speed mass storage interface of serial ATA, AC97 Audio with 5.1 channels surrounding sound.
All in One multimedia solution
Based on Intel 945GM(E) and ICH7-M chipset, the board provides high performance onboard graphics, 18-bit Dual channel LVDS interface, DVI and HDTV and 5.1 channels AC97 Audio, to meet the very requirement of the multimedia application.
Flexible Extension Interface
The board also provides CompactFlash Type II socket and one mini-PCI socket.
8
Product Overview
Page 9
LS-570 User’s Manual Introduction
1.2 <Product Specification>
General Specification
Form Factor 5.25 inch miniboard CPU Intel® Core Duo/Core Solo processor
Package type: Micro- FCPGA478 Front side bus: 533/667MHz
Memory 2 x 240-pin DDR2 533/667MHz SDRAM up to 3GB
Up to 10.67GB/s of bandwidth with dual-channel interleaved mode Dual-Channel technology supported Unbufferred, none-ECC memory supported only
Chipset Intel® 945GM(E) and ICH7-M BIOS Phoenix-Award v6.00PG 4Mb PnP flash BIOS Green Function Power saving mode includes doze, standby and suspend modes.
ACPI version 1.0 and APM version 1.2 compliant
Watchdog Timer System reset programmable watchdog timer with 1 ~ 255
sec./min. of timeout value Real Time Clock Intel® ICH7-M built-in RTC with lithium battery Enhanced IDE UltraDMA33 IDE interface supports up to 2 ATAPI devices
One 44-pin IDE port onboard
One CompactFlash Type II socket on solder side Serial ATA Intel® ICH7-M integrates 2 Serial ATA interfaces
(No RAID Function)
Up to 150MB/s of transfer rate
Multi-I/O Port
Chipset Intel® ICH7-M with Winbond® W83627THG controller Serial Port Three RS-232 and one RS-232/422/485 serial ports USB Port Two external & Four internal Hi-Speed USB 2.0 ports with
480Mbps of transfer rate Parallel Port One 26-pin internal parallel port Floppy Port One slim type Floppy port IrDA Port One IrDA compliant Infrared interface supports SIR K/B & Mouse PS/2 keyboard and mouse port GPIO One 12-pin Digital I/O connector with 8-bit programmable I/O
interface
Smart Fan One CPU fan connectors for fan speed controllable
VGA Display Interface
Chipset Intel® 945GM(E) GMCH (Graphic Memory Controller Hub) Frame Buffer Up to 224MB shared with system memory Display Type CRT, LCD monitor with analog display Connector External DB15 female connector on rear I/O panel
Onboard 40-Pin LVDS connector
Product Specification
9
Page 10
LS-570 User’s Manual Introduction
Onboard 26-Pin DVI connector Onboard 10-Pin TV-out connector
Ethernet Interface
Controller 4 x Intel 82573L Gigabit Ethernet controller Type Triple speed 10/100/1000Base-T
auto-switching Fast Ethernet Full duplex, IEEE802.3U compliant
Connector Four External RJ45 connector with LED on rear I/O panel
Audio Interface
Chipset REALTEK ALC655 Interface 5.1 channel surround audio with Line-in, Line-out and MIC-in
Connector Onboard audio connector with pin header
Onboard CD-IN connector
Expansive Interface
PCI 1 x PCI slot supports up to two PCI devices through riser card Mini PCI 1 x Mini PCI socket
Power and Environment
Power Requirement Standard 24-pin ATX power supply (20-pin is compatible)
DC 8~24V input with external DC Jack or onboard 4-pin
connector Dimension 146 (L) x 203 (H) mm Temperature Operating within 0 ~ 60 (32 ~ 140℉)
Storage within -20 ~ 85 (-4 ~ 185℉)
Ordering Code
LS-570 Support Intel Core Duo/Solo processor with onboard VGA, HDTV
, DVI, LVDS, Audio, SATA, Giga LAN, USB2.0, LPT, CF, GPIO, Mini PCI, FDD
The specifications may be different as the actual production. For further product information please visit the website at
TUhttp://www.commell.com.twUT
10
Product Specification
Page 11
LS-570 User’s Manual Introduction
1.3 <Mechanical Drawing>
Mechanical Drawing
11
Page 12
LS-570 User’s Manual Introduction
r
1.4 <Block Diagram>
Intel Yonah Processo
2 x 240-pin DDR2
Intel GMA950 Graphics
533/677MHz up to 3GB
HDTVLVDSDVI
CompactFlashIDE
6 x USB2.0 ports
1 x LPT port
1 x Floppy port
2 x Serial ports
W83627THG
1 x PCI
945GM(E)
ICH7-M
2 x SATA
AC97 ALC655
Intel 82537L
4 x GLAN
Fintek
F81216D
2 x Serial port
8-bit GPIO
BIOS
Block Diagram
12
Page 13
LS-570 User’s Manual Hardware Setup
_
Chapter 2 <Hardware Setup>
2.1 <Connector Location>
SATA1/2
JAT
MINIPCI
PCI
CN_IR
DIO
CN
CN_LPT
CN_PS2
SYSFAN
IDE
FDD
DDRII_A/B
CN_LVDS
CN_INV
ATX
CPUFAN
DC_OUT
JFRNT
CD_IN
CN_COM2/3/4
Connector Location
CN_HDTV
CN_USB1/2
CN_DVI
CN_AUDIO
13
Page 14
LS-570 User’s Manual Hardware Setup
14
COM1
CF
LAN1/2/3/4
USB CRT DC_IN
Connector Location
Page 15
LS-570 User’s Manual Hardware Setup
2.2 <Jumper Reference>
Jumper Function
JRTC CMOS Operating/Clear Setting JCFSEL Compact Flash address mode setting JVLCD LCD Panel Voltage Setting JCRT CRT attach select setting JAT Power mode select JCSEL1/2 COM2 RS232/422/485 mode setting
Jumper: JAT Type: onboard 2-pin header
Power Mode JAT
JRTC
JAT
JCFSEL
AT Mode
ATX Mode
Default setting: ATX Mode
JVLCD
JCRT
JCSEL1
Jumper Reference
JCSEL2
15
Page 16
LS-570 User’s Manual Hardware Setup
2.3 <Connector Reference>
2.3.1 <Internal Connector>
Connector Function Remark
DDRIIA/B 240 -pin DDR2 SDRAM DIMM slot Standard IDE 44-pin primary IDE connector Slim FDD 26-pin slim type floppy connector Slim SATA1/2 7-pin Serial ATA connector Standard CN_12V 4-pin power supply connector Standard ATX 24-pin power supply connector Standard CN_AUDIO 5 x 2-pin audio connector Standard CDIN 4-pin CD-ROM audio input connector Standard CN_DIO 6 x 2-pin digital I/O connector Standard CN_USB1/2 5 x 2- pin USB connector Standard CPUFAN 4-pin CPU cooler fan connector Standard SYSFAN 3-pin system cooler fan connector Standard CN_COM2/3/4 5 x 2-pin com connector Standard CN_IR 5-pin IrDA connector Standard CF Compact Flash Type II socket Standard CN_LVDS 20 x 2-pin LVDS connector Standard CN_HDTV 5 x 2-pin HDTV interface Standard CN_INV 5-pin LCD inverter connector Standard DC_OUT 4-pin power output connector Standard PCI 32bit PCI slot Slim MINIPCI Mini-PCI socket Standard CN_LPT 13 x 2-pin printer connector Standard CN_PS2 5 x 2-pin PS2 connector Standard CN_DVI 13 x 2-pin DVI interface Standard JFRNT 14-pin switch/indicator connector Standard
2.3.2 <External Connector>
Connector Function Remark
CRT DB15 VGA connector Standard USB Dual USB 2.0 connector Standard COM1 DB9 Serial port connector Standard RJ45_1/2/3/4 Four RJ45 LAN connector Standard DC_IN DC 8~24V input jack Standard
16
Connector Reference
Page 17
LS-570 User’s Manual Hardware Setup
y
2.4 <CPU and Memory Setup>
2.4.1< CPU>
The board comes with the socket479 for Intel Core Duo/Core Solo processor , it supports new generation of Intel Core Duo processor with 533/667MHz of front side bus and 2MB L2 cache. Please follow the instruction to install the CPU properly.
Unlock wa
1. Use the flat-type screw drive to unlock the CPU socket
2. Follow the pin direction to install the processor on the socket
Check point
3. Lock the socket
CPU and Memory Setup
17
Page 18
LS-570 User’s Manual Hardware Setup
2.4.2 <Memory>
T The board provides two 240-pin DDR2 DIMMs to support DDR2 533/667 memory modules up to 3GB of capacity. Non-ECC, unbuffered memory is supported onl y. While applying two same modules, dual channel technology is enabled automatically for higher performance.
DDRIIA/B
18
112-pin128-pin
Please check the pin number to match the slot side well before installing memory module.
Memory Setup
Page 19
LS-570 User’s Manual Hardware Setup
2.5 <CMOS ATX Setup>
The board’s data of CMOS can be setting in BIOS. If the board refuses to boot due to inappropriate CMOS settings, here is how to proceed to clear (reset) the CMOS to its default values.
Jumper: JRTC Type: Onboard 3-pin jumper
JRTC Mode
1-2 Clear CMOS 2-3 Normal Operation
Default setting
1
3
JRTC
CMOS A TX Setup
19
Page 20
LS-570 User’s Manual Hardware Setup
2.6 <Enhanced IDE & CF Interface>
The board has one Ultra DMA33 IDE interface to support up to 2 ATAPI devices, and one Compact Flash Type II socket on the solder side. The board also provides a Compact Flash Type II socket with jumper (JCFSEL) selectable slave/Master mode on secondary IDE channel.
Jumper: JCFSEL Type: onboard 3-pin header
JCFSEL Mode
1-2 Master 2-3 Slave
Default setting:2-3
JCFSEL
43
44
1
3
IDE
1
2
20
Enhanced IDE&CF Interface
Page 21
LS-570 User’s Manual Hardware Setup
2.7 <Serial ATA Interface>
Based on Intel ICH7-M, the board provides two Serial ATA interfaces with up to 150MB/s of transfer rate
.
SATA1/2
Serial A TA Interface
21
Page 22
LS-570 User’s Manual Hardware Setup
2.8 <Floppy Port>
The board provides a slim type floppy port; please use the 26-pin ribbon cable in the package to connect the floppy device.
FDD
22
Floppy rear side
4. Lift up this plastic bar
5. Slot the cable in (Blue paste for outside)
6. Press back the plastic bar
1. Lift up the brown plastic bar
2. Slot the cable in (Blue paste for brown bar side)
3. Press back the plastic bar
Floppy Port
Page 23
LS-570 User’s Manual Hardware Setup
2.9 <LAN Interface>
The Intel 82573L supports triple speed of 10/100/1000Base-T, with IEEE802.3 compliance and Wake-On-LAN supported.
LAN_1/2/3/4
2.10 <Onboard Display Interface>
Based on Intel 945GM(E) chipset with built-in GMA (Graphic Media Accelerator) 950 graphics, the board provides one DB15 connector on real external I/O port, and one 40-pin LVDS interface with 5-pin LCD backlight inverter connector. The board provides dual display function with clone mode and extended desktop mode for CRT and LCD and DVI and TV-out.
2.10.1 <Analog VGA Interface>
Please connect your CRT or LCD monitor with DB15 male connector to the onboard DB15 female connector on rear I/O port.
CRT
LAN Interface
23
Page 24
LS-570 User’s Manual Hardware Setup
2.10.2 <Digital Display>
The board provides one 40-pin LVDS connector for 18/24-bit single/dual channel panels, supports up to 1600 x 1200 (UXGA) of resolution, with one LCD backlight inverter connector and one jumper for panel voltage setting
5
1
24
CN_INV
40
39
CN_LVDS
JVLCD
3
1
2
1
Digital Display
Page 25
LS-570 User’s Manual Hardware Setup
Connector: CN_INV Connector: JVLCD Type: 5-pin LVDS Power Header Type: 3-pin Power select Header Connector model: JST B5B-XH-A
Pin Description Pin Description
1 +12V 1 VCC(5V) 2 GND 2 LCDVCC 3 GND 3 VCC3(3.3) 4 GND 5 ENABKL
Connector: CN_LVDS Type: onboard 40-pin connector for LVDS connector Connector model: HIROSE DF13-40DP-1.25V
Pin Signal Pin Signal
2 LCDVCC 1 LCDVCC 4 GND 3 GND 6 ATX0- 5 BTX0-
8 ATX0+ 7 BTX0+ 10 GND 9 GND 12 ATX1- 11 BTX1­14 ATX1+ 13 BTX1+ 16 GND 15 GND 18 ATX2- 17 BTX2­20 ATX2+ 19 BTX2+ 22 GND 21 GND 24 ACLK- 23 BTX3­26 ACLK+ 25 BTX3+ 28 GND 27 GND 30 ATX3- 29 BCLK­32 ATX3+ 31 BCLK+ 34 GND 33 GND 36 N/C 35 N/C 38 N/C 37 N/C 40 N/C 39 N/C
Digital Display
25
Page 26
LS-570 User’s Manual Hardware Setup
To setup the LCD, you need the component below:
1. A panel with LVDS interfaces.
2. An inverter for panel’s backlight power.
3. A LCD cable and an inverter cable.
For the cables, please follow the pin assignm ent of the connector to make a cable, because every panel has its own pin assignment, so we do not provide a standard cable; please find a local cable manufacture to make cables.
LCD Installation Guide:
1. Preparing the LS-570, LCD panel and the backlight inverter.
2. Please check the datasheet of the panel to see the voltage of the panel, and set the jumper JVLCD to +5V or +3.3V.
3. You would need a LVDS type cable.
Panel side
For sample illustrator only
4. To connect all of the devices well.
26
Board side
Digital Display
Page 27
LS-570 User’s Manual Hardware Setup
2.10.3 <DVI Interface >
The board also comes with a DVI interface with Chrontel CH7307C for digital video interface.
Connector: CN_DVI Connector type: 26-pin header connector (pitch = 2.00mm)
Pin Number Assignment Pin Number Assignment
1 TX1+ 2 TX1­3 Ground 4 Ground 5 TXC+ 6 TXC­7 Ground 8 PVDD 9 N/C 10 N/C
11 TX2+ 12 TX2­13 Ground 14 Ground 15 TX0+ 16 TX0­17 N/C 18 HPDET 19 DDCDATA 20 DDCCLK 21 GND 22 N/C 23 N/C 24 N/C 25 N/C 26 N/C
DVI Interface
26
CN_DVI
1
27
Page 28
LS-570 User’s Manual Hardware Setup
2.10.4<TV-out Interface>
The board provides an HDTV interface with Intel 945GM(E), supports PAL and NTSC of TV system, and display (clone or extended desktop) function with CRT,LV DS,DVI.
Connector: CN_HDTV Connector type: 10-pin header HDTV connector (pitch = 2.54mm)
Pin Number Assignment Pin Number Assignment
1 GND 2 DACB 3 DACC 4 N/C 5 GND 6 GND 7 DACA 8 N/C 9 N/C 10 N/C
28
10
CN_HDTV
1
TV-out Interface
Page 29
LS-570 User’s Manual Hardware Setup
(
To connect the TV set, please follow the diagram below to setup your system:
YPrPb Component Cable
For HDTV)
TV-out Interface
29
Page 30
LS-570 User’s Manual Hardware Setup
After setup the devices well, you need to select the LCD panel type in the BIOS.
The panel type mapping is list below:
BIOS panel type selection form
18 bits Single channel 24 bits Dual channel
NO. Output format NO. Output format
1 640 x 480 9 1024 x 768 2 800 x 600 10 1280 x 768 3 1024 x 768 11 1280 x 1024
24 bits Single channel 12 1366 x 7 68 4 1280 x 768 13 1400 x 1050 @ 108Mhz 5 1280 x 1024 15 1600 x 1200 6 1366 x 768 7 1280 x 800 8 1600 x 1200
14 1024 x 768
30
TV-out Interface
Page 31
LS-570 User’s Manual Hardware Setup
2.11 <Onboard Audio Interface>
The board provides the onboard AC97 5.1-channel audio int erface with Realteck ALC655.
Connector: CN_AUDIO
Type: 10-pin (2 x 5) header (pitch = 2.54mm)
Pin Description Pin Description
1 Line/SURR – Left 2 Ground 3 Line/SURR Right 4 MIC1/CEN 5 MIC2/LEF 6 Ground 7 N/C 8 Line Out– Left 9 Line Out – Right 10 Ground
Connector: CDIN
Type: 4-pin header (pitch = 2.54mm)
Pin Description
1 CD – Left 2 Ground 3 Ground 4 CD – Right
Onboard Audio Interface
4 1
CDIN
CN_AUDIO
1
10
31
Page 32
LS-570 User’s Manual Hardware Setup
2.12 <USB2.0 Interface>
Based on Intel ICH7-M , the board provides 4USB2.0 ports. The USB2.0 interface provides up to 480Mbps of transferring rate.
Interface USB2.0
Controller ICH7-M
Transfer Rate Up to 480Mb/s
Output Intensity 500mA
32
CN_USB
1
10
USB
USB2.0 Interface
Page 33
LS-570 User’s Manual Hardware Setup
Connector: CN_USB Type: 10-pin (5 x 2) header for USB1/2 Ports
Pin Description Pin Description
1 VCC 2 VCC 3 Data0- 4 Data1­5 Data0+ 6 Data1+ 7 Ground 8 Ground 9 Ground 10 N/C
PS: The USB2.0 will be only active when you connecting with the USB2.0 devices, if you insert an USB1.1 device, the port will be changed to USB1.1 protocol automatic ally. The transferring rate of USB2.0 as 480Mbps is depending on device capacity, exact transferring rate may not be up to 480Mbps.
USB2.0 Interface
33
Page 34
LS-570 User’s Manual Hardware Setup
2.13 <GPIO Interface>
The board provides a programmable 8-bit digital I/O interface; you can use this general purpose I/O port for system control like POS or KIOSK.
Connector: CN_DIO Type: onboard 2 x 6-pin header, pitch=2.0mm
Pin Description Pin Description
1 Ground 2 Ground 3 GP0 4 GP4 5 GP1 6 GP5 7 GP2 8 GP6 9 GP3 10 GP7 11 VCC 12 +12V
34
CN_DIO
12
1
GPIO Interface
Page 35
LS-570 User’s Manual Hardware Setup
2.14 <Serial Port Jumper Setting >
The board provides three RS232 serial ports, with jumper selectable RS422/485 for COM2.
Connector: CN_COM2/3/4 Type: 10-pin (5 x 2) header for COM2/3/4
Pin Description Pin Description
1 DCD/422TX-/485- 2 RXD/422TX+/485+ 3 TXD/422RX+ 4 DTR/422RX­5 GND 6 DSR 7 RTS 8 CTS 9 RI 10 N/C
10
JCSEL1 JCSEL2
RS-232
RS-485
RS-422
Serial Port Jumper Setting
6 2
51
12
11
12
35
Page 36
LS-570 User’s Manual Hardware Setup
CN_COM2/3/4
JCSEL1
JCSEL2
10
COM
36
Serial Port Jumper Setting
Page 37
LS-570 User’s Manual Hardware Setup
2.15 <Power and Fan Connector>
The board requires DC input with 2-pin DC-Jack power connector on rear I/O panel, or onboard 4-pin ATX2.0 12V connector, the input voltage range is from 8V to 24V, for the input current, please take a reference of the power consumption report on appendix.
2.15.1 <Power Input>
Connector:CN_DCIN Type: 4-pin DC power connector
Pin Description Pin Description
1 +12V 2 +12V 3 Ground 4 Ground
13
SYSFAN
14
CPUFAN
DC_OUT
4
1
1
3
4
2
CN_DCIN
Power and Fan Connector
DC_IN
37
Page 38
LS-570 User’s Manual Hardware Setup
2.15.2 <Power Output>
Connector: DC_OUT Type: 4-pin P-type connector for +5V/+12V
Pin Description Pin Description Pin Description Pin Description
1 +5V 2 Ground 3 Ground 4 +12V
Note: Maximum output voltage: 12V/5A & 5V/3A
Floppy
ATAPI Drives
Relative Accessory
2.15.3 <Fan Connector>
Connector: SYSFAN Type: 3-pin fan wafer connector
Pin Description Pin Description Pin Description
1 Ground 2 +12V 3 Fan Speed detect
Connector: CPUFAN Type: 4-pin P-type connector for +5V/+12V output
Pin Description Pin Description Pin Description Pin Description
1 +12V 2 Ground 3 Fan Speed detect 4 Fan Control
38
Power Output
Page 39
LS-570 User’s Manual Hardware Setup
2.16 <Indicator and Switch>
The JFRNT provides front control panel of the board, such as power button, reset and beeper, etc. Please check well before you connecting the cables on the chassis.
Connector: JFRNT Type: onboard 14-pin (2 x 7) 2.54-pitch header
Function Signal PIN Signal Function
IDE LED
Reset
Power
Button
HDLED+ 1 2 PWRLED+
HDLED- 3 4 N/C
Reset+ 5 6 PWRLED-
Reset- 7 8 SPK+
N/C 9 10 N/C
PWRBT+ 11 12 N/C
PWRBT- 13 14 SPK-
Power
LED
Speaker
1
JFRNT
14
Indicator and Switch
39
Page 40
LS-570 User’s Manual
(This Page is Left For Blank)
40
Page 41
LS-570 User’s Manual System Configuration
Chapter 3 <System Configuration>
3.1 <Video Memory Setup>
Based on Intel® 945GM(E) chipset with GMA (Graphic Media Accelerator) 950, the board supports Intel® DVMT (Dynamic Video Memory Technology) 3.0, which would allow the video memory to be allocated up to 224MB. To support DVMT, you need to install the Intel GMA 950 Driver with supported OS.
BIOS Setup:
On-Chip Video Memory Size: This option combines three items below for setup. On-Chip Frame Buffer Size:
This item can let you select video memory which been allocated for leg acy VGA and SVGA graphics support and compatibility. The available option is 1MB and 8MB.
Fixed Memory Size:
This item can let you select a static amount of page-locked graphics memory which will be allocated during driver initialization. Once you select the memory amount, it will be no longer available for system memory.
DVMT Memory Size:
This item can let you select a maximum size of dynamic amount usage of video memory, the system would configure the video memory depends on your application, this item is strongly recommend to be selected as MAX DVMT.
Video Memory Setup
41
Page 42
LS-570 User’s Manual System Configuration Fixed + DVMT Memory Size:
You can select the fixed amount and the DVMT amount at the same time for a guaranteed video memory and additional dynamic video memory, please check the table below for available setting.
System
Memory
128MB~255MB
256MB~511MB
512MB upper
Notice:
On-Chip
Frame
Buffer Size
1MB 32MB 0MB 32MB 1MB 0MB 32MB 32MB 8MB 32MB 0MB 32MB 8MB 0 32MB 32MB 1MB 64MB 0MB 64MB 1MB 0 64MB 64MB 1MB 128MB 0MB 128MB 1MB 0 128MB 128MB 1MB 64MB 64MB 128MB 8MB 64MB 0MB 64MB 8MB 0 64MB 64MB 8MB 128MB 0MB 128MB 8MB 0 128MB 128MB 8MB 64MB 64MB 128MB 1MB 64MB 0 64MB 1MB 0 64MB 64MB 1MB 128MB 0 128MB 1MB 0 128MB 128MB 1MB 64MB 64MB 128MB 8MB 64MB 0 64MB 8MB 0 64MB 64MB 8MB 128MB 0 128MB 8MB 0 128MB 128MB 8MB 64MB 64MB 128MB
Fixed
Memory
Size
DVMT
Memory
Size
Total Graphic Memory
1. The On-Chip Frame Buffer Size would be included in the Fixed Memory. Please select the memory size according to this table.
42
Video Memory Setup
Page 43
LS-570 User’s Manual System Configuration
3.2 <Audio Configuration>
The board provides 5.1 channel audio interface with driver installed, please install the Realtek ALC655 audio driver in the CD before getting start to enjoy the 5.1 channel sound system.
Audio Configuration
43
Page 44
LS-570 User’s Manual
(This Page is Left for Blank)
44
Page 45
LS-570 User’s Manual BIOS Setup
Chapter 4 <BIOS Setup>
The motherboard uses the Award BIOS for the system configuration. The Award BIOS in the single board computer is a customized version of the industrial standard BIOS for IBM PC AT-compatible computers. It supports Intel x86 and compatible CPU architecture based processors and computers. The BIOS provides critical low-level support for the system central processing, memory and I/O sub-systems.
The BIOS setup program of the single board computer let the customers modify the basic configuration setting. The settings are stored in a dedicated battery-backed memory, NVRAM, retains the information when the power is turned off. If the battery runs out of the power, then the settings of BIOS will come back to the default setting.
The BIOS section of the manual is subject to change without notice and is provided here for reference purpose only. The settings and configurations of the BIOS are current at the time of print, and therefore they may not be exactly the same as that displayed on your screen.
To activate CMOS Setup program, press <DEL> key i mmediately after you turn on the system. The following message “Press DEL to enter SETUP” should appear in the lower left hand corner of your screen. When you enter the CMOS Setup Utility, the Main Menu will be displayed as Figure 4-1. You can use arrow keys to select your function, press Enter key to accept the selection and enter the sub-menu.
Figure 4-1 CMOS Setup Utility Main Screen
BIOS Setup 45
Page 46
LS-570 User’s Manual
(This Page is Left for Blank)
46
Page 47
LS-570 User’s Manual I/O Port Pin Assignment
Appendix A <I/O Port Pin Assignment>
A.1 <IDE Port>
Connector: IDE Type: 44-pin (22 x 2) box header
Pin Description Pin Description
1 Reset 2 Ground 3 D7 4 D8 5 D6 6 D9 7 D5 8 D10 9 D4 10 D11 11 D3 12 D12 13 D2 14 D13 15 D1 16 D14 17 D0 18 D15 19 Ground 20 N/C 21 REQ 22 Ground 23 IOW-/STOP 24 Ground 25 IOR-/HDMARDY 26 Ground 27 IORDY/DDMARDY 28 Ground 29 DACK- 30 Ground 31 IRQ 32 N/C 33 A1 34 SD 35 A0 36 A2 37 CS1 38 CS3 39 ASP1 40 Ground 41 Vcc 42 Vcc 43 Ground 44 Ground
43
44
1
2
IDE Port
47
Page 48
LS-570 User’s Manual I/O Port Pin Assignment
A.2 <Floppy Port>
Connector: FDD Type: 26-pin connector
Pin Description Pin Description
1 VCC 2 INDEX 3 VCC 4 DRV0 5 VCC 6 DSKCHG 7 DRV1 8 N/C 9 MTR1 10 MTR0 11 RPM 12 DIR 13 N/C 14 STEP 15 Ground 16 WRITE DATA 17 Ground 18 WRITE GATE 19 N/C 20 TRACK 0 21 N/C 22 WRPTR 23 Ground 24 RDATA­25 Ground 26 SEL
A.3 <IrDA Port>
Connector: CN_IR Type: 5-pin header for SIR Port
Pin Description
1 Vcc 2 N/C 3 IRRX 4 Ground 5 IRTX
1 5
48
Floppy Port
Page 49
LS-570 User’s Manual I/O Port Pin Assignment
6
10
11 12
13 14 15
A.4 < CRT Port >
Connector: CRT Type: 15-pin D-sub female connector on panel
1 2 3 4 5
Pin Description Pin Description Pin Description
1 RED 6 Ground 11 N/C 2 GREEN 7 Ground 12 5VCDA 3 BLUE 8 Ground 13 HSYNC 4 N/C 9 LVGA5V 14 VSYNC 5 Ground 10 Ground 15 5VCLK
A.5 <Serial ATA Port>
1 7
Connector: SATA1/2 Type: 7-pin wafer connector
1 2 3 4 5 6 7
GND RSATA_TXP1 RSATA_TXN1 GND RSATA_RXN1 RSATA_RXP1 GND
5
A.6 <Serial Port>
Connector: COM1
4 3 2 1
Type: 9-pin D-sub male connector on rear panel
Pin Description Pin Description
1 DCD 6 DSR 2 SIN 7 RTS 3 SO 8 CTS 4 DTR 9 RI 5 Ground
CRT Port
9 8 7 6
49
Page 50
LS-570 User’s Manual I/O Port Pin Assignment
A.7 <LAN Port>
Connector: RJ45_1/2/3/4 Type: RJ45 connector with LED on rear panel
Pin 1 2 3 4 5 6 7 8
Description TX+ TX- RX+ N/C N/C RX- N/C N/C
1
8
A.8 <Parallel Port>
Connector: LPT (PRINTER) Type: 26-pin (2 x 13) 2.54-pitch box header
Pin Description Pin Description 1 STROBE- 14 AUTO FEED-
2 D0 15 ERROR­3 D1 16 INITIALIZE­4 D2 17 SELECT INPUT­5 D3 18 Ground 6 D4 19 Ground 7 D5 20 Ground 8 D6 21 Ground 9 D7 22 Ground 10 ACKNOWLEDGE- 23 Ground 11 BUSY 24 Ground 12 PAPER EMPTY 25 Ground 13 SELECT+ 26 N/C
14
1
26
13
50
LAN Port
Page 51
LS-570 User’s Manual Flash BIOS
Appendix B <Flash BIOS>
B.1 BIOS Auto Flash Tool
The board is based on Award BIOS and can be updated easily by the BIOS auto flash tool. You can download the tool online at the address below:
TUhttp://www.award.comUT TUhttp://www.commell.com.tw/support/support.htmUT
File name of the tool is “awdflash.exe”, it’s the utility that can write the data into the BIOS flash ship and update the BIOS.
B.2 Flash Method
1. Please make a bootable floppy disk.
2. Get the last .bin files you want to update and copy it into the disk.
3. Copy awardflash.exe to the disk.
4. Power on the system and flash the BIOS. (Example: C:/ awardflash XXX.bin)
5. Re-star the system.
Any question about the BIOS re-flash please contact your distributors or visit the web-site at below:
http://www.commell.com.tw/support/support.htm
BIOS Auto Flash Tool
51
Page 52
LS-570 User’s Manual System Resources
Appendix C <System Resources>
C1.<I/O Port Address Map>
52
I/O Port Address Map
Page 53
LS-570 User’s Manual System Resources
I/O Port Address Map
53
Page 54
LS-570 User’s Manual System Resources
C2.<Memory Address Map>
54
Memory Address Map
Page 55
LS-570 User’s Manual System Resources
C3.<System IRQ Resources>
System IRQ Resources
55
Page 56
LS-570 User’s Manual Watch Dog timer Setting
Appendix D <Watch Dog timer Setting >
The watchdog timer makes the system auto-reset while it stops to work for a period. The integrated watchdog timer can be setup as system reset mode by program.
Timeout Value Range
- 1 to 255
- Second or Minute
Program Sample
Watchdog timer setup as system reset with 5 second of timeout
2E, 87 2E, 87 2E, 07 2F, 08 Logical Device 8 2E, 30 Activate 2F, 01 2E, F5 Set as Second* 2F, 00 2E, F6 Set as 5 2F, 05
* Minute: bit 3 = 0; Second: bit 3 = 1
You can select Timer setting in the BIOS, after setting the time options, the system will reset according to the period of your selection.
56
Watch Dog timer Setting
Page 57
LS-570 User’s Manual
(This Page is Left for Blank)
57
Page 58
LS-570 User’s Manual Contact Information
Contact Information
Any advice or comment about our products and service, or anything we can help you please don’t hesitate to contact with us. We will do our best to support you for your products, projects and business.
Taiwan Commate Computer Inc.
19F., No.94, Sec. 1, Xintai 5th Rd., Xizhi Dist., New Taipei City
Address
TEL +886-2-26963909 FAX +886-2-26963911
22102, Taiwan
Website
E-Mail
Facebook
Twitter https://twitter.com/Taiwan_Commate
TUhttp://www.commell.com.twUT TUinfo@commell.com.twUT (General Information)
TUtech@commell.com.twUT (Technical Support)
https://www.facebook.com/pages/Taiwan-Commate-Computer-Inc/547993955271899
Commell is our trademark of industrial PC division
58
Contact Information
Loading...