COMMELL LP-180 User Manual

LP-180

Pico-ITX

User’s Manual

2013/7/29

Version: 1.3

LP-180 User’s Manual

Copyright

Copyright 2012. All rights reserved. This document is copyrighted and all rights are
reserved. The information in this document is subject to change without prior notice to
make improvements to the products.
This document contains proprietary information and pr otected by copyright. No part of
this document may be reproduced, copied, or translated in any form or any means
without prior written permission of the manufacturer.
All trademarks and/or registered trademarks contains in this document are propert y of
their respective owners.

Disclaimer

The company shall not be liable for any incidental or consequential damages resulting
from the performance or use of this product.
The company does not issue a warranty of any kind, express or implied, including
without limitation implied warranties of merchantability or fitness for a particular purpose.
The company has the right to revise the manual or include changes in the specifications
of the product described within it at any time without notice and without obligation to
notify any person of such revision or changes.

Trademark

All trademarks are the property of their respective holders.

Any questions please visit our website at TUhttp://www.commell.com.twUT

-1-

LP-180 User’s Manual

Packing List:

Please check the package content before you starting using the board.

Hardware:

LP-180 Pico-ITX Miniboard x 1

Cable Kit:

USB Cable x 1

(OALUSBA-3)

PS/2 keyboard & mouse cable x 1

(OALPS2/MK)

SATA Cable x 1

(OALSATA22B-PM15SH15)

DC_IN Power Cable x 1

(OALDC-B)

Audio Cable x 1

(OALPJ-HDUNB)

DVI Module With DVI Cable x 1

(BADPDVI_A + OALDVI-DF13)

(LP-180D Only)

Dual COM PORT cable

(OALES-BKU2NB)

LP-180D/X Heatsink with Fan x 1

(OHS-180F)

Printed Matters:

Driver CD x 1 (Including User’s Manual)

-2-

LP-180 User’s Manual

Index

Chapter 1 <Introduction>................................................................................. 6

1.1 <Product Overview>..............................................................................................6

1.2 <Product Specification>........................................................................................7

1.3 <Mechanical Drawing>.........................................................................................9

1.4 <Block Diagram>................................................................................................10

Chapter 2 <Hardware Setup>......................................................................... 11

2.1 <Connector Location>.........................................................................................11

2.2 <Jumper Reference>............................................................................................13

2.3 <Connector Reference>.......................................................................................14

2.3.1 <Internal Connector>........................................................................14

2.3.2 <External Connector>.......................................................................14

2.4 <Memory Setup>.................................................................................................15

2.5 <CMOS & ATX Setup>......................................................................................16

2.6 <SATA Interface>...............................................................................................17

2.8 <LAN Interface> .................................................................................................18

2.9 <Onboard Display Interface>..............................................................................19

2.9.1 <Analog VGA Interface>..................................................................19

2.9.2 <Digital Display> (LP-180X) ...........................................................20

2.9.3 <DVI Interface > (LP-180D).............................................................24

2.10 <Onboard Audio Interface>...............................................................................25

2.11 <USB2.0 Interface>...........................................................................................26

2.12 <Serial Port Jumper Setting >............................................................................27

2.13 <Power & FAN Connector >.............................................................................28

2.13.1 <Power Input>.................................................................................28

2.13.2 <Power Output>..............................................................................29

2.13.3 <Fan Connector>............................................................................. 29

2.14 <Indicator and Switch>......................................................................................31

Chapter 3 <BIOS Setup>................................................................................33

Appendix A <I/O Port Pin Assignment> .......................................................35

-3-

LP-180 User’s Manual

A.1 <SATA Port> .....................................................................................................35

A.2 < CRT Port > ......................................................................................................35

A.3 <LAN Port>........................................................................................................35

A.4 <LAN LED Port>............................................................................................... 36

A.5 <LPC Port> ........................................................................................................36

Appendix B <Flash BIOS>..............................................................................37

B.1 BIOS Auto Flash Tool.........................................................................................37

B.2 Flash Method...................................................................................................... 37

Appendix C <System Resources> ................................................................38

C.1 <I/O Port Address Map>.....................................................................................38

C.2 <Memory Address Map >...................................................................................40

C.3 < System IRQ Resources >................................................................................. 42

Appendix D <Watch Dog timer Setting >......................................................44

Appendix E <AMD Hing Definition Audio Device > .....................................45

Contact Information........................................................................................47

-4-

LP-180 User’s Manual

(This page is left for blank)

-5-

LP-180 User’s Manual

Chapter 1 <Introduction>

1.1 <Product Overview>

LP-180 is the PICO-ITX miniboard with AMD G-T56N platform, with onboard VGA,

Realtek ALC888 HD Codec audio, Giga LAN interface. Based on the AMD G-T56N
Processor , the board provides many advanced features for reduced power
consumption.

A55E Chipset

The board integrates AMD A55E, to provide built-in UniChrome Pro 3D / 2D Graphics
with MPEGII decoder, and supports DDR3 1066/1333 memory up to 4G of capacity.

18-bit LVDS LCD interface

The board provides onboard 18-bit LVDS LCD interface, supports up to 1400 x 1050 of
UXGA high resolution.

Flexible Extension Interface

The board also provides one Mini card socket.

-6-

LP-180 User’s Manual

1.2 <Product Specification>

General Specification

Form Factor PICO-ITX miniboard
CPU AMD G-Series T56N Processor 1.65GHz
Memory 1 x 204-pin DDR3 1066/1333 SO-DIMM SDRAM up to 4G
Chipset AMD A55E FCH
Watchdog Timer System reset programmable watchdog timer with 1 ~ 255

sec./min. of timeout value
Real Time Clock Chipset integrated RTC with onboard lithium battery
Serial ATA 1 x serial ATAII interface with 300MB/s transfer rate

(Only 2.5” HDD and No RAID Function)

Multi-I/O Port

Chipset Winbond W83627DHG-P
Serial Port Two RS-232 serial port
USB Port Four Hi-Speed USB 2.0 ports with 480Mbps of transfer rate
K/B & Mouse PS/2 keyboard and mouse port

VGA Display Interface

Chipset AMD G-Series T56N Processor
Frame Buffer Up to 512MB shared with system memory
Display Type CRT, LCD monitor with analog display, single channel

LVDS(LP-180X only), DVI(LP-180D only)

Connector External DB15 female connector

5-Pin(molex_53261) LCD Backlight inverter connector and

Onboard 20-Pin(DF13-20DP) header

(LP-180X is LVDS signal)

(LP-180D is DVI signal)

Ethernet Interface

Controller 1 x Intel® 82583V Gigabit Ethernet controller
Type Triple speed 10/100/1000Base-T

auto-switching Fast Ethernet

Full duplex, IEEE802.3U compliant

Connector One External RJ45 connector with LED

Audio Interface

Chipset REALTEK ALC888
Interface Stereo audio Line-out and MIC-in

Connector Onboard audio connector with pin header

Expansive Interface

PCIE Mini Card 1 x PCIE Mini Card socket

Power and Environment

-7-

LP-180 User’s Manual

Power Requirement DC only +5V input with onboard 2-pin connector
Dimension 100 (L) x 72(H) mm
Temperature Operating within 0 ~ 60℃

Storage within -20 ~ 85℃

Ordering Code

LP-180D Same as LP-180, support DVI

LP-180X Same as LP-180, support Chipset Integrated 18-bit single

channel LVDS

The specifications may be different as the actual production.
For further product information please visit the website at

TUhttp://www.commell.com.twUT

-8-

LP-180 User’s Manual

1.3 <Mechanical Drawing>

9-

-

LP-180 User’s Manual

1.4 <Block Diagram>

CRT / DVI / LVDS

HD Audio

2 x Serial Port

AMD

DDR3 SODIMM 4GB max.

G-T56N

Mini card socket

A55E

4 x USB port

1 x SATA

PS2 KB/MS

Giga LAN

W83627DHG-P

10-

-

LP-180 User’s Manual

Chapter 2 <Hardware Setup>

2.1 <Connector Location>

CPUFAN

CN_DDP

JFRNT

DC_IN

SYSFAN

MINI_CARD

CN_COM1/2

CN_SATA

CN_USB1

CN_LPC

CN_USB2

CN AUDIO

11-

-

LP-180 User’s Manual

CN_INV

LP-180

DC_OUT

SO-DIMM

RJ45 PS2 CRT

12-

-

LP-180 User’s Manual

2.2 <Jumper Reference>

Jumper Function

JRTC CMOS Operating/Clear Setting
JAT AT/ATX Mode Setting
JVLCD LCD Panel Voltage Setting

JVLCD

JRTC

JAT

13-

-

LP-180 User’s Manual

2.3 <Connector Reference>

2.3.1 <Internal Connector>

Connector Function Remark

SO-DIMM 204 -pin DDR3 SO-DIMM SDRAM slot
CN_SATA 10-pin SATA Cable connector
MINI_CARD PCIE mini card socket
CN_DDP 20 –pin(DF13-20DP) header

(LP-180X is LVDS signal)

(LP-180D is DVI signal)

CN_INV 5-pin LCD Backlight inverter connector
CN_USB1/2 5 x 2-pin USB connector
CN_AUDIO 5 x 2-pin audio connector
CN_LPC 5 x 2-pin header for LPC Port
JFRNT 10-pin switch/indicator connector
CPUFAN 4-pin CPU cooler fan connector
SYSFAN 3-pin system cooler fan connector
DC_OUT 6-pin power output connector
DC_IN DC input connector

2.3.2 <External Connector>

Connector Function Remark

CRT DB15 VGA connector
PS2 PS/2 keyboard and mouse connector
RJ45 RJ45 LAN connector

14-

-

LP-180 User’s Manual

2.4 <Memory Setup>

The board provides one 204-pin DDR3 SO-DIMM to support DDR3 1066/1333 mem ory
modules up to 4GB. Only Non-ECC memory is supported.

15-

-

SO-DIMM

LP-180 User’s Manual

2.5 <CMOS & ATX Setup>

The board’s data of CMOS can be setting in BIOS. If the board refuses to boot due to
inappropriate CMOS settings, please remove battery to clear (reset) the CMOS to its
default values.

3 1

JAT

3 1

JRTC

The board has a jumper to switch AT power mode (automatic power on) or standard
ATX mode.

Jumper: JAT
Type: onboard 3-pin jumper

JAT Mode

1-2 AT Mode
2-3 ATX Mode

Default setting

Jumper: JRTC
Type: onboard 3-pin jumper

JRTC Mode

1-2 Clear CMOS
2-3 Normal Operation

Default setting

Battery

16-

-

LP-180 User’s Manual

2.6 <SATA Interface>

Based on AMD A55E, the board provides one Serial ATAII interfaces with up to 300MB/s
of transfer rate.

CN_SATA

DC_OUT

Remark: Only catch 2.5” HDD

17-

-

LP-180 User’s Manual

2.8 <LAN Interface>

The board integrates with one Intel 82583V Gigabit Ethernet controller. The Intel®
82583V supports triple speed of 10/100/1000Base-T, with IEEE802.3 compliance and
Wake-On-LAN supported.

LAN

18-

-

LP-180 User’s Manual

2.9 <Onboard Display Interface>

Based on AMD G-T56N chipset with built-in AMD Radeon HD 6300 series Graphics, the
board provides one DB15 connector on real external I/O port, and one 20-pin DVI
(LP-180D) or one LVDS interface with 5-pin LCD backlight inverter connector(LP-180X).
The board provides dual display function with clone mode and extended desktop mode
for CRT, DVI (LP-180D) or LVDS (LP-180X).

2.9.1 <Analog VGA Interface>

Please connect your CRT or LCD monitor with DB15 male connector to the onboard
DB15 female connector on rear I/O port.
The board supports up to 1920 x 1200 (WUXGA) of resolution.

CRT

19-

-

LP-180 User’s Manual

2.9.2 <Digital Display> (LP-180X only)

The board provides one 20-pin LVDS connector for 18 bit single channel panel, supports
up to 1400 x 1050 of resolution, with one LCD backlight inverter connector and one
jumper for panel voltage setting.

19

220

CN_DDP

1

3
1

JVLCD

1

CN_INV

5

20-

-

LP-180 User’s Manual

Connector: CN_INV
Type: 5-pin Inverter power connector
Connector model: molex_53261-5pin or compatible

Pin Description

1 +3.3V
2 GND
3 +5V
4 GND
5 Enable

Jumper: JVLCD
Type: 3-pin Power select jumper

Pin Description

1-2 +5V
2-3 +3.3V

Default: 2-3

Connector: CN_DDP
Type: onboard 20-pin connector for LVDS connector
Connector model: HIROSE DF13-20DP-1.25V or compatible

Pin Signal Pin Signal

1 LCDVCC 2 LCDVCC
3 HPD0 4 GND
5 TX0N 6 TX0P
7 GND 8 TX1N

9 TX1P 10 GND
11 TX2N 12 TX2P
13 GND 14 CLKN
15 CLKP 16 GND
17 DVI_DA(LP-180D) 18 DVI_SL(LP-180D)
19 AUXN 20 AUXP

21-

-

LP-180 User’s Manual

To setup the LCD, you need the component below:

1. A panel with LVDS interfaces.

2. An inverter for panel’s backlight power.

3. A LCD cable and an inverter cable.

For the cables, please follow the pin assignment of the connector to make a c able, becaus e
every panel has its own pin assignment, so we do not provide a standard cable; ple ase fin d
a local cable manufacture to make cables.

LCD Installation Guide:

1. Preparing the LP-180, LCD panel and the backlight inverter

2. You would need a LVDS type cable.

Panel side

3.

To connect all of the devices well.

For sample illustrator only

22-

-

Board side

LP-180 User’s Manual

After setup the devices well, you need to select the LCD panel
type in the BIOS.

The panel type mapping is list below:

LP-180 BIOS panel type selection form

On board Single channel LVDS

18bit

NO. Output format

1 800 x 600
2 1024 x 768
3 1280 x 720
4 1280 x 800
5 1280 x 1024
6 1366 x 768
7 1440 x 900

23-

-

LP-180 User’s Manual

2.9.3 <DVI Interface > (LP-180D only)

The board also comes with a DVI interface. Supports up to 1920 x 1200 (WUXGA) of
resolution.

Connector: CN_DDP
Type: onboard 20-pin connector for DVI connector
Connector model: HIROSE DF13-20DP-1.25V or compatible

Pin Number Assignment Pin Number Assignment

1 LCDVCC 2 LCDVCC
3 HPD0 4 GND
5 TX0N 6 TX0P
7 GND 8 TX1N

9 TX1P 10 GND
11 TX2N 12 TX2P
13 GND 14 CLKN
15 CLKP 16 GND
17 DVI_DA 18 DVI_SL
19 AUXN 20 AUXP

24-

-

LP-180 User’s Manual

2.10 <Onboard Audio Interface>

The board provides the onboard high definition audio with Realtek ALC888

Connector: CN_AUDIO

Type: 10-pin (2 x 5) 1.27mm x 2.54mm-pitch header

Pin Description Pin Description

1 MIC2_L 2 AGND
3 MIC2_R 4 AVCC
5 FP_OUT_R 6 MIC2_JD
7 SENSE_B 8 N/C
9 FP_OUT_L 10 LINE2_JD

25-

-

2 10

CN_AUDIO

1 9

LP-180 User’s Manual

2.11 <USB2.0 Interface>

Based on AMD A55E FCH, the board provides 4 USB2.0 ports. The USB2.0 interface
provides up to 480Mbps of transferring rate.

Interface USB2.0

Controller A55E

Transfer Rate Up to 480Mb/s

Output Current 500mA

10 9

2 10

1 9

2 1

CN_USB1

CN_USB2

Connector: CN_USB
Type: 10-pin (5 x 2) header for USB Port

Pin Description Pin Description

1 VCC 2 VCC
3 D0- 4 D1­5 D0+ 6 D1+
7 Ground 8 Ground
9 Ground 10 N/C

PS: The USB2.0 will be only active when you connecting with the USB2.0 devices, if you
insert an USB1.1 device, the port will be changed to USB1.1 protocol automatically. The
transferring rate of USB2.0 as 480Mbps is depends on device capacity, exact
transferring rate may not be up to 480Mbps.

26-

-

LP-180 User’s Manual

2.12 <Serial Port Jumper Setting >

The board provides two RS232 serial ports

Connector: CN_COM1/2
Type: 20-pin (10 x 2) 1.27mm x 2.54mm-pitch header for COM1/2

Pin Description Pin Description

1 MDCD1- 2 MSIN1­3 MSO1- 4 MDTR1­5 N/C 6 MDSR1­7 MRTS1- 8 MCTS1­9 MRI1- 10 N/C
11 MDCD2- 12 MSIN2­13 MSO2- 14 MDTR2­15 GND 16 MDSR2­17 MRTS2- 18 MCTS2­19 MRI2- 20 N/C

27-

-

20 19

2 1

LP-180 User’s Manual

2.13 <Power & FAN Connector >

The board requires DC input with 2-pin header, the input voltage range is from 5V for the
input current, please take a reference of the power consumption report on appendix.

2.13.1 <Power Input>

Connector: DC_IN

Type: 2-pin header

Pin Description Pin Description

1 Ground 2 +5V

Remark: DC input voltage only +5V

2
1

DC_IN

28-

-

LP-180 User’s Manual

_

3

1

3

1

2.13.2 <Power Output>

Connector: DC_OUT
Type: 6-pin connector for +5V output

Pin Description Pin Description Pin Description

1 N/C 2 N/C 3 Ground
4 Ground 5 +5V 6 +5V

Note: Maximum output current 5V/1A

2.13.3 <Fan Connector>

Connector: SYSFAN
Type: 3-pin fan wafer connector

Connector model: 2001-WS-03-LF

Pin Description Pin Description Pin Description

1 Ground 2 +5V 3 CSFAN

Connector: CPUFAN
Type: 3-pin fan wafer connector

Connector model: 2001-WS-03-LF

Pin Description

1 Ground

2 +5V

3 P1FAN

DC

SYSFAN

CPUFAN

29-

-

1 6

OUT

LP-180 User’s Manual

30-

-

LP-180 User’s Manual

2.14 <Indicator and Switch>

The JFRNT provides front control panel of the board, such as power button, reset and
beeper, etc. Please check well before you connecting the cables on the chassis.

Connector: JFRNT
Type: onboard 10-pin (2 x 5) 2.54-pitch header

Function Signal PIN Signal

Power

Speaker

HDD LED

Power LED

Reset

10

2

9

1

JFRNT

PWRBT- 1 2 PWRBT+

SPK- 3 4 SPK+

HLED- 5 6 HLED+

GND 7 8 PWLED+

Reset- 9 10 GND

31-

-

LP-180 User’s Manual

(This Page is Left For Blank)

32-

-

LP-180 User’s Manual

Chapter 3 <BIOS Setup>

The motherboard uses the Award BIOS for the system configuration. The Award
BIOS in the single board computer is a customized version of the industrial standard
BIOS for IBM PC AT-compatible computers. It supports Intel® x86 and compatible
CPU architecture based processors and computers. The BIOS provides critical
low-level support for the system central processing, memory and I/O sub-systems.

The BIOS setup program of the single board computer let the customers modif y the
basic configuration setting. The settings are stored in a dedicated battery-backed
memory, NVRAM, retains the information when the power is turned off. If the battery
runs out of the power, then the settings of BIOS will come back to the default setting.

The BIOS section of the manual is subject to change without notice and is provi ded
here for reference purpose only. The settings and configurations of the BIOS are
current at the time of print, and therefore they may not be exactly the same as that
displayed on your screen.

To activate CMOS Setup program, press ＜DEL＞ key immediately after you turn
on the system. The following message “Press DEL to enter SETUP” should appear in
the lower left hand corner of your screen. When you e nter the CMOS Setup Utility,
the Main Menu will be displayed as Figure 4-1. You can use arrow keys to select
your function, press ＜Enter＞ key to accept the selection and enter the sub-menu.

Figure 4-1 CMOS Setup Utility Main Screen

33-

-

LP-180 User’s Manual

(This Page is Left for Blank)

34-

-

LP-180 User’s Manual

Appendix A <I/O Port Pin Assignment>

A.1 <SATA Port>

Connector: SATA
Type: 10-pin header for SATA Port

Pin Description Pin Description

1 Ground 2 TXP
3 TXN 4 Ground
5 N/C 6 N/C
7 Ground 8 RXN
9 RXP 10 Ground

A.2 < CRT Port >

Connector: CRT
Type: 15-pin D-sub female connector on rear panel

Pin Description Pin Description Pin Description

1 RED 6 Ground 11 N/C
2 GREEN 7 N/C 12 5VCDA
3 BLUE 8 Ground 13 HSYNC
4 N/C 9 LVGA5V 14 VSYNC
5 -CRTATCH 10 -CRTATCH 15 5VCLK

110

5 1

10 6

15 11

A.3 <LAN Port>

Connector: RJ45
Type: RJ45 connector with LED on rear panel

Pin 1 2 3 4 5 6 7 8

Description TRD0+ TRD0- TRD1+ TRD2+ TRD2- TRD1- TRD3+ TRD3-

35-

-

8 1

LP-180 User’s Manual

A.4 <LAN LED Port>

Connector: JSPD1
Type: 2-pin header for LAN Speed LED connector RJ45 connector with LED on
rear panel

When Lan speed 10/100Mbps

Pin Description

1 LED­2 LED+

When Lan speed 1Gbps

Pin Description

1 LED+
2 LED-

2
1

Connector: JACT1
Type: 5-pin header for LAN Activity LED connector

Pin Description

1 LED­2 LED+

2
1

A.5 <LPC Port>

Connector: CN_LPC
Type: 10-pin header for LPC Port

Pin Description Pin Description

1 LPC_CLK 2 RESET­3 LFRAME- 4 LAD3
5 LAD2 6 LAD1
7 LAD0 8 +3.3V
9 Ground 10 Ground

36-

-

10 9

2 1

LP-180 User’s Manual

Appendix B <Flash BIOS>

B.1 BIOS Auto Flash Tool

The board is based on Award BIOS and can be updated easily by the BIOS auto
flash tool. You can download the tool online at the address below:

http://www.phoenix.com/en/home/

http://www.commell.com.tw/Support/Support_SBC.htm

File name of the tool is “Pflash.exe”, it’s the utility that can write the data into the
BIOS flash ship and update the BIOS.

B.2 Flash Method

1. Please make a bootable floppy disk.

2. Get the last .bin files you want to update and copy it into the disk.

3. Copy awardflash.exe to the disk.

4. Power on the system and flash the BIOS.

(Example: C:/Pflash /sa /bbl /cvar XXX.bin)

5. Re-star the system.

Any question about the BIOS re-flash please contact your distributors or visit the
web-site at below:

http://www.commell.com.tw/support/support.htm

37-

-

LP-180 User’s Manual

Appendix C <System Resources>

C.1 <I/O Port Address Map>

38-

-

LP-180 User’s Manual

39-

-

LP-180 User’s Manual

C.2 <Memory Address Map >

40-

-

LP-180 User’s Manual

41-

-

LP-180 User’s Manual

C.3 < System IRQ Resources >

42-

-

LP-180 User’s Manual

43-

-

LP-180 User’s Manual

Appendix D <Watch Dog timer Setting >

The watchdog timer makes the system auto-reset while it stops to work for a period. The
integrated watchdog timer can be setup as system reset mode by program.

Timeout Value Range

- 1 to 255

- Second or Minute

Program Sample

Watchdog timer setup as system reset with 5 second of timeout

2E, 87
2E, 87
2E, 07
2F, 08 Logical Device 8
2E, 30
2F, 01 Activate
2E, F5
2F, 02 Set as Second*
2E, F6
2F, 05 Set as 5

* Minute: bit 3 = 1; Second: bit 3 = 0

You can select Timer setting in the BIOS, after setting the time options, the system
will reset according to the period of your selection.

44-

-

LP-180 User’s Manual

Appendix E <AMD Hing Definition Audio Device >

1. Copy the CD Driver folder to disk, Ex: C:\ , D:\ …

2. Please choose “Device Manager”

3. You can see other devices ”Audio Device on High Definition Audio Bus”

4. Please choose “Audio Device on High Definition Audio Bus” then press
Update Driver

5. Please choose ”NO, not this time“

6. Install software for ” Audio Device on High Definition Audio Bus ” Please choose ”Install
from a list or specific location”

7. Please choose “Search for the best driver in these location” Check “Include this location
in the search” then press “Browse”

8. Please select the file location”D:\LP-180\Audio(XP)\XP”

45-

-

LP-180 User’s Manual

9. Install finish

(This Page is Left for Blank)

46-

-

LP-180 User’s Manual

Contact Information

Any advice or comment about our products and service, or
anything we can help you please don’t hesitate to contact with us.
We will do our best to support you for your products, projects and
business.

Taiwan Commate Computer Inc.

Address

TEL [phone]
FAX [phone]
Website
E-Mail

Facebook

Twitter https://twitter.com/Taiwan_Commate

19F., No.94, Sec. 1, Xintai 5th Rd., Xizhi Dist., New Taipei
City 22102, Taiwan

TUhttp://www.commell.com.twUT
[e-mail] (General Information)

[e-mail] (Technical Support)

https://www.facebook.com/pages/Taiwan-Commate-Computer-Inc/547993955271899

Commell is our trademark of industrial PC division

47-

-