Page 1
LP-172
Pico-ITX
User’s Manual
2014/3/14
Version:1.7
Page 2
LP-172 User’s Manual
Copyright
Copyright 2012. All rights reserved. This document is copyrighted and all rights are
reserved. The information in this document is subject to change without prior notice to
make improvements to the products.
This document contains proprietary information and pr otected by copyright. No part of
this document may be reproduced, copied, or translated in any form or any means
without prior written permission of the manufacturer.
All trademarks and/or registered trademarks contains in this document are propert y of
their respective owners.
Disclaimer
The company shall not be liable for any incidental or consequential damages resulting
from the performance or use of this product.
The company does not issue a warranty of any kind, express or implied, including
without limitation implied warranties of merchantability or fitness for a particular purpose.
The company has the right to revise the manual or include changes in the specifications
of the product described within it at any time without notice and without obligation to
notify any person of such revision or changes.
Trademark
All trademarks are the property of their respective holders.
Any questions please visit our website at TUhttp://www.commell.com.twUT
-1-
Page 3
LP-172 User’s Manual
Packing List:
Please check the package content before you starting using the board.
Hardware:
LP-172 Pico-ITX Miniboard x 1
Cable Kit:
USB Cable x 1
(OALUSBA-3)/ (1040173)
Dual COM PORT cable
OALES-BKU2NB)/ (1040090)
Audio Cable x 1
(OALPJ-HDUNB)/ (1040123)
LP-172N Heatsink x 1
(OHS-172)/ (2181110001)
(OALSATA22B-PM15SH15)/ (1040512)
SATA Cable x 1
DC_IN Power Cable x 1
(OALDC-B)/ (1040513)
PS/2 keyboard & mouse cable x 1
(OALPS2/MKN)/ (1040551)
LP-172D5 Heatsink with Fan x 1
(OHS-172F)/ (2181010013)
Printed Matters:
Driver CD x 1 (Including User’s Manual)
-2-
Page 4
LP-172 User’s Manual
Index
Chapter 1 <Introduction>.............................................................6
1.1 <Product Overview>...............................................................................6
1.2 <Product Specification>..........................................................................7
1.3 <Mechanical Drawing>...........................................................................9
1.4 <Block Diagram>..................................................................................10
Chapter 2 <Hardware Setup>..................................................11
2.1 <Connector Location>..........................................................................11
2.2 <Jumper Reference>............................................................................13
2.3 <Connector Reference>.......................................................................14
2.3.1 <Internal Connector>...........................................................14
2.3.2 <External Connector> .........................................................14
2.4 <Memory Setup>..................................................................................15
2.5 <CMOS & ATX Setup>.........................................................................16
2.6 <SATA Interface>.................................................................................17
2.7 <LAN Interface> ...................................................................................18
2.8 <Onboard Display Interface> ...............................................................19
2.8.1 <Analog VGA Interface> .....................................................19
2.8.2 <CN_LVDS>........................................................................20
2.9 <Onboard Audio Interface>..................................................................24
2.10 <USB2.0 Interface>............................................................................25
2.11 <Serial Port Jumper Setting > ............................................................26
2.12 <Power & FAN Connector >...............................................................27
2.12.1 <Power Input>...................................................................27
2.12.2 <Power Output>................................................................28
2.12.3 <Fan Connector> ..............................................................29
2.13 <Indicator and Switch>.......................................................................30
Chapter 3 <BIOS Setup>............................................................32
Appendix A <I/O Port Pin Assignment>..........................34
A.1 <SATA Port>........................................................................................34
-3-
Page 5
LP-172 User’s Manual
A.2 <CRT Port>..........................................................................................34
A.3 <LAN Port> ..........................................................................................34
A.4 <LAN LED Port> ..................................................................................35
A.5 <LPC Port> ..........................................................................................35
Appendix B <Flash BIOS>.........................................................36
B.1 BIOS Auto Flash Tool...........................................................................36
B.2 Flash Method .......................................................................................36
Appendix C <System Resources>......................................37
C.1 <I/O Port Address Map>......................................................................37
C.2 <Memory Address Map>......................................................................39
C.3 <System IRQ Resources>...................................................................40
Appendix D <Watch Dog timer Setting>.........................43
Contact Information.......................................................................45
-4-
Page 6
LP-172 User’s Manual
(This page is left for blank)
-5-
Page 7
LP-172 User’s Manual
Chapter 1 <Introduction>
1.1 <Product Overview>
LP-172 is the PICO-ITX miniboard with Intel® Atom™ CedarTrail Processor with
optional D2550 or N2800 platform, Intel® NM10, integrated Intel® GMA 3650 graphics,
DDR3 SO-DIMM memory, Realtek ALC888 HD Codec audio and one Intel® 82583V
Giga LAN.
Intel® Atom D2550 Processor
The Intel® Atom D2550 Dual core processor is with, 1.86GHz clock Speed, 1MB L2
cache. It's built on 32nm process technology support Hyper-Threading Technology,
Intel® 64.
Intel® Atom N2800 Processor
The Intel® Atom N2800 Dual core processor is with, 1.86GHz clock Speed, 1MB L2
cache. It's built on 32nm process technology support Hyper-Threading Technology,
Enhanced Intel Speedstep® Technology, Intel® 64.
Intel® NM10 Chipset
The board integrates Intel® NM10. The chipset features power-efficient graphics with an
integrated 32-bit 3D graphics engine based on Intel® Graphics Media Accelerator 3650
architecture with DVI, LVDS, CRT display ports. It provides I/O capabilities and flexibility
via high-bandwidth interfaces such as PCIE and Hi-Speed USB 2.0 connectivity. It also
includes a single channel for 1066 MHz DDR3 system memory (SODIMM), HD Audio.
Flexible Extension Interface
The board also provides one Mini card socket.
-6-
Page 8
LP-172 User’s Manual
1.2 <Product Specification>
General Specification
Form Factor PICO-ITX miniboard
CPU
Memory 1 x 204-pin DDR3 800/1066 SO-DIMM SDRAM up to 4G
Chipset Intel® NM10
Watchdog Timer
Real Time Clock Chipset integrated RTC with onboard lithium battery
Serial ATA
Multi-I/O Port
Chipset Winbond W83627DHG-P
Serial Port Two RS-232 serial port
USB Port Four Hi-Speed USB 2.0 ports with 480Mbps of transfer rate
K/B & Mouse PS/2 keyboard and mouse port
VGA Display Interface
Chipset Intel® integrated extreme GMA 3650
Display Type CRT, LCD monitor with analog display, single channel LVDS
Connector
Ethernet Interface
Controller 1 x Intel® 82583V Gigabit Ethernet controller
Type
Connector 1 X External RJ 45 connector with LED
Audio Interface
Chipset REALTEK ALC888
Interface Stereo audio Line-out and MIC-in
Connector Onboard au dio connector with pin header
Expansive Interface
PCIE Mini Card 1 x PCIE Mini Card socket
Power and Environment
Power Requirement DC only +5V input with onboard 2-pin connector
Dimension 100 (L) x 72(H) mm
Temperature
Intel® Atom™ CedarTrail Processor with optional D2550 or
N2800
System reset programmable watchdog timer with 1 ~ 255
sec./min. of timeout value
1 x serial ATAII interface with 300MB/s transfer rate
(No RAID Function)
External DB15 female connector
Onboard 20-Pin LVDS and 5-Pin inverter connector
Triple speed 10/100/1000Base-T
auto-switching Fast Ethernet
Full duplex, IEEE802.3U compliant
Operating within 0 ~ 60℃
Storage within -20 ~ 85℃
-7-
Page 9
LP-172 User’s Manual
Ordering Code
Support Intel® Atom™ CedarTrail D2550 processor with
LP-172D5
onboard VGA, 18 or 24 bit LVDS, Audio, Giga LAN,
USB2.0 .SATAII, PCIE mini card
Support Intel® Atom™ CedarTrail D2550 processor with
LP-172D5S
onboard VGA, 18 or 24 bit LVDS, Audio, Giga LAN,
USB2.0 .SATAII, PCIE mini card mSATA
Support Intel® Atom™ CedarTrail N2800 processor with
LP-172N
onboard VGA, 18 bit LVDS, Audio, Giga LAN,
USB2.0 .SATAII, PCIE mini card
Support Intel® Atom™ CedarTrail N2800 processor with
LP-172NS
onboard VGA, 18 bit LVDS, Audio, Giga LAN,
USB2.0 .SATAII, PCIE mini card mSATA
The specifications may be different as the actual production.
For further product information please visit the website at
TUhttp://www.commell.com.twUT
-8-
Page 10
LP-172 User’s Manual
1.3 <Mechanical Drawing>
9-
-
Page 11
LP-172 User’s Manual
1.4 <Block Diagram>
HD Audio
Giga LAN
CRT / LVDS
PS2 KB/MS
Intel Atom
D2550/N2800
Intel
NM10
W83627DHG-P
DDR3 SO-DIMM 4GB max.
PCIE Mini card
4 x USB port
1 x SATA
2 x Serial Port
10-
-
Page 12
LP-172 User’s Manual
Chapter 2 <Hardware Setup>
2.1 <Connector Location>
CPUFAN
CN_LVDS
JFRNT
DC_IN
SYSFAN
MINI_CARD
CN_COM1/2
CN_SATA
CN_USB1
CN_LPC
CN_USB2
CN AUDIO
11-
-
Page 13
LP-172 User’s Manual
CN_INV
LP-172
RJ45 PS2 CRT
DC_OUT
SO-DIMM
12-
-
Page 14
LP-172 User’s Manual
2.2 <Jumper Reference>
Jumper Function
JRTC CMOS Operating/Clear Setting
JAT AT/ATX Mode Setting
JVLCD LCD Panel Voltage Setting
JVLCD
JRTC
JAT
13-
-
Page 15
LP-172 User’s Manual
2.3 <Connector Reference>
2.3.1 <Internal Connector>
Connector Function Remark
SO-DIMM 204 -pin DDR3 SO-DIMM SDRAM slot
CN_SATA 10-pin SATA Cable connector
MINI_CARD PCIE mini card socket
CN_INV 5-pin LCD inverter connector
CN_USB1/2 5 x 2-pin USB connector
CN_AUDIO 5 x 2-pin audio connector
CN_LPC 5 x 2-pin header for LPC Port
CN_COM1/2 10 x 2-pin com connector
JFRNT 10-pin switch/indicator connector
CPUFAN 4-pin CPU cooler fan connector
SYSFAN 3-pin system cooler fan connector
DC_OUT 6-pin power output connector
DC_IN DC input connector
2.3.2 <External Connector>
Connector Function Remark
CRT DB15 VGA connector
PS2 PS/2 keyboard and mouse connector
RJ45 RJ45 LAN connector
14-
-
Page 16
LP-172 User’s Manual
2.4 <Memory Setup>
Non-ECC, unbuffered memory is supported only.
The board provides one 204-pin DDR3 SO-DIMM to support DDR3 800/1066 memory
modules up to 4GB.
Suggestion:
DDR3 SO-DIMM Modules:
–Raw Card C = Single-sided x 8
–Raw Card F = Double-sided x 8
15-
-
SO-DIMM
Page 17
LP-172 User’s Manual
2.5 <CMOS & ATX Setup>
The board’s data of CMOS can be setting in BIOS. If the board refuses to boot due to
inappropriate CMOS settings, please remove battery to clear (reset) the CMOS to its
default values.
3 1
JAT
3 1
JRTC
The board has a jumper to switch AT power mode (automatic power on) or standard
ATX mode.
Jumper: JAT
Type: onboard 3-pin jumper
JAT Mode
1-2 AT Mode
2-3 ATX Mode
Default setting
Jumper: JRTC
Type: onboard 3-pin jumper
JRTC Mode
1-2 Clear CMOS
2-3 Normal Operation
Default setting
Battery
16-
-
Page 18
LP-172 User’s Manual
2.6 <SATA Interface>
Based on Intel NM10, the board provides one Serial A TAII interfaces with up to 300MB/s
of transfer rate.
CN_SATA
DC_OUT
17-
-
Page 19
LP-172 User’s Manual
2.7 <LAN Interface>
The Intel® 82583V supports triple speed of 10/100/1000Base-T, with IEEE802.3
compliance and Wake-On-LAN supported.
LAN
18-
-
Page 20
LP-172 User’s Manual
2.8 <Onboard Display Interface>
Based on Intel Atom CedarTrail Processor chipset with built-in Intel® integrated extreme
GMA 3650, the board provides one DB15 connector on real external I/O port, and LVDS
interface with 5-pin LCD backlight inverter connector. The board provides dual display
function with clone mode and extended desktop mode for CRT and LVDS.
2.8.1 <Analog VGA Interface>
Please connect your CRT or LCD monitor with DB15 male connector to the onboard
DB15 female connector on rear I/O port.
The board supports up to 1920 x 1080 (WUXGA) of resolution.
CRT
19-
-
Page 21
LP-172 User’s Manual
2.8.2 <CN_LVDS>
The board provides one 20-pin LVDS connector for 18 bit or 24bit single channel panel,
with one LCD backlight inverter connector and one jumper for panel voltage setting.
2 20
CN_LVDS
1
19
3
1
JVLCD
1
5
CN_INV
20-
-
Page 22
LP-172 User’s Manual
Connector: CN_INV
Type: 5-pin Inverter power connector
Connector model: molex_53261-5pin or compatible
Pin Description
1 +3.3V
2 CTLBKL
3 +5V
4 GND
5 Enable
Jumper: JVLCD
Type: 3-pin Power select jumper
Pin Description
1-2 +5V
2-3 +3.3V
Default: 2-3
Connector: CN_LVDS Type: onboard 20-pin connector for LVDS connector
Connector model:
E&T 3950-B20C-00R or similar (HIROSE DF13-20DP-1.25V compatible)
Pin Signal Pin Signal
1 LCDVCC 2 LCDVCC
3 NC 4 GND
5 TX0N 6 TX0P
7 GND 8 TX1N
9 TX1P 10 GND
11 TX2N 12 TX2P
13 GND 14 TXCN
15 TXCP 16 GND
17 TXL3N
(LP-172D5)
19 NC 20 NC
21-
-
18 TXL3P
(LP-172D5)
Page 23
LP-172 User’s Manual
To setup the LCD, you need the component below:
1. A panel with LVDS interfaces.
2. An inverter for panel’s backlight power.
3. A LCD cable and an inverter cable.
For the cables, please follow the pin assignment of the connector to make a c able, becaus e
every panel has its own pin assignment, so we do not provide a standard cable; ple ase fin d
a local cable manufacture to make cables.
LCD Installation Guide:
1. Preparing the LP-172, LCD panel and the backlight inverter
2. You would need a LVDS type cable.
Panel side
3.
To connect all of the devices well.
For sample illustrator only
22-
-
Board side
Page 24
LP-172 User’s Manual
After setup the devices well, you need to select the LCD panel type in the BIOS.
The panel type mapping is list below:
LP-172 BIOS panel type selection form
On board Single channel LVDS
18bit (LP-172N) 24bit (LP-172D5)
NO. Output format Output format
1 640 x 480 640 x 480
2 800 x 600 800 x 600
3 1024 x 768 1024 x 768
4 1280 x 1024 1280 x 1024
5 1366 x 768 1366 x 768
6 1280 x 800 1280 x 800
23-
-
Page 25
LP-172 User’s Manual
2.9 <Onboard Audio Interface>
T he board provides the onboard high definition audio with Realtek ALC888
Connector: CN_AUDIO
Type: 10-pin (2 x 5) 1.27mm x 2.54mm-pitch header
Pin Description Pin Description
1 MIC2_L 2 AGND
3 MIC2_R 4 AVCC
5 FP_OUT_R 6 MIC2_JD
7 SENSE_B 8 N/C
9 FP_OUT_L 10 LINE2_JD
24-
-
2 10
CN_AUDIO
1 9
Page 26
LP-172 User’s Manual
2.10 <USB2.0 Interface>
Based on Intel® NM10 FCH, the board provides 4 USB2.0 ports. The USB2.0 interface
provides up to 480Mbps of transferring rate.
Interface USB2.0
Controller NM10
Transfer Rate Up to 480Mb/s
Output Current 500mA
10 9
2 10
1 9
2 1
CN_USB1
CN_USB2
Connector: CN_USB
Type: 10-pin (5 x 2) header for USB Port
Pin Description Pin Description
1 VCC 2 VCC
3 Data0- 4 Data15 Data0+ 6 Data1+
7 Ground 8 Ground
9 Ground 10 N/C
PS: The USB2.0 will be only active when you connecting with the USB2.0 devices, if you
insert an USB1.1 device, the port will be changed to USB1.1 protocol automatically. The
transferring rate of USB2.0 as 480Mbps is depends on device capacity, exact
transferring rate may not be up to 480Mbps.
25-
-
Page 27
LP-172 User’s Manual
2.11 <Serial Port Jumper Setting >
The board provides two RS232 serial ports
Connector: CN_COM1/2
Type: 20-pin (5 x 2) 1.27mm x 2.54mm-pitch header for COM1/2
Pin Description Pin Description
1 MDCD1- 2 MSIN13 MSO1- 4 MDTR15 N/C 6 MDSR17 MRTS1- 8 MCTS19 MRI1- 10 N/C
11 MDCD2- 12 MSIN213 MSO2- 14 MDTR215 GND 16 MDSR217 MRTS2- 18 MCTS219 MRI2- 20 N/C
26-
-
20 19
2 1
Page 28
LP-172 User’s Manual
2.12 <Power & FAN Connector >
The board requires DC input with 2-pin header, the input voltage range is from 5V for the
input current, please take a reference of the power consumption report on appendix.
2.12.1 <Power Input>
Connector: DC_IN
Type: 2-pin header
Pin Description Pin Description
1 Ground 2 +5V
Remark: DC input voltage only +5V
2
1
DC_IN
27-
-
Page 29
LP-172 User’s Manual
2.12.2 <Power Output>
Connector: DC_OUT
Type: 6-pin connector for +5V output
Pin Description Pin Description Pin Description
1 N/C 2 N/C 3 Ground
4 Ground 5 +5V 6 +5V
Note: Maximum output current 5V/1A
1 6
DC_OUT
28-
-
Page 30
LP-172 User’s Manual
2.12.3 <Fan Connector>
Connector: SYSFAN
Type: 3-pin fan wafer connector
Connector model: 2001-WS-03-LF
Pin Description Pin Description Pin Description
1 Ground 2 +5V 3 CSFAN
Connector: CPUFAN
Type: 3-pin fan wafer connector
Connector model: 2001-WS-03-LF
Pin Description
1 Ground
2 +5V
3 P1FAN
CPUFAN
3
1
SYSFAN
3
1
29-
-
Page 31
LP-172 User’s Manual
2.13 <Indicator and Switch>
The JFRNT provides front control panel of the board, such as power button, reset and
beeper, etc. Please check well before you connecting the cables on the chassis.
Connector: JFRNT
Type: onboard 10-pin (2 x 5) 2.54-pitch header
Function Signal PIN Signal
10
2
Power LED
JFRNT
Power
Speaker
HDD LED
Reset
9
1
PWRBT- 1 2 PWRBT+
SPK- 3 4 SPK+
HLED- 5 6 HLED+
GND 7 8 PWLED+
Reset- 9 10 GND
30-
-
Page 32
LP-172 User’s Manual
(This Page is Left For Blank)
31-
-
Page 33
LP-172 User’s Manual
Chapter 3 <BIOS Setup>
The motherboard uses the Phoenix BIOS for the system configuration. The
Phoenix BIOS in the single board computer is a customized version of the industrial
standard BIOS for IBM PC AT-compatible computers. It supports Intel® x86 and
compatible CPU architecture based processors and computers. The BIOS provides
critical low-level support for the system central processing, memory and I/O
sub-systems.
The BIOS setup program of the single board computer let the customers modif y the
basic configuration setting. The settings are stored in a dedicated battery-backed
memory, NVRAM, retains the information when the power is turned off. If the battery
runs out of the power, then the settings of BIOS will come back to the default setting.
The BIOS section of the manual is subject to change without notice and is provi ded
here for reference purpose only. The settings and configurations of the BIOS are
current at the time of print, and therefore they may not be exactly the same as that
displayed on your screen.
To activate CMOS Setup program, press ＜DEL＞ key immediately after you turn
on the system. The following message “Press DEL to enter SETUP” should appear in
the lower left hand corner of your screen. When you e nter the CMOS Setup Utility,
the Main Menu will be displayed as Figure 4-1. You can use arrow keys to select
your function, press ＜Enter＞ key to accept the selection and enter the sub-menu.
Figure 4-1 CMOS Setup Utility Main Screen
32-
-
Page 34
LP-172 User’s Manual
(This Page is Left for Blank)
33-
-
Page 35
LP-172 User’s Manual
Appendix A <I/O Port Pin Assignment>
A.1 <SATA Port>
Connector: SATA
Type: 10-pin header for SATA Port
Pin Description Pin Description
1 Ground 2 TXP
3 TXN 4 Ground
5 N/C 6 N/C
7 Ground 8 RXN
9 RXP 10 Ground
A.2 <CRT Port>
Connector: CRT
Type: 15-pin D-sub female connector on rear panel
Pin Description Pin Description Pin Description
1 RED 6 Ground 11 N/C
2 GREEN 7 N/C 12 5VCDA
3 BLUE 8 Ground 13 HSYNC
4 N/C 9 LVGA5V 14 VSYNC
5 -CRTATCH 10 -CRTATCH 15 5VCLK
110
5 1
10 6
15 11
A.3 <LAN Port>
Connector: RJ45
Type: RJ45 connector with LED on rear panel
Pin 1 2 3 4 5 6 7 8
Description TRD0+ TRD0- TRD1+ TRD2+ TRD2- TRD1- TRD3+ TRD3-
34-
-
8 1
Page 36
LP-172 User’s Manual
A.4 <LAN LED Port>
Connector: JSPD1
Type: 2-pin header for LAN Speed LED connector RJ45 connector with LED on
rear panel
When Lan speed 10/100Mbps
Pin Description
1 LED2 LED+
When Lan speed 1Gbps
Pin Description
1 LED+
2 LED-
2
1
Connector: JACT
Type: 5-pin header for LAN Activity LED connector
Pin Description
1 LED2 LED+
2
1
A.5 <LPC Port>
Connector: JSPD1
Type: 10-pin header for LPC Port
Pin Description Pin Description
1 LPC_CLK 2 RESET3 LFRAME- 4 LAD3
5 LAD2 6 LAD1
7 LAD0 8 +3.3V
9 Ground 10 Ground
35-
-
10 9
2 1
Page 37
LP-172 User’s Manual
Appendix B <Flash BIOS>
B.1 BIOS Auto Flash Tool
The board is based on phoenix BIOS and can be updated easily by the BIOS auto
flash tool. You can download the tool online at the address below:
http://www.phoenix.com/en/home/
http://www.commell.com.tw/Support/Support_SBC.htm
File name of the tool is “Pflash.exe”, it’s the utility that can write the data into the
BIOS flash ship and update the BIOS.
B.2 Flash Method
1. Please make a bootable floppy disk.
2. Get the last .bin files you want to update and copy it into the disk.
3. Copy awardflash.exe to the disk.
4. Power on the system and flash the BIOS.
(Example: C:/Pflash /sa /bbl /cvar XXX.bin)
5. Re-star the system.
Any question about the BIOS re-flash please contact your distributors or visit the
web-site at below:
http://www.commell.com.tw/support/support.htm
36-
-
Page 38
LP-172 User’s Manual
Appendix C <System Resources>
C.1 <I/O Port Address Map>
37-
-
Page 39
LP-172 User’s Manual
38-
-
Page 40
LP-172 User’s Manual
C.2 <Memory Address Map>
39-
-
Page 41
LP-172 User’s Manual
C.3 <System IRQ Resources>
40-
-
Page 42
LP-172 User’s Manual
41-
-
Page 43
LP-172 User’s Manual
42-
-
Page 44
LP-172 User’s Manual
Appendix D <Watch Dog timer Setting>
The watchdog timer makes the system auto-reset while it stops to work for a period. The
integrated watchdog timer can be setup as system reset mode by program.
Timeout Value Range
- 1 to 255
- Second or Minute
Program Sample
Watchdog timer setup as system reset with 5 second of timeout
O 2E 87
O 2E 87
O 2E 07
O 2F 08 Logical Device 8
O 2E 30
O 2F 01 Activate
O 2E F5
O 2F 02 Set as Second*
O 2E F6
O 2F 05 Set as 5
* Minute: bit 3 = 1; Second: bit 3 = 0
You can select Timer setting in the BIOS, after setting the time options, the system
will reset according to the period of your selection.
43-
-
Page 45
LP-172 User’s Manual
This Page is Left for Blank)
44-
-
Page 46
LP-172 User’s Manual
Contact Information
Any advice or comment about our products and service, or
anything we can help you please don’t hesitate to contact with us.
We will do our best to support you for your products, projects and
business.
Taiwan Commate Computer Inc.
Address
TEL +886-2-26963909
FAX +886-2-26963911
Website
E-Mail
Facebook
Twitter https://twitter.com/Taiwan_Commate
19F., No.94, Sec. 1, Xintai 5th Rd., Xizhi Dist., New Taipei
City 22102, Taiwan
TUhttp://www.commell.com.twUT
TUinfo@commell.com.twUT (General Information)
TUtech@commell.com.twUT (Technical Support)
https://www.facebook.com/pages/Taiwan-Commate-Computer-Inc/547993955271899
Commell is our trademark of industrial PC division
45-
-
Loading...