Page 1
LP-171
Pico-ITX
User’s Manual
Edition 1.5
2015/06/16
Page 2
LP-171 User’s Manual
-1-
Copyright
Copyright 2009. All rights reserved. This document is copyrighted and all rights are
reserved. The information in this document is subject to change without prior notice to
make improvements to the products.
This document contains proprietary information and protected by copyright. No part of
this document may be reproduced, copied, or translated in any form or any means
without prior written permission of the manufacturer.
All trademarks and/or registered trademarks contains in this document are property of
their respective owners.
Disclaimer
The company shall not be liable for any incidental or consequential damages resulting
from the performance or use of this product.
The company does not issue a warranty of any kind, express or implied, including
without limitation implied warranties of merchantability or fitness for a particular purpose.
The company has the right to revise the manual or include changes in the specifications
of the product described within it at any time without notice and without obligation to
notify any person of such revision or changes.
Trademark
All trademarks are the property of their respective holders.
Any questions please visit our website at TUhttp://www.commell.com.twUT
Page 3
LP-171 User’s Manual
-2-
Dual COM PORT Cable x 1
(OALES-BKU2NB)
Packing List:
Please check the package content before you starting using the board.
Hardware:
LP-171 PICO-ITX“ Miniboard x 1
Cable Kit:
Printed Matters:
Driver CD x 1 (Including User’s Manual)
Audio Cable x 1
(OALPJ-HDUNB)
PS/2 keyboard & mouse Cable x 1
(OALPS2/MK)
USB Cable x 1
(OALUSBA-3)
DC_IN Power Cable x 1
(OALDC-3)
Panel Inverter Cable x 1
(OALINV-5P-L15)
Option:
MPX-SDVOX power Cable x 1
(OAL4PS-6P)
Page 4
LP-171 User’s Manual
-3-
Index
Chapter 1 <Introduction>................................................................................. 5
1.1 <Product Overview>..............................................................................................5
1.2 <Product Specification> ........................................................................................6
1.3 <Mechanical Drawing> .........................................................................................8
1.4 <Block Diagram> ..................................................................................................9
Chapter 2 <Hardware Setup>......................................................................... 10
2.1 <Connector Location>.........................................................................................10
2.2 <Jumper Reference>............................................................................................12
2.3 <Connector Reference>.......................................................................................13
2.3.1 <Internal Connector> ........................................................................13
2.3.2 <External Connector> .......................................................................13
2.4 <CPU and Memory Setup> .................................................................................14
2.5 <CMOS & ATX Setup> ......................................................................................15
2.6 <CF Interface>.....................................................................................................16
2.7 <LAN Interface> .................................................................................................16
2.8 <Onboard Display Interface> ..............................................................................17
2.8.1 <Analog VGA Interface> (LP-171QT only).....................................17
2.8.2 <Digital Display>..............................................................................18
2.8.3 <DVI Interface >(LP-171QD only)...................................................22
2.9 <Onboard Audio Interface>.................................................................................23
2.10 <USB2.0 Interface>...........................................................................................24
2.11 <Serial Port Jumper Setting >............................................................................25
2.12 <Power & FAN Connector >.............................................................................26
2.12.1 <Power Input>.................................................................................26
2.12.2 <Power Output>..............................................................................27
2.12.3 <Fan Connector>.............................................................................28
2.13 <Indicator and Switch>......................................................................................29
Chapter 3 <BIOS Setup> ................................................................................30
Appendix A <I/O Port Pin Assignment> ....................................................... 31
Page 5
LP-171 User’s Manual
-4-
A.1 <LPC Port>......................................................................................................... 31
A.2 < CRT Port >......................................................................................................31
A.3 <LAN Port>........................................................................................................31
Appendix B <Flash BIOS>..............................................................................32
B.1 BIOS Auto Flash Tool.........................................................................................32
B.2 Flash Method ......................................................................................................32
Appendix C <System Resources> ................................................................33
C.1 <I/O Port Address Map>.....................................................................................33
C.2 <Memory Address Map >................................................................................... 35
C.3 < System IRQ Resources >.................................................................................36
Appendix E <Watch Dog timer Setting > ......................................................37
Contact Information........................................................................................38
Page 6
LP-171 User’s Manual
-5-
Chapter 1 <Introduction>
1.1 <Product Overview>
LP-171 is the PICO-ITX miniboard, with Intel® Atom Z510P processor for 400 MHz front
side bus, Intel® US15WP SCH, integrated GMA500 graphics, DDR2 SO-DIMM memory,
Realtek HD Audio, CF and one Intel® 82574L Gigabit LAN.
Intel® Atom Processor
The Intel® Atom Z510P single core processor is with 400 MHz front side bus,512KB L2
cache. It's built on 45nm process technology support Hyper-Threading Technology,
Enhanced Intel® SpeedStep® Technology reduces average system power
consumption.
Embedded Intel® SCH
The board integrates Intel® US15WP SCH. The chipset features power-efficient
graphics with an integrated 32-bit 3D graphics engine based on Intel® Graphics Media
Accelerator 500 architecture with DVI, LVDS, CRT display ports. It provides I/O
capabilities and flexibility via high-bandwidth interfaces such as PCIE and Hi-Speed
USB 2.0 connectivity. It also includes a single channel for 400 MHz DDR2 system
memory (SODIMM), HD Audio.
Page 7
LP-171 User’s Manual
-6-
1.2 <Product Specification>
General Specification
Form Factor
PICO-ITX miniboard
CPU
Intel® Atom™ Z510P processor 1.1GHz
Package type: 437pin FCBGA8 with an IHS,
Front side bus: 400MHz
Memory
1 x 200-pin DDR2 SO-DIMM SDRAM up to 2GB
Unbufferred, none-ECC memory supported only
*Memory chip with width x16 bits is strongly recommended!
Chipset
Intel® SCH US15WP
BIOS
Phoenix-Award v6.00PG 8Mb SPI flash BIOS
Green Function
Power saving mode includes doze, standby and suspend modes.
ACPI version 1.0 and APM version 1.2 compliant
Watchdog Timer
System reset programmable watchdog timer with 1 ~ 255
sec./min. of timeout value
Real Time Clock
Intel® SCH built-in RTC with lithium battery
Enhanced IDE
One CompactFlash Type II socket on solder side
Multi-I/O Port
Chipset
Intel® SCH with Winbond® W83627DHG controller
Serial Port
Two RS-232 serial port
USB Port
Two internal Hi-Speed USB 2.0 ports with 480Mbps of transfer
rate
K/B & Mouse
PS/2 keyboard and mouse port
VGA Display Interface
Chipset
Intel® US15WP SCH (System Controller Hub)
Frame Buffer
Up to 256MB shared with system memory
Display Type
CRT, LCD monitor with analog display (LP-171QT only),
DVI (LP-171QD only)
Connector
External DB15 female connector (LP-171QT only)
External DVI connector (LP-171QD only)
Onboard 20-Pin LVDS and 5-Pin inverter connector
Ethernet Interface
Controller
1 x Intel® 82574L Gigabit Ethernet controller
Type
Triple speed 10/100/1000Base-T
auto-switching Fast Ethernet
Full duplex, IEEE802.3U compliant
Connector
1 X External RJ45 connector with LED
Page 8
LP-171 User’s Manual
-7-
Audio Interface
Chipset
REALTEK ALC888
Interface
Stereo audio Line-out and MIC-in
Connector
Onboard audio connector with pin header
Expansive Interface
PCIE mini card
1 x PCIE mini card socket
Power and Environment
Power
Requirement
DC 12V input with onboard 2-pin connector
Dimension
100 (L) x 72(H) mm
Temperature
Operating within 0 ~ 60℃
Storage within -20 ~ 85℃
Ordering Code
LP-171QT
Support Intel® Atom Z510P processor with onboard VGA, LVDS,
Audio, Giga LAN, USB2.0, CF , PCIE mini card
LP-171QD
Same as LP-171QT but without VGA, support DVI
LP-171QX
Same as LP-171QT but without VGA,
support 24bit dual channel LVDS by MPX-SDVOX
( Note : Onboard MIni-PCIe socket support MPX-SDVOX
only )
The specifications may be different as the actual production.
For further product information please visit the website at TUhttp://www.commell.com.twUT
Page 9
LP-171 User’s Manual
-8-
1.3 <Mechanical Drawing>
Unit: inch
Page 10
LP-171 User’s Manual
-9-
W83627DHG
CRT / DVI
DDR2 SODIMM 2GB max.
PS2 KB/MS
RS232
LPC
PCIE Giga LAN
Compact Flash
USB port
HD Audio
PCIE mini card socket
1.4 <Block Diagram>
24bit Single Channel LVDS
Page 11
LP-171 User’s Manual
-10-
CN_LPC
CN_AUDIO
CN_USB1
Chapter 2 <Hardware Setup>
2.1 <Connector Location>
CN_COM1/2
FAN
CN_LVDS
JFRNT
DC_IN
MINI_CARD
CN_INV
DC_OUT
Page 12
LP-171 User’s Manual
-11-
RJ45 PS2 CRT
DVI
DDRII
CF
LP-171QT
LP-171QD
LP-171QX
Page 13
LP-171 User’s Manual
-12-
JAT
2.2 <Jumper Reference>
Jumper
Function
JRTC
CMOS Operating/Clear Setting
JVLCD
LCD Panel Voltage Setting
JAT
AT/ATX Mode Setting
JRTC
JVLCD
Page 14
LP-171 User’s Manual
-13-
2.3 <Connector Reference>
2.3.1 <Internal Connector>
Connector
Function
Remark
DDRII
200 -pin DDR2 SO-DIMM SDRAM slot
Standard
CF
Compact Flash Type II socket
Standard
MINI_CARD
PCIE mini card socket
Standard
CN_LVDS
10 x 2-pin LVDS connector
Standard
CN_INV
5-pin LCD inverter connector
Standard
CN_USB
5 x 2-pin USB connector
Standard
CN_AUDIO
5 x 2-pin audio connector
Slim
CN_COM1/2
10 x 2-pin com connector
Slim
JFRNT
8-pin switch/indicator connector
Standard
FAN
3-pin system cooler fan connector
Standard
DC_OUT
6-pin power output connector
Standard
DC_IN
DC input connector
Standard
2.3.2 <External Connector>
Connector
Function
Remark
CRT
DB15 VGA connector
Standard
DVI
Type DVI connector
Standard
PS2
PS/2 keyboard and mouse connector
Standard
RJ45
RJ45 LAN connector
Standard
Page 15
LP-171 User’s Manual
-14-
2.4 <CPU and Memory Setup>
The board provides one 200-pin DDR2 SO-DIMM to support DDR2 400 memory
modules up to 2GB of capacity. Non-ECC, unbuffered memory is supported only.
*Memory chip with width x16 bits is strongly recommended!
DDRII
Page 16
LP-171 User’s Manual
-15-
2.5 <CMOS & ATX Setup>
The board’s data of CMOS can be setting in BIOS. If the board refuses to boot due to
inappropriate CMOS settings, here is how to proceed to clear (reset) the CMOS to its
default values.
Jumper: JRTC
Type: Onboard 3-pin jumper
JRTC
Mode
1-2
Clear CMOS
2-3
Normal Operation
Default setting
Jumper: JAT
Type: onboard 3-pin jumper
JAT
Mode
1-2
AT Mode
2-3
ATX Mode
Default setting
JAT
JRTC
1
3
1
3
Page 17
LP-171 User’s Manual
-16-
2.6 <CF Interface>
The board has one Compact Flash Type II socket on the solder side.
2.7 <LAN Interface>
The Intel® 82574L supports triple speed of 10/100/1000Base-T, with IEEE802.3
compliance.
CF
LAN
Page 18
LP-171 User’s Manual
-17-
2.8 <Onboard Display Interface>
Based on Intel® SCH chipset with built-in GMA (Graphic Media Accelerator) 500
graphics, the board provides one DB15 or DVI connector on real external I/O port,
and one 20-pin LVDS interface with 5-pin LCD backlight inverter connector. The board
provides dual display function with clone mode and extended desktop mode for CRT,
DVI and LVDS.
2.8.1 <Analog VGA Interface> (LP-171QT only)
Please connect your CRT or LCD monitor with DB15 male connector to the onboard
DB15 female connector on rear I/O port.
The board supports up to 1920 x 1080 (WUXGA) of resolution.
CRT
Page 19
LP-171 User’s Manual
-18-
19
20
1
2
2.8.2 <Digital Display>
The board provides one 20-pin LVDS connector for 18 or 24 bit single channel panels,
supports up to 1920 x 1080 (WUXGA) of resolution, with one LCD backlight inverter
connector and one jumper for panel voltage setting
CN_INV
CN_LVDS
1 5
JVLCD
Page 20
LP-171 User’s Manual
-19-
Connector: CN_INV Jumper: JVLCD
Type: 5-pin Inverter power connector Type: 3-pin Power select jumper
Connector model: molex_53261-5pin
Pin
Description
Pin
Description
1
+12V
1-2
+5V
2
GND
2-3
+3.3V
3
GND
Default: 2-3
4
GND
5
ENABKL
Connector: CN_LVDS
Type: onboard 20-pin connector for LVDS connector
Connector model: HIROSE DF13-20DP-1.25V
Pin
Signal
Pin
Signal
2
LCDVCC
1
LCDVCC
4
GND3GND
6
TXL0P
5
TXL0N
8
TXL1N
7
GND
10
GND9TXL1P
12
TXL2P
11
TXL2N
14
TXLCKN
13
GND
16
GND15TXLCKP
18
TXL3P
17
TXL3N
20
GND19GND
Page 21
LP-171 User’s Manual
-20-
To setup the LCD, you need the component below:
1. A panel with LVDS interfaces.
2. An inverter for panel’s backlight power.
3. A LCD cable and an inverter cable.
For the cables, please follow the pin assignment of the connector to make a cable, because
every panel has its own pin assignment, so we do not provide a standard cable; please find
a local cable manufacture to make cables.
LCD Installation Guide:
1. Preparing the LP-171, LCD panel and the backlight inverter
2. Please check the datasheet of the panel to see the voltage of
the panel, and set the jumper JVLCD to +5V or +3.3V.
3. You would need a LVDS type cable.
4. To connect all of the devices well.
For sample illustrator only
Panel side
Board side
Page 22
LP-171 User’s Manual
-21-
After setup the devices well, you need to select the LCD panel type in the
BIOS.
The panel type mapping is list below:
LP-171 BIOS panel type selection form
On board Single channel LVDS
18bit
24bit
NO.
Output format
NO.
Output format
1
640 x 480
9
640 x 480
2
800 x 480
10
800 x 480
3
800 x 600
11
800 x 600
4
1024 x 600
12
1024 x 768
5
1024 x 768
13
1280 x 720
6
1280 x 768
14
1280 x 768
7
1280 x 800
15
1366 x 768
8
1400 x 1050
LP-171X BIOS panel type selection form
MPX-SDVOX Dual channel LVDS
Output format
1
1280 x 1024 24bit
The LP-171X series supports dual channel 24bit LVDS, if need support other
resolution flat panel, please contact Commell tech support team for customize
BIOS and driver.
Page 23
LP-171 User’s Manual
-22-
DVI
2.8.3 <DVI Interface >(LP-171QD only)
The board also comes with a DVI interface with Chrontel CH7307C for digital video
interface. Supports up to 1600 x 1200 (UXGA) of resolution.
Connector: DVI
Connector type: 19-pin Type A DVI connector
Pin Number
Assignment
Pin Number
Assignment
1
TMDS_D2+
2
Ground
3
TMDS_D2-
4
TMDS_D1+
5
Ground
6
TMDS_D1-
7
TMDS_D0+
8
Ground
9
TMDS_D0-
10
TMDS_CLK+
11
Ground
12
TMDS_CLK-
13
N/C14N/C
15
DVI_SCL
16
DVI_SDA
17
Ground
18
PVDD
19
HPDET
Page 24
LP-171 User’s Manual
-23-
CN_AUDIO
2 1
2.9 <Onboard Audio Interface>
The board provides the onboard high definition audio with Realtek ALC888
Connector: CN_AUDIO
Type: 10-pin (2 x 5) 1.27mm x 2.54mm-pitch header
Pin
Description
Pin
Description
1
MIC_L
2
Ground
3
MIC_R
4
AVCC
5
FRO_R
6
MIC_JD
7
SENSE
8
N/C
9
SPK_L
10
LINE2_JD
10 9
Page 25
LP-171 User’s Manual
-24-
CN_USB
2.10 <USB2.0 Interface>
Based on Intel® SCH, the board provides 2 USB2.0 ports. The USB2.0 interface
provides up to 480Mbps of transferring rate.
Interface
USB2.0
Controller
US15WP
Transfer Rate
Up to 480Mb/s
Output Current
500mA
Connector: CN_USB
Type: 10-pin (5 x 2) header for USB Port
Pin
Description
Pin
Description
1
VCC2VCC
3
Data0-
4
Data15
Data0+
6
Data1+
7
Ground
8
Ground
9
Ground
10
N/C
9 1
10 2
Page 26
LP-171 User’s Manual
-25-
2.11 <Serial Port Jumper Setting >
The board provides two RS232 serial ports,
Connector: CN_COM1/2
Type: 20-pin (5 x 2) 1.27mm x 2.54mm-pitch header for COM1/2
Pin
Description
Pin
Description
1
MDCD1
2
MSIN1
3
MSO1
4
MDTR1
5
GND6MDSR1
7
MRTS1
8
MCTS1
9
MRI1
10
NC
11
MDCD2
12
MSIN2
13
MSO2
14
MDTR2
15
GND16MDSR2
17
MRTS2
18
MCTS2
19
MRI2
20
NC
19 1
20 2
CN_COM1/2
Page 27
LP-171 User’s Manual
-26-
2.12 <Power & FAN Connector >
The board requires DC input with 2-pin header, the input voltage is 12V, for the input
current, please take a reference of the power consumption report on appendix.
2.12.1 <Power Input>
Connector: DC_IN
Type: 2-pin header
Pin
Description
Pin
Description
1
Ground
2
+12V
1
DC_IN
2
Page 28
LP-171 User’s Manual
-27-
2.12.2 <Power Output>
Connector: DC_OUT
Type: 6-pin connector for +5V/+12V output
Pin
Description
1
+12V
2
+12V
3
GND
4
GND
5
+5V
6
+5V
Note: Maximum output current 12V/1A, 5V/1A
DC_OUT
1
6
Page 29
LP-171 User’s Manual
-28-
2.12.3 <Fan Connector>
Connector: SYSFAN, CPUFAN
Type: 3-pin fan wafer connector
Pin
Description
Pin
Description
Pin
Description
1
Ground
2
+12V
3
Speed detect
FAN
1
3
Page 30
LP-171 User’s Manual
-29-
2.13 <Indicator and Switch>
The JFRNT provides front control panel of the board, such as power button, reset, etc.
Please check well before you connecting the cables on the chassis.
Connector: JFRNT
Type: onboard 8-pin (1 x 8) 2.54-pitch header
Function
Signal
PIN
Reset+
8
Reset
Reset-
7
PWRLED-
6
Power LED
PWRLED+
5
HDLED-
4
HDD LED
HDLED+
3
PWRBT-
2
Power
PWRBT+
1
(This Page is Left For Blank)
1
JFRNT
8
Page 31
LP-171 User’s Manual
-30-
Chapter 3 <BIOS Setup>
The motherboard uses the Award BIOS for the system configuration. The Award
BIOS in the single board computer is a customized version of the industrial standard
BIOS for IBM PC AT-compatible computers. It supports Intel® x86 and compatible
CPU architecture based processors and computers. The BIOS provides critical
low-level support for the system central processing, memory and I/O sub-systems.
The BIOS setup program of the single board computer let the customers modify the
basic configuration setting. The settings are stored in a dedicated battery-backed
memory, NVRAM, retains the information when the power is turned off. If the battery
runs out of the power, then the settings of BIOS will come back to the default setting.
The BIOS section of the manual is subject to change without notice and is provided
here for reference purpose only. The settings and configurations of the BIOS are
current at the time of print, and therefore they may not be exactly the same as that
displayed on your screen.
To activate CMOS Setup program, press ＜DEL＞ key immediately after you turn
on the system. The following message “Press DEL to enter SETUP” should appear in
the lower left hand corner of your screen. When you enter the CMOS Setup Utility,
the Main Menu will be displayed as Figure 4-1. You can use arrow keys to select
your function, press ＜Enter＞ key to accept the selection and enter the sub-menu.
Figure 4-1 CMOS Setup Utility Main Screen
Page 32
LP-171 User’s Manual
-31-
Appendix A <I/O Port Pin Assignment>
A.1 <LPC Port>
Connector: CN_LPC
Type: 10-pin header for LPC Port
Pin
Description
Pin
Description
1
LPC_CLK
2
RESET3
LFRAME-
4
LAD3
5
LAD2
6
LAD1
7
LAD1
8
+3.3V
9
Ground
10
Ground
A.2 < CRT Port >
Connector: CRT
Type: 15-pin D-sub female connector on rear panel
Pin
Description
Pin
Description
Pin
Description
1
RED6Ground
11
N/C
2
GREEN
7
Ground
12
5VCDA
3
BLUE
8
Ground
13
HSYNC
4
N/C9LVGA5V
14
VSYNC
5
Ground
10
Ground
15
5VCLK
A.3 <LAN Port>
Connector: RJ45
Type: RJ45 connector with LED on rear panel
Pin12345678
Description
TRD0+
TRD0-
TRD1+
TRD2+
TRD2-
TRD1-
TRD3+
TRD3-
2
10
5 1
15 11
10 6
8 1
9
1
Page 33
LP-171 User’s Manual
-32-
Appendix B <Flash BIOS>
B.1 BIOS Auto Flash Tool
The board is based on Award BIOS and can be updated easily by the BIOS auto
flash tool. You can download the tool online at the address below:
TUhttp://www.award.comUT
TUhttp://www.commell.com.tw/support/support.htmUT
File name of the tool is “awdflash.exe”, it’s the utility that can write the data into the
BIOS flash ship and update the BIOS.
B.2 Flash Method
1. Please make a bootable floppy disk.
2. Get the last .bin files you want to update and copy it into the disk.
3. Copy awardflash.exe to the disk.
4. Power on the system and flash the BIOS. (Example: C:/ awardflash XXX.bin)
5. Re-star the system.
Any question about the BIOS re-flash please contact your distributors or visit the
web-site at below:
http://www.commell.com.tw/support/support.htm
Page 34
LP-171 User’s Manual
-33-
Appendix C <System Resources>
C.1 <I/O Port Address Map>
Page 35
LP-171 User’s Manual
-34-
Page 36
LP-171 User’s Manual
-35-
C.2 <Memory Address Map >
Page 37
LP-171 User’s Manual
-36-
C.3 < System IRQ Resources >
Page 38
LP-171 User’s Manual
-37-
Appendix E <Watch Dog timer Setting >
The watchdog timer makes the system auto-reset while it stops to work for a period. The
integrated watchdog timer can be setup as system reset mode by program.
Timeout Value Range
- 1 to 255
- Second or Minute
Program Sample
Watchdog timer setup as system reset with 5 second of timeout
2E, 87
2E, 87
2E, 07
2F, 08
Logical Device 8
2E, 30
2F, 01
Activate
2E, F5
2F, 00
Set as Second*
2E, F6
2F, 05
Set as 5
* Minute: bit 3 = 1; Second: bit 3 = 0
You can select Timer setting in the BIOS, after setting the time options, the system
will reset according to the period of your selection.
(This Page is Left for Blank)
Page 39
LP-171 User’s Manual
-38-
Contact Information
Any advice or comment about our products and service, or
anything we can help you please don’t hesitate to contact with us.
We will do our best to support you for your products, projects and
business.
Taiwan Commate Computer Inc.
Address
19F, No. 94, Sec. 1, Xintai 5th Rd., Xizhi Dist
New Taipei City, Taiwan
TEL
+886-2-26963909
FAX
+886-2-26963911
Website
TUhttp://www.commell.com.twUT
E-Mail
TUinfo@commell.com.twUT (General Information)
TUtech@commell.com.twUT (Technical Support)
Facebook
https://www.facebook.com/pages/Taiwan-Commate-Computer-Inc/547993955271899
Twitter
https://twitter.com/Taiwan_Commate
Commell is our trademark of industrial PC division
Loading...