COMMELL LP-170 User Manual

Page 1
LP-170
Pico-ITX
User’s Manual
Edition 2.0
2013/7/29
Page 2
Page 3
Copyright
Copyright 2009. All rights reserved. This document is copyrighted and all rights are reserved. The information in this document is subject to change without prior notice to make improvements to the products. This document contains proprietary information and pr otected by copyright. No part of this document may be reproduced, copied, or translated in any form or any means without prior written permission of the manufacturer. All trademarks and/or registered trademarks contains in this document are propert y of their respective owners.
Disclaimer
The company shall not be liable for any incidental or consequential damages resulting from the performance or use of this product. The company does not issue a warranty of any kind, express or implied, including without limitation implied warranties of merchantability or fitness for a particular purpose. The company has the right to revise the manual or include changes in the specifications of the product described within it at any time without notice and without obligation to notify any person of such revision or changes.
Trademark
All trademarks are the property of their respective holders.
Any questions please visit our website at TUhttp://www.commell.com.twUT
-1-
Page 4
(
)
(
)
(
)
Packing List:
Please check the package content before you starting using the board.
Hardware:
LP-170 “PICO-ITX Miniboard” x 1
Cable Kit:
DC_IN Power Cable x 1
OALDC-3
SATA Cable x 1
(OALSATA-L)
USB Cable x 1
(OALUSBA-3)
PS/2 Keyboard & Mouse Cable x 1
(OALPS2/MK)
DC_OUT Power Cable x 1
(OALS1P1-6P-L20)
Option:
SATA Cable x 1
OALSATA-L
Audio Cable x 1
(OALPJ-HDUNB)
Dual COM PORT cable x 1
(OALES-BKU2NB)
LP-170G/H/A/C Heatsink
with Fan x 1
(OHS-170)
Pennal Inverter Cable x 1
OALINV-5P-L15
Printed Matters:
Driver CD x 1 (Including User’s Manual)
-2-
Page 5
Index
Chapter 1 <Introduction>................................................................................. 5
1.1 <Product Overview>.................................................................................. 5
1.2 <Product Specification>.............................................................................6
1.3 <Mechanical Drawing>.............................................................................. 8
1.4 <Block Diagram>.......................................................................................9
Chapter 2 <Hardware Setup>.........................................................................10
2.1 <Connector Location>.............................................................................10
2.2 <Jumper Reference>............................................................................... 12
2.3 <Connector Reference>..........................................................................13
2.3.1 <Internal Connector>..............................................................13
2.3.2 <External Connector> ............................................................13
2.4 <CPU and Memory Setup> .....................................................................14
2.5 <CMOS & ATX Setup>............................................................................15
2.6 <CF Interface>.........................................................................................16
2.7 <Serial ATA Interface>............................................................................17
2.8 <LAN Interface> ......................................................................................17
2.9 <Onboard Display Interface> ..................................................................18
2.9.1 <Analog VGA Interface> ........................................................18
2.9.2 <Digital Display>.....................................................................19
2.10 <Onboard Audio Interface>...................................................................23
2.11 <USB2.0 Interface>...............................................................................24
2.12 <Serial Port Jumper Setting > ...............................................................25
2.13 <Power & FAN Connector >..................................................................26
2.13.1 <Power Input>......................................................................26
2.13.2 <Power Output>................................................................... 27
2.13.3 <Fan Connector> .................................................................28
2.14 <Indicator and Switch>..........................................................................29
Chapter 3 <BIOS Setup>................................................................................ 30
Appendix A <I/O Port Pin Assignment> ....................................................... 31
-3-
Page 6
A.1 <LPC Port>..............................................................................................31
A.2 < CRT Port >...........................................................................................31
A.3 <LAN Port>..............................................................................................31
Appendix B <Flash BIOS>..............................................................................32
B.1 BIOS Auto Flash Tool..............................................................................32
B.2 Flash Method...........................................................................................32
Appendix C <System Resources> ................................................................33
C.1 <I/O Port Address Map> (LP-170G)........................................................33
C.2 <Memory Address Map > (LP-170G)......................................................35
C.3 < System IRQ Resources > (LP-170G) ..................................................36
Appendix E <Watch Dog timer Setting >......................................................37
Contact Information........................................................................................38
-4-
Page 7
Chapter 1 <Introduction>
1.1 <Product Overview>
LP-170G /H /A /C is the PICO-ITX miniboard, with Intel® Atom N450 /D410 /D510 /D525 processor, integrated GMA3150 graphics, Intel® ICH8-M, DDR2 SO-DIMM memory, Realtek HD Audio, CF, SATAII and Intel® 82583V Gigabit LAN.
Intel® Atom Processor
The Intel® Atom N450 (D410 /D510 /D525) processor supports one channel of 667 (667/800)MHz DDR2 SDRAM. The chipset features power-efficient graphics with an integrated 18-bit 3D graphics engine based on Intel® Graphics Media Accelerator 3150 architecture with LVDS, CRT display ports. The DMI is designed into the Pineview-M(D) processor to provide an efficient high-bandwidth communication channel between the processor and the ICH8M.
Embedded Intel® ICH8-M
The board integrates Intel® ICH8M. It provides I/O capabilities and flexibility via high-bandwidth interfaces such as PCIE and Hi-Speed USB 2.0 connectivity. Serial ATA. HD Audio.
Flexible Extension Interface
The board also provides Compact Flash Type II socket and one PCIE mini card socket.
-5-
Page 8
1.2 <Product Specification>
General Specification
Form Factor PICO-ITX miniboard CPU Intel® Atom N450 processor 1.66GHz (LP-170G)
Intel® Atom D410 processor 1.66GHz (LP-170H) Intel® Atom D510 processor 1.66GHz (LP-170A) Intel® Atom D525 processor 1.8GHz (LP-170C) Package type: FCBGA559
Memory 1 x 200-pin DDR2 SO-DIMM 667MHz SDRAM up to 2GB
(LP-170G Only)
1 x 200-pin DDR2 SO-DIMM 667MHz SDRAM up to 4GB
(LP-170H/ A/ C Only)
Unbufferred, none-ECC memory supported only Chipset Intel® ICH8M BIOS Phoenix-Award v6.00PG 8Mb SPI flash BIOS Green Function Power saving mode includes doze, standby and suspend modes.
ACPI version 1.0 and APM version 1.2 compliant Watchdog Timer System reset programmable watchdog timer with 1 ~ 255
sec./min. of timeout value Real Time Clock Intel® ICH8-M built-in RTC with lithium battery Enhanced IDE One CompactFlash Type II socket on solder side
Serial ATA Intel® ICH8M integrates 1 Serial ATAII interfaces
(No RAID Function)
Up to 300MB/s of transfer rate
Multi-I/O Port
Chipset Intel® SCH with Winbond® W83627DHG controller Serial Port Two RS-232 serial port USB Port Four internal Hi-Speed USB 2.0 ports with 480Mbps of transfer
rate K/B & Mouse PS/2 keyboard and mouse port
VGA Display Interface
Chipset Intel® Atom N450 processor (System Controller Hub) (LP-170G)
Intel® Atom D410 processor (System Controller Hub) (LP-170H)
Intel® Atom D510 processor (System Controller Hub) (LP-170A)
Intel® Atom D525 processor (System Controller Hub) (LP-170C) Frame Buffer Up to 384MB shared with system memory Display Type CRT, LCD monitor with analog display, LVDS Connector External DB 15 female connector
Onboard 20-Pin LVDS and 5-Pin inverter connector
-6-
Page 9
Ethernet Interface
Controller 1 x Intel® 82583V Gigabit Ethernet controller Type Triple speed 10/100/1000Base-T
auto-switching Fast Ethernet Full duplex, IEEE802.3U compliant
Connector 1 X External RJ 45 connector with LED
Audio Interface
Chipset REALTEK ALC888 Interface Stereo audio Line-out and MIC-in
Connector Onboard audio connector with pin header
Expansive Interface
PCIE mini card 1 x PCIE mini card socket
Power and Environment
Power Requirement Dimension 100 (L) x 72(H) mm Temperature Operating within 0 ~ 60
Ordering Code
LP-170G Support Intel® Atom N450 processor with onboard VGA,
DC 12V input with onboard 2-pin connector
Storage within -20 ~ 85
LVDS for 18bit, Audio, Giga LAN, USB2.0, CF, PCIE mini card
LP-170H Support Intel® Atom D410 processor with onboard VGA,
LVDS for 18bit, Audio, Giga LAN, USB2.0, CF, PCIE mini card
LP-170A Support Intel® Atom D510 processor with onboard VGA,
LVDS for 18bit, Audio, Giga LAN, USB2.0, CF, PCIE mini card
LP-170C Support Intel® Atom D525 processor with onboard VGA,
LVDS for 18bit, Audio, Giga LAN, USB2.0, CF, PCIE mini card
The specifications may be different as the actual production. For further product information please visit the website at
TUhttp://www.commell.com.twUT
-7-
Page 10
1.3 <Mechanical Drawing>
Unit: inch
8-
-
Page 11
1.4 <Block Diagram>
CRT
18bit Single Channel LVDS
Serial A TA II
Intel® Atom
N450 / D410/ D510 / D525
DDR2 SODIMM 2GB max (170G) DDR2 SODIMM 4GB max (170H/ A/ C)
PCIE mini card socket
BIOS
W83627DHG
PS2 KB/MS
RS232
LPC
ICH8M
USB port
Compact Flash
ALC888 HD Audio
PCIE Giga LAN
9-
-
Page 12
Chapter 2 <Hardware Setup>
2.1 <Connector Location>
DC_IN
FAN
JFRNT
CN_LVDS
MINI_CARD
CN_USB2
SATA
CN_LPC
CN_USB1
CN_COM1/2
CN_AUDIO
10-
-
Page 13
CF
DDRII
DC_OUT
LP-170G/ H/ A/ C
RJ45 PS2 CRT
CN_INV
11-
-
Page 14
2.2 <Jumper Reference>
Jumper Function
JRTC CMOS Operating/Clear Setting JVLCD LCD Panel Voltage Setting JAT AT/ATX Mode Setting
JVLCD
JAT
JRTC
12-
-
Page 15
2.3 <Connector Reference>
2.3.1 <Internal Connector>
Connector Function Remark
DDRII 200 -pin DDR2 SO-DIMM SDRAM slot Standard SATA1 7-pin Serial ATA connector Standard CF Compact Flash Type II socket Standard MINI_CARD PCIE mini card socket Standard CN_LVDS 10 x 2-pin LVDS connector Standard CN_INV 5-pin LCD inverter connector Standard CN_USB1/2 5 x 2-pin USB connector Standard CN_AUDIO 5 x 2-pin audio connector Slim CN_COM1/2 10 x 2-pin com connector Slim JFRNT 10-pin switch/indicator connector Standard FAN 3-pin system cooler fan connector Standard DC_OUT 6-pin power output connector Standard DC_IN DC input connector Standard
2.3.2 <External Connector>
Connector Function Remark
CRT DB15 VGA connector Standard PS2 PS/2 keyboard and mouse connector Standard RJ45 RJ45 LAN connector Standard
13-
-
Page 16
2.4 <CPU and Memory Setup>
Non-ECC, unbuffered memory is supported only. LP-170G provides one 200-pin DDR2 SO-DIMM to support DDR2 667 memory modules support up to 2GB of capacity.
Suggestion:
DDR2 SO-DIMM Modules:Raw Card A = 2 Ranks of x16 SDRAMs (Double-sided) Raw Card C = 1 Rank of x16 SDRAMs (Single-sided)
LP-170H/ A/ C provides one 200-pin DDR2 SO-DIMM to support DDR2 667 memory modules support up to 4GB of capacity.
Suggestion:
DDR2 SO-DIMM Modules:Raw Card C = 1 Rank of x16 SDRAMs (Single -sided) Raw Card D = 1 Rank of x8 SDRAMs (Single-sided) Raw Card E = 2 Ranks of x8 SDRAMs (Double -sided)
DDRII
14-
-
Page 17
2.5 <CMOS & ATX Setup>
The board’s data of CMOS can be setting in BIOS. If the board refuses to boot due to inappropriate CMOS settings, here is how to proceed to clear (reset) the CMOS to its default values.
Jumper: JRTC Type: Onboard 3-pin jumper
JRTC Mode
1-2 Clear CMOS 2-3 Normal Operation
Default setting
Jumper: JAT Type: onboard 3-pin jumper
JAT Mode
1-2 AT Mode 2-3 ATX Mode
Default setting
AT: auto-power-on
ATX: no auto-power-on
JAT
3
1
JRTC
3
1
15-
-
Page 18
2.6 <CF Interface>
The board has one Compact Flash Type II socket on the solder side.
CF
16-
-
Page 19
2.7 <Serial ATA Interface>
Based on Intel ICH8M, the board provides one Serial ATAII interfaces with up to 300MB/s of transfer rate.
SATA
2.8 <LAN Interface>
The Intel® 82583v supports triple speed of 10/100/1000Base-T, with IEEE802.3 compliance.
LAN
17-
-
Page 20
2.9 <Onboard Display Interface>
Based on Intel® Atom N450 with built-in GMA (Graphic Media Accelerator) 3150 graphics, the board provides one DB15 on real external I/O port, and one 20-pin LVDS interface with 5-pin LCD backlight inverter connector. The board provides dual display function with clone mode and extended desktop mode for CRT and LVDS.
2.9.1 <Analog VGA Interface>
Please connect your CRT or LCD monitor with DB15 male connector to the onboard DB15 female connector on rear I/O port. LP-170G supports 1400 x 1050 (WUXGA) resolution displays. LP-170H/ A / C supports 2048 x 1536 (WUXGA) resolution displays.
CRT
18-
-
Page 21
2.9.2 <Digital Display>
The board provides one 20-pin LVDS connector for 18 bit single channel panels, LP-170G supports 1280 x 800 (WUXGA) resolution displays. LP-170H/ A/ C supports 1366 x 768 (WUXGA) resolution displays, with one LCD backlight inverter connector and one jumper for panel voltage setting
JVLCD
CN_LVDS
20 19
2 1
5 1
CN_INV
19-
-
Page 22
Connector: CN_INV Type: 5-pin Inverter power connector Connector model: molex_53261-5pin or compatible
Pin Description
1 +12V 2 GND 3 GND 4 GND 5 ENABKL
Jumper: JVLCD Type: 3-pin Power select jumper
Pin Description
1-2 +5V 2-3 +3.3V
Default: 2-3
Connector: CN_LVDS Type: onboard 20-pin connector for LVDS connector Connector model: HIROSE DF13-20DP-1.25V or compatible
Pin Signal Pin Signal
2 LCDVCC 1 LCDVCC 4 GND 3 GND 6 TXL0P 5 TXL0N
8 TXL1N 7 GND 10 GND 9 TXL1P 12 TXL2P 11 TXL2N 14 TXLCKN 13 GND 16 GND 15 TXLCKP 18 SMBDATA 17 SMBCLK 20 GND 19 GND
20-
-
Page 23
To setup the LCD, you need the component below:
1. A panel with LVDS interfaces.
2. An inverter for panel’s backlight power.
3. A LCD cable and an inverter cable.
For the cables, please follow the pin assignment of the connector to make a c able, becaus e every panel has its own pin assignment, so we do not provide a standard cable; ple ase fin d a local cable manufacture to make cables.
LCD Installation Guide:
1. Preparing the LP-170, LCD panel and the backlight inverter
2. Please check the datasheet of the panel to see the voltage of the panel, and set the jumper JVLCD to +5V or +3.3V.
3. You would need a LVDS type cable.
Panel side
4.
To
For sample illustrator only
connect all of the devices well.
21-
-
Board side
Page 24
After setup the devices well, you need to select the LCD panel type in the BIOS.
The panel type mapping is list below:
LP-170 BIOS panel type selection form
On board Single channel LVDS
18bit
NO. Output format
1 640 x 480 2 800 x 480 3 800 x 600 4 1024 x 600 5 1024 x 768 6 1280 x 768
22-
-
Page 25
2.10 <Onboard Audio Interface>
T he board provides the onboard high definition audio with Realtek ALC888
Connector: CN_AUDIO
Type: 10-pin (2 x 5) 1.27mm x 2.54mm-pitch header
Pin Description Pin Description
1 MIC_L 2 Ground 3 MIC_R 4 N/C 5 LINE OUT_R 6 MIC Detect 7 SENSE 8 N/C 9 LINE OUT_L 10 LINE OUT Detect
23-
-
2 10
1 9 CN_AUDIO
Page 26
2.11 <USB2.0 Interface>
Based on Intel® ICH8-M, the board provides 4 USB2.0 ports. The USB2.0 interface provides up to 480Mbps of transferring rate.
Interface USB2.0
Controller ICH8-M
Transfer Rate Up to 480Mb/s
Output Current 500mA
1 2
2 10
CN_USB2
9 10
CN_USB1
Connector: CN_USB Type: 10-pin (5 x 2) header for USB Port
Pin Description Pin Description
1 VCC 2 VCC 3 Data0- 4 Data1­5 Data0+ 6 Data1+ 7 Ground 8 Ground 9 Ground 10 N/C
PS: The USB2.0 will be only active when you connecting with the USB2.0 devices, if you insert an USB1.1 device, the port will be changed to USB1.1 protocol automatically. The transferring rate of USB2.0 as 480Mbps is depends on device capacity, exact transferring rate may not be up to 480Mbps.
24-
-
Page 27
2.12 <Serial Port Jumper Setting >
The board provides two RS232 serial ports.
Connector: CN_COM1/2
Type: 20-pin (10 x 2) 1.27mm x 2.54mm-pitch header for COM1/2
Pin Description Pin Description
1 MDCD1 2 MSIN1 3 MSO1 4 MDTR1 5 GND 6 MDSR1 7 MRTS1 8 MCTS1 9 MRI1 10 NC 11 MDCD2 12 MSIN2 13 MSO2 14 MDTR2 15 GND 16 MDSR2 17 MRTS2 18 MCTS2 19 MRI2 20 NC
25-
-
CN_COM1/2
1 2
19 20
Page 28
2.13 <Power & FAN Connector >
The board requires DC input with 2-pin header, the input voltage is 12V, for the input current, please take a reference of the power consumption report on appendix.
2.13.1 <Power Input>
Connector: DC_IN
Type: 2-pin header
Pin Description Pin Description
1 Ground 2 +12V
DC_IN
1
2
26-
-
Page 29
2.13.2 <Power Output>
Connector: DC_OUT Type: 6-pin connector for +5V/+12V output
Pin Description
1 +12V 2 +12V 3 GND 4 GND 5 +5V 6 +5V
Note: Maximum output current 12V/1A, 5V/1A
DC_OUT
1
6
27-
-
Page 30
2.13.3 <Fan Connector>
Connector: SYSFAN, CPUFAN Type: 3-pin fan wafer connector
Pin Description Pin Description Pin Description
1 Ground 2 +12V 3 Speed detect
4 1
FAN
1
3
28-
-
Page 31
2.14 <Indicator and Switch>
The JFRNT provides front control panel of the board, such as power button, reset and beeper, etc. Please check well before you connecting the cables on the chassis.
Connector: JFRNT Type: onboard 10-pin (2 x 5) 2.54-pitch header
Function Signal PIN Signal
Power
Speaker
HDD LED
Power LED
Reset
JFRNT
1 2
PWRBT- 1 2 PWRBT+
SPK- 3 4 SPK+
HLED- 5 6 HLED+
PWRLED- 7 8 PWRLED+
Reset+ 9 10 Reset-
9 10
29-
-
Page 32
Chapter 3 <BIOS Setup>
The motherboard uses the Award BIOS for the system configuration. The Award BIOS in the single board computer is a customized version of the industrial standard BIOS for IBM PC AT-compatible computers. It supports Intel® x86 and compatible CPU architecture based processors and computers. The BIOS provides critical low-level support for the system central processing, memory and I/O sub-systems.
The BIOS setup program of the single board computer let the customers modif y the basic configuration setting. The settings are stored in a dedicated battery-backed memory, NVRAM, retains the information when the power is turned off. If the battery runs out of the power, then the settings of BIOS will come back to the default setting.
The BIOS section of the manual is subject to change without notice and is provi ded here for reference purpose only. The settings and configurations of the BIOS are current at the time of print, and therefore they may not be exactly the same as that displayed on your screen.
To activate CMOS Setup program, press <DEL> key immediately after you turn on the system. The following message “Press DEL to enter SETUP” should appear in the lower left hand corner of your screen. When you e nter the CMOS Setup Utility, the Main Menu will be displayed as Figure 4-1. You can use arrow keys to select your function, press Enter key to accept the selection and enter the sub-menu.
Figure 4-1 CMOS Setup Utility Main Screen
30-
-
Page 33
Appendix A <I/O Port Pin Assignment>
A.1 <LPC Port>
Connector: CN_LPC Type: 10-pin header for LPC Port
Pin Description Pin Description
1 LPC_CLK 2 RESET­3 LFRAME- 4 LAD3 5 LAD2 6 LAD1 7 LAD0 8 +3.3V 9 Ground 10 Ground
A.2 < CRT Port >
Connector: CRT Type: 15-pin D-sub female connector on rear panel
Pin Description Pin Description Pin Description
1 RED 6 Ground 11 N/C 2 GREEN 7 Ground 12 5VCDA 3 BLUE 8 Ground 13 HSYNC 4 N/C 9 LVGA5V 14 VSYNC 5 Ground 10 Ground 15 5VCLK
9
5 1
10 6
15 11
1
2 10
A.3 <LAN Port>
Connector: RJ45 Type: RJ45 connector with LED on rear panel
Pin 1 2 3 4 5 6 7 8
Description TRD0+ TRD0- TRD1+ TRD2+ TRD2- TRD1- TRD3+ TRD3-
31-
-
8 1
Page 34
Appendix B <Flash BIOS>
B.1 BIOS Auto Flash Tool
The board is based on Award BIOS and can be updated easily by the BIOS auto flash tool. You can download the tool online at the address below:
TUhttp://www.award.comUT TUhttp://www.commell.com.tw/support/support.htmUT
File name of the tool is “awdflash.exe”, it’s the utility that can write the data into the BIOS flash ship and update the BIOS.
B.2 Flash Method
1. Please make a bootable floppy disk.
2. Get the last .bin files you want to update and copy it into the disk.
3. Copy awardflash.exe to the disk.
4. Power on the system and flash the BIOS. (Example: C:/ awardflash XXX.bin)
5. Re-star the system.
Any question about the BIOS re-flash please contact your distributors or visit the web-site at below:
http://www.commell.com.tw/support/support.htm
32-
-
Page 35
Appendix C <System Resources>
C.1 <I/O Port Address Map> (LP-170G)
33-
-
Page 36
34-
-
Page 37
C.2 <Memory Address Map > (LP-170G)
35-
-
Page 38
C.3 < System IRQ Resources > (LP-170G)
36-
-
Page 39
Appendix E <Watch Dog timer Setting >
The watchdog timer makes the system auto-reset while it stops to work for a period. The integrated watchdog timer can be setup as system reset mode by program.
Timeout Value Range
- 1 to 255
- Second or Minute
Program Sample
Watchdog timer setup as system reset with 5 second of timeout
2E, 87 2E, 87 2E, 07 2F, 08 Logical Device 8 2E, 30 2F, 01 Activate 2E, F5 2F, 00 Set as Second* 2E, F6 2F, 05 Set as 5
* Minute: bit 3 = 1; Second: bit 3 = 0
You can select Timer setting in the BIOS, after setting the time options, the system will reset according to the period of your selection.
37-
-
Page 40
Contact Information
Any advice or comment about our products and service, or anything we can help you please don’t hesitate to contact with us. We will do our best to support you for your products, projects and business.
Taiwan Commate Computer Inc.
19F . , No.94, Sec. 1, Xintai 5th Rd., Xizhi Dist., New Taipei City
Address
TEL +886-2-26963909 FAX +886-2-26963911
22102, Taiwan
Website E-Mail
Facebook
Twitter https://twitter.com/Taiwan_Commate
TUhttp://www.commell.com.twUT TUinfo@commell.com.twUT (General Information)
TUtech@commell.com.twUT (Technical Support)
https://www.facebook.com/pages/Taiwan-Commate-Computer-Inc/547993955271899
Commell is our trademark of industrial PC division
38-
-
Loading...