Page 1
LE-565
5.25 inch Embedded Miniboard
User’s Manual
Edition 1.2
2011/03/10
Page 2
LE-565 User’s Manual
Copyright
Copyright 2011. All rights reserved. This document is copyrighted and all rights are
reserved. The information in this document is subject to change without prior notice to make
improvements to the products.
This document contains proprietary information and protect ed by copyright. No part of this
document may be reproduced, copied, or translated in any form or any means without prior
written permission of the manufacturer.
All trademarks and/or registered trademarks contains in this document are propert y of their
respective owners.
Disclaimer
The company shall not be liable for any incidental or consequenti al dam ages res ultin g from
the performance or use of this product.
The company does not issue a warranty of any kind, e xpress or implied, including without
limitation implied warranties of merchantability or fitness for a particular purpose.
The company has the right to revise the manual or include changes in th e specifications of
the product described within it at any time without notice and without obligation to notify any
person of such revision or changes.
Trademark
All trademarks are the property of their respective holders.
Any questions please visit our website at TUhttp://www.commell.com.twUT
2
Page 3
LE-565 User’s Manual
Packing List
Please check the package before you starting setup the system
Hardware:
LE-565 series motherboard x 1
Cable Kit:
44-pin ATA33 IDE Cable x 1
COM Port & Printer Port Cable x 1
Serial ATA Ribbon Cable x 2
PS2 Cable x 1
26-pin Slim Type Floppy Cable x 1
Power Cable x 1
40-pin ATA100 IDE Cable x 1
COM Port Cable x 1
Audio Port Cable x 1 USB Cable x 1
Printed Matters:
Driver CD x 1 (Including User’s Manual)
3
Page 4
LE-565 User’s Manual
Index
Chapter 1 <Introduction>.....................................................................................7
1.1 <Product Overview>.................................................................................7
1.2 <Product Specification>...........................................................................8
1.3 <Mechanical Drawing>...........................................................................10
1.4 <Block Diagram>....................................................................................11
Chapter 2 <Hardware Setup>.............................................................................12
2.1 <Connector Location>............................................................................12
2.2 <Jumper Reference> .............................................................................14
2.3 <Connector Reference>.........................................................................15
2.3.1 <Internal Connector>..................................................................15
2.3.2 <External Connector>.................................................................15
2.4 <CPU and Memory Setup>.................................................................... 16
2.4.1< CPU>........................................................................................16
2.4.2 <Memory> ..................................................................................16
2.5 <CMOS ATX Setup>..............................................................................17
2.6 <Enhanced IDE & CF Interface>............................................................18
2.7 <Serial ATA Interface>...........................................................................19
2.8 <Floppy Port>......................................................................................... 20
2.9 <LAN Interface>.....................................................................................21
2.10.1 <Analog VGA Interface> ..........................................................22
2.10.2 <Digital Display>.......................................................................23
2.11 <Onboard Audio Interface>..................................................................27
2.12 <USB2.0 Interface>..............................................................................28
2.13 <GPIO Interface>.................................................................................30
2.14 <Serial Port Jumper Setting >..............................................................31
2.15.1 <Power Input>..........................................................................33
2.15.2 <Power Output> .......................................................................34
4
Page 5
LE-565 User’s Manual
2.15.3 <Fan Connector>....................................................................34
2.16 <Indicator and Switch>.........................................................................35
Chapter 3 <System Configuration>...................................................................37
3.1 <SATA RAID Configuration>..................................................................37
3.2 <Audio Configuration> ...........................................................................39
3.3 <Display Configuration>.........................................................................40
Chapter 4 <BIOS Setup> .................................................................................... 44
Appendix A <I/O Port Pin Assignment> ...........................................................46
A.1 <IDE Port>.............................................................................................46
A.2 <Floppy Port> ........................................................................................48
A.3 <IrDA Port>............................................................................................48
A.4 < CRT Port >..........................................................................................49
A.5 <Serial ATA Port>..................................................................................49
A.6 <Serial Port>..........................................................................................49
A.7 <LAN Port>............................................................................................50
Appendix B <Flash BIOS>..................................................................................51
B.1 BIOS Auto Flash Tool .....................................................................51
B.2 Flash Method...................................................................................51
Appendix C <Programming GPIO’s>................................................................52
Appendix D <Watch Dog timer Setting >..........................................................53
Contact Information............................................................................................55
5
Page 6
LE-565 User’s Manual
(The Page is Left For Blank)
6
Page 7
LE-565 User’s Manual Introduction
Chapter 1 <Introduction>
1.1 <Product Overview>
LE-565 is the 5.25 inch embedded miniboard based on VIA chipset. It integrates VIA
embedded chipset for CN700 with VT8237R Plus, DDR 333/400 SDRAM, and serial ATA
with RAID to provide the economical embedded platform.
VIA CN700 & VT8237R Plus Chipset
The board comes with the VIA embedded chipset of CN700, supports DDR 333/400
SDRAM, integrated the S3 Graphics UniChrome Pro IGP graphics core, hardware MPEG-2
acceleration.
The VT8237R Plus provides the board to support Ultra V-Link (533MB/s) with CN700, two
serial ATA ports with RAID array function, 6 x USB2.0 ports and 5.1 channel AC97 audio.
Multimedia solution
Based on VIA CN700 chipset, the board provides 18/24-bit LVDS interface, which supports
dual independent display with CRT.
Onboard AC97 codec provides the high quality of sound including 5.1-channel stereo
DACs.
Four LAN Interface
LE-565 also comes with four Giga LAN interface, support boot-on-LAN and wake-on-LAN
function.
High Speed Hot-plug Interface
Based on VIA VT8237R Plus the board provides 6 USB2.0 interfaces with up to 480Mbps of
transferring rate.
Expanded UCR for remote Operating SETUP Bios Feature
Expanded Universal Console Redirection (UCR) is a feature for monitoring POST
messages and running Setup and an operation system from a remote serial terminal.
Product Overview
7
Page 8
LE-565 User’s Manual Introduction
1.2 <Product Specification>
General Specification
Form Factor 5.25 inch miniboard
CPU VIA V4/Eden 1.0GHz processor
L1/L2 Cache: 128/128KB
Front side bus: 400MHz
Memory 1 x 184-pin DDR 333/400 SDRAM up to 1GB,onboard optional
256MB DDR SDRAM
Unbufferred, none-ECC memory supported only
Chipset VIA CN700 and VT8237R Plus
BIOS Phoenix-Award v6.00PG 4Mb PnP flash BIOS
Green Function Power saving mode includes doze, standby and suspend modes.
ACPI version 1.0 and APM version 1.2 compliant
Watchdog Timer System reset programmable watchdog timer with 1 ~ 255
sec./min. of timeout value
Real Time Clock VIA VT8237R Plus built-in RTC with lithium battery
Enhanced IDE Enhanced IDE interface supports dual channels and up to 4
ATAPI devices at Ultra DMA133
One 40-pin and one 44-pin IDE port onboard
One Compact Flash Type II socket on solder side
Serial ATA VIA VT8237R Plus integrates 2 Serial ATA interface
RAID 0, 1 array Technology supported
Multi-I/O Port
Chipset VIA VT8237R Plus with Winbond W83697UG controller
Serial Port One external & three internal RS-232 serial ports
USB Port Four external & four internal Hi-Speed USB 2.0 ports with
480Mbps of transfer rate
Parallel Port One 26-pin internal parallel port
Floppy Port One slim type Floppy port
IrDA Port One IrDA compliant Infrared interface supports SIR
K/B & Mouse Internal PS/2 keyboard and mouse
GPIO One 12-pin Digital I/O connector with 8-bit programmable I/O
interface
Hardware Monitor Fan speed, CPU temperature and voltage monitoring
VGA Display Interface
Chipset VIA CN700 built-in S3 Graphics UniChrome Pro IGP graphics core
Core Frequency 200MHz
Memory BIOS selectable 16/32/64MB shard with system memory
Display Type CRT, LCD monitor with analog display
Connector External DB15 female connector on rear I/O panel
Internal 40-Pin LVDS connector
8
Product Specification
Page 9
LE-565 User’s Manual Introduction
Ethernet Interface
Chipset REALTEK 8110S-32
Type 10Base-T / 100Base-TX /1000Base-TX
auto-switching Fast Ethernet
Full duplex, IEEE802.3U compliant
Connector Four External RJ45 connectors with LED on rear I/O panel
Audio Interface
Chipset REALTEK ALC655
Interface 5.1 channel surround audio with Line-in, Line-out and MIC-in
Connector Onboard audio connector with pin header
Onboard CD-IN connector
Expansive Interface
PCI 1 x PCI slot supports up to two PCI devices through riser card
Mini PCI 1 x Mini PCI socket
Power and Environment
Power
DC 12V input with external DC Jack or onboard 4-pin connector
Requirement
Dimension 146 (L) x 203 (H) mm
Temperature Operating within 0 ~ 60P
Storage within -20 ~ 85
o
P
C (32 ~ 140P
o
P
P
C (-4 ~ 185P
o
P
F)
o
P
F)
Software support
Operation
System
Windows 2000, Windows XP,Windows CE 4.0 or later, Windows XP
Embedded Linux (Fedora Core 1, Mandrake 9.2 and Red H at 9.0)
Ordering Code
LE-565-P
VIA V4 Eden 1G With Onboard VGA, AUDIO, Giga LAN, USB2.0,
4 x COM, FDD, LPT, GPIO, LVDS, Mini PCI, SATA
LE-565-256
SPD-080-12
The same as above and with 256MB DDR SDRAM
AC-DC Adapter with 12V, 80W DC Jack output
1. The specifications may be different as the actual production.
For further product information please visit the website at
Product Specification
TUhttp://www.commell.com.twUT
9
Page 10
LE-565 User’s Manual Introduction
1.3 <Mechanical Drawing>
Mechanical Drawing
10
Page 11
LE-565 User’s Manual Introduction
p
1.4 <Block Diagram>
Eden nanoBGA2
CRT/LCD Monitor
VT1636 LVDS
6 x USB2.0 Ports
AC97 ALC655
BIOS
4 x Serial ports
1 x Floppy port
1 x Parallel port
CN700
VT8237R+
W83782G
Ultra V-Link
533MB/s
1 x 184-pin
DDR333/400
to 1GB
U
2 x IDE
4 x 8110S-32
PCI
2 x SATA
LAN1/2/3/4
8-bit GPIO
PS/2 , KB/MS
Block Diagram
Hardware Monitor
IrDA
11
Page 12
LE-565 User’s Manual Hardware Setup
_
Chapter 2 <Hardware Setup>
2.1 <Connector Location>
DIMM
CPUFAN
CN_LVDS
JLED0/1/2/3
CN_INV SYSFAN JFRNT IDE2
IDE1
CN_PWR
CN_12V
CN_COM2/3/4
CN_PS2
CDIN
CN_USB2/3
FDD
SATA1/2
PCI
DIO
CN
MINIPCI
CN_IR
LPT
CN_AUDIO
CN_CRT
Connector Location
12
Page 13
LE-565 User’s Manual Hardware Setup
CF
DC_IN LAN1/2/3/4 COM1 USB CRT
Connector Location
13
Page 14
LE-565 User’s Manual Hardware Setup
2.2 <Jumper Reference>
Jumper Function
JRTC CMOS Operating/Clear Setting
JCFSEL Compact Flash address mode setting
JVLCD LCD Panel Voltage Setting
JAT AT/ATX mode setting
JCSEL1/2 COM2 RS232/422/485 mode setting
JAT
JCFSEL
JRTC
JVLCD
14
JCSEL1/2
Jumper Reference
Page 15
LE-565 User’s Manual Hardware Setup
2.3 <Connector Reference>
2.3.1 <Internal Connector>
Connector Function Remark
DIMM 184-pin DDR SDRAM DIMM Standard
IDE1 40-pin primary IDE connector Standard
IDE2 44-pin secondary IDE connector Slim
FDD 26-pin slim type floppy connector Slim
SATA1/2 7-pin Serial ATA connector Standard
CN_12V 4-pin power supply connector Standard
CN_AUDIO 5 x 2-pin audio connector Standard
CDIN 4-pin CD-ROM audio input connector Standard
CN_DIO 6 x 2- pin digital I/O connector Standard
CN_USB 2/3 5 x 2-pin USB connector Standard
CPUFAN 3-pin CPU cooler fan connector Standard
SYSFAN 3-pin system cooler fan connector Standard
CN_COM2/3/4 5 x 2-pin RS232 serial port Standard
CN_IR 5-pin IrDA connector Standard
CF Compact Flash Type II socket Standard
CN_LVDS 20 x 2-pin LVDS LCD interface Standard
CN_INV 5-pin LCD inverter connector Standard
JLED0/1/2/3 3 x 2-pin LED connector Standard
CN_PWR 4-pin power output connector Standard
PCI Slim 32bit PCI slot Slim
MINIPCI Mini-PCI socket Standard
LPT 13 x 2-pin printer connector Standard
CN_PS2 5 x 2-pin PS2 connector Standard
JFRNT 14-pin switch/indicator connector Standard
2.3.2 <External Connector>
Connector Function Remark
CRT DB15 VGA connector Standard
USB Dual USB 2.0 connector Standard
COM1 DB9 Serial port connector Standard
RJ45_1/2/3/4 Four RJ45 LAN connector Standard
DC_IN DC 12V input jack Standard
Connector Reference
15
Page 16
LE-565 User’s Manual Hardware Setup
2.4 <CPU and Memory Setup>
2.4.1< CPU>
The board supports VIA Eden processor, default ratio is Eden 1G (400MHz) with heatsink
only.
2.4.2 <Memory>
The board supports one 184-pin DDR333/400 SDRAM and up to 1GB of capacity, only
non-ECC, unbuffered memory is supported.
DIMM
16
80-pin104-pin
Please check the pin number to match the socket side well
before installing memory module.
CPU and Memory Setup
Page 17
LE-565 User’s Manual Hardware Setup
2.5 <CMOS ATX Setup>
The board’s data of CMOS can be setting in BIOS. If the board refuses to boot due to
inappropriate CMOS settings, here is how to proceed to clear (reset) the CMOS to its
default values.
Jumper: JRTC
Type: Onboard 3-pin jumper
JRTC Mode
1-2 Clear CMOS
2-3 Normal Operation
Default setting
Jumper: JAT
Type: Onboard 3-pin jumper
JAT Mode
1-2 AT mode
2-3 ATX mode -default
Default setting
CMOS A TX Setup
1
JAT
3
JRTC
1
3
17
Page 18
LE-565 User’s Manual Hardware Setup
2.6 <Enhanced IDE & CF Interface>
The board supports two enhanced IDE interface, dual channel for 4 ATAPI devices with
ATA33. Based on embedded application, the board has one 44-pin IDE connector +5V
supported for disk on module.
The board also provides a Compact Flash Type II socket with jumper (JCFSEL) selectable
slave/Master mode on secondary IDE channel.
Jumper: JCFSEL
Type: onboard 3-pin header
JCFSEL Mode
1-2 Master
2-3 Slave
Default setting
3
1
JCFSEL
18
Enhanced IDE&CF Interface
Page 19
LE-565 User’s Manual Hardware Setup
2.7 <Serial ATA Interface>
Based on VIA VT8237R Plus Southbridge, the board supports two Serial AT A interfaces
with RAID 0 and 1 array function. The following is the list of the specific ation of the Serial
ATA.
1. Complies with Serial ATA Specification Revision 1.0
2. Dual Channel master mode PCI
3. On-chip two-channel Serial ATA (S-ATA) PHY for support of up to two S-ATA devices
directly.
4. S-ATA drive transfer rate is capable of up to 150 MB/s per channel (serial speed of 1.5
Gbit/s).
For more information please visit VIA website (www.via.com.tw)
SATA1
SATA2
Serial A TA Interface
19
Page 20
LE-565 User’s Manual Hardware Setup
2.8 <Floppy Port>
The board provides a slim type floppy port; please use the 26-pin ribbon cable in the
package to connect the floppy device.
FDD
20
Floppy rear side
4. Lift up this plastic bar
5. Slot the cable in (Blue paste for outside)
6. Press back the plastic bar
1. Lift up the brown plastic bar
2. Slot the cable in (Blue paste for
brown bar side)
3. Press back the plastic bar
Floppy Port
Page 21
LE-565 User’s Manual Hardware Setup
2.9 <LAN Interface>
The board provides four GigaLAN interfaces with REALTEK 8110S-32 PCI controller, and
compliant with standard IEEE 802.3 Ethernet interface for 100BASE-TX.
LAN_1/2/3/4
LAN Interface
21
Page 22
LE-565 User’s Manual Hardware Setup
2.10 <Onboard Display Interface>
Based on VIA CN700, the board supports integrated S3 Graphics UniChrome Pro IGP
graphics, with BIOS selectable 16/32/64MB shared with system memory for frame buffer.
2.10.1 <Analog VGA Interface>
The board provides a DB15 CRT connector on the rear I/O panel.
CRT
22
Onboard Display Interface
Page 23
LE-565 User’s Manual Hardware Setup
2.10.2 <Digital Display>
The board provides one 40-pin LVDS connector for 18/24-bit single/dual channel panels,
supports up to 1600 x 1200 (UXGA) of resolution, with one LCD backlight inverter connector
and one jumper for panel voltage setting
JVLCD
CN_LVDS
1
2
40
39
1
3
5
1
CN_INV
JVLCD
Digital Display
23
Page 24
LE-565 User’s Manual Hardware Setup
Connector: CN_INV Connector: JVLCD
Type: 5-pin LVDS Power Header Type: 3-pin Power select Header
Connector model: JST B5B-XH-A
Pin Description Pin Description
1 +12V 1 VCC(5V)
2 GND 2 LCDVCC
3 GND 3 VCC3(3.3)
4 GND
5 ENABKL
Connector: CN_LVDS
Type: onboard 40-pin connector for LVDS connector
Connector model: HIROSE DF13-40DP-1.25V
Pin Signal Pin Signal
2 LCDVCC 1 LCDVCC
4 GND 3 GND
6 ATX0- 5 BTX0-
8 ATX0+ 7 BTX0+
10 GND 9 GND
12 ATX1- 11 BTX114 ATX1+ 13 BTX1+
16 GND 15 GND
18 ATX2- 17 BTX220 ATX2+ 19 BTX2+
22 GND 21 GND
24 ACLK- 23 BTX326 ACLK+ 25 BTX3+
28 GND 27 GND
30 ATX3- 29 BCLK32 ATX3+ 31 BCLK+
34 GND 33 GND
36 N/C 35 N/C
38 N/C 37 N/C
40 N/C 39 N/C
24
Digital Display
Page 25
LE-565 User’s Manual Hardware Setup
To setup the LCD, you need the component below:
1. A panel with LVDS interfaces.
2. An inverter for panel’s backlight power.
3. A LCD cable and an inverter cable.
For the cables, please follow the pin assignm ent of the connector to make a cable, because
every panel has its own pin assignment, so we do not provide a standard cable; please find a
local cable manufacture to make cables.
LCD Installation Guide:
1. Preparing the LS-570, LCD panel and the backlight inverter.
2. Please check the datasheet of the panel to see the voltage of the panel, and set the
jumper JVLCD to +5V or +3.3V.
3. You would need a LVDS type cable.
Panel side
For sample illustrator only
4. To connect all of the devices well.
Digital Display
Board side
25
Page 26
LE-565 User’s Manual Hardware Setup
After setup the devices well, you need to select the LCD panel type in the BIOS.
The panel type mapping is list below:
LE-565 BIOS panel type selection form
VGA ROM VERSION: 9Y-9X-00-20
NO. Resolution Color Channel
0 640 x 480 18 1
1 800 x 600 18 1
2 1024 x 768 18 1
3 1280 x 768 18 1
4 1280 x 1024 24 1
5 1400 x 1050 18 2
6 1600 x 1200 18 2
7 1280 x 800 18 1
8 800 x 480 18 2
9 1024 x 768 18 2
A 1024 x 768 24 1
B 1024 x 768 24 2
C 1280 x 768 24 1
D 1280 x 1024 24 2
E 1400 x 1050 24 2
F 1600 x 1200 24 2
26
Digital Display
Page 27
LE-565 User’s Manual Hardware Setup
2.11 <Onboard Audio Interface>
The board provides the onboard AC97 5.1-channel audio int erface with Realteck ALC655.
Connector: CN_AUDIO
Type: 10-pin (2 x 5) header (pitch = 2.54mm)
Pin Description Pin Description
1 Line/SURR – Left 2 Ground
3 Line/SURR – Right 4 MIC1/CEN
5 MIC2/LEF 6 Ground
7 N/C 8 Line Out– Left
9 Line Out – Right 10 Ground
Connector: CDIN
Type: 4-pin header (pitch = 2.54mm)
Pin Description
1 CD – Left
2 Ground
3 Ground
4 CD – Rig ht
Onboard Audio Interface
CDIN
CDIN
CN_AUDIO
1
1 4
10
27
Page 28
LE-565 User’s Manual Hardware Setup
2.12 <USB2.0 Interface>
Based on VIA VT8237R Plus, the board provides 6 USB2.0 ports. The USB2.0 interface
provides up to 480Mbps of transferring rate.
Interface USB2.0
Controller VIA VT8237R+
Transfer Rate Up to 480Mb/s
Output Voltage 500mA
1
CN_USB
10
28
USB
USB2.0 Interface
Page 29
LE-565 User’s Manual Hardware Setup
Connector: CN_USB
Type: 10-pin (5 x 2) header for USB2/3 Ports
Pin Description Pin Description
1 VCC 2 VCC
3 Data0- 4 Data15 Data0+ 6 Data1+
7 Ground 8 Ground
9 Ground 10 N/C
PS: The USB2.0 will be only active when you connecting with the USB2.0 devices, if you
insert an USB1.1 device, the port will be changed to USB1.1 protocol automatic ally. The
transferring rate of USB2.0 as 480Mbps is depending on device capacity, exact transferring
rate may not be up to 480Mbps.
USB2.0 Interface
29
Page 30
LE-565 User’s Manual Hardware Setup
2.13 <GPIO Interface>
The board provides a programmable 8-bit digital I/O interface; you can use this general
purpose I/O port for system control like POS or KIOSK.
Connector: CN_DIO
Type: onboard 2 x 6-pin header, pitch=2.0mm
Pin Description Pin Description
1 Ground 2 Ground
3 GP0 4 GP4
5 GP1 6 GP5
7 GP2 8 GP6
9 GP3 10 GP7
11 VCC 12 +12V
30
CN_DIO
2
1
12
11
GPIO Interface
Page 31
LE-565 User’s Manual Hardware Setup
2.14 <Serial Port Jumper Setting >
The board provides four RS232 serial ports, with jumper selectable RS422/485 for COM2.
Connector: CN_COM2/3/4
Type: 10-pin (5 x 2) header for COM2/3/4
Pin Description Pin Description
1 DCD/422TX-/485- 2 RXD/422TX+/485+
3 TXD/422RX+ 4 DTR/422RX5 GND 6 DSR
7 RTS 8 CTS
9 RI 10 N/C
JCSEL1 JCSEL2
12
2
RS-232
1
RS-485
RS-422
Power and Fan Connector
5
6
11
12
31
Page 32
LE-565 User’s Manual Hardware Setup
JCSEL2
JCSEL1
CN_COM2/3/4
1
10
COM
2.15 <Power and Fan Connector>
32
GPIO Interface
Page 33
LE-565 User’s Manual Hardware Setup
The board comes with a 2-pin DC-Jack power connector for DC 12V input, it also has one
4-pin P4 additional use power connector for internal power supply, you can choose one pf
them to meet your plication.
2.15.1 <Power Input>
Connector:CN_12V
Type: 4-pin DC power connector
Pin Description Pin Description
1 +12V 2 +12V
3 Ground 4 Ground
13
SYSFAN
1
3
CPUFAN
CN_12V
1
3
2
4
1
4
CN_PWR
Power and Fan Connector
33
Page 34
LE-565 User’s Manual Hardware Setup
2.15.2 <Power Output>
Connector: CN_PWR
Type: 4-pin P-type connector for +5V/+12V output
Pin Description Pin Description Pin Description Pin Description
1 +5V 2 Ground 3 Ground 4 +12V
Note: Maximum output voltage: 12V/5A & 5V/3A
2.15.3 <Fan Connector>
Connector: CPUFAN, SYSFAN
Type: 3-pin fan wafer connector
Pin Description Pin Description Pin Description
1 Ground 2 +12V 3 Fan Control
Floppy
ATAPI Drives
Relative Accessory
34
Power Output
Page 35
LE-565 User’s Manual Hardware Setup
2.16 <Indicator and Switch>
The JFRNT provides front control panel of the board, such as power button, reset and
beeper, etc. Please check well before you connecting the cables on the chassis.
Connector: JFRNT
Type: onboard 14-pin (2 x 7) 2.54-pitch header
Function Signal PIN Signal Function
IDE LED
Reset
Power
Button
HDLED+ 1 2 PWRLED+
HDLED- 3 4 N/C
Reset+ 5 6 PWRLED-
Reset- 7 8 SPK+
N/C 9 10 N/C
PWRBT+ 11 12 N/C
PWRBT- 13 14 SPK-
14
Power
LED
Speaker
1
JFRNT
Indicator and Switch
35
Page 36
LE-565 User’s Manual
(This Page is Left For Blank)
36
Page 37
LE-565 User’s Manual System Configuration
Chapter 3 <System Configuration>
3.1 <SATA RAID Configuration>
The board supports two Serial ATA ports onboard, and supports RAID 0, 1 and JBOD disk
array, the RAID 0, 1 and JBOD are specified below:
RAID 0 (Stripping): Two hard drives operating as one drive for optimized data R/W
performance. It needs two unused drives to build this operation.
RAID 1 (Mirroring): Copies the data from first drive to second drive for data security, and if
one drive fails, the system would access the applications to the workable drive. It needs two
unused drives or one used and one unused driv e to build this operation. The second drive
must be the same or lager size than first one.
JBOD (Span): As different as RAID 0, the JBOD combines two disks as one without any
fault tolerance and I/O performance enhancement.
To build Serial ATA disk array, please press <TAB> while booting up the system before
entering OS, and follow the instructions to edit the RAID function.
(Selectable Functions)
SATA RAID Configuration
(Option Instruction)
(Disk Statement)
37
Page 38
LE-565 User’s Manual
You also can edit disk array under OS, please install the VIA RAID Utility in the driver CD.
(Click here to build RAID 0)
(To getting start, please click here to learn more information)
(Click here to build RAID JBOD)
38
(Click here to build RAID 0)
SATA RAID Configuration
Page 39
LE-565 User’s Manual System Configuration
3.2 <Audio Configuration>
The board provides 5.1 channel audio interface with driver installed, please install the
Realtek ALC655 audio driver in the CD before getting start to enjoy the 5.1 channel sound
system.
Audio Configuration
39
Page 40
LE-565 User’s Manual
3.3 <Display Configuration>
The board provides onboard analog VGA interface, and optional digital display interface
with LVDS , please install the VIA video driver before enjoy the vivid display.
Based on the VIA CN700 with S3 UniChrome Pro graphic, the board provides dual
display function for clone or extended desktop modes with secondary display device
attached.
After installing video driver, please launch the desktop display properties.
For secondary display device, you have two options selectable.
or more display properties setting, please click “Advanced” button.
Please select S3Display for advanced device setting.
When you set dual display clone mode, you’ll see the sam e screen display on two
devices.
When you set the dual display for extended desktop mode, you can have the independent
desktop on the second device.
40
Display Configuration
Page 41
LE-565 User’s Manual System Configuration
Two controllers for each display device
There are two options for secondary display device
For more display properties setting, please click “Advanced” button.
Display Configuration
41
Page 42
LE-565 User’s Manual
Please select S3Display for advanced device setting.
Connected Devices
Click check box to
enable/disable device
Specified display setup if available
When you set dual display clone mode, you’ll see the same screen display on two devices.
When you set the dual display for extended desktop mode, you can have the independent
desktop on the second device.
42
Display Configuration
Page 43
LE-565 User’s Manual
(This Page is Left for Blank)
43
Page 44
LE-565 User’s Manual BIOS Setup
Chapter 4 <BIOS Setup>
The motherboard uses the Award BIOS for the system configuration. The Award
BIOS in the single board computer is a customized version of the industrial standard
BIOS for IBM PC AT-compatible computers. It supports Intel x86 and compatible CPU
architecture based processors and computers. The BIOS provides critical low-level
support for the system central processing, memory and I/O sub-systems.
The BIOS setup program of the single board computer let the customers modify the
basic configuration setting. The settings are stored in a dedicated battery-backed
memory, NVRAM, retains the information when the power is turned off. If the battery
runs out of the power, then the settings of BIOS will come back to the default setting.
The BIOS section of the manual is subject to change without notice and is provided here
for reference purpose only. The settings and configurations of the BIOS are current at
the time of print, and therefore they may not be exactly the same as that displayed on
your screen.
To activate CMOS Setup program, press ＜DEL＞ key i mmediately after you turn on
the system. The following message “Press DEL to enter SETUP” should appear in the
lower left hand corner of your screen. When you enter the CMOS Setup Utility, the Main
Menu will be displayed as Figure 4-1. You can use arrow keys to select your function,
press ＜Enter＞ key to accept the selection and enter the sub-menu.
Figure 4-1 CMOS Setup Utility Main Screen
44
Page 45
LE-565 User’s Manual
(This Page is Left for Blank)
45
Page 46
LE-565 User’s Manual I/O Port Pin Assignment
Appendix A <I/O Port Pin Assignment>
A.1 <IDE Port>
Connector: IDE1
Type: 40-pin (20 x 2) box header
Pin Description Pin Description
1 Reset 2 Ground
3 D7 4 D8
5 D6 6 D9
7 D5 8 D10
9 D4 10 D11
11 D3 12 D12
13 D2 14 D13
15 D1 16 D14
17 D0 18 D15
19 Ground 20 VCC
21 REQ 22 Ground
23 IOW-/STOP 24 Ground
25 IOR-/HDMARDY 26 Ground
27 IORDY/DDMARDY 28 IDESEL
29 DACK- 30 Ground
31 IRQ 32 N/C
33 A1 34 CBLID
35 A0 36 A2
37 CS0 (MASTER CS) 38 CS1 (SLAVE CS)
39 LED ACT- 40 Ground
39
40
1
2
46
IDE Port
Page 47
LE-565 User’s Manual I/O Port Pin Assignment
Connector: IDE2
43
1
Type: 44-pin (22 x 2) box header
44
2
Pin Description Pin Description
1 Reset 2 Ground
3 D7 4 D8
5 D6 6 D9
7 D5 8 D10
9 D4 10 D11
11 D3 12 D12
13 D2 14 D13
15 D1 16 D14
17 D0 18 D15
19 Ground 20 N/C
21 REQ 22 Ground
23 IOW-/STOP 24 Ground
25 IOR-/HDMARDY 26 Ground
27 IORDY/DDMARDY 28 Ground
29 DACK- 30 Ground
31 IRQ 32 N/C
33 A1 34 SD
35 A0 36 A2
37 CS1 38 CS3
39 ASP1 40 Ground
41 Vcc 42 Vcc
43 Ground 44 Ground
IDE Port
47
Page 48
LE-565 User’s Manual I/O Port Pin Assignment
A.2 <Floppy Port>
Connector: FDD
Type: 26-pin connector
Pin Description Pin Description
1 VCC 2 INDEX
3 VCC 4 DRV0
5 VCC 6 DSKCHG
7 DRV1 8 N/C
9 MTR1 10 MTR0
11 RPM 12 DIR
13 N/C 14 STEP
15 Ground 16 WRITE DATA
17 Ground 18 WRITE GATE
19 N/C 20 TRACK 0
21 N/C 22 WRPTR
23 Ground 24 RDATA25 Ground 26 SEL
A.3 <IrDA Port>
Connector: CN_IR
Type: 5-pin header for SIR Port
Pin Description
1 Vcc
2 N/C
3 IRRX
4 Ground
5 IRTX
1 5
48
Floppy Port
Page 49
LE-565 User’s Manual I/O Port Pin Assignment
6
10
11
12
13
14
15
A.4 < CRT Port >
Connector: CRT
Type: 15-pin D-sub female connector on panel
1
2
3
4
5
Pin Description Pin Description Pin Description
1 RED 6 Ground 11 N/C
2 GREEN 7 Ground 12 5VCDA
3 BLUE 8 Ground 13 HSYNC
4 N/C 9 LVGA5V 14 VSYNC
5 Ground 10 Ground 15 5VCLK
A.5 <Serial ATA Port>
1 7
Connector: CN_SATA1/2
Type: 7-pin wafer connector
1 2 3 4 5 6 7
GND RSATA_TXP1 RSATA_TXN1 GND RSATA_RXN1 RSATA_RXP1 GND
5
A.6 <Serial Port>
Connector: COM1
4
3
2
1
Type: 9-pin D-sub male connector on rear panel
Pin Description Pin Description
1 DCD 6 DSR
2 SIN 7 RTS
3 SO 8 CTS
4 DTR 9 RI
5 Ground
9
8
7
6
CRT Port
49
Page 50
LE-565 User’s Manual
A.7 <LAN Port>
Connector: RJ45_1/2/3/4
Type: RJ45 connector with LED on rear panel
Pin 1 2 3 4 5 6 7 8
Description TX+ TX- RX+ N/C N/C RX- N/C N/C
Connector: JLED0/1/2/3
Type: 6-pin header for LAN LED
Pin Description Pin Description
1 ACT+ 2 ACT3 Link100+ 4 Link1005 Link 1G+ 6 Link 1G-
1
8
1
6
50
Page 51
LE-565 User’s Manual
Appendix B <Flash BIOS>
B.1 BIOS Auto Flash Tool
The board is based on Award BIOS and can be updated easily by the BIOS auto flash
tool. You can download the tool online at the address below:
TUhttp://www.award.comUT
TUhttp://www.commell.com.tw/support/support.htmUT
File name of the tool is “awdflash.exe”, it’s the utility that can write the data into the
BIOS flash ship and update the BIOS.
B.2 Flash Method
1. Please make a bootable floppy disk.
2. Get the last .bin files you want to update and copy it into the disk.
3. Copy awardflash.exe to the disk.
4. Power on the system and flash the BIOS. (Example: C:/ awardflash XXX.bin)
5. Re-star the system.
Any question about the BIOS re-flash please contact your distributors or visit the
web-site at below:
http://www.commell.com.tw/support/support.htm
51
Page 52
LE-565 User’s Manual Programming GPIO’s
Appendix C <Programming GPIO’s>
The GPIO can be programmed with the MSDOS debug program using simple
IN/OUT commands. The following lines show an example how to do this.
GPIO0...GPIO7 bit0……bit7
-o 2E 87 ;enter configuration
-o 2E 87
-o 2E 2A
-o 2F FD ;enable GPIO function
-o 2E 07
-o 2F 07 ;enable GPIO configuration
-o 2E F0
-o 2F xx ;set GPIO as input/output; set ‘1’ for input,’0’for output
-o 2E F1
-o 2F xx ;if set GPIO’s as output, in this register its value can be set
Optional :
-o 2E F2
-o 2F xx ; Data inversion register ; ‘1’ inverts the current value of the
bits ,’0’ leaves them as they are
-o 2E 30
-o 2F 01 ; active GPIO’s
For further information ,please refer to Winbond W83697UG datasheet.
52
Programming GPIO’s
Page 53
LE-565 User’s Manual Watch Dog timer Setting
Appendix D <Watch Dog Timer Setting >
The watchdog timer makes the system auto-reset while it stops to work for a period. The
integrated watchdog timer can be setup as system reset mode by program.
Timeout Value Range
- 1 to 255
- Second or Minute
Program Sample
Watchdog timer setup as system reset with 5 second of timeout
2E, 87
2E, 87
2E, 07
2F, 08 Logical Device 8
2E, 30 Activate
2F, 01
2E, F5 Set as Second*
2F, 00
2E, F6 Set as 5
2F, 05
* Minute: bit 3 = 0; Second: bit 3 = 1
You can select Timer setting in the BIOS, after setting the time options, the system will
reset according to the period of your selection.
Watch Dog timer Setting
53
Page 54
LE-565 User’s Manual
(This Page is Left for Blank)
54
Page 55
LE-565 User’s Manual
Contact Information
Any advice or comment about our products and service, or
anything we can help you please don’t hesitate to contact with us.
We will do our best to support you for your products, projects and
business.
Taiwan Commate Computer Inc.
19F., No.94, Sec. 1, Xintai 5th Rd., Xizhi Dist., New Taipei City
Address
TEL +886-2-26963909
FAX +886-2-26963911
22102, Taiwan
Website
E-Mail
Facebook
Twitter https://twitter.com/Taiwan_Commate
TUhttp://www.commell.com.twUT
TUinfo@commell.com.twUT (General Information)
TUtech@commell.com.twUT (Technical Support)
https://www.facebook.com/pages/Taiwan-Commate-Computer-Inc/547993955271899
Commell is our trademark of industrial PC division
Contact Information
55
Loading...