COMMELL LE-37E User Manual

Page 1
LE-37E
3.5 inch Motherboard
Users Manual
Edition 1.0
2015/08/04
Page 2
LE-37E Users Manual
-1-
Copyright
Copyright 2015, all rights reserved. This document is copyrighted and all rights are reserved. The information in this document is subject to change without prior notice to make improvements to the products. This document contains proprietary information and protected by copyright. No part of this document may be reproduced, copied, or translated in any form or any means without prior written permission of the manufacturer. All trademarks and/or registered trademarks contains in this document are property of their respective owners.
Disclaimer
The company shall not be liable for any incidental or consequential damages resulting from the performance or use of this product. The company does not issue a warranty of any kind, express or implied, including without limitation implied warranties of merchantability or fitness for a particular purpose. The company has the right to revise the manual or include changes in the specifications of the product described within it at any time without notice and without obligation to notify any person of such revision or changes.
Trademark
All trademarks are the property of their respective holders.
Any questions please visit our website at
TUhttp://www.commell.com.twUT
Page 3
LE-37E Users Manual
-2-
1 x LE-37E 3.5 inch Motherboard (include HeatSink)
1 x SATA cable
(OALSATA3-L / 1040529)
1 x PS/2 Keyboard & Mouse cable
(OALPS2/KM / 1040131)
1 xDC Input Power cable
(OALDC-A / 1040433)
1 x Audio cable
(OALPJ-HDUNB / 1040123)
1 xUSB2.0 cable
(OALUSBA-3 / 1040173)
1 x Onboard DVI-D cable
(BADPDVI_A & OALDVI-DF13
/ 4120008021 & 1040483)
1 x Dual COM cable
(OALES-BKU2-H14NB / 1040379)
1 x COM Cable
(OALES-BKU1NB / 1040086)
1 x SATA Power cable
(OAL4P-S2 / 1040054)
1 x 1 to 3 Power output cable
(OAL4P-2 / 1040051)
Packing List:
Please check the package content before you starting using the board.
Optional:
Page 4
LE-37E Users Manual
-3-
Index
Chapter 1 <Introduction>............................................................... 4
1.1 <Product Overview> ................................................................................. 4
1.2 <Product Specification> ........................................................................... 5
1.3 <Mechanical Drawing> ............................................................................. 6
1.4 <Block Diagram> ...................................................................................... 7
Chapter 2 <Hardware setup> ......................................................... 8
2.1 <Connector Location and Reference> ..................................................... 8
2.1.1 <Internal connectors list> ............................................................. 9
2.1.2 <External connectors list> ............................................................ 9
2.2 <Jumper Location and Reference> ........................................................ 10
2.2.1 <Jumper list> .............................................................................. 10
2.2.2 <Clear CMOS and Power on type selection> ............................ 10
2.3 <Installing the Memory> ......................................................................... 11
2.4 <I/O interface> ........................................................................................ 12
2.4.1 <Serial ATA interface> ................................................................ 12
2.4.2 <Ethernet interface> ................................................................... 12
2.4.3 <Display interface> ..................................................................... 13
2.4.4 <Serial Port interface> ................................................................ 15
2.4.5 <USB interface> ......................................................................... 17
2.4.6 <Audio interface> ....................................................................... 17
2.4.7 <Expansion slot> ........................................................................ 18
2.4.8 <Front panel switch and indicator> ............................................ 19
2.4.9 <Other interface> ........................................................................ 19
2.5 <Power supply>...................................................................................... 21
2.5.1 <Power input> ............................................................................ 21
2.5.2 <Power output> .......................................................................... 22
Appendix A <Flash BIOS> ........................................................... 23
Appendix B <Installation driver Notes> ..................................... 24
Appendix C <LCD Panel Type select> ........................................ 25
Appendix D <Programmable GPIO > .......................................... 26
Appendix E <Programmable Watch Dog Timer> ....................... 27
Contact information ..................................................................... 28
Page 5
LE-37E Users Manual
-4-

Chapter 1 <Introduction>

1.1 <Product Overview>

LE-37E is 3.5 inch Motherboard which supports 5th/4th Generation Intel® CoreU-series i7,
i5, i3, Celeron Mobile Processor with Wildcat Point PCH-LP, integrated HD Graphics,
DDR3L memory, Realtek High Definition Audio, Intel Gigabit LAN, Serial ATA3 with AHCI
function for a system.
Intel Broadwell-U Processor with Wildcat Point PCH-LP
The 5th Generation Intel® Core U-series processor family is the next generation and
compatible with Haswell-U, multi-core mobile processor built on 14/22 nanometer process
with MCP technology.
The Broadwell-U has a lower TDP 15W and 28W, it provides new HD Graphics (GT2 and
GT3 GPU) support triple display at the same time, maximum supported is up to 16GB of
DDR3L, better performance, flexibility and more enhanced security that is suitable for a variety of intelligent systems the ideal choice.
All in One multimedia solution
The board provides high performance onboard graphics, 24-bit dual channel LVDS interface,
DisplayPort, HDMI, and High Definition Audio, to meet the very requirement of the
multimedia application.
Flexible Expansion Interface
The board provides two MiniPCIe and support mSATA, SIM.
Page 6
LE-37E Users Manual
-5-
System
Processor
Intel® Broadwell/Haswell Core™ i7, i5, i3, Celeron U-series Processor FCBGA1168 with MCP
Chipset
Wildcat Point-LP
Memory
1 x DDR3L SO-DIMM 1333/1600 MHz up to 8GB Support Non-ECC, unbuffered memory only
Watchdog Timer
Generates a system reset with internal timer for 1min/s ~ 255min/s
Real Time Clock
Chipset integrated RTC with onboard lithium battery
Expansion
2 x MiniPCIe (support mSATA) and Card2 half-size choosable, 1 x SIM slot
Graphics
Chipset
Intel® 5th/4th Gen integrated HD Graphics
Display Interface
1 x HDMI/DVI-D, 1 x DisplayPort/DVI-D, 1 x LVDS
LAN
Chip
1 x Intel® I210-AT Gigabit LAN 1 x Intel® I218-LM Gigabit LAN (Support iAMT10.0)
I/O
Serial ATA
2 x SATA3 support RAID 0, 1
Audio
Realtek ALC888 HD Audio
Digital I/O
Programmable 8-bit GPIO with 12 pin-header
Internal I/O
2 x SATA3, 1 x RS232/422/485, 4 x RS232, 1 x PS/2, 4 x USB2.0, 1 x LVDS, 1 x LCD inverter, 1 x LPC, 1 x SMBUS, 1 x DIO, 1 x Audio, 1 x DC Out
Rear I/O
1 x RS232, 1 x HDMI/DVI-D, 1 x DisplayPort/DVI-D, 2 x USB3.0, 2 x LAN
Mechanical & Environmental
Power Requirement
DC input 9~24V
Size & Thickness
146mm x 101mm (L x W), 1.6mm
Temperature
Operating within C~60°C (3F~140°F) Storage within -20°C~80°C (-4°F~176°F)
Relative Humidity
10%~90%, non-condensing

1.2 <Product Specification>

Page 7
LE-37E Users Manual
-6-

1.3 <Mechanical Drawing>

Page 8
LE-37E Users Manual
-7-
CPU
5th/4th
Gen Processor
PCH-LP
DDR3L
SO-DIMM
1 x DisplayPort
PTN3460
1 x LVDS
SIO
NCT6106D
DDI
Channel A
eDP
2 x SATA3
SATA3
2 x USB3.0
4 x USB2.0
USB3.0
USB2.0
SPI Flash
SPI
PCIe x1
I218-LM
HDA
HD Audio
PCIe x1
SATA3
LPC
1 x LPC
ALC888
5 x RS232
1 x SMBUS
1 x PS/2
I210-AT
PCIe x1
MiniCard1
SATA3
PCIe x1
MiniCard2
1 x RS232/422/485
1 x DIO
1 x DVI-D
SMBUS
GPIO
1 x HDMI
DDI
1 x DVI-D

1.4 <Block Diagram>

Page 9
LE-37E Users Manual
-8-
CN_LVDS
MINI_CARD1
CN_LPC
CN_AUDIO
DC_IN
CN_USB1
CN_PS2
JFRNT
SATA3-2
CN_COM5/6
CN_INV
DC_OUT
SYSFAN
CPUFAN
SMBUS
MINI_CARD2
CN_COM3/4
CN_COM2
CN_DIO
SO-DIMM
CN_PS2
SATA3-1
CN_USB2
COM1
HDMI/CN_DVI1
DisplayPort
LAN1
LAN2
USB
CN_DVI2
SIMM

Chapter 2 <Hardware setup>

2.1 <Connector Location and Reference>

Page 10
LE-37E Users Manual
-9-
Connector
Function
SO-DIMM
204-pin DDR3L SO-DIMM slot
SATA3-1/2
7-pin Serial ATA3 connector
CN_AUDIO
5 x 2-pin audio pin header
CN_LPC
6 x 2-pin LPC pin header
CN_DIO
6 x 2-pin LPC pin header
CN_LVDS
20 x 2-pin LVDS connector
CN_INV
5-pin LCD inverter connector
CN_DVI1
10 x 2-pin DVI connector
CN_DVI2
10 x 2-pin DVI connector
CN_COM2
10-pin RS232/422/485 connector
CN_COM3/4
20-pin RS232 connector
CN_COM5/6
20-pin RS232 connector
CN_USB1/2
5 x 2-pin USB2.0 pin header
CN_PS2
5 x 2-pin PS/2 pin header
SMBUS
5-pin SMBus connector
SIMM
6-pin SIM card slot
CPUFAN
4-pin CPU fan connector
SYSFAN
4-pin system fan connector
JFRNT
5 x 2-pin front panel switch/indicator pin header
MINI_CARD1/2
52-pin MiniPCIe card slot
DC_OUT
4-pin SATA Power connector
DC_IN
4-pin ATX12V power connector
Connector
Function
COM1
DB9 connector
DisplayPort
DisplayPort connector
HDMI
HDMI connector
USB
2 x USB3.0 connector
LAN1
RJ45 connector
LAN2
RJ45 connector

2.1.1 <Internal connectors list>

2.1.2 <External connectors list>

Page 11
LE-37E Users Manual
-10-
Jumper
Function
JAT
Power mode select
JRTC
CMOS Normal/Clear Setting
JVLCD
Panel Voltage Setting
JMSATA1/2
MiniCard1/2 mSATA Setting
JCSEL1/2
CN_COM2 RS232/422/485 select
JP1/2
COM1 and CN_COM2 9-pin setting
Jumper settings
Function
1-2
Clear CMOS
2-3
Normal (Default)
Jumper settings
Function
1-2
AT mode
2-3
ATX mode (Default)
JRTC
JVLCD
JMSATA2
JAT
JMSATA1
JP2
JP1
JCSEL1
JCSEL2

2.2 <Jumper Location and Reference>

2.2.1 <Jumper list>

2.2.2 <Clear CMOS and Power on type selection>

JRTC: Clear CMOS data jumper
JAT: AT/ATX mode select jumper
Page 12
LE-37E Users Manual
-11-
Key
Mounting notch
Press down
Latch

2.3 <Installing the Memory>

In the process, the board must be powered off.
1. Put the memory tilt into the slot. Note the Memory notch key aligned slot key.
2. Then press down till lock into the mounting notch.
3. To remove the memory, push outward on both sides of the latch.
Page 13
LE-37E Users Manual
-12-
I218-LM
SATA3-1
SATA3-2
I210-AT

2.4 <I/O interface>

2.4.1 <Serial ATA interface>

Support RAID0 and 1.

2.4.2 <Ethernet interface>

The board provide I210-AT and I218-LM Gigabit Ethernet which supports WOL on
rear I/O.
It supports Intel® AMT 10.0 feature.
(Note that the CPU must support vPro technology, ex:
i7-5650U)
Page 14
LE-37E Users Manual
-13-
Pin
Signal
Pin
Signal
1
5V 2 NC
3
HPD
4
GND
5
TMDS_TX0-
6
TMDS_TX0+
7
GND
8
TMDS_TX1-
9
TMDS_TX1+
10
GND
11
TMDS_TX2-
12
TMDS_TX2+
13
GND
14
TMDS_CLK-
15
TMDS_CLK+
16
GND
17
SDA
18
SCL
19
NC
20
NC
CN_DVI2
DisplayPort
CN_LVDS
1
40
JVLCD
2
39
2
1
20
19
1
2
HDMI/CN_DVI1
5
6

2.4.3 <Display interface>

Based on the 5th/4th Gen CPU with built-in HD Graphics, the DisplayPort up to
3840x2160 @ 60Hz, the HDMI resolution up to 2560x1600 @ 60Hz and LVDS
(PTN3460) up to 1920x1200 @ 60Hz support 18/24-bit color depth and dual
channel.
The built-in HD Graphics support triple display function with clone mode and
extended mode.
Note: HDMI connector can change like CN_DVI2 pin-header.
CN_DVI1/2: DVI 20-pin connector
Page 15
LE-37E Users Manual
-14-
Pin
Signal
Pin
Signal
2
Set by JVLCD
1
Set by JVLCD
4
Detect (Active low)
3
GND
6
A_LVDS_0-
5
B_LVDS_0-
8
A_LVDS_0+
7
B_LVDS_0+
10
GND
9
GND
12
A_LVDS_1-
11
B_LVDS_1-
14
A_LVDS_1+
13
B_LVDS_1+
16
GND
15
GND
18
A_LVDS_2-
17
B_LVDS_2-
20
A_LVDS_2+
19
B_LVDS_2+
22
GND
21
GND
24
A_LVDS_CLK-
23
B_LVDS_3-
26
A_LVDS_CLK+
25
B_LVDS_3+
28
GND
27
GND
30
A_LVDS_3-
29
B_LVDS_CLK-
32
A_LVDS_3+
31
B_LVDS_CLK+
34
GND
33
GND
36
LVDS_DDCSCL
35
NC
38
LVDS_DDCSDA
37
NC
40
NC
39
NC
Pin
Signal
1
12V
2
Backlight Control
3
Reserve
4
GND
5
Enable Backlight
Jumper settings
Function
1-2
3.3V (Default)
3-4
5V
5-6
12V
CN_LVDS: LVDS 40-pin connector (Model: HIROSE DF13-40DP-1.25V compatible)
Note: Pin4 only need to be connected to GND
CN_INV: LVDS 5-pin Backlight power connector
JVLCD: LVDS panel power select jumper
Effective patterns of connection: 1-2 / 3-4 / 5-6
Other may cause damage
Page 16
LE-37E Users Manual
-15-
Pin
Signal
Pin
Signal
1
DCD
2
RXD
3
TXD
4
DTR
5
GND
6
DSR
7
RTS
8
CTS
9
Set by JP2
10
Key
Pin
Signal
Pin
Signal
1
DCD/ 422TX-/ 485-
2
RXD/ 422TX+/ 485+
3
TXD/ 422RX+
4
DTR/ 422RX-
5
GND
6
DSR
7
RTS
8
CTS
9
Set by JP1
10
Key
CN_COM2
1
2
9
10
CN_COM3/4
CN_COM5/6
1
2
19
20
1
2
20
19
2 1 6
5
JP1
JP2
2
6
1
5
JCSEL1
1
2
11
12
JCSEL2
1
2
5
6
COM1

2.4.4 <Serial Port interface>

COM1: RS232 DB9 connector
CN_COM2: RS232/422/485 10-pin header (Pitch 1.27mm x 2.54mm)
Use JCSEL1 and JCSEL2 to select communication mode
Page 17
LE-37E Users Manual
-16-
Pin
Signal
Pin
Signal
1
DCD1
2
RXD1
3
TXD1
4
DTR1
5
GND
6
DSR1
7
RTS1
8
CTS1
9
RI1
10
NC
11
DCD2
12
RXD2
13
TXD2
14
DTR2
15
GND
16
DSR2
17
RTS2
18
CTS2
19
RI2
20
Key
Jumper settings
Function
1-2
5V
3-4
12V
5-6
RI (Default)
Function
JCSEL1
JCSEL2
RS232
RS485
RS422
1
12
1
12
1
12
6
1
5
1
5
1
2
11
2
11
2
11
2
2
2
5
6
6
COM3/4,5/6: RS232 20-pin header (Pitch 1.27mm x 2.54mm)
JP1, JP2: COM1, COM2 pin-9 setting
Effective patterns of connection: 1-2 / 3-4 / 5-6
Other may cause damage
JCSEL1, JCSEL2: For configure COM2 communication mode
Page 18
LE-37E Users Manual
-17-
Pin
Signal
Pin
Signal
1
5VSB
2
5VSB
3
DATA0-
4
DATA1-
5
DATA0+
6
DATA1+
7
GND
8
GND
9
GND
10
Key
CN_AUDIO
1
10
CN_USB1
1
10 2 2
9
USB3.0
9
CN_USB2
1 2 9
10

2.4.5 <USB interface>

CN_USB1/2: Front panel USB2.0 10-pin header (Pitch 2.54mm)

2.4.6 <Audio interface>

Page 19
LE-37E Users Manual
-18-
Pin
Signal
Pin
Signal
1
MIC_L
2
GND
3
MIC_R
4
NC
5
FP_OUT_R
6
MIC_DETECT
7
SENSE
8
Key
9
FP_OUT_L
10
FP_OUT_DETECT
Jumper settings
Function
1-2
Support mSATA
2-3
Normal operation (Default)
MINI_CARD1
JMSATA1
MINI_CARD2
1
3
1
3
JMSATA2
CN_AUDIO: Front panel audio 10-pin header (Pitch 1.27mm x 2.54mm)

2.4.7 <Expansion slot>

MINI_CARD2 have some special design to compatible our MiniPCIe card (ex:
MPX-574D2, MPX-210D2 etc) and MINI_CARD1/2 supports mSATA set by
JMSATA1/2.
MINI_CARD1 supports SIM card to use 3G module.
JMSATA1/2: Setting MINI_CARD1/2 to support PCIe/mSATA
Page 20
LE-37E Users Manual
-19-
Pin
Signal
Pin
Signal
1
Power_ON-
2
Power_ON+
3
Speaker-
4
Speaker+
5
HDD_LED-
6
HDD_LED+
7
Power_LED-
8
Power_LED+
9
Reset+
10
Reset-
JFRNT
10
CN_DIO
1
12
1
9
2
11
2
CN_LPC
1
11
12
2
SMBUS
1
5
CPUFAN
1
4
SYSFAN
1
4

2.4.8 <Front panel switch and indicator>

JFRNT: Front panel switch and indicator 14-pin header (Pitch 2.54mm)

2.4.9 <Other interface>

Page 21
LE-37E Users Manual
-20-
Parameter
SYM
MIN
TYP
MAX
UNIT
Conditions
Input Low Voltage
VIL
0.8
V
Input High Voltage
VIH
2.0
V
Output Low Voltage
VOL
0.4
V
IOL =12mA
Input High Leakage
I
LIH
+10
μA
VIN =3.3V
Input Low Leakage
I
LIL
-10
μA
VIN =0V
Pin
Signal
Pin
Signal
1
GND
2
GND
3
GPIO0
4
GPIO4
5
GPIO1
6
GPIO5
7
GPIO2
8
GPIO6
9
GPIO3
10
GPIO7
11
5V
12
12V
Pin
Signal
Pin
Signal
1
CLK
2
RST
3
-LFRAME
4
LAD3
5
LAD2
6
LAD1
7
LAD0
8
3.3V
9
SERIRQ
10
GND
11
3.3VSB
12
NC
When using GPIO function, please note:
As Output:
Open-drain, most applications need use an external pull up
resistor. (If not may cause damage)
As Input: TTL-level.
GPIO DC characteristics
CN_DIO: GPIO 12-pin header (Pitch 2.00mm)
CN_LPC: LPC 12-pin header (Pitch 2.00mm)
CN_LPC support TPM module.
Page 22
LE-37E Users Manual
-21-
Pin
Signal
1
5V
2
NC
3
SMBDAT
4
SMBCLK
5
GND
Pin 1 2 3 4
Signal
GND
12V
Sensor
Control
Pin 1 2 3 4
Signal
GND
12V
Sensor
Control
Pin
Signal
Pin
Signal
1
GND
2
GND
3
9~24V Power input
4
9~24V Power input
DC_IN
1 2 3
4
SMBUS: SMBus 5-pin connector
CPUFAN: CPU cooler fan 4-pin connector
SYSFAN: System cooler fan 4-pin connector

2.5 <Power supply>

2.5.1 <Power input>

DC_IN: ATX12V 4-pin power connector
Page 23
LE-37E Users Manual
-22-
Pin
Signal
1
12V
2
GND
3
GND
4
5V
DC_OUT
1
4

2.5.2 <Power output>

DC_OUT: SATA power 4-pin connector
Page 24
LE-37E Users Manual
-23-

Appendix A <Flash BIOS>

A.1 <Flash tool>
The board is based on Phoenix BIOS and can be updated easily by the BIOS
auto flash tool. You can download the tool online at the address below:
http://www.commell.com.tw/Download/BIOS/FPT10.rar
The tools file name is fpt.exe, its the utility that can write the data into the
BIOS flash chip and update the BIOS.
A.2 <Flash BIOS process>
1. Please make a bootable UFD which can boot into DOS enviroment.
2. Unzip the flash tool and copy it into bootable UFD.
3. Add a bin file to the same folder..
4. Power on the system and flash the BIOS under the DOS environment.
(Command: fpt savemac f xxx.bin)
5. Power off the system and then power on.
Page 25
LE-37E Users Manual
-24-

Appendix B <Installation driver Notes>

B.1 <iAMT(ME) driver>
Before installing, it need to install Microsoft Hotfix KB2685611 first for Win7
32/64 bit. More information please refer
https://www.microsoft.com/en-us/download/details.aspx?id=38423
B.2 <USB3.0 driver>
Before Win7 install the USB3.0 driver or use in Win8 and Win8.1, xHCI
needs to be enabled in the BIOS.
Note that if enable xHCI, all USB port will unusable in Win7. So first need
copy driver folder to your HDD, then enable xHCI, and use PS/2 to do install.
The path is X:\Driver\USB3.0\Intel_USB_3.0_xHC_Driver_4.0.0.27_PV
Advanced > South Bridge Configuration > SB USB Config > xHCI Mode
Page 26
LE-37E Users Manual
-25-
BIOS panel type selection form (BIOS Version:1.0)
Single / Dual channel
Single / Dual channel
NO.
Type
NO.
Type
1
640 x 480
9
1600 x 1050
2
800 x 600
10
1920 x 1200
3
1024 x 768
11
Reserved
4
1280 x 1024
12
Reserved
5
1400 x 1050 Reduced Blanking
13
Reserved
6
1400 x 1050 non-Reduced Blanking
14
Reserved
7
1600 x 1200
15
Reserved
8
1200 x 768
16
Reserved

Appendix C <LCD Panel Type select>

According your panel, it need to select the correct resolution in the BIOS. If there is
no fit your panel type, please feedback for us to make OEM modol.
Page 27
LE-37E Users Manual
-26-
GPIO
0 1 2 3 4 5 6
7
bit 0 1 2 3 4 5
6
7

Appendix D <Programmable GPIO >

The GPIO can be programmed with the MS-DOS debug program using simple
IN/OUT commands.
The DC characteristics please refer to GPIO paragraph (Page25).
-o 4E 87 ;enter configuration
-o 4E 87
-o 4E 07
-o 4F 07 ;select Logical Device
-o 4E 30
-o 4F 10 ;activate GPIO function (The board use GPIO3)
-o 4E F0
-o 4F XX ;set 01 GPIO as input, set 00 GPIO as output
-o 4E F1
-o 4F XX ;if set GPIO as output, this registers value can be set 00~ FF
Optional
-o 4E F2
-o 4F XX ;set 01, the respective bit are inverted (Both input and output)
;set 00, the respective bit are normal
For further information, please refer to Nuvoton NCT6102D datasheet
Page 28
LE-37E Users Manual
-27-

Appendix E <Programmable Watch Dog Timer>

Timeout value range
1 to 255 Minute and Second
Program sample
Watchdog timer setup as system reset with 5 second of timeout
-o 4E 87 ;enter configuration
-o 4E 87
-o 4E 07
-o 4F 08 ;select Logical Device
-o 4E 30
-o 4F 01 ; activate WDTO# function
-o 4E F5
-o 4F 00 ;set 00 is second mode, set 04 is minute mode
-o 4E F6
-o 4F 05 ;00h: Timeout Disable
;01h: Timeout occurs after 1 minute only
;02h: Timeout occurs after 2 second/minute
;03h: Timeout occurs after 3 second/minute
;FFh: Timeout occurs after 255 second/minute
(The deviation is approx 1 second.)
For further information, please refer to Nuvoton NCT6102D datasheet
Page 29
LE-37E Users Manual
-28-
Address
19F., NO.94, Sec. 1, Xintai 5th Rd., Xizhi Dist., New Taipei
City 22102, Taiwan.
TEL
+886-2-26963909
FAX
+886-2-26963911
Website
www.commell.com.tw
E-mail
info@commell.com.tw (General infomation)
tech@commell.com.tw (Technical Support)

Contact information

Any advice or comment about our products and service, or anything we can help
you please dont hesitate to contact with us. We will do our best to support you for
your products, projects and business.
Taiwan Commate computer Inc.
Commell is a brand name of Taiwan Commate computer Inc.
Loading...