COMMELL LE-37D User Manual

LE-37D

3.5 inch Motherboard

User’s Manual

Edition 1.66

2015/06/26

1

Copyright

Copyright 2014, all rights reserved. This document is copyrighted and all rights are
reserved. The information in this document is subject to change without prior notice t o
make improvements to the products.
This document contains proprietary information and pr otected by copyright. No part of
this document may be reproduced, copied, or translated in any form or any means
without prior written permission of the manufacturer.
All trademarks and/or registered trademarks contains in this document are property of
their respective owners.

Disclaimer

The company shall not be liable for any incidental or consequenti al damages resulting
from the performance or use of this product.
The company does not issue a warranty of any kind, express or implied, including
without limitation implied warranties of merchantability or fitness for a particular
purpose.
The company has the right to revise the manual or include changes in the specifications
of the product described within it at any time without notice and without obli gation to
notify any person of such revision or changes.

Trademark

All trademarks are the property of their respective holders.

Any questions please visit our website at TUhttp://www.commell.com.twUT

Packing List:

Please check the package content before you starting using the board.

Hardware:

LE-37D 3.5 inch Miniboard x 1 (include Cooler Fan)

Cable Kit:

SATA Cable x 1
(OALSATA3-L)/

(1040529)

COM Port Cable x 1
(OALES-BKU1NB)/ (1040086)

2

1 to 3 power output cable x 1

(OAL4P-2)/ (1040051)

DC Power Cable x 1
(OALDC-A)/ (1040433)

SATA Power Cable x 1
(OAL4P-S2)/ (1040054)

Audio Cable x 1
(OALPJ-HDUNB)/ (1040123)

PS/2 Keyboard & Mouse Cable x 1

(OALPS2/KM)/ (1040131)

CRT cable without bracket x 1

(OALVGA-SNB-7)/ (1040557)

USB2.0 Cable x 1
(OALUSBA-3)/ (1040173)

Printed Matters:

Driver CD (Including User’s Manual) x 1

Cooler: Heat Sink:

(OHSF-5) / (2181010016) (OHS-7) / (2181110009)

LE-37DJIP, LE-37DJX2,
LE-37DEIP, LE-37DEX2

LE-37DNIP, LE-37DNX2

3

Index

Chapter 1 <Introduction> ..............................................................................5

1.1 <Product Overview>.....................................................................................5

1.2 <Product Specification>................................................................................6

1.3 <Mechanical Drawing>.................................................................................8

1.4 <Block Diagram>..........................................................................................9

Chapter 2 <Hardware Setup>......................................................................10

2.1 <Connector Location>................................................................................10

2.2 <Jumper Location & Reference>................................................................10

2.3 <Connector Reference>............................................................................. 11

2.3.1 <Internal Connectors> ................................................................... 11

2.3.2 <External Connectors>.................................................................. 11

2.4 <Memory and CFAST Setup>.................................................................... 11

2.4.1 < Memory Setup > ......................................................................... 11

2.4.2 < CFAST Setup >...........................................................................12

2.5 <CMOS & ATX Setup>...............................................................................13

2.6 <Serial ATA Interface>................................................................................14

2.7 <Ethernet Interface>...................................................................................14

2.8 <Onboard Display Interface>......................................................................14

2.8.1 <External Display>.........................................................................14

2.8.2 <Internal Display>..........................................................................14

2.9 <Integrated Audio Interface>...................................................................... 19

2.10 <USB Interface>.......................................................................................19

2.11 <Serial Port>.............................................................................................22

2.12 <PCIe Mini Card and SIM Interface>........................................................ 24

2.12.1 <SIM Setup>................................................................................25

2.13 <GPIO and SMBUS Interface>.................................................................27

2.14 <Power Supply and Fan Interface >.........................................................28

2.14.1 <Power Input>..............................................................................28

2.14.2 <Power Output>........................................................................... 28

4

2.14.3 <Fan connector>..........................................................................29

2.15 <Switch and Indicator>.............................................................................30

Chapter 3 <System Setup> .........................................................................30

3.1 <Audio Configuration>................................................................................ 30

3.2 <Display Properties Setting>......................................................................31

3.3 <SATA configuration>.................................................................................33

Chapter 4 <BIOS Setup> .............................................................................34

Appendix A <I/O Port Pin Assignment>..................................................... 35

A.1 <Serial ATA Port>.......................................................................................35

A.2 <LAN Port>................................................................................................35

A.3 <LPC Port>................................................................................................35

Appendix B <Flash BIOS> ..........................................................................36

B.1 <Flash Tool> ..............................................................................................36

B.2 <Flash BIOS Procedure>...........................................................................36

Appendix C <Programming GPIO’s> .........................................................37

Appendix D < Programming Watchdog Timer >.......................................38

Contact Information..................................................................................... 39

Chapter 1 <Introduction>

1.1 <Product Overview>

The LE-37D motherboard is design based on Intel® Celeron® Processor J1900 / N2930
and Intel® Atom Processor E3845, delivering outstanding compute, graphical, and
media performance while operating in an extended range of thermal conditions. The
SoC bases on the Silvermont microarchitecture, utilizing Intel’s industry-leading 22nm
process technology with 3-D Tri-Gate transistors, which deliver significant
improvements in computational performance and energy efficiency.

New features for Intel® Celeron® and Atom Processor

The Intel® Celeron® Processor J1900 / N2930 and Intel® Atom E3845 Processor

5

supports graphics, media performance, flexibility and more enhanced security that is

suitable for a variety of intelligent systems the ideal choice.

Outstanding integration of I/O interfaces

Supports display interfaces with graphics processing, camera interfaces with image
processing, audio with digital signal processing, multiple storage types, an d leg acy
embedded I/O. Provides interface expansion capabilities through industry-standard
high-bandwidth interfaces such as PCI Express* Gen 2.0, Hi-speed USB 2.0, and USB

3.0 connectivity.

All in One multimedia solution

Based on Intel® J1900 / N2920 /E3845 SoC, the board provides high performance
onboard graphics, CRT, 24-bit dual channel LVDS interface, Display Port, DVI and 2
channels High Definition Audio, to meet the very requirement of the multimedia
application.

Flexible Extension Interface

The board provides two PCIe mini slot and one SIM slot.

1.2 <Product Specification>

General Specification

Form Factor 3.5 inch motherboard
CPU Intel® Processor J1900/N2930/E3845, package type FCBGA1170
Memory 1 x DDR3L (support 1.35V) 1066/1333 SO-DIMM up to 8GB
Real Time Clock Chipset integrated RTC with onboard lithium battery
Watchdog Timer Generates a system reset with internal timer for 1min/s ~ 255min/s

Power
Management
Serial ATA(SATA)
Interface

VGA Interface Intel® Clear Video integrated HD Graphics Technology
DVI Interface Onboard DVI connector.

Display port
Interface

Supports ACPI 5.0 compliant

1 x serial ATA interface with 300MB/s(3Gb/s) transfer rate

(DVI and LVDS1 can’t be enabled simultaneously)

Onboard Display port connector.

(Display port and LVDS2 can’t be enabled simultaneously)

6

LVDS Interface 2 x Onboard 24-bit dual channel LVDS connector with

+3.3V/+5V/+12V supply

Audio Interface Realtek ALC262 High Definition Audio Codec
LAN Interface 2 x Intel® I210-AT Gigabit LAN
GPIO Interface Onboard programmable 8-bit Digital I/O interface.

Extended
Interface

Internal I/O Port 4 x RS232, 1 x RS232/422/485, 1 x GPIO, 1 x Audio connector, 1 x

External I/O Port 1 x RS232, 1 x DVI port, 1 x Display port, 2 x RJ45 LAN ports, 1 x

Power
Requirement

Dimension 146mm x 101mm

Temperature

Ordering Code

LE-37DJIP Intel Celeron Processor J1900 (2M Cache, 2.42GHz), DVI, Display Port,

LE-37DNIP Intel Celeron Processor N2930 (2M Cache, 2.16GHz), DVI, Display Port,

LE-37DEIP Intel Atom Processor E3845 (2M Cache, 1.91GHz), DVI, Display Port,

LE-37DJX2 Intel Celeron Processor J1900 (2M Cache, 2.42GHz), 2 x LVDS, CRT,

LE-37DNX2 Intel Celeron Processor N2930 (2M Cache, 2.16GHz), 2 x LVDS, CRT,

LE-37DEX2 Intel Atom Processor E3845 (2M Cache, 1.91GHz), 2 x LVD S , CRT,

The specifications may be different as the actual production.
For further product information please visit the website at http://www.commell.com.tw

2 x PCIE Mini card(1 x mSATA option), 1 x SIM socket, 1x CFast

(CFast and mSATA can’t be enabled simultaneously)

SMBUS connector, 1 x CRT, 2 x LVDS, 1 x LPC, 4 x USB 2.0(XHCI)
and 1 x SATAII

USB 3.0(XHCI)/2.0(EHCI) port, 1 x USB 2.0 ports(EHCI).
6~27V full range DC Input

Operating within 0~60 centigrade(forLE-37DJ andLE-37DN serial)
Storage within -20~85 centigrade. (forLE-37DJ andLE-37DN serial)

Operating within -40~85 centigrade(for LE-37DE serial)
Storage within -40~85 centigrade.(for LE-37DE serial)

CRT, Gigabit LAN, USB3.0 & 2.0, Serial Port, SATAII, Audio, PCIE Mini
card, SMBUS, GPIO, SIM, LPC, mSATA
,CFast

CRT, Gigabit LAN, USB3.0 & 2.0, Serial Port, SATAII, Audio, PCIE Mini
card, SMBUS, GPIO, SIM, LPC, mSATA, CFast

CRT, Gigabit LAN, USB3.0 & 2.0, Serial Port, SATAII, Audio, PCIE Mini
card, SMBUS, GPIO, SIM, LPC, mSATA, CFast

Gigabit LAN, USB3.0 & 2.0, Serial Port, SATAII, Audio, PCIE Mini card,
SMBUS, GPIO, SIM, LPC, mSATA, CFast

Gigabit LAN, USB3.0 & 2.0, Serial Port, SATAII, Audio, PCIE Mini card,
SMBUS, GPIO, SIM, LPC, mSATA, CFast

Gigabit LAN, USB3.0 & 2.0, Serial Port, SATAII, Audio, PCIE Mini card,
SMBUS, GPIO, SIM, LPC, mSATA, CFast

7

1.3 <Mechanical Drawing>

8

1.4 <Block Diagram>

9

Chapter 2 <Hardware Setup>

2.1 <Connector Location>

2.2 <Jumper Location & Reference>

Jumper Function

JRTC CMOS Operating/Clear Setting
JVLCD Panel Voltage Setting
JAT Power mode select
JP1 Com1 Voltage Setting (For Pin 9)
JP2 Com2 Voltage Setting (For Pin 9)

JCSEL1
JCSEL2

JVUSB1
JMSATA

CN_COM2 RS-232 RS422 RS485 Setting
CN_IR Setting
USB Voltage Setting
Mini Card1 mSATA Setting (Mini PCIe)

10

2.3 <Connector Reference>

2.3.1 <Internal Connectors>

Connector Function Remark

CPU FCBGA 1170 CPU
SO-DIMM 204 -pin DDR3L SO-DIMM slot
SATA 7-pin Serial ATA2 connector
DC_IN DC 6~27V input connector
DC_OUT 4-pin DC output connector
CN_AUDIO 5 x 2-pin audio connector
CN_DIO 6 x 2-pin digital I/O connector
CN_USB 2/3 5 x 2-pin USB2.0 connector
CN_CRT 8 x 2-pin CRT connector
CN_LVDS1/2 20 x 2-pin LVDS connector
CN_INV1/2 5-pin LCD inverter connector
CN_COM2 9-pin RS232/485/422 connector
CN_COM 3/4 5/6 19-pin RS232 connector
CN_LPC 6 x 2-pin LPC connector
CN_PS2 5 x 2-pin PS2 connector
CN_SMBUS 5-pin SMBUS connector
JFRNT 10-pin front panel switch/indicator connector
Mini-Card1/2 52-pin Mini-PCIe slot
SIMM 6-pin slot
CFAST 7+17-pin connector
CPUFAN 4-pin CPU cooler fan connector
SYSFAN 4-pin System cooler fan con nector

2.3.2 <External Connectors>

Connector Function Remark

COM1 DB9 Serial port connector
DisplayPort 20-pin DisplayPort connector
DVI 19-pin DVI connector
USB USB 2.0 and USB 3.0 connector
RJ45 1/2 RJ45 LAN connector

2.4 <Memory and CFAST Setup>

2.4.1 < Memory Setup >

The board provide 204-pin DDR3L SO-DIMM to support 1066/1333MHz up to 8GB.

11

Support Non-ECC, unbuffered memory only

SO-DIMM

2.4.2 < CFAST Setup >

The board provide one CFAST slot which supports SATA2 interface.
The CFAST has the same size with CF card, but it shows higher efficiency and stability
to transmit SATA signal.

CFAST plug closeup

Installing the CFAST in the back of the board.

Note that the slot direction and fool-proofing

Installation is complete

12

2.5 <CMOS & ATX Setup>

The board’s data of CMOS can be setting in BIOS. If the board refuses to boot due to
inappropriate CMOS settings, here is how to proceed to clear (reset) the CMOS to its
default values.

Jumper: JRTC
Type: Onboard 3-pin jumper

JRTC Mode

1-2 Clear CMOS
2-3 Normal Operation

Default setting: 2-3

Jumper: JAT
Type: Onboard 3-pin jumper

JAT Mode

1-2 AT Mode
2-3 ATX Mode

Default setting:2-3

13

2.6 <Serial ATA Interface>

LE-37D has one SATAII interface, the transfer rate of the SATAII can be up to 300MB/s.

2.7 <Ethernet Interface>

The board integrates with two Intel® I210-AT controllers, The Intel Gigabit Ethernet
supports triple speed of 10/100/1000Base-T, with IEEE802.3 compliance.

2.8 <Onboard Display Interface>

Based on Intel CPU with built-in HD Graphic, the board provides one DVI (onboard) and
one DisplayPort, two 40-pin LVDS interface with 5-pin LCD backlight inverter connector
and internal 16-pin CRT interface.
The board provides double display function with clone mode and extended desktop
mode for DVI, DisplayPort, CRT and LVDS.

2.8.1 <External Display>

Please connect your monitor which supports DisplayPort and DVI to connect
onboard rear I/O Port.

2.8.2 <Internal Display>

The board provides two 40-pin LVDS connector for 18/24-bit single/dual channel
panels, supports up to 1920 x 1080 resolution, with one LCD backlight inverter
connector and two jumper for panel voltage setting.

Please install LVDS cable before boot up.

14

Effective patterns of connection: 1-2 / 3-4 / 5-6

Warning: others cause damages

Connector: JVLCD (LVDS1 voltage and LVDS2 voltage must be the same)
Type: 6-pin Power select Header

Pin Description

1-2 LCDVCC (3.3V)
3-4 LCDVCC (5V)
5-6 LCDVCC (12V)

Default: 1-2

15

Connector: CN_INV
Type: 5-pin LVDS Power Header

Pin Description

1 +12V
2 PWM
3 GND
4 GND
5 ENABKL

Connector: CN_LVDS
Type: onboard 40-pin connector for LVDS connector

Connector model: HIROSE DF13-40DP-1.25V or compatible

Pin Signal Pin Signal

2 LCDVCC 1 LCDVCC
4 LVDS Detect (Note) 3 GND
6 ATX0- 5 BTX0-

8 ATX0+ 7 BTX0+
10 GND 9 GND
12 ATX1- 11 BTX1­14 ATX1+ 13 BTX1+
16 GND 15 GND
18 ATX2- 17 BTX2­20 ATX2+ 19 BTX2+
22 GND 21 GND
24 ACLK- 23 BTX3­26 ACLK+ 25 BTX3+
28 GND 27 GND
30 ATX3- 29 BCLK­32 ATX3+ 31 BCLK+
34 GND 33 GND
36 DDCPCLK 35 N/C
38 DDCPDATA 37 N/C
40 N/C 39 N/C

Note: The LVDS Detect Pin please contact to the Panel GND.

To setup the LCD, you need the component below:

1. A panel with LVDS interfaces.

2. An inverter for panel’s backlight power.

3. A LCD cable and an inverter cable.

For the cables, please follow the pin assignment of the connector to make a cable, because

16

every panel has its own pin assignment, so we do not provide a standard cable; please find

a local cable manufacture to make cables.

LCD Installation Guide:

1. Preparing the LE-37D, LCD panel and the backlight inverter.

2. Please check the datasheet of the panel to see the voltage of the panel, and set
the jumper JVLCD to +12V or +5V or +3.3V.

3. You would need a LVDS type cable.

Panel side

For sample illustrator only

4. To connect all of the devices well.

Board side

After setup the devices well, you need to select the LCD panel type in the BIOS.
The panel type mapping is list below:

17

BIOS panel type selection form (BIOS Version:1.0)

Single / Dual channel Single / Dual channel

NO.

1
2
3
4
5
6
7
8

Connector: CN_CRT
Connector type: 16-pin header connector (pitch = 2.00mm)

Pin Number Assignment Pin Number Assignment

Output format

640 x 480
800 x 600

1024 x 768
1280 x 1024
1400 x 1050
1400 x 1050
1680 x 1200

1366 x 768

1 BR 2 BG
3 BB 4 NC
5 -CRTATCH 6 IOGND1
7 IOGND1 8 IOGND1

9 NC 10 -CRTATCH
11 NC 12 5VCDA
13 5HSYNC 14 5VSYNC
15 5VCLK 16 NC

NO.

9
10
11
12
13
14
15

Output format

1680 x 1050
1920 x 1200

1440 x 900
1600 x 900
1024 x 768
1280 x 800

1920 x 1080

Connector: CN_DVI
Connector type:
E&T 3950-B20C-00R or similar (HIROSE DF13-20DP-1.25V compatible)

Pin Number Assignment Pin Number Assignment

1 +5V 2 +3.3V
3 HPD 4 Ground
5 TMDSTX0N 6 TMDSTX0P
7 Ground 8 TMDSTX1N

9 TMDSTX1P 10 Ground
11 TMDSTX2N 12 TMDSTX2P
13 Ground 14 TMDSTXCN
15 TMDSTXCP 16 Ground
17 DVI_DA 18 DVI_SL
19 AUXN 20 AUXP

18

2.9 <Integrated Audio Interface>

The board provides the onboard high definition audio with Realtek ALC262

Connector: CN_AUDIO

Type: 10-pin (2 x 5) 1.27mm x 2.54mm-pitch header

Pin Description Pin Description

1 MIC_L 2 Ground
3 MIC_R 4 N/C
5 Speaker_R 6 MIC Detect
7 SENSE 8 N/C
9 Speaker_L 10 Speaker Detect

2.10 <USB Interface>

LE-37D integrates 5 x USB2.0 and 1 x USB3.0.

The specifications of USB3.0 are listed below:

The USB3.0 port need to Install USB 3.0 eXtensible Host Controller Driver and

enable xHCI Mode.

2.10.1 USB 3.0 eXtensible Host Controller Driver install

Step1. Copy the USB 3.0 driver from “Driver CD” to the local hard driver directory.

( Do not run this driver from a USB storage device)

Interface USB3.0

Controller J1900 / N2930 / E3845

Transfer Rate Up to 5Gb/s

Voltage 5V

19

Step2. Configure default BIOS, click Advanced > South Cluster Configuration > USB

Configuration, disable “EHCI Mode”.

Step3. enable “xHCI Mode” and push “F10” to save configuration. Restart your

computer.

Step4. If you enable xHCI Mode , USB 2.0 and USB 3.0 ports can’t use without

drive. We recommend that you connect PS/2 mouse / keyboard installing
USB 3.0 driver.

Step5. Double click the “Setup.exe” from the directory. Click “Next” to continue.

20

Step6. Lastly, the “Setup Complete” screen appears so click “Finish” to

restart your computer.

The specifications of USB2.0 are list

Interface USB2.0

Controller J1900 / N2930 / E3845

Transfer Rate Up to 480Mb/s

Voltage 5V

21

Connector: CN_USB 2/3
Type: 10-pin (2 x 5) header (pitch = 2.54mm)

Pin Description Pin Description

1 VCC 2 VCC
3 Data0- 4 Data1­5 Data0+ 6 Data1+
7 Ground 8 Ground
9 Ground 10 N/C

CN_USB2 need to enable xHCI Mode

2.11 <Serial Port>

The board supports one RS232 serial port and one j umper selectable RS232/422/485
serial ports. The jumper JCSEL1 & JCSEL2 can let you configure the communicating
modes for COM2.

Connector: COM1
Type: 9-pin D-sub male connector on bracket for COM1

Pin Description Pin Description

1 DCD 2 RXD
3 TXD 4 DTR
5 GND 6 DSR
7 RTS 8 CTS
9 RI 10 N/C

22

Connector: COM2

Type: 10-pin (5 x 2) 1.27mm x 2.54mm-pitch header for COM2

Function JCSEL2 JCSEL1

RS-422

RS-485

RS-232

(Default)

Setting RS-232 & RS-422 & RS-485 for COM2

Connector: COM3/4 COM5/6
Type: 19-pin (2 x 10) header pitch = 2.54x1.27mm

Pin Description Pin Description

1 DCD1 2 RXD1
3 TXD1 4 DTR1
5 GND1 6 DSR1
7 RTS1 8 CTS1
9 RI1 10 N/C
11 DCD2 12 RX2
13 TX2 14 DTR2
15 Ground 16 DSR2
17 RTS2 18 CTS2
19 RI2 20 N/C

23

Jumper: JCSEL1,JCSEL2
Type: 12-pin (6 x 2) & 8-pin (4 x 2) for set COM2 mode jumper

Power Mode JP1/2

Pin 9 with 5V Power 1-2
Pin 9 with 12V Power 3-4
Standard COM port 5-6

Default setting (5-6)

2.12 <PCIe Mini Card and SIM Interface>

The board provides two PCIe mini card slot and a SIM slot.
MINI_CARD1 is the first Mini-PCIe slot for long size Mini-PCIe cards.
MINI_CARD1 can selectively support mSATA.
MINI_CARD2 is the second Mini-PCIe slot for long size Mini-PCIe cards.
However, if you are trying to use 3G Mini-PCIe card with your SIM card, first, put your
SIM card into the slot, then put your 3G Mini-PCIe card into the MINI_CARD2.

24

Connector: SIMM (3G MiniPcie Mode)

Type: 6-pin SIM slot

Pin Description Pin Description

1 SIMVCC 2 SIMRST
3 SIMCLK 4 NC
5 GND 6 SIMVPP
7 SIMDATA

Connector: JMSATA
Type: onboard 3-pin header

JMSATA Mode

1-2 Support mSATA for MINI_CARD1
2-3 Support PCIe and USB

Default setting: 2-3

2.12.1 <SIM Setup>

Step1.

SIM card holder is marked by circle.
Slide the cap toward OPEN direction.

25

Step 2.

Make sure that the cap is now at the OPEN position.

Step 3.

Flip the cap up for inserting a SIM card into.

Step 4.

Insert a SIM card as shown in the photo.
Be sure that the corner cut is on top and the golden pads are up.

Step 5.

Now, flip down the cap as shown in the photo.

26

Step 6.

Press down and slide the cap to the CLOSE position.
Be sure that the cap is tightly held with the slot.

2.13 <GPIO and SMBUS Interface>

The board provides a programmable 8-bit digital I/O interface; you can use this general
purpose I/O port for system control like POS or KIOSK. The GPIO is an Open-drain

output and TTL-level input.

1. Output：Open-drain, Most applications need use an external pull-up resistor.

2. Input：TTL-level.

DC characteristics:

5V TTL-level Input Pin

Parameter Sym Min Typ Max Unit Conditions

Input Low Voltage VIL 0.8 V
Input High Voltage VIH 2.0 V
Input High Leakage I
Input Low Leakage I

+10 μA V

LIH

-10 μA V

LIL

= 3.3V

IN

= 0V

IN

Open-drain output pin with 12-mA sink capability

Output Low Voltage V

OL

Connector: CN_DIO
Type: 12-pin (6 x 2) header (pitch = 2.0mm)

0.4 V IOL = 12 mA

Pin Description Pin Description

1 Ground 2 Ground
3 GPIO0 4 GPIO4
5 GPIO1 6 GPIO5
7 GPIO2 8 GPIO6
9 GPIO3 10 GPIO7
11 5V 12 12V

27

Connector: CN_SMBUS
Type: 5-pin header for SMBUS Ports

Pin Description

1 VCC
2 N/C
3 SMBDATA
4 SMBCLK
5 Ground

2.14 <Power Supply and Fan Interface >

2.14.1 <Power Input>

The board requires DC input with 4-pin header, the input voltage range is from 6V to
27V.

Connector: DC_IN
Type: 4-pin DC power connector

Pin Description Pin Description

1 Ground 2 Ground
3 +6V~ +27V 4 +6V~ +27V

2.14.2 <Power Output>

Connector: DC_OUT
Type: 4-pin connector for +5V/+12V output

Pin Description Pin Description Pin Description Pin Description

1 +12V 2 Ground 3 Ground 4 +5V

Note: Maximum output current 12V/3A, 5V/3A

28

2.14.3 <Fan connector>

The board provides one 4-pin fan connecto rs supporting smart fan for CPU cooler and
system cooler.

Connector: CPUFAN
Type: 4-pin fan wafer connector

Pin Description Pin Description

1 Ground 2 +12V
3 Fan Speed Detection 4 Fan Control

Connector: SYSFAN
Type: 4-pin fan wafer connector

Pin Description Pin Description

1 Ground 2 +12V
3 Fan Speed Detection 4 Fan Control

29

2.15 <Switch and Indicator>

The JFRNT provides front control panel of the board, such as power button, reset and
beeper, etc. Please check well before you connecting the cables on the chassis.

Connector: JFRNT
Type: onboard 10-pin (2 x 5) 2.54-pitch header

Function Signal PIN Signal

Reset

Power LED

HDD LED

Speaker SPK+

Power PWRBT+

Reset- 10 9

PWRLED+ 8 7 PWRLED-

HDLED+ 6 5 HDLED-

4 3 SPK-

2 1 PWRBT-

Reset+

Chapter 3 <System Setup>

3.1 <Audio Configuration>

The board integrates REALTEK® ALC262 code. It can support 2-channel sound under
system configuration. Please follow the steps below to setup your sound system.

1. Install REALTEK HD Audio driver.

2. Lunch the control panel and Sound Effect Manager.

30

3. Select Speaker Configuration

3.2 <Display Properties Setting>

Based on Intel J1900/N2930/E3845 with HD Graphic, the board supports two DACs for
display device as different resolution and color bit.
Please install the Intel Graphic Driver before you starting setup display devices.

1. Click right button on the desktop to lunch Screen resolution > Advanced settings

31

2. Click Graphics Properties… button for more specificity setup.

Click Graphics Properties... for

advanced setup

3. This setup options can let you define each device settings.

32

3.3 <SATA configuration>

Chipset SATA Mode:

This option can let you select whether the Serial ATA hard drives would work under

33

normal IDE mode or AHCI mode

Chapter 4 <BIOS Setup>

The motherboard uses the Phoenix BIOS for the system configuration. The Phoenix
BIOS in the single board computer is a customized version of the industrial standar d
BIOS for IBM PC AT-compatible computers. It supports Intel x86 and compatible CPU
architecture based processors and computers. The BIOS provides critical low-level
support for the system central processing, memory and I/O sub-systems.

The BIOS setup program of the single board computer let the customers modify the

basic configuration setting. The settings are stored in a dedicated battery-backed
memory, NVRAM, retains the information when the power is turned off. If the battery
runs out of the power, then the settings of BIOS will come back to the default setting.

The BIOS section of the manual is subject to change without notice and is provided here

for reference purpose only. The settings and configurations of the BIOS are current at
the time of print, and therefore they may not be exactly the same as that displayed on
your screen.

To activate CMOS Setup program, press ＜DEL＞ key immediatel y after you turn on

the system. The following message “Press DEL to enter SETUP” should appear in the
lower left hand corner of your screen. When you enter the CMOS Setup Utility, the Main
Menu will be displayed as Figure 4-1. You can use arrow keys to select your function,
press ＜Enter＞ key to accept the selection and enter the sub-menu.

Figure 4-1 CMOS Setup Utility Main Screen

34

Appendix A <I/O Port Pin Assignment>

A.1 <Serial ATA Port>

Connector: SATAII
Type: 7-pin wafer connector

1 2 3 4 5 6 7

GND RSATA_TXP1 RSATA_TXN1 GND RSATA_RXN1 RSATA_RXP1 GND

7 1

A.2 <LAN Port>

Connector: RJ45
Type: RJ45 connector with LED on bracket

Pin 1 2 3 4 5 6 7 8

8 1

Description MI0+ MI0- MI1+ MI2+ MI2- MI1- MI3+ MI3-

A.3 <LPC Port>

Connector: CN_LPC
Type: 10-pin header for LPC Port

Pin Description Pin Description

1 LPC_CLK 2 RESET­3 -LFRAME 4 LAD3
5 LAD2 6 LAD1
7 LAD0 8 +3.3V
9 SERIRQ 10 Ground
11 +3.3V 12 N/C

35

Appendix B <Flash BIOS>

B.1 <Flash Tool>

The board is based on Phoenix BIOS and can be updated easily by the BIOS auto
flash tool. You can download the tool online at the address below:

http://www.commell.com.tw/Support/Product%20Technical%20Support/LE-37D.htm

The utility that can write the data into the BIOS flash ship and update the BIOS.

B.2 <Flash BIOS Procedure>

1.Extract the zip file(re-flash tool and BIOS file) to root of the USB flash
drive.

2.Insert your USB flash drive in USB port of the board and power
on the system.

3. Boot to EFI-Shell mode (UEFI Boot Enable, Legacy Boot Disable)

then input the “fs0:” command to switch to the root of the USB flash
drive.

36

4. Type the ” fpt64.efi -y -f xxx.bin” command to start flash BIOS

processes. ( xxx.bin means the BIOS file that you want to update)

5. When it finished all update processes, restart the system.

Any question about the BIOS re-flash please contact your distributors or visit the
web-site at below:

http://www.commell.com.tw/support/support.htm

UT

Appendix C <Programming GPIO’s>

The GPIO’can be programmed with the MSDOS debug program using
simple IN/OUT commands. The following lines show an example how to
do this. (The GPIO is open drain)

GPIO0…..GPIO7 bit0……bit7

-o 4E 87 ;enter configuration

-o 4E 87

-o 4E 07

-o 4F 07 ;enale GPIO function

-o 4E 30

-o 4F 10 ;enable GPIO configuration

-o 4E F0

-o 4F xx ;set GPIO as input/output; set ‘1’ for input,’0’for
output

-o 4E F1

-o 4F xx ;if set GPIO’s as output,in this register its value can
be set

Optional :

-o 4E F2

-o 4F xx ; Data inversion register ; ‘1’ inverts the current valus
of the bits ,’0’ leaves them as they are

-o 4E 30

-o 4F 01 ; active GPIO’s

37

For further information, please refer to NCT6106D datasheet.

Appendix D < Programming Watchdog Timer >

The watchdog timer makes the system auto-reset while it stops to work for a period.
The integrated watchdog timer can be setup as system reset mode by program.

Timeout Value Range

- 1 to 255

- Second or Minute

Program Sample

Watchdog timer setup as system reset with 5 second of timeout

2E, 87
2E, 87
2E, 07
2F, 08 Logical Device 8
2E, 30 Activate
2F, 01
2E, F5 Set as Second*
2F, 00
2E, F6 Set as 5
2F, 05

* Minute: bit 3 = 1; Second: bit 3 = 0

38

You can select Timer setting in the BIOS, after setting the time options, the system
will reset according to the period of your selection.

Contact Information

Any advice or comment about our products and service, or
anything we can help you please don’t hesitate to contact with us.
We will do our best to support you for your products, projects and
business.

Taiwan Commate Computer Inc.

19F., No.94, Sec. 1, Xintai 5th Rd., Xizhi Dist., New Taipei City

Address

TEL [phone]
FAX [phone]

22102, Taiwan

Website

E-Mail

Facebook

Twitter https://twitter.com/Taiwan_Commate

TUhttp://www.commell.com.twUT
[e-mail] (General Information)

[e-mail] (Technical Support)

https://www.facebook.com/pages/Taiwan-Commate-Computer-Inc/547993955271899

Commell is a brand name of Taiwan commate computer Inc.

39