Page 1
LE-365
3.5 inch Miniboard
User’s Manual
Edition 1.1
2008/10/22
Page 2
LE-365 User’s Manual
Copyright
Copyright 2008. All rights reserved. This document is copyrighted and all rights are
reserved. The information in this document is subject to change without prior notice to make
improvements to the products.
This document contains proprietary information and protect ed by copyright. No part of this
document may be reproduced, copied, or translated in any form or any means without prior
written permission of the manufacturer.
All trademarks and/or registered trademarks contains in this document are propert y of their
respective owners.
Disclaimer
The company shall not be liable for any incidental or consequenti al dam ages res ultin g from
the performance or use of this product.
The company does not issue a warranty of any kind, e xpress or implied, including without
limitation implied warranties of merchantability or fitness for a particular purpose.
The company has the right to revise the manual or include changes in th e specifications of
the product described within it at any time without notice and without obligation to notify any
person of such revision or changes.
Trademark
All trademarks are the property of their respective holders.
Any questions please visit our website at TUhttp://www.commell.com.twUT
2
Page 3
LE-365 User’s Manual
Packing List
Please check the package before you starting setup the system
Hardware:
LE-365 miniboard x 1
Cable Kit:
44-pin
44-pin
40-pin
ATA33 IDE Cable x1
DC Power Cable x 1
PS/2 Keyboard & Mouse Cable x 1
SATA Cable x 2
Audio Port Cable x 1
USB Cable x 1
1 to 3 power output cable
SATA Power Cable x 1
DVI module with bracket x1
(LE-365D Only)
COM Port Cable x 1
Printed Matters:
Driver CD x 1（including User’s Manual）
3
Page 4
LE-365 User’s Manual
Index
Chapter 1 <Introduction>................................................7
1.1 <Product Overview>.................................................................................7
1.2 <Product Specification>...........................................................................8
1.3 <Mechanical Drawing>...........................................................................10
<IO Mechanical Drawing>1.4 <Block Diagram>..........................................11
1.4 <Block Diagram>....................................................................................12
Chapter 2 <Hardware Setup>.......................................13
2.1 <Connector Location>............................................................................13
2.2 <Jumper Reference> .............................................................................15
2.3 <Connector Reference>.........................................................................16
2.3.1 <Internal Connector>..................................................................16
2.3.2 <External Connector>.................................................................16
2.4 <CPU and Memory Setup>.................................................................... 17
2.4.1< CPU>........................................................................................17
2.5 <CMOS ATX Setup>..............................................................................18
2.6 <Enhanced IDE & CF interface>............................................................19
2.7 <Serial ATA Interface>...........................................................................20
2.9.1 <Analog VGA Interface> ............................................................21
2.9.2 <Digital Display>.........................................................................22
2.9.3 <DVI Interface > .........................................................................26
2.10 <Onboard Audio Interface>..................................................................27
2.11 <USB2.0 Interface>..............................................................................28
2.12 <GPIO Interface>.................................................................................30
2.13 <Serial Port Jumper Setting >..............................................................31
2.15.1 <Power Input>..........................................................................33
Remark: DC input voltage range 8~24V..................................................33
2.14.2 <Power Output> .......................................................................34
2.14.3 <Fan Connector>....................................................................34
4
Page 5
LE-365 User’s Manual
2.15 <Indicator and Switch>.........................................................................35
Chapter 3 <System Setup>...........................................37
3.1 <Display Configuration>.........................................................................37
Chapter 4 <BIOS Setup>...............................................40
Appendix A <I/O Port Pin Assignment>......................42
A.1 <IrDA Port>............................................................................................42
A.2 < CRT Port >..........................................................................................42
A.3 <Serial ATA Port>..................................................................................42
A.4 <Serial Port>..........................................................................................43
A.5 <LAN Port>............................................................................................43
Appendix B <Flash BIOS>............................................44
B.1 BIOS Auto Flash Tool .....................................................................44
B.2 Flash Method...................................................................................44
Appendix C <System Resources>...............................45
Appendix D <Programming GPIO’s>...........................49
Contact Information......................................................50
5
Page 6
LE-365 User’s Manual
(The Page is Left For Blank)
6
Page 7
LE-365 User’s Manual Introduction
Chapter 1 <Introduction>
1.1 <Product Overview>
LE-365 is the 3.5 inches embedded miniboard based on VIA CX700M platform, with
onboard VIA Eden 1G processor, VGA, LAN, Audio, USB2.0, CF, LVDS. The board provides
economic fanless solution for multimedia applications.
VIA CX700M Chipset
The board integrates VIA CX700M, to provide built-in UniChrome Pro 3D / 2D Graphics with
MPEGII/MPEG4 decoder, and supports DDR400/533 memory up to 1G of capacity. The
CX700M has Ultra V-Link Host interface with 1 GB/sec total bandwidth to enhance the
system performance.
18/24-bit LVDS LCD interface
The board provides onboard 18/24-bit LVDS LCD interface, supports up to 1600 x 1200 of
UXGA high resolution.
Flexible Extension Interface
The board also provides Compact Flash Type II socket and two mini-PCI socket.
Product Overview
7
Page 8
LE-365 User’s Manual Introduction
1.2 <Product Specification>
General Specification
Form Factor 3.5 inches embedded miniboard
CPU Embedded VIA V4 Eden 1G processor
Front side bus: 400MHz
Fanless with heatsink only
Memory 1 x 200-pin DDR2 400/533 SO-DIMM SDRAM up to 1GB
Unbufferred, none-ECC memory supported only
Chipset VIA CX700M
BIOS Phoenix-Award v6.00PG 4Mb PnP flash BIOS
Green Function Power saving mode includes doze, standby and suspend modes.
ACPI version 1.0 and APM version 1.2 compliant
Watchdog Timer System reset programmable watchdog timer with 1 ~ 255
sec./min. of timeout value
Real Time Clock CX700M integrated RTC with lithium battery
Enhanced IDE Enhanced UltraDMA133 IDE interface supports dual channels
and up to 2 ATAPI devices
One 44-pin IDE port onboard
Serial ATA CX700M integrates 2 Serial ATA interfaces
(No RAID Function)
Up to 300MB/s of transfer rate
Multi-I/O Port
Chipset VIA CX700M with Winbond® W83697HG controller
Serial Port One RS-232/422/485 serial port
USB Port Two external & two internal Hi-Speed USB 2.0 ports with
480Mbps of transfer rate
IrDA Port One IrDA compliant Infrared interface supports SIR
K/B & Mouse PS/2 keyboard and mouse port
GPIO One 12-pin Digital I/O connector with 8-bit programmable I/O
interface
VGA Display Interface
Chipset VIA CX700M built-in S3 Graphics UniChrome Pro IGP graphics
core
Core Frequency 200MHz
Memory BIOS selectable 16/32/64/128MB shard with system memory
Display Type CRT, LCD monitor with analog display
Connector External DB15 female connector on rear I/O panel
LCD Interface
Chipset VIA CX700M transmitter
Interface 18/24-bit LVDS interface
12V backlight inverter connector
8
Product Specification
Page 9
LE-365 User’s Manual Introduction
Panel voltage 3.3V/5V jumper selectable
Ethernet Interface
Chipset Realtek RTL8110S-32 Gigabit Ethernet controller
Type 10/100/1000 Base-TX
auto-switching Fast Ethernet
Full duplex, IEEE802.3U compliant
Connector External RJ45 connectors with LED on rear I/O panel
Audio Interface
Chipset VIA VT1708A
Interface 2 channel HD audio with Line-out and MIC-in
Connector External Audio phone jack for Line-out
Onboard audio connector with pin header
Onboard CD-IN connector
Expansive Interface
Mini-PCI 2 x 32-bit 5V/3.3V Mini-PCI socket
Solid State Disk
DOM IDE1 supports 44-pin DOM (DiskOnModule)
CompactFlash 1 x CompactFlash Type 2 socket
Power and Environment
Power
Requirement
Dimension 146 (L) x 101 (H) mm
Temperature Operating within 0 ~ 60P
DC 8V~24V input
1 x 2-pin DC_IN connector onboard
o
P
C (32 ~ 140P
o
Storage within -20 ~ 85
P
P
C (-4 ~ 185P
o
P
F)
o
P
F)
Ordering Code
LE-365D Onboard VGA, 1x Gigabit LAN, 4 x USB2.0, 1 x CF, 2 x MinPCI,
HD Audio, 1 x Irda, DVI and HDTV(optional)
LE-365X Onboard VGA,1x Gigabit LAN, 4 x USB2.0, 1 x CF , 2 x MinPCI,
HD Audio ,1 x Irda, LVDS and HDTV(optional)
Product Specification
9
Page 10
LE-365 User’s Manual Introduction
1.3 <Mechanical Drawing>
Mechanical Drawing
10
Page 11
LE-365 User’s Manual Introduction
<IO Mechanical Drawing>
Block Diagram
11
Page 12
LE-365 User’s Manual Introduction
A
1.4 <Block Diagram>
Eden nanoBGA2
1 x 200-pin SO-DIMM
CRT/LCD Monitor
DDR2 400/533MHz
up to 1GB
LVDS or DVI
BIOS
2 x Serial ports
8-bit GPIO
PS/2 KB/MS
IrDA
VT 1708A
4 x USB2.0 ports
83697HG
LPC
CX700M
2 x SAT
CompactFlash＆IDE
ICH7-M
RTL8110S-32
2 x MINI PCI
Mechanical Drawing
12
Page 13
LE-365 User’s Manual Hardware Setup
Chapter 2 <Hardware Setup>
2.1 <Connector Location>
（1）LE-365X
CF
SYSFAN
CPUFAN
CN_LVDS
IDE
CN_INV
MINIPCI2
JFRNT
DC_IN
DC_OUT
CN_USB2
CN_DIO
（2）LE-365D
CN_USB2
CN_DIO
CF
SATA1/2
SYSFAN
SATA1/2
CN AUDIO
CD_IN
CPUFAN
CN AUDIO
CD_IN
CN_IR
MINIPCI2
CN_IR
CN_DVI
IDE
CN_COM2
JFRNT
CN_COM2
DC_IN
DC_OUT
Connector Location
13
Page 14
LE-365 User’s Manual Hardware Setup
DDRII
MINIPCI1
RJ45 PS2 USB CRT COM1
14
Connector Location
Page 15
LE-365 User’s Manual Hardware Setup
2.2 <Jumper Reference>
Jumper Function
JRTC CMOS Operating/Clear Setting
JVLCD LCD Panel Voltage Setting
JAT AT Mode
JCSEL1/2 COM2 RS232/422/485 mode setting
JVLCD
JAT
Jumper Reference
JRTC
JCSEL1
JCSEL2
15
Page 16
LE-365 User’s Manual Hardware Setup
2.3 <Connector Reference>
2.3.1 <Internal Connector>
Connector Function Remark
DDRII 200 -pin DDR2 SO-DIMM SDRAM slot
SATA1/2 7-pin Serial ATA connector
CN_AUDIO 5 x 2-pin audio connector
CD_IN 4-pin CD-ROM audio input connector
CN_DIO 6 x 2-pin digital I/O connector
CN_USB2 5 x 2-pin USB connector
CPUFAN 3-pin CPU cooler fan connector
SYSFAN 3-pin system cooler fan connector
CN_COM2 5 x 2-pin com connector
CN_IR 5-pin IrDA connector
CF Compact Flash Type II socket
CN_LVDS 20 x 2-pin LVDS connector LE-365X
CN_INV 5-pin LCD inverter connector LE-365X
DC_OUT 4-pin power output connector
DC_IN 3-pin power input connector
MINIPCI1/2 Mini-PCI socket
CN_DVI 13 x 2-pin DVI interface LE-365D
JFRNT 14-pin switch/indicator connector
2.3.2 <External Connector>
Connector Function Remark
CRT DB15 VGA connector
USB Dual USB 2.0 connector
COM1 DB9 Serial port connector
RJ45 One RJ45 LAN connector
PS2 PS/2 keyboard and mouse connector
16
Connector Reference
Page 17
LE-365 User’s Manual Hardware
Setup
2.4 <CPU and Memory Setup>
2.4.1< CPU>
The board comes with the VIA V4 Eden 1GHz processor , it supports new generation of
VIA V4 Eden 1GHz processor with 400MHz of front side bus and 2MB L2 cache. Please
follow the instruction to install the CPU properly.
2.4.2 <Memory>
The board provides one 200-pin DDR2 SO-DIMM to supp ort DDR2 400/533 memory
modules up to 1GB of capacity. Non-ECC, unbuffered memory is supported only. While
applying two same modules, dual channel technology is enabled automatically for
higher performance.
CPU＆Memory Setup
DDRII
17
Page 18
LE-365 User’s Manual Hardware Setup
3
2.5 <CMOS ATX Setup>
The board’s data of CMOS can be setting in BIOS. If the board refuses to boot due to
inappropriate CMOS settings, here is how to proceed to clear (reset) the CMOS to its
default values.
Jumper: JRTC
Type: Onboard 3-pin jumper
JRTC Mode
1-2 Clear CMOS
2-3 Normal Operation
Default setting 2-3
Jumper: JAT
Type: onboard 3-pin header
JAT Mode
1-2 AT Mode
2-3 ATX Mode
Default setting 2-3
JAT
1
3 1
JRTC
18
CMOS ATX Setup
Page 19
LE-365 User’s Manual Hardware Setup
2.6 <Enhanced IDE & CF interface>
The board supports one UltraDMA133 IDE interface, and one CompactFlash Type II socket
with secondary IDE mode, the 44-pin IDE connector can support up to 2 ATAPI devices
through IDE cable, and the CompactFlash socket can support IDE DMA mode (depends on
the CF card specification).
43
44
IDE
CF
1
2
CF Interface
19
Page 20
LE-365 User’s Manual Hardware Setup
2.7 <Serial ATA Interface>
Based on VIA CX700M, the board provides two Serial ATA interfaces with up to 300MB/s of
transfer rate
.
SATA1/2
2.8 <LAN Interface>
The Realtek RTL8110S-32 supports triple speed of 10/100/1000Base-T, with IEEE802.3
compliance and Wake-On-LAN supported.
LAN
20
Serial ATA Interface
Page 21
LE-365 User’s Manual Hardware Setup
2.9 <Onboard Display Interface>
Based on VIA CX700M chipset with built-in GMA (Graphic Media Accelerator) 950 graphics,
the board provides one DB15 connector on real external I/O port, and one 40-pin LVDS
interface with 5-pin LCD backlight inverter connector. The board provides dual display
function with clone mode and extended desktop mode for CRT and LCD or DVI .
2.9.1 <Analog VGA Interface>
Please connect your CRT or LCD monitor with DB15 male connector to the onboard DB15
female connector on rear I/O port.
CRT
Onboard Display Interface
21
Page 22
LE-365 User’s Manual Hardware Setup
2
5
2.9.2 <Digital Display>
The board provides one 40-pin LVDS connector for 18/24-bit dual channel panels, supports
up to 1600 x 1200 (UXGA) of resolution, with one LCD backlight inverter connector and one
jumper for panel voltage setting.（LE-365X Only）
40
39
CN_LVDS
1
22
CN_INV
JVLCD
1
Digital Display
Page 23
LE-365 User’s Manual Hardware Setup
Connector: CN_INV Connector: JVLCD
Type: 5-pin LVDS Power Header Type: 3-pin Power select Header
Connector model: JST B5B-XH-A
Pin Description Pin Description
1 +12V 1 VCC(5V)
2 GND 2 LCDVCC
3 GND 3 VCC(3.3V)
4 GND
5 ENABKL
Connector: CN_LVDS
Type: onboard 40-pin connector for LVDS connector
Connector model: HIROSE DF13-40DP-1.25V
Pin Signal Pin Signal
2 LCDVCC 1 LCDVCC
4 GND 3 GND
6 ATX0- 5 BTX0-
8 ATX0+ 7 BTX0+
10 GND 9 GND
12 ATX1- 11 BTX114 ATX1+ 13 BTX1+
16 GND 15 GND
18 ATX2- 17 BTX220 ATX2+ 19 BTX2+
22 GND 21 GND
24 ACLK- 23 BTX326 ACLK+ 25 BTX3+
28 GND 27 GND
30 ATX3- 29 BCLK32 ATX3+ 31 BCLK+
34 GND 33 GND
36 N/C 35 N/C
38 N/C 37 N/C
40 N/C 39 N/C
Digital Display
23
Page 24
LE-365 User’s Manual Hardware Setup
To setup the LCD, you need the component below:
1. A panel with LVDS interfaces.
2. An inverter for panel’s backlight power.
3. A LCD cable and an inverter cable.
For the cables, please follow the pin assignm ent of the connector to make a cable, because
every panel has its own pin assignment, so we do not provide a standard cable; please find a
local cable manufacture to make cables.
LCD Installation Guide:
1. Preparing the LE-365X, LCD panel and the backlight inverter.
2. Please check the datasheet of the panel to see the voltage of the panel, and set the
jumper JVLCD to +5V or +3.3V.
3. You would need a LVDS type cable.
Panel side
For sample illustrator only
4. To connect all of the devices well.
24
Board side
Digital Display
Page 25
LE-365 User’s Manual Hardware Setup
After setup the devices well, you need to select the LCD panel type in the BIOS.
The panel type mapping is list below:
LE-365 BIOS panel type selection form
NO. Resolution Color Channel
0 640 x 480 18 1
1 800 x 600 18 1
2 1024 x 768 18 1
3 1280 x 768 18 1
4 1280 x 1024 18 2
5 1400 x 1050 18 2
6 1600 x 1200 18 2
7 1280 x 800 18 1
8 800 x 480 18 1
9 1024 x 768 18 2
A 1024 x 768 24 1
B 1024 x 768 24 2
C 1280 x 768 24 1
D 1280 x 1024 24 2
E 1400 x 1050 24 2
F 1600 x 1200 24 2
DVI Interface
25
Page 26
LE-365 User’s Manual Hardware Setup
2.9.3 <DVI Interface >
The board also comes with a DVI interface with VIA CX700M for digital video interface.
Connector: CN_DVI（LE-365D Only）
Connector type: 26-pin header connector (pitch = 2.00mm)
Pin Number Assignment Pin Number Assignment
1 TX1+ 2 TX13 Ground 4 Ground
5 TXC+ 6 TXC7 Ground 8 PVDD
9 N/C 10 N/C
11 TX2+ 12 TX213 Ground 14 Ground
15 TX0+ 16 TX017 N/C 18 HPDET
19 DDC_DATA 20 DDCCLK
21 GND 22 N/C
23 N/C 24 N/C
25 N/C 26 N/C
26
26
CN_DVI
Digital Display
Page 27
LE-365 User’s Manual Hardware Setup
2.10 <Onboard Audio Interface>
T The board provides the onboard HD audio interface with VIA VT1708A
Connector: CN_AUDIO
Type: 10-pin (2 x 5) header (pitch = 2.54mm)
Pin Description Pin Description
1 MIC_L 2 Ground
3 MIC_R 4 ACZ_DET
5 Speaker_R 6 MIC Detect
7 SENSE 8 N/C
9 Speaker_L 10 Speaker Detect
Connector: CD_IN
Type: 4-pin header (pitch = 2.54mm)
Pin Description
1 CD – Left
2 Ground
3 Ground
4 CD – Right
9 1
10 2
CN_AUDIO
Onboard Audio Interface
CD_IN
4
1
27
Page 28
LE-365 User’s Manual Hardware Setup
2.11 <USB2.0 Interface>
Based on VIA CX700M , the board provides 4 USB2.0 ports. The USB2.0 interface provides
up to 480Mbps of transferring rate.
Interface USB2.0
Controller CX700M
Transfer Rate Up to 480Mb/s
Output Current 500mA
28
10
CN_USB
5
1
1
CN_IR
USB
USB2.0 Interface
Page 29
LE-365 User’s Manual Hardware Setup
Connector: CN_IR
Type: 5-pin header for SIR Port
Pin Description
1 Vcc
2 N/C
3 IRRX
4 Ground
5 IRTX
Connector: CN_USB
Type: 10-pin (5 x 2) header for USB Port
Pin Description Pin Description
1 VCC 2 VCC
3 Data0- 4 Data15 Data0+ 6 Data1+
7 Ground 8 Ground
9 Ground 10 N/C
PS: The USB2.0 will be only active when you connecting with the USB2.0 devices, if you
insert an USB1.1 device, the port will be changed to USB1.1 protocol automatically. The
transferring rate of USB2.0 as 480Mbps is depending on device capacity, exact transferring
rate may not be up to 480Mbps.
USB2.0 Interface
29
Page 30
LE-365 User’s Manual Hardware Setup
2.12 <GPIO Interface>
The board provides a programmable 8-bit digital I/O interface; you can use this general
purpose I/O port for system control like POS or KIOSK.
Connector: CN_DIO
Type: onboard 2 x 6-pin header, pitch=2.0mm
Pin Description Pin Description
1 Ground 2 Ground
3 GP0 4 GP4
5 GP1 6 GP5
7 GP2 8 GP6
9 GP3 10 GP7
11 VCC 12 +12V
30
CN_DIO
12
1
GPIO Interface
Page 31
LE-365 User’s Manual Hardware Setup
2.13 <Serial Port Jumper Setting >
The board provides two RS232 serial ports, with jumper selectable RS422/485 for COM2.
Connector: CN_COM2
Type: 10-pin (5 x 2) 1.27mm x 2.54mm-pitch header for COM2
Pin Description Pin Description
1 DCD/422TX-/485- 2 RXD/422TX+/485+
3 TXD/422RX+ 4 DTR/422RX5 GND 6 DSR
7 RTS 8 CTS
9 RI 10 N/C
10
JCSEL1 JCSEL2
1
RS-232
5
11
1
RS-485
RS-422
Serial Port Jumper Setting
6
2
12
2
31
Page 32
LE-365 User’s Manual Hardware Setup
32
JCSEL2
JCSEL1
Serial Port Jumper Setting
CN_COM2
1
10
COM1
Page 33
LE-365 User’s Manual Hardware Setup
3
3
3
2.14 <Power and Fan Connector>
The board requires DC input with 3-pin header, the input voltage range is from 8V to 24V,
for the input current, please take a reference of the power consumption report on appendix.
2.15.1 <Power Input>
Connector: DC_IN
Pin Description Pin Description Pin Description
1 DC_IN 2 NC 3 Ground
Remark: D
C input voltage range 8~24V
1
SYSFAN
1
CPUFAN
1
DC_IN
DC_OUT
1
Power and Fan Connector
33
Page 34
LE-365User’s Manual Hardware Setup
2.14.2 <Power Output>
Connector: DC_OUT
Type: 4-pin connector for +5V/+12V output
Pin Description Pin Description Pin Description Pin Description
1 +12V 2 Ground 3 Ground 4 +5V
2.14.3 <Fan Connector>
Connector: SYSFAN, CPUFAN
Type: 3-pin fan wafer connector
Pin Description Pin Description Pin Description
1 Ground 2 +12V 3 Fan Speed detect
34
Indicator and Switch
Page 35
LE-365 User’s Manual Hardware Setup
2.15 <Indicator and Switch>
The JFRNT provides front control panel of the board, such as power button, reset and
beeper, etc. Please check well before you connecting the cables on the chassis.
Connector: JFRNT
Type: onboard 14-pin (2 x 7) 2.54-pitch header
Function Signal PIN Signal Function
IDE LED
Reset
Power
Button
HDLED+ 1 2 PWRLED+
HDLED- 3 4 N/C
Reset+ 5 6 PWRLED-
Reset- 7 8 SPK+
N/C 9 10 N/C
PWRBT+ 11 12 N/C
PWRBT- 13 14 SPK-
Power
LED
Speaker
1
14
JFRNT
Power and Fan Connector
35
Page 36
LE-365User’s Manual Hardware Setup
(This Page is Left For Blank)
36
Indicator and Switch
Page 37
LE-365 User’s Manual
Chapter 3 <System Setup>
3.1 <Display Configuration>
The board provides onboard VGA with DB15 analog display interface, and LVDS LCD
interface for digital display, when connecting two display devices, you can enable dual
display function with clone mode or extended desktop mode.
Before setup the video setting, please install the VGA driver well.
Two controllers for each display device
There are two options for secondary display device
For more display properties setting, please click “Advanced” button.
Display Configuration
37
Page 38
LE-365 User’s Manual System Configuration
Please select S3Display for advanced device setting.
Specified display setup if available
When you set dual display clone mode, you’ll see the same screen display on two devices.
When you set the dual display for extended desktop mode, you can have the independent
desktop on the second device.
38
Audio Configuration
Page 39
LE-365 User’s Manual System Setup
(This Page is Left for Blank)
Display Configuration
39
Page 40
LE-365 User’s Manual BIOS Setup
Chapter 4 <BIOS Setup>
The motherboard uses the Award BIOS for the system configuration. The Award
BIOS in the single board computer is a customized version of the industrial standard
BIOS for IBM PC AT-compatible computers. It supports Intel x86 and compatible CPU
architecture based processors and computers. The BIOS provides critical low-level
support for the system central processing, memory and I/O sub-systems.
The BIOS setup program of the single board computer let the customers modify the
basic configuration setting. The settings are stored in a dedicated battery-backed
memory, NVRAM, retains the information when the power is turned off. If the battery
runs out of the power, then the settings of BIOS will come back to the default setting.
The BIOS section of the manual is subject to change without notice and is provided here
for reference purpose only. The settings and configurations of the BIOS are current at
the time of print, and therefore they may not be exactly the same as that displayed on
your screen.
To activate CMOS Setup program, press ＜DEL＞ key i mmediately after you turn on
the system. The following message “Press DEL to enter SETUP” should appear in the
lower left hand corner of your screen. When you enter the CMOS Setup Utility, the Main
Menu will be displayed as Figure 4-1. You can use arrow keys to select your function,
press ＜Enter＞ key to accept the selection and enter the sub-menu.
Figure 4-1 CMOS Setup Utility Main Screen
BIOS Setup 40
Page 41
LE-365 User’s Manual
(This Page is Left for Blank)
41
Page 42
LE-365 User’s Manual I/O Port Pin Assignment
Appendix A <I/O Port Pin Assignment>
A.1 <IrDA Port>
Connector: CN_IR
Type: 5-pin header for SIR Port
Pin Description
1 Vcc
2 N/C
3 IRRX
4 Ground
5 IRTX
A.2 < CRT Port >
Connector: CRT
Type: 15-pin D-sub female connector on panel
Pin Description Pin Description Pin Description
1 RED 6 Ground 11 N/C
2 GREEN 7 Ground 12 5VCDA
3 BLUE 8 Ground 13 HSYNC
4 N/C 9 LVGA5V 14 VSYNC
5 Ground 10 Ground 15 5VCLK
5
1
6
10
11
12
13
14
15
1
2
3
4
5
A.3 <Serial ATA Port>
Connector: SATA1/2
Type: 7-pin wafer connector
1 2 3 4 5 6 7
GND RSATA_TXP1 RSATA_TXN1 GND RSATA_RXN1 RSATA_RXP1 GND
42
1 7
LAN Port
Page 43
LE-365 User’s Manual I/O Port Pin Assignment
A.4 <Serial Port>
Connector: COM1
Type: 9-pin D-sub male connector on rear panel
5
4
3
2
1
9
8
7
6
Pin Description Pin Description
1 DCD 6 DSR
2 SIN 7 RTS
3 SO 8 CTS
4 DTR 9 RI
5 Ground
A.5 <LAN Port>
Connector: RJ45
Type: RJ45 connector with LED on rear panel
Pin 1 2 3 4 5 6 7 8
Description TX+ TX- RX+ N/C N/C RX- N/C N/C
1
8
IrDA Port
43
Page 44
LE-365 User’s Manual Flash BIOS
Appendix B <Flash BIOS>
B.1 BIOS Auto Flash Tool
The board is based on Award BIOS and can be updated easily by the BIOS auto flash
tool. You can download the tool online at the address below:
TUhttp://www.award.comUT
TUhttp://www.commell.com.tw/support/support.htmUT
File name of the tool is “awdflash.exe”, it’s the utility that can write the data into the
BIOS flash ship and update the BIOS.
B.2 Flash Method
1. Please make a bootable floppy disk.
2. Get the last .bin files you want to update and copy it into the disk.
3. Copy awardflash.exe to the disk.
4. Power on the system and flash the BIOS. (Example: C:/ awardflash XXX.bin)
5. Re-star the system.
Any question about the BIOS re-flash please contact your distributors or visit the
web-site at below:
http://www.commell.com.tw/support/support.htm
44
BIOS Auto Flash Tool
Page 45
LE-365 User’s Manual System Resources
Appendix C <System Resources>
C1.<I/O Port Address Map>
I/O Port Address Map
45
Page 46
LE-365 User’s Manual System Resources
46
I/O Port Address Map
Page 47
LE-365 User’s Manual System Resources
C2.<Memory Address Map>
Memory Address Map
47
Page 48
LE-365 User’s Manual System Resources
C3.<System IRQ Resources>
48
System IRQ Resources
Page 49
LE-365 User’s Manual
Appendix D <Programming GPIO’s>
The GPIO’can be programmed with the MSDOS debug program using simple
IN/OUT commands.The following lines show an example how to do this.
GPIO0…..GPIO7 bit0……bit7
-o 4E 87 ;enter configuration
-o 4E 87
-o 4E 07
-o 4F 07 ;enale GPIO function
-o 4E 29
-o 4F A2 ;enable GPIO configuration
-o 4E F0
-o 4F xx ;set GPIO as input/output; set ‘1’ for input,’0’for
output
-o 4E F1
-o 4F xx ;if set GPIO’s as output,in this register its value can
be set
Optional :
-o 4E F2
-o 4F xx ; Data inversion register ; ‘1’ inverts the current valus
of the bits ,’0’ leaves them as they are
-o 4E 30
-o 4F 01 ; active GPIO’s
For further information ,please refer to Winbond W83697HG datasheet.
49
Page 50
LE-365 User’s Manual Contact Information
Contact Information
Any advice or comment about our products and service, or anything
we can help you please don’t hesitate to contact with us. We will do
our best to support you for your products, projects and business.
Taiwan Commate Computer Inc.
Address
TEL +886-2-26963909
FAX +886-2-26963911
Website
E-Mail
8F, No. 94, Sec. 1, Shin Tai Wu Rd., Shi Chih
Taipei Hsien, Taiwan
TUhttp://www.commell.com.twUT
TUinfo@commell.com.twUT (General Information)
TUtech@commell.com.twUT (Technical Support)
Commell is our trademark of industrial PC division
50
Contact Information
Loading...