HS-874P
Half-size PISA CPU Card
User’ s Manual
Edition: 1.1
2009/05/08
HS-874P User’s Manual
Copyright
Copyright 2008. All rights reserved. This document is copyrighted and all rights are
reserved. The information in this document is subject to change without prior notice to make
improvements to the products.
This document contains proprietary information and protect ed by copyright. No part of this
document may be reproduced, copied, or translated in any form or any means without prior
written permission of the manufacturer.
All trademarks and/or registered trademarks contains in this document are propert y of their
respective owners.
Disclaimer
The company shall not be liable for any incidental or consequenti al dam ages res ultin g from
the performance or use of this product.
The company does not issue a warranty of any kind, e xpress or implied, including without
limitation implied warranties of merchantability or fitness for a particular purpose.
The company has the right to revise the manual or include changes in th e specifications of
the product described within it at any time without notice and without obligation to notify any
person of such revision or changes.
Trademark
All trademarks are the property of their respective holders.
Any questions please visit our website at TUhttp://www.commell.com.twUT.
2
HS-874P User’s Manual
Packing List:
Please check the package material before you install the system.
Hardware:
HS-874P Single Board Computer x 1
Cable Kit:
PS/2 Keyboard & Mouse Cable
4-pin to 3-pin ATX Cable x 1
USB Cable x 2
Audio Port Cable x 1
DVI module with bracket x 1
RAID driver Disk for Windows XP
and Windows Server 2003
SATA Cable x 2
SATA Power Cable x 1
COM Port x 1
Printed Matters:
Driver CD x 1 (Including User’s Manual)
3
HS-874P User’s Manual
Index
Chapter 1 <Introduction>........................................................6
1.1 <Product Overview> ..............................................................................6
1.2 <Product Specification>........................................................................7
1.3 < Drawing >............................................................................................. 9
1.3.1 < Mechanical Drawing >.......................................................................................9
1.3.2 < Motherboard Dimension >...............................................................................10
1.4 <Block Diagram>.................................................................................. 11
Chapter 2 <Hardware Setup>..............................................13
2.1 <Connector Location>.........................................................................13
2.2 <Connector Reference>.......................................................................15
2.2.1 <Internal Connector>..........................................................................................15
2.2.2 <External Connector>.........................................................................................15
2.3 <Jumper Reference>............................................................................16
2.4 <CPU and Memory Setup >.................................................................18
2.4.1 <CPU installation> ......................................................................................... 18
2.4.2 <Memory Setup>............................................................................................19
2.5 <CMOS Setup> .....................................................................................20
2.6 <Serial ATA interface>..........................................................................21
2.7 <LAN Interface>.................................................................................... 21
2.8 <Onboard Display Interface>..............................................................22
2.8.1 <Analog VGA Interface>....................................................................................22
2.8.2 <LVDS Display> (HS-874PX only)....................................................................22
2.8.3 <DVI Display> (HS-874PD only) ......................................................................26
2.9 <Onboard Audio Interface>.................................................................27
2.10 <USB2.0 Interface> ............................................................................28
2.11 <Serial Port Jumper Setting >........................................................... 30
2.12 <Power and Fan Installation> ...........................................................32
2.12.1 <Power connectors>.....................................................................................32
4
HS-874P User’s Manual
2.12.2 <Fan Connectors>........................................................................................33
2.13 <GPIO Interface>................................................................................34
2.14 <Switch and Indicator>......................................................................35
Chapter 3 <System Configuration>...................................37
3.1 <SATA configuration>..........................................................................37
3.2 <SATA RAID Configuration> ...............................................................38
3.3 <Audio Configuration> ........................................................................42
3.4 <Video Memory Setup>........................................................................43
Chapter 4 <BIOS Setup>.......................................................45
Appendix A <I/O Port Pin Assignment>...........................47
A.1 <Serial ATA Port>.................................................................................47
A.2 <Serial Port>.........................................................................................47
A.3 <VGA Port> ......................................................................................47
A.4 <LAN Port>........................................................................................... 48
A.5 <AT Keyboard Port>............................................................................48
A.6 <PS/2 Keyboard & Mouse Port>......................................................... 48
Appendix B <Flash BIOS>....................................................50
B.1 <BIOS Auto Flash Tool>......................................................................50
B.2 <Flash Method> ...................................................................................50
Appendix C <System Resources>.....................................51
C.1 <I/O Port Address Map>......................................................................51
C.2 <Memory Address Map>.....................................................................53
C.3 <System IRQ Resources>...................................................................54
Appendix D <Programming GPIO’s>................................55
Appendix E <Watch Dog timer Setting >.........................56
5
HS-874P User’s Manual Introduction
Chapter 1 <Introduction>
1.1 <Product Overview>
The HS-874P is an all-in-one single board computer with PISA bus supporting Intel Core2
Quad/ Core 2 Duo processor for 800/1066/1333 MHz front side bus, Intel Q35 and ICH9DO
chipset, integrated GMA3100 graphics, DDR2 SO-DIMM memory, Realtek ALC888 HD
Audio, Serial ATA and one Intel 82573L Gigabit LAN.
Intel LGA775 Processor
The board supports Intel Core 2 Quad/ Core 2 Duo processor with 800/1066/1333 MHz
front side bus, 8MB L2 cache, to provide more powerful performance than before.
New features for Intel Q35 chipset
The board integrates Intel Q35 and ICH9DO chipset, to provide new supports Intel
GMA3100 graphics, DDR2 667/800 memory, built-in high speed mass storage interface of
serial ATA, HD Audio with 2 channels surrounding sound.
All in One multimedia solution
Based on Intel Q35 and ICH9DO chipset, the board provides high p erformance onboard
graphics, 24-bit Dual channe l LVDS interface or DVI and 2 channels HD Audio to meet the
every requirement of the multimedia application.
Product Overview
6
HS-874P User’s Manual Introduction
1.2 <Product Specification>
General Specification
Form Factor Half size PISA bus CPU card
CPU Support Intel® Core 2 Quad/ Core 2 Duo processor
Package type: LGA775
Front side bus: 800/1066/1333MHz
Memory DDRII 667/800 MHz SO-DIMM up to 2GB
Chipset Intel® Q35 and ICH9DO
BIOS Phoenix-Award v6.00PG 8Mb SPI flash BIOS
Green Function Power saving mode includes doze, standby and suspend modes.
ACPI version 1.0 and APM version 1.2 compliant
Watchdog Timer System reset programmable watchdog timer with 1 ~ 255 sec./min.
of timeout value
Real Time Clock Chipset integrated RTC with onboard lithium battery
Serial ATA Intel® ICH9DO built-in 4 x Serial ATAII interface up to 300MB/s
Support RAID 0, 1, 5, 10 and Intel Matrix Storage Technology.
Multi-I/O Port
Chipset Intel® ICH9DO with Winbond® W83627DHG controller
Serial Port One RS232 and one jumper selectable RS232/422/485/IR
USB Port 4 x Hi-Speed USB 2.0 ports with 480Mbps of transfer rate
IrDA Port One IrDA compliant Infrared interface supports SIR
K/B & Mouse PS/2 keyboard and mouse port on bracket
GPIO One 12-pin Digital I/O connector with 8-bit programmable
Smart Fan One CPU fan connector for fan speed controllable
VGA Display Interface
Chipset Intel® Q35 & ICH9DO
Memory Up to 384MB shared with system memory
Display Type CRT, LCD monitor with analog display, DVI or LVDS
Connector External DB15 female connector on bracket
Onboard 40-Pin LVDS connector (HS-874PX Only)
Onboard 26-Pin DVI connector (HS-874PD Only)
Ethernet Interface
Chipset Intel 82573L Gigabit Ethernet controller
Type Triple speed 10/100/1000Base-T
auto-switching Fast Ethernet
Full duplex, IEEE802.3U compliant
Connector External one RJ45 connector with LED on bracket
ISA Interface
ISA Bridge Winbond W83628AG & W83629AG
Function I/O & IRQ supported only, no support DMA & bus mastering
Product Specification 7
HS-874P User’s Manual Introduction
ISA Interface
Chipset Intel® ICH9DO with Realtek ALC888 HD Audio
Intel High Definition Audio compliance
Interface 2 channels sound output
Connector Internal 10-pin header for line-in/-out, MIC-in, 4-pin header for
CD-IN
Power and Environment
Power
+5V, +12V power required, optional 5USB for ATX
Requirement
Dimension 185 (L) x 127 (H) mm
Temperature Operating within 0 ~ 60P
Storage within -20 ~ 85
o
P
C (32 ~ 140P
o
P
P
C (-4 ~ 185P
o
o
P
F)
P
F)
Ordering Code
HS-874PD Support Intel Core 2 Quad/Core 2 Duo processor
Onboard VGA, Intel Gigabit LAN, 4 x USB2.0, 2 x serial port
Realtek ALC888 HD Audio, 4 x SATA, 1 x IrDA, DVI Interface
HS-874PX Support Intel Core 2 Quad/ Core 2 Duo processor
Onboard VGA, Intel Gigabit LAN, 4 x USB2.0, 2 x serial port
Realtek ALC888 HD Audio, 4 x SATA, 1 x IrDA, 18/24-bits LVDS
Interface
The specifications may be different as the actual board.
For further product information please visit the website at
TUhttp://www.commell.com.twUT
Product Specification
8
HS-874P User’s Manual Introduction
1.3 < Drawing >
1.3.1 < Mechanical Drawing >
Inch
Mechanical Drawing
9
HS-874P User’s Manual Introduction
1.3.2 < Motherboard Dimension >
127 mm
28.6 mm
185 mm
Block Diagram
10
HS-874P User’s Manual Introduction
r
1.4 <Block Diagram>
Intel GMA3100 Graphics
Intel Core 2 Quad Processo
1 x 200-pin SO-DIMM
DDR2 667/800 MHz
up to 2GB
LVDS
4 x USB2.0 ports
2 x Serial ports
8-bit GPIO
1 x IrDA
CH7308A
CH7307CDVI
W83627DHG
Intel® Q35
ICH9DO
SPI
ISA Bridge
4 x SATA
HD Audio
Intel 82573L
1 x GLAN
PISA Backplane
PCI BUS
Mechanical Drawing
BIOS
11
HS-874P User’s Manual
(This Page is Left for Blank)
12
HS-874P User’s Manual Hardware Setup
Chapter 2 <Hardware Setup>
2.1 <Connector Location>
SYSFAN
CPUFAN
DC_IN
CN_PS
CN_IN
CN_AUDIO
CN_VGA
CN 12V
JFRNT
CN_USB1/2
CN_INV
JVLCD
CN_LVDS
CN_IR
SATA1/2/3/4
CN_ATKB
CN_DVI
Connector Location 13
HS-874P User’s Manual Hardware Setup
SO-DIMM
PS2 COM1 RJ45 CRT
Connector Location
14
HS-874P User’s Manual Hardware Setup
2.2 <Connector Reference>
2.2.1 <Internal Connector>
Connector Function Remark
DIMM 200-pin DDR2 SDRAM SO-DIMM slot Standard
S_ATA1/2/3/4 7-pin Serial ATA connector Standard
DC_IN 4-pin AT power supply connector Standard
CN_12V 4-pin +12V additional power supply connector Standard
CN_PS 3-pin ATX function connector Standard
CN_AUDIO 5 x 2-pin audio connector Standard
CDIN 4-pin CD-ROM audio input connector Standard
CN_DIO 6 x 2-pin digital I/O connector Standard
CN_LVDS 20 x 2-pin LVDS connector (HS-874PX)
CN_INV 5-pin LCD inverter connector (HS-874PX)
CN_USB1/2 5 x 2-pin USB connector Standard
CPUFAN 4-pin CPU cooler fan connector Standard
SYSFAN 3-pin system cooler fan connector Standard
CN_IR 5-pin IrDA connector Standard
CN_ATKB 5-pin AT keyboard connector Standard
CN_DVI 26-pin DVI connector (HS-874PD)
JFRNT 14-pin front panel switch/indicator connector Standard
CN_COM2 10-pin serial port connector Standard
CN_VGA 8 X 2 pin VGA connector (pitch=2.0mm) Standard
2.2.2 <External Connector>
Connector Function Remark
CRT DB15 VGA connector Standard
RJ45 One RJ45 LAN connector Standard
COM1 Serial port connector Standard
PS2 PS/2 keyboard and mouse connector Standard
Connector Reference 15
HS-874P User’s Manual Hardware Setup
2.3 <Jumper Reference>
Jumper Function
JRTC CMOS Operating/Clear Setting
JVLCD LCD Panel Voltage Setting
JCSEL1/2 COM2 RS232/422/485/IR mode setting
JP1/JP2 COM PORT Voltage support
JRTC
JCSEL1
JP2/JP1
JVLCD
JCSEL2
Jumper Reference
16
HS-874P User’s Manual Hardware Setup
Jumper: JP1 (COM 1)
Type: onboard 3 x 2-pin header
JP1 Mode
1-3 Pin1 with +5V power.
2-4 Pin9 with +12V power.
3-5 Pin1 with DCD signal
4-6 Pin9 with RI signal
Default setting
Jumper: JP2 (COM 2)
Type: onboard 3 x 2-pin header
JP2 Mode
1-3 Pin1 with +5V power.
2-4 Pin9 with +12V power.
3-5 Pin1 with DCD/ 422TX-/485- signal
4-6 Pin9 with RI signal
Default setting
JP2 JP1
6 5 6 5
2 1 2 1
CPU installation 17
HS-874P User’s Manual Hardware Setup
f
2.4 <CPU and Memory Setup >
2.4.1 <CPU installation>
HS-874P has a LGA775 CPU socket onboard; please check following steps to install the
processor properly.
Attention If HS-874P needs RMA please Keep CPU socket cover on the CPU Socket.
Warring If CPU Socket internal Pin damage We could not provide warranty.
Intel® Core 2 Duo /Quad processor
Package type: 775 pin PLGA
L2 Cache: 8 MB
FSB: 800/1066/1333MHz (266MHz x 4)
Manufacturing: 65nm, 45nm
Intel Hyper Threading Technology and
1. Lift this bar
Core 2 Duo /Quad supported
Check point
3. Place the CPU on the top o
2. Uncover this plate
4. Lock this bar
Notice: Please place the CPU on the pins tenderlyto avoid bending the pins
the pins
3. Cover this plate
CPU Installation 18
HS-874P User’s Manual Hardware Setup
2.4.2 <Memory Setup>
HS-874P has one 200-pin DDR2 SO-DIMM support up to 2GB of memory capacity. The
memory frequency supports 667/800 MHz. Only Non-ECC memory is supported.
SO-DIMM
Memory Setup 19
HS-874P User’s Manual Hardware Setup
3
2.5 <CMOS Setup>
The board’s data of CMOS can be setting in BIOS. If the board refuses to boot due to
inappropriate CMOS settings, here is how to proceed to clear (reset) the CMOS to its
default values.
Jumper: JRTC
Type: Onboard 3-pin jumper
JRTC Mode
1-2 Clear CMOS
2-3 Normal Operation
Default setting
JRTC
1
CMOS Setup 20
HS-874P User’s Manual Hardware Setup
2.6 <Serial ATA interface>
Based on Intel ICH9DO, the board provides four Serial ATA interfaces with up to 300MB/s of
transfer rate
.
SATA1/2/3/4
2.7 <LAN Interface>
The Intel 82573L supports triple speed of 10/100/1000Base-T, with IEEE802.3 complia nce
and Wake-On-LAN supported.
LAN
Serial A TA Interface 21
HS-874P User’s Manual Hardware Setup
2.8 <Onboard Display Interface>
Based on Intel Q35 chipset with built-in GMA (Graphic Media Accelerator) 3100 graphics,
the board provides one DB15 connector on real external I/O port, and one 40-pin LVDS
interface with 5-pin LCD backlight inverter connector. The board provides dual display
function with clone mode and extended desktop mode for CRT and LCD or DVI.
2.8.1 <Analog VGA Interface>
Please connect your CRT or LCD monitor with DB15 male connector to the onboard DB15
female connector on rear I/O port.
2.8.2 <LVDS Display> (HS-874PX only)
The board provides one 40-pin LVDS connector for 18/24-bit dual channel panels, supports
up to 1600 x 1200 (UXGA) of resolution, with one LCD backlight inverter connector and one
jumper for panel voltage setting.
VGA
2
1
Effective patterns of connection: 1-2 / 3-4 / 5-6
4
3
JVLCD
5
6
1
CN_INV
5
1
CN_LVDS
2 40
39
Warning: others cause damages
22
Digital Display
HS-874P User’s Manual Hardware Setup
Connector: CN_INV Connector: JVLCD
Type: 5-pin LVDS Power Header Type: 6-pin Power select Header
Connector model: JST B5B-XH-A
Pin Description
1 +12V
2 GND
3 GND
4 GND
5 ENABKL
Connector: CN_LVDS
Type: onboard 40-pin connector for LVDS connector
Connector model: HIROSE DF13-40DP-1.25V
Pin Signal Pin Signal
2 LCDVCC 1 LCDVCC
4 GND 3 GND
6 ATX0- 5 BTX0-
8 ATX0+ 7 BTX0+
10 GND 9 GND
12 ATX1- 11 BTX114 ATX1+ 13 BTX1+
16 GND 15 GND
18 ATX2- 17 BTX220 ATX2+ 19 BTX2+
22 GND 21 GND
24 ACLK- 23 BTX326 ACLK+ 25 BTX3+
28 GND 27 GND
30 ATX3- 29 BCLK32 ATX3+ 31 BCLK+
34 GND 33 GND
36 N/C 35 N/C
38 N/C 37 N/C
40 N/C 39 N/C
Pin Description
1-2 LCDVCC (3.3V)
3-4 LCDVCC (5V)
5-6 LCDVCC (+12V)
Default setting
Digital Display
23
HS-874P User’s Manual Hardware Setup
To setup the LCD, you need the component below:
1. A panel with LVDS interfaces.
2. An inverter for panel’s backlight power.
3. A LCD cable and an inverter cable.
For the cables, please follow the pin assignment of the connector to make a cable,
because every panel has its own pin assignment, so we do not provide a standard
cable; please find a local cable manufacture to make cables.
LCD Installation Guide:
1. Preparing the HS-874PX, LCD panel and the backlight inverter.
2. Please check the datasheet of the panel to see the voltage of the panel, and set the
jumper JVLCD to +5V or +3.3V or +12V
3. You would need a LVDS type cable.
Panel side
For sample illustrator only
Board side
4. To connect all of the devices well.
24
Digital Display
HS-874P User’s Manual Hardware Setup
After setup the devices well, you need to select the LCD panel type in the BIOS.
The panel type mapping is list below:
BIOS panel type selection form
Single channel Dual channel
NO. Output format NO. Output format
1 800 x 600 (18bit) 3 1280 x 1024 (24bit)
2 1024 x 768 (24bit) 4 1366 x 768 (24bit)
Digital Display
25
HS-874P User’s Manual Hardware Setup
2.8.3 <DVI Display> (HS-874PD only)
The board provides optional DVI-D interface with Intel Q35, compliant with DVI 1.0
standard.
Connector: CN_DVI
Connector type: 26-pin header connector (pitch = 2.0mm)
Pin Number Assignment Pin Number Assignment
1 TX1+ 2 TX13 Ground 4 Ground
5 TXC+ 6 TXC7 Ground 8 PVDD
9 N/C 10 N/C
11 TX2+ 12 TX213 Ground 14 Ground
15 TX0+ 16 TX017 N/C 18 HPDET
19 DDCDATA 20 DDCCLK
21 GND 22 N/C
23 N/C 24 N/C
25 N/C 26 N/C
26
2
1
CN_DVI
26
25
Digital Display
HS-874P User’s Manual Hardware Setup
2.9 <Onboard Audio Interface>
The board provides the onboard HD 2-channel audio interface with Realtek ALC888
Connector: CN_AUDIO
Type: 10-pin (2 x 5) header (pitch-2.54mm)
Pin Description Pin Description
1 MIC_L 2 Ground
3 MIC_R 4 ACZ_DET
5 Speaker_R 6 MIC Detect
7 SENSE 8 N/C
9 Speaker_L 10 Speaker Detect
Connector: CDIN
Type: 4-pin header (pitch = 2.54mm)
Pin Description
1 CD – Left
2 Ground
3 Ground
4 CD – Right
CN_IN
4
1
10
9
1
2
CN_AUDIO
Onboard Audio Interface 27
HS-874P User’s Manual Hardware Setup
2.10 <USB2.0 Interface>
Based on Intel ICH9DO, the board provides 4 USB2.0 ports. The USB2.0 interface provides
up to 480Mbps of transferring rate.
Interface USB2.0
Controller ICH9DO
Transfer Rate Up to 480Mb/s
Output Current 500mA
1
CN_IR
5
2 10 2 10
CN_USB1/2
USB2.0 Interface 28
HS-874P User’s Manual Hardware Setup
Connector: CN_IR
Type: 5-pin header for SIR Port
Pin Description
1 Vcc
2 N/C
3 IRRX
4 Ground
5 IRTX
Connector: CN_USB1/2
Type: 10-pin (5 x 2) header for USB Port
Pin Description Pin Description
1 VCC 2 VCC
3 Data0- 4 Data15 Data0+ 6 Data1+
7 Ground 8 Ground
9 Ground 10 N/C
PS: The USB2.0 will be only active when you connecting with the USB2.0 devices, if you
insert an USB1.1 device, the port will be changed to USB1.1 protocol automatically. The
transferring rate of USB2.0 as 480Mbps is depending on device capacity exact transferring
rate may not be up to 480Mbps.
USB2.0 Interface 29
HS-874P User’s Manual Hardware Setup
2.11 <Serial Port Jumper Setting >
The board supports one RS232 serial port and one jumper selectable RS232/422/485 serial
ports. The jumper JCSEL1 & JCSEL2 can let you configure the communicating modes for
COM2.
Connector: CN_COM2
Type: 10-pin (5 x 2) 2.54mm x 2.54mm-pitch header for COM2
Pin Description Pin Description
1 DCD/422TX-/485- 2 RXD/422TX+/485+
3 TXD/422RX+ 4 DTR/422RX5 GND 6 DSR
7 RTS 8 CTS
9 RI 10 N/C
JCSEL1 JCSEL2
RS-232
RS-485
RS-422
IR
2
1
2
1
2
1
2
1
Default setting: RS-232
8
7
8
7
8
7
8
7
12
2
12
2
12
2
12
2
11
1
11
1
11
1
11
1
Power and Fan Installation 30
HS-874P User’s Manual Hardware Setup
JCSEL2
12
2
11
2
JCSEL1
1
CN_COM2
1
8
7
Power and Fan Installation 31
HS-874P User’s Manual Hardware Setup
2.12 <Power and Fan Installation>
The board comes with a 4-pin AT and 4pin 12V power connector for powering the board,
two fan connectors for CPU and system. The board also provides a 3-pin ATX function
connector. You can just connect the two power connectors without any backplane to work.
2.12.1 <Power connectors>
Connector: DC_IN
Type: 4-pin P-type connector for +5V/+12V input
Pin Description Pin Description Pin Description Pin Description
1 +12V 2 Ground 3 Ground 4 +5V
Connector: DC_12V
Type: 4-pin P-type connector for +5V/+12V input
Pin Description Pin Description Pin Description Pin Description
1 Ground 2 Ground 3 +12V 4 +12V
Connector: CN_PS
Type: 3-pin ATX function connector
Pin Description Pin Description Pin Description
1 5V Standby 2 Ground 3 Power On
Power and Fan Installation 32
HS-874P User’s Manual Hardware Setup
313
3
2.12.2 <Fan Connectors>
Connector: CPUFAN
Type: 4-pin fan wafer connector
Pin Description Pin Description
1 Ground 2 +12V
3 Fan Speed Detection 4 Fan Control
Connector: SYSFAN
Type: 3-pin fan wafer connector
Pin Description Pin Description Pin Description
1 Ground 2 +12V 3 Fan Speed Detection
SYSFAN
1 2
3
CPUFAN
1
4
DC_IN
14
CN_PS
1
Power and Fan Installation
33
HS-874P User’s Manual Hardware Setup
2.13 <GPIO Interface>
The board provides a 12-pin General Purpose I/O interface, with programmable 8-bit I/O
(4-bit input & 4-bit output).
Connector: CN_DIO
Type: onboard 2 x 6-pin header, pitch=2.0mm
Pin Description Pin Description
1 Ground 2 Ground
3 GP10 4 GP14
5 GP11 6 GP15
7 GP12 8 GP16
9 GP13 10 GP17
11 VCC 12 +12V
11
12
1
2
CN_DIO
Power and Fan Installation
34
HS-874P User’s Manual Hardware Setup
2.14 <Switch and Indicator>
The JFRNT provides front control panel of the board, such as power button, reset and
beeper, etc. Please check well before you connecting the cables on the chassis.
Connector: JFRNT
Type: onboard 14-pin (2 x 7) 2.54-pitch header
Function Signal PIN Signal Function
IDE LED
Reset
Power
Button
HD LED+ 1 2 PWDLED+
Power
HD LED- 3 4 N/C
LED
Reset+ 5 6 PWDLED-
Reset- 7 8 SPKIN+
N/C 9 10 N/C
Speaker
PWRBT+ 11 12 N/C
PWRBT- 13 14 SPKIN-
2
1
JFRNT
14
13
35
HS-874P User’s Manual
(This Page is Left for Blank)
36
HS-874P User’s Manual
Chapter 3 <System Configuration>
3.1 <SATA configuration>
SATA Mode:
This option can let you select whether the Serial ATA hard drives would work under normal
IDE mode or RAID mode. The RAID mode need more than one HDD is applied.
37
HS-874P User’s Manual
3.2 <SATA RAID Configuration>
The board integrates Intel® ICH9DO with RAID function for Serial ATA II drives, and
supports the configurations below:
RAID 0 (Stripping): Two hard drives operating as one drive for optimized data R/W
performance. It needs two unused drives to build this operation.
RAID 1 (Mirroring): Copies the data from first drive to second drive for data security, and if
one drive fails, the system would access the applications to the workable drive. It needs two
unused drives or one used and one unused driv e to build this operation. The second drive
must be the same or lager size than first one.
RAID 5 (striping with parity)
A RAID 5 array contains three or more hard drives where the data is divided into
manageable blocks called strips. Parity is a mathematical method for recreating data that
was lost from a single drive, which increases fault-tolerance. The data and parity are striped
across all the hard drives in the array. The parity is striped in a rotating sequence to reduce
bottlenecks associated with the parity calculations.
RAID 10 (RAID 0+1)
A RAID 10 array uses four hard drives to create a combination of RAID levels 0 and 1. The
data is striped across a two-drive array forming the RAID 0 component. Each of the drives
in the RAID 0 array is then mirrored by a RAID 1 component.
Intel Matrix Storage Technology: This technology would allow you to use RAID 0+1 mode
on only two drives (4 drives needed on traditional RAID 0+1). It will create two partitions on
each hard drive to simulate RAID 0 and RAID 1. It also can let you modify the partition size
without re-formatted.
For more information of Intel Matrix S4torage Technology, please visit Intel’s website.
If you need to install an operation system on the RAID set, please use the driver disk
attached in the package when it informs you to obtain the RAID drivers.
38
HS-874P User’s Manual
Please press <CTRL+I> to enter the RAID configuration menu.
You can setup the RAID under operation system for Microsoft® Windows XP SP1, please
install the Intel® Application Accelerator Ver.7.8 later to support RAID configuration with
Intel® Matrix Storage Technology.
1. After installing Intel Application Accelerator, please execute Intel® Storage Utility.
Demo configuration for 2 SATA Drives and
set as Intel Matrix Storage Technology set
39
HS-874P User’s Manual
2. Select Actions to Create RAID Volume
Rename the Volume name
Select RAID Level as 0
Left as default
40
HS-874P User’s Manual
3. Please select two hard drives to prepare to set the RAID volume
4. Specify the Volume size
Tune this bar to specify
the volume size, if you
specify the volume size
lower than maximum,
you can create a second
volume for another
RAID set.
(Make RAID 0+1 on only
two hard drives)
5. Repeat the step 1 to create second volume as RAID Level 1.
For other configuration set please click Help on tool bar.
41
HS-874P User’s Manual
3.3 <Audio Configuration>
The board integrates Intel® ICH9DO with REALTEK® ALC888 code. It can support
2-channels sound under system configuration. Please foll ow the steps below to setup your
sound system.
1. Install REALTEK HD Audio driver.
2. Lunch the control panel and Sound Effect Manager.
3. Select Speaker Configuration
4. Select the sound mode to meet your speaker system.
42
HS-874P User’s Manual BIOS Setup
3.4 <Video Memory Setup>
Based on Intel® Q35 chipset with GMA (Graphic Media Accelerator) 3100, the board
supports Intel® DVMT (Dynamic Video Memory Technology) 3.0, which would allow the
video memory be triggered up to 384MB.
To support DVMT, you need to install the Intel GMA 3100 Driver with supported OS.
BIOS Setup:
On-Chip Frame Buffer Size:
This item can let you select video memory which been allocated for legacy VGA and SVGA
graphics support and compatibility. The available option is 1MB and 8MB.
DVMT Mode:
This item can let you select Graphics shared memory DVMT or Fixed.
DVMT/FIXED Memory Size:
This item can let you select size of video memory, the system would configure the video
memory depends on your application, If set DVMT mode this item is strongly recommend to
be selected as MAX.
BIOS Setup 43
HS-874P User’s Manual System Configuration
System
Memory
256MB ~ 511MB
512MB~1023MB
1024MB upper
On-Chip
Frame
Buffer Size
1MB 128MB 0MB 128MB
1MB 0MB 128MB 128MB
8MB 128MB 0MB 128MB
8MB 0 128MB 128MB
1MB 128MB 0 128MB
1MB 256MB 0 256MB
1MB 0 128MB 128MB
1MB 0 256MB 256MB
8MB 128MB 0 128MB
8MB 256MB 0 256MB
8MB 0 128MB 128MB
8MB 0 256MB 256MB
1MB 128MB 0 128MB
1MB 256MB 0 256MB
1MB 0 128MB 128MB
1MB 0 256MB 256MB
1MB 0 MAX 384MB
8MB 128MB 0 128MB
8MB 256MB 0 256MB
8MB 0 128MB 128MB
8MB 0 256MB 256MB
8MB 0 MAX 384MB
Fixed
Memory
Size
DVMT
Memory
Size
Total
Graphic
Memory
Notice:
1. The On-Chip Frame Buffer Size would be included in the Fixed Memory.
2. Please select the memory size according to this table.
Audio Setup 44
HS-874P User’s Manual BIOS Setup
Chapter 4 <BIOS Setup>
The motherboard uses the Award BIOS for the system configuration. The Award BIOS in
the single board computer is a customized version of the in dustrial standard BIOS for IBM
PC AT-compatible computers. It supports Intel x86 and compatible CPU architecture based
processors and computers. The BIOS provides critical low-level support for the system
central processing, memory and I/O sub-systems.
The BIOS setup program of the single board computer let the customers modif y the basic
configuration setting. The settings are stored in a dedicated battery-backed memory,
NVRAM, retains the information when the power is turned off. If the battery runs out of the
power, then the settings of BIOS will come back to the default setting.
The BIOS section of the manual is subject to change without notice and is provided here for
reference purpose only. The settings and configurations of t he BIOS are current at th e time
of print, and therefore they may not be exactly the same as that displayed on your screen.
To activate CMOS Setup program, press ＜DEL＞ key immediately after you t urn on the
system. The following message “Press DEL to enter SETUP” should appear in the lower left
hand corner of your screen. When you enter the CMOS Setup Utility, the Main Menu will be
displayed as Figure 4-1. You can use arrow keys to select your function, press ＜Enter＞
key to accept the selection and enter the sub-menu.
Figure 4-1 CMOS Setup Utility Main Screen
BIOS Setup 45
HS-874P User’s Manual
(This Page is Left for Blank)
46
HS-874P User’s Manual
Appendix A <I/O Port Pin Assignment>
A.1 <Serial ATA Port>
Connector: SATA1/2/3/4
Type: 7-pin wafer connector
1 2 3 4 5 6 7
GND RSATA_TXP1 RSATA_TXN1 GND RSATA_RXN1 RSATA_RXP1 GND
A.2 <Serial Port>
Connector: COM1
Type: 9-pin D-sub male connector on I/O l bracket
Pin Description Pin Description
1 DCD 6 DSR
2 SIN 7 RTS
3 SO 8 CTS
4 DTR 9 RI
5 Ground
5
4
3
2
1
9
8
7
6
A.3 <VGA Port>
Connector: CRT
Type: 15-pin D-sub female connector on bracket
Pin Description Pin Description Pin Description
1 RED 6 Ground 11 N/C
2 GREEN 7 Ground 12 5VCDA
3 BLUE 8 Ground 13 HSYNC
4 N/C 9 LVGA5V 14 VSYNC
5 Ground 10 Ground 15 5VCLK
AT Keyboard Port 47
6
10
11
12
13
14
15
1
2
3
4
5
HS-874P User’s Manual
A.4 <LAN Port>
Connector: RJ45
Type: RJ45 connector with LED on bracket
Pin 1 2 3 4 5 6 7 8
Description TRD0+ TRD0- TRD1+ TRD2+ TRD2- TRD1- TRD3+ TRD3-
1
8
A.5 <AT Keyboard Port>
Connector: CN_ATKB
Type: 5-pin box header
Pin 1 2 3 4 5
Description VCC Ground N/C DATA CLK
1
5
A.6 <PS/2 Keyboard & Mouse Port>
Connector: PS2
Type: 6-pin Mini-DIN connector on bracket
Pin 1 2 3 5 6 8
Description KBD MSD Ground VCC KBC MSC
Note: The PS/2 connector supports standard PS/2 keyboard directly or both PS/2 keyboard and
5
2
8
6
1
3
mouse through the PS/2 Y-type cable.
PS2
AT Keyboard Port 48
HS-874P User’s Manual
(This Page is Left for Blank)
49
HS-874P User’s Manual Flash BIOS
Appendix B <Flash BIOS>
B.1 <BIOS Auto Flash Tool>
The board is based on Award BIOS and can be updated easily by the BIOS auto flash
tool. You can download the tool online at the address below:
TUhttp://www.award.comUT
TUhttp://www.commell.com.tw/support/support.htmUT
File name of the tool is “awdflash.exe”, it’s the utility that can write the data into the
BIOS flash ship and update the BIOS.
B.2 <Flash Method>
1. Please make a bootable floppy disk.
2. Get the last .bin files you want to update and copy it into the disk.
3. Copy awardflash.exe to the disk.
4. Power on the system and flash the BIOS. (Example: C:/ awardflash XXX.bin)
5. Re-star the system.
Any question about the BIOS re-flash please contact your distributors or visit the
web-site at below:
http://www.commell.com.tw/support/support.htm
50
BIOS Auto Flash Tool
HS-874P User’s Manual System Resources
Appendix C <System Resources>
C.1 <I/O Port Address Map>
I/O Port Address Map
51
HS-874P User’s Manual System Resources
52
I/O Port Address Map
HS-874P User’s Manual Programming GPIO’s
C.2 <Memory Address Map>
Programming GPIO’s 53
HS-874P User’s Manual Watch Dog timer Setting
C.3 <System IRQ Resources>
Programming GPIO’s
54
HS-874P User’s Manual Programming GPIO’s
Appendix D <Programming GPIO’s>
The GPIO can be programmed with the MSDOS debug program using simple
IN/OUT commands. The following lines show an example how to do this.
GPIO0...GPIO7 bit0……bit7
-o 2E 87 ;enter configuration
-o 2E 87
-o 2E 2A
-o 2F FD ;enable GPIO function
-o 2E 07
-o 2F 07 ;enable GPIO configuration
-o 2E F0
-o 2F xx ;set GPIO as input/output; set ‘1’ for input,’0’for output
-o 2E F1
-o 2F xx ;if set GPIO’s as output, in this register its value can be set
Optional :
-o 2E F2
-o 2F xx ; Data inversion register ; ‘1’ inverts the current value of the bits ,’0’
leaves them as they are
-o 2E 30
-o 2F 01 ; active GPIO’s
For further information, please refer to Winbond W83627DHG datasheet.
Programming GPIO’s 55
HS-874P User’s Manual Watch Dog timer Setting
Appendix E <Watch Dog timer Setting >
The watchdog timer makes the system auto-reset while it stops to work for a period. The
integrated watchdog timer can be setup as system reset mode by program.
Timeout Value Range
- 1 to 255
- Second or Minute
Program Sample
Watchdog timer setup as system reset with 5 second of timeout
2E, 87
2E, 87
2E, 07
2F, 08 Logical Device 8
2E, 30
2F, 01 Activate
2E, F5
2F, 00 Set as Second*
2E, F6
2F, 05 Set as 5
* Minute: bit 3 = 0; Second: bit 3 = 1
You can select Timer setting in the BIOS, after setting the time options, the system will
reset according to the period of your selection.
Watch Dog timer Setting
56
HS-874P User’s Manual
(This Page is Left for Blank)
57
HS-874P User’s Manual Contact Information
Contact Information
Any advice or comment about our products and service, or anything
we can help you please don’t hesitate to contact with us. We will do
our best to support you for your products, projects and business
Taiwan Commate Computer Inc.
Address
TEL +886-2-26963909
FAX +886-2-26963911
Website http://www.commell.com.tw
E-Mail info@commell.com.tw
Commell is our trademark of industrial PC division
19F, No. 94, Sec. 1, Shin Tai Wu Rd., Shi Chih
Taipei Hsien, Taiwan
(General Information)
tech@commell.com.tw
(Technical Support)
58
Contact Information
Loading...