Page 1
HS-862
User’s Manual
Edition 1.1
Copyright
Copyright© 2002, 2003. All rights reserved. This document is copyrighted and
all rights are reserved. The information in this document is subject to change
without prior notice to make improvements to the products.
This document contains proprietary information and protected by copyright.
No part of this document may be reproduced, copied, or translated in any
form or any means without prior written permission of the manufacturer.
All trademarks and/or registered trademarks contains in this document are
property of their respective owners.
Disclaimer
Taiwan Commate Computer Inc. shall not be liable for any incidental or
consequential damages resulting from the performance or use of this product.
Taiwan Commate Computer Inc. does not issue a warranty of any kind,
express or implied, including without limitation implied warranties of
merchantability or fitness for a particular purpose.
The company has the right to revise the manual or include changes in the
specifications of the product described within it at any time without notice and
without obligation to notify any person of such revision or changes.
Trademark
All trademarks are the property of their respective holders.
Any question please visit our website at http://www.commell.com.tw
.
HS-862 User’s Manual
1
Page 2
Packing List
Hardware
HS-862 CPU Card ...................................................... X 1
Cable Kit
IDE Flat Cable (40-pin) ............................................... X 1
Floppy Cable............................................................... X 1
DB9 COM / DB15 Parallel Port Cable with Bracket .... X 1
Dual USB Cable with Bracket ..................................... X 2
PS/2 Keyboard and Mouse Cable............................... X 1
Audio Cable with Bracket ............................................ X 1
Printed Matter and Software
User’s Manual ............................................................. X 1
Driver CD .................................................................... X 1
2
HS-862 User’s Manual
Page 3
Table of Content
Chapter 1. Introduction ......................................................................5
1.1 Product Overview ........................................................................ 5
1.2 Specification ................................................................................ 6
1.3 Component Placement................................................................ 9
1.4 Block Diagram ...........................................................................10
Chapter 2. Hardware Setup..............................................................11
2.1 Jumper and Connector Location ............................................... 11
2.2 CPU and DRAM Setting ............................................................14
2.3 CMOS Setting ...........................................................................14
2.4 Watchdog Timer Setting ............................................................ 15
2.5 Embedded Solid State Flash Disk .............................................16
2.6 Power and Fan Connector......................................................... 17
2.7 VGA Interface............................................................................ 18
2.8 Ethernet Interface...................................................................... 23
2.9 Audio Interface .......................................................................... 24
2.10 Switches and Indicators ............................................................25
Chapter 3. BIOS Setup......................................................................27
3.1 Advanced Chipset Feature ........................................................ 28
3.2 Frame Buffer Size ..................................................................... 29
3.3 Display Device........................................................................... 29
3.4 LCD Type .................................................................................. 30
Chapter 4. Driver Installation...........................................................31
HS-862 User’s Manual
3
Page 4
Appendix A. I/O Port Pin Assignment.............................................33
A.1 IDE Port .................................................................................... 33
A.2 Floppy Port................................................................................ 34
A.3 Parallel Port .............................................................................. 35
A.4 RS-232 Serial Port .................................................................... 36
A.5 USB Port................................................................................... 37
A.6 IrDA Port ................................................................................... 37
A.7 VGA Port................................................................................... 37
A.8 LAN Port ................................................................................... 38
A.9 AT Keyboard Port...................................................................... 38
A.10 PS/2 Keyboard and Mouse Port................................................ 38
Appendix B. Flash the BIOS...........................................................39
B.1 BIOS Auto Flash Tool................................................................ 39
B.2 Flash Method ............................................................................ 39
Appendix C. System Resource........................................................41
C.1 I/O Port Address Map................................................................ 41
C.2 Memory Address Map............................................................... 42
C.3 IRQ and DMA Resource............................................................ 43
4
HS-862 User’s Manual
Page 5
Chapter 1. Introduction
1.1 Product Overview
The HS-862 SBC (Single Board Computer) is an all-in-one industrial half-size
CPU card based on Intel socket 370 architecture, supports Intel
Tualatin/Coppermine FC-PGA II, FC-PGA Pentium-III / Celeron and VIA C3
CPU up to 1.4 GHz at 66, 100, 133 MHz of FSB with PC100/133 SDRAM.
Based on the value VIA/S3 Twister-T chipset with VIA PN133T northbridge
and 686B southbridge, the FS-961 supports the Intel and VIA latest socket
370 based CPU, 1 GBytes PC133 SDRAM and VIA/S3 Savage4 3D SVGA
core with BIOS selectable 8/16/32 MB video memory shard with system
memory.
To be the requirement of multi-media computing platform, the HS-862 also
offers the 18-bit dual-channel LVDS/TTL TFT/DSTN LCD interface. The
onboard Fast Ethernet, audio and CompactFlash interfaces also offer the
features for the industrial PC, server and workstation, portable workstation,
node terminal, transaction station and industrial embedded application.
With these features, HS-862 should be the value, powerful and all-in-one
integration solution including, but not limited to the following.
Value Advanced Computing Platform
Intel latest Tualatin Pentium-III / Celeron and VIA C3 CPU up to 1.4 GHz with
133 MHz FSB, 1GBytes PC133 SDRAM of system memory for high-end
industrial computing platform with high CPU and memory loading.
LVDS/TTL TFT/DSTN LCD Interface
VIA/S3 Twister-T integrated S3 Savage4 3D SVGA core, BIOS selectable
8/16/32 MB of video memory shared with system memory, and 18-bit
dual-channel LVDS / TTL TFT/DSTN LCD interface offers the value and
performance solution for the LCD-based multi-media applications.
.
Solid State Disk Interface
Onboard CompactFlash socket supports CFC (CompactFlash Card) up to 1
GBytes of flash memory capacity. The onboard IDE port with jumper
selectable power input also supports power cable free IDE-based DOM
(DiskOnModule) and M-systems DiskOnChip IDE Pro SSD (Solid State Disk)
for disk free and embedded OS based application.
HS-862 User’s Manual
5
Page 6
1.2 Specification
General Specification
Form Factor Half-size ISA-bus CPU Card / Slot PC
CPU Socket 370 Intel Pentium-III / Celeron, VIA C3 CPU
Up to 1.4 GHz at 66/100/133 MHz of FSB
Intel Tualatin / Coppermine FC-PGA2 / FC-PGA CPU
and VIA C3 Samuel I/II, Ezra, Nehemiah CPU
Chipset VIA Twister-T chipset with PN133T and 686B
Memory One 144-pin SO-DIMM sockets support up to 1 GBytes
of PC100/133 SDRAM
BIOS Phoenix-Award 2Mb PnP flash BIOS
Enhanced IDE PCI enhanced IDE interface supports dual ports up to 4
ATAPI devices with UltraATA/100 supported
Jumper selectable Vcc power output on IDE2 for power
cable free DOM (DiskOnModule) flash disk
Green Function Power saving mode supported in BIOS with DOZE,
STANDBY and SUSPEND modes. ACPI version 1.0
and APM version 1.2 compliant
Watchdog Timer 6-level generates NMI or system reset programmable
watchdog timer
Real Time Clock VIA 686B built-in RTC with onboard lithium battery
Multi-I/O Port
Chipset VIA 686B chipset built-in super I/O controller
Serial Port Two RS-232 serial ports with 16C550 compatible UART
and 16 bytes FIFO
Parallel Port One bi-direction parallel port with SPP/ECP/EPP mode
USB Port Four USB ports with USB version 1.1 compliant
Floppy Port One floppy port supports up to two FDD
IrDA Port One IrDA compliant Infrared interface supports SIR
AT Keyboard One AT keyboard port
K/B & Mouse PS/2 keyboard and mouse port
6
HS-862 User’s Manual
Page 7
Solid State Disk Interface
Flash Type CompactFlash socket for CFC (CompactFlash Card)
IDE-based DOM (DiskOnModule) and M-systems
DiskOnChip IDE Pro
Capacity 32M to 1GBytes of flash memory for CFC
16M to 512 MBytes of flash memory for DOM
Transfer Rate PIO mode 4 up to 16.6 MBytes/sec.
Mode Selection Jumper selectable Master / Slave mode on primary IDE
port for CFC (CompactFlash Card)
Jumper selectable +5V Vcc power input for power cable
free DOM on secondary IDE port
VGA Interface
Chipset VIA/S3 Twister-T PN133T chipset built-in S3 Savage4
SVGA controller with 128-bit 3D/2D engine
Video Memory BIOS selectable 8/16/32 MBytes of video memory
shared with system memory
Display Type CRT and LCD monitor
LVDS/TTL TFT/DSTN Color LCD
CRT Mode VGA, SVGA, XGA, SXGA, UXGA
Up to 1920 x 1440 of resolution for CRT monitor
LCD Mode 36-bit TFT/DSTN LCD interface with 256 gray shade
Integrated 2-channel 110 MHz LVDS interface
Support up to 1280 x 1024 of resolution
CRT Connector External DB15 female connector on bracket
Internal 16-pin header connector onboard
LCD Connector Onboard 50-pin header connector for TTL LCD
Onboard 2 x 20-pin Hirose DF13-20DP-1.25V for LVDS
Audio Interface
Chipset VIA 686B built-in AC97 3D audio controller with codec
Interface Line-in, line-out, Mic-in and CD-in
Connector Onboard 10-pin header for line-in, line-out and Mic-in
Onboard 4-pin header for CD-in
HS-862 User’s Manual
7
Page 8
Power and Environment
Power Req. +5V, +12V, -12V DC input
+5V @ 4.2A typically with Intel Socket 370 FC-PGA
Pentium-III 866 MHz CPU and 128 MB PC133 SDRAM
ATX Function One 3-pin ATX interface with PS-ON and 5V standby
Dimension 185 x 127 mm (L x H)
Weight 0.37 Kg for board only; 1.18 Kg with standard package
Temperature Operating within 0 ~ 60
Storage within -20 ~ 85
o
C (32 ~ 140oF)
o
C (-4 ~ 185oF)
Ordering Code
HS-862VXL Half-size ISA bus CPU Card with Socket 370 CPU,
VGA, LVDS, Audio, LAN, PC/104 and Compact Flash
interface.
8
HS-862 User’s Manual
Page 9
1.3 Component Placement
FRONT
Socket 370 support
Intel Tualatin
Pentium-III/Celeron
VIA C3 CPU
With 100/133 FSB
VIA Twister-T with PN133T
and VT82C686B chipset
144-pin SO-DIMM
SDRAM Socket
Realtek
ALC201A
PC/104
interface
Compact Flash
Type-II Socket
REAR
HS-862 User’s Manual
9
Page 10
p
1.4 Block Diagram
Intel Socket 370 Tualatin/Coppermine
FC-PGA2/FC-PGA Pentium-III / Celeron
VIA Socket 370 C3 Samuel I/II, Ezra CPU
FSB 66/100/133 MHz
CRT
LCD
LAN
ATAPI Device
CompactFlash
USB Devices
AT, PS/2 K/B
PS/2 Mouse
Floppy
LVDS/TTL
10/100 Mb
UltraATA100
s
RTL8100B
LAN
Codec
S3-VIA
PN133T
N/B
PCI Bus Interface
VIA
686B
S/B
PC133
ISA Bus Interface
One 144-pin SO-DIMM
Sockets up to 512
MBytes PC133 SDRAM
ISA Backplane
Parallel Device
10
Serial Device
Audio Devices
HS-862 User’s Manual
Page 11
R
Chapter 2. Hardware Setup
This chapter contains the information for the installation of hardware. The
install procedure includes jumper settings, CPU and memory installation, fan,
I/O and panel connections.
2.1 Jumper and Connector Location
CDIN
JWOL
JI
JUSB1
JUSB2
JAUDIO
JCOM2
JRTC
FDD
LPT
IDE1
PWRCON JPS JVGA CN_INVERT JATKB
SYSFAN VGA LAN COM1 PS2
JLAN
JP6
CN-LVDS2
CN_LVDS1
JWDT
JVOLT2
JVOLT1
CN_LCD
CPU
CPUFAN
IDE2
JDOM JCFSEL JFRNT
HS-862 User’s Manual
11
Page 12
2.1.1 Jumper Reference
Jumper Function Section
JRTC CMOS Setting 2.3
JWDT Watchdog Timer Mode Setting 2.4
SWDT Time Out Value of Watchdog Timer Setting 2.4
JCFSEL CompactFlash Card (CFC) Mode Setting 2.5.1
JDOM DiskOnModule (DOM) Power Setting 2.5.2
JVOLT1 Flat Panel’s Voltage Setting 2.7.2
JVOLT2 Flat Panel’s Power Setting 2.7.2
JLAN LAN Enable/Disable Setting 2.8
12
HS-862 User’s Manual
Page 13
2.1.2 Connector Reference
Internal Onboard Connector
Connector Function Remark
CPU CPU Socket PGA370 Standard
DIMM 144-pin SO-DIMM Socket Standard
IDE1 40-pin Primary IDE Port Standard
IDE2 44-pin Secondary IDE Port Standard
FDD 34-pin Floppy Port Standard
LPT (PRINTER) 26-pin Parallel Port Standard
JUSB1 10-pin 1st / 2nd USB Port Standard
JUSB2 10-pin 3rd / 4th USB Port Standard
JCOM2 10-pin COM2 RS232 Serial Port Standard
CF CompactFlash Socket Standard
JATKB 5-pin AT Keyboard Connector Standard
SIR 5-pin SIR IrDA Port Standard
PWRCON 6-pin AT/P8 Power Connector Standard
JPS 3-pin ATX Signal Connector Standard
JFRNT 14-pin Front Panel Connector Standard
CPUFAN 3-pin CPU Fan Connector Standard
SYSFAN 3-pin System Fan Connector Standard
JVGA 16-pin Internal VGA Port Standard
JAUDIO 10-pin Audio Port Standard
CDIN 4-pin CD-in Interface Standard
JWOL 3-pin Wake-On-LAN Connector Standard
CN_INVERT 5-pin Backlight Inverter power connector Standard
JLCD 50-pin TTL LCD Interface Standard
JLVDS1/2 20-pin LVDS LCD Interface Standard
External Connector on Bracket
Connector Function Remark
VGA DB15 Female VGA Connector Standard
LAN RJ45 LAN Connector with LED Standard
COM1 DB9 Male COM1 Connector Standard
PS2 6-pin MiniDIN PS/2 Keyboard & Mouse Standard
HS-862 User’s Manual
13
Page 14
2.2 CPU and DRAM Setting
The board is based on Intel socket 370 Pentium-III / Celeron architecture
supports Intel FC-PGA and VIA C3 CPUs at 66/100/133 MHz of FSB. The
FSB, ratio and voltage of CPU is default set by CPU without any additional
jumper selection. The CPU should be installed into the CPU ZIF socket.
The board supports PC100/133 SDRAM up to 512MBytes of memory
capacity on One 144-pin SO-DIMM sockets.
2.3 CMOS Setting
The board’s data of CMOS can be setting in BIOS. If the board refuses to
boot due to inappropriate CMOS settings, here is how to proceed to clear
(reset) the CMOS to its default values.
Jumper: JRTC
Type: onboard 3-pin header
JRTC Mode
1-2 Clear CMOS
2-3 Normal Operation
Default setting
JRTC
1
3
14
HS-862 User’s Manual
Page 15
2.4 Watchdog Timer Setting
The watchdog timer makes the systems auto-reset while it stop to work for
a period. The onboard watchdog timer can be set as system reset or active
NMI mode by jumper JWDT; the timeout value can be set as 1, 2, 10, 20,
110, or 220 seconds by jumper SWDT.
Jumper: JWDT
Type: onboard 3-pin header
JWDT Watchdog Timer
1-2 Active NMI
2-3 Reset
Default setting
JWDT
1
Jumper: SWDT
Type: onboard 4-button / 2-level DIP switch
Timeout Value SWDT 1 2 3 4
1 Second OFF OFF ON OFF
2 Seconds OFF OFF ON ON
10 Seconds OFF ON OFF OFF
20 Seconds OFF ON OFF ON
110 Seconds ON OFF OFF OFF
220 Seconds ON OFF OFF ON
Default setting
SWDT
ON DIP
1234
HS-862 User’s Manual
15
Page 16
2.5 Embedded Solid State Flash Disk
The board supports both of CompactFlash and DOM (DiskOnModule)
embedded flash disk. The onboard CompactFlash socket supports the
IDE-based, driver free and bootable CFC (CompactFlash Card) with jumper
selectable Master / Slave mode on primary IDE channel. The IDE port also
supports DOM (DiskOnModule) or M-systems DiskOnChip IDE Pro flash disk
with jumper selectable Vcc power input for power cable free DOM on
secondary IDE port.
2.5.1 CompactFlash Mode Setting
Jumper: JCFSEL
Type: onboard 3-pin header
JCFSEL CompactFlash Mode (IDE1)
1-2 Master
2-3 Slave
Default setting
JDOM
12
1
JCFSEL
2.5.2 DiskOnModule or DiskOnChip 2000 IDE Pro
Jumper: JDOM
Type: onboard 2-pin header
JDOM DiskOnModule Power Setting
OFF (Open) Normal (without Vcc on pin-20 of IDE2)
ON (Close) DOM (with Vcc on pin-20 of IDE2)
Default setting
16
HS-862 User’s Manual
Page 17
2.6 Power and Fan Connector
Connector: PWRCON
Type: 6-pin AT P8 power connector
Pin Description Pin Description
1 Power Good 4 -12V
2 Vcc 5 Ground
3 +12V 6 Ground
Connector: JPS
Type: 3-pin ATX function connector
Pin Description Pin Description Pin Description
1 5V Standby 2 Ground 3 Power On
Connector: CPUFAN, SYSFAN
Type: 3-pin fan power wafer connector
Pin Description Pin Description Pin Description
1 Ground 2 +12V 3 Fan Control
PWRCON
123456
SYSFAN
13
JPS
1 3
CPUFAN
123
3 1
HS-862 User’s Manual
17
Page 18
2.7 VGA Interface
2.7.1 Standard Analog VGA Interface
The board is integrated with VIA/S3 Twister-T PN133T chipset built-in S3
Savage4 3D SVGA core with BIOS selectable 8/16/32 MBytes video
memory shared with system memory.
Connector: JVGA
Type: 16-pin (2 x 8) 2.54-pitch pin header
Pin Description Pin Description
1 Red 9 Green
2 Blue 10 N/C
3 Ground 11 Ground
4 Ground 12 Ground
5 N/C 13 Ground
6 N/C 14 Data
7 HSYNC 15 VSYNC
8 Clock 16 N/C
JVGA
19
8 16
18
HS-862 User’s Manual
Page 19
1
2.7.2 Digital VGA Interface
The board provides the LCD Interface with VIA/S3 Twister-T PN133T
chipset built-in S3 Savage4 VGA controller and 18-bit Dual-channel LVDS
/ TTL interface for TFT and DSTN LCD panel.
CN_INVERT
JVOLT1 1JVOLT2
2
1
JLCD
50
49
Jumper: JVOLT1
Type: onboard 3-pin header
JVOLT1 LCD Voltage Setting
1-2 +5V
2-3 +3.3V
Default setting
Jumper: JVOLT2
Type: onboard 3-pin header
JVOLT2 LCD Power Sequence Control
1-2 Power Input Directly
2-3 Power Sequence Control by Chipset
Default setting
1
5
HS-862 User’s Manual
19
Page 20
TTL TFT/DSTN LCD Interface
Connector: CN_LCD
Type: onboard 50-pin (2 x 25) 2.0-pitch pin header
Pin Signal Pin Signal
1 ENAVDD 2 ENAVEE
3 GND 4 GND
5 VCC (LCD) 6 Vcc (LCD)
7 GND 8 GND
9 P0 10 P1
11 P2 12 P3
13 P4 14 P5
15 P6 16 P7
17 P8 18 P9
19 P10 20 P11
21 P12 22 P13
23 P14 24 P15
25 P16 26 P17
27 P18 28 P19
29 P20 30 P21
31 P22 32 P23
33 P24 34 P25
35 SHFCLK 36 FLM
37 M 38 LP
39 GND 40 GND
41 P26 42 P27
43 P28 44 P29
45 P30 46 P31
47 P32 48 P33
49 P34 50 P35
20
HS-862 User’s Manual
Page 21
LVDS TFT/DSTN LCD Interface
Connector: JLVDS1, JLVDS2
Type: onboard 20-pin Hirose DF13-20DP-1.25V
Pin Signal Pin Signal
1 LCD_Vcc 2 LCD_Vcc
3 GND 4 GND
5 TX0- 6 TX0+
7 GND 8 TX1-
9 TX1+ 10 GND
11 TX2- 12 TX2+
13 GND 14 TCLK15 TCLK+ 16 GND
17 N/C 18 N/C
19 GND 20 GND
LCD Backlight Inverter Power Connector
Connector: CN_INVERT
Type: 5-pin wafer connector
Pin Description
1 +12V
2 Ground
3 Ground
4 Ground
5 ENABKL
HS-862 User’s Manual
21
Page 22
BIOS Configuration for LCD
The selection of display type for flat panel depends on the LCD display you
use. Please entry the “Advanced Chipset Features” screen on the main
screen and find the item of “Panel Type”, and set it with the specification of
the flat panel.
LCD Type Support LCD
00 640x480 TFT
01 800x600 TFT
02 1024x768TFT 2 pixel/clk at 32MHz
03 1280x1024 TFT
04 640x480 DSTN
05 800x600 DSTN
06 1024x768 DSTN
07 1024x768 TFT 1 pixel/clk at 65MHz
08 640x480 TFT
09 800x600 TFT
22
0A 1024x768 TFT
0B 1280x1024 TFT / Pixel
0C 1400x1050 TFT
0D 800x600 DSTN
0E 1024x768 DSTN
0F 1280x1024 DSTN
Default setting
HS-862 User’s Manual
Page 23
2.8 Ethernet Interface
The board integrated with 10/100BASE-TX Fast Ethernet interface at the type
of 10Base-T/100Base-TX auto-switching Fast Ethernet with full duplex and
IEEE 802.3U compliant. The LAN controller, RTL8100B provides the powerful
Fast Ethernet interface with embedded operating system (OS) supported,
green function (power saving mode / wake-on-LAN) and advanced network
management functions.
Jumper: JLAN
Type: onboard 3-pin header
JLAN LAN Interface
1-2 Enable
2-3 Disable
Default setting
Connector: JWOL
Type: onboard 3-pin header wafer connector
Pin 1 2 3
Description +5V Standby Ground WOL-Ctrl
JWOL
321
JLAN
HS-862 User’s Manual
23
Page 24
2.9 Audio Interface
The board integrates with AC97 3D audio interface VIA 686B with Realtek
ALC201A code that provides line-in, line-out, Mic-in and CD-in interfaces for
industrial applications with audio function.
Connector: JAUDIO
Type: 10-pin (2 x 5) 2.54-pitch pin header
Pin Description Pin Description
1 Line – Right 2 Ground
3 Line – Left 4 MIC
5 MIC 6 Ground
7 N/C 8 Line Out – Left
9 Line Out – Right 10 Ground
Connector: CDIN (CD Audio Input Interface)
Type: 4-pin (1 x 4) 2.54-pitch wafer connector
Pin Description
1 CD – LEFT
2 Ground
3 Ground
4 CD – RIGHT
CDIN
14
JAUDIO
2
10
9
24
HS-862 User’s Manual
Page 25
2.10 Switch and Indicator
1
13
Connector: JFRNT
Type: onboard 14-pin (2 x 7) 2.54-pitch pin header
Function Signal PIN Signal Function
2
14
JFRNT
IDE LED
Vcc (+) 1 2 (+) Vcc
Active 3 4 N/C
Reset 5 6 GND
Reset
GND 7 8 Vcc
Power
Button
HS-862 User’s Manual
PWRBT 11 12 N/C
GND 13
Power
LED
N/C 9 10 N/C
Speaker
14 SPKIN
25
Page 26
Notes (This page left blank intentionally)
26
HS-862 User’s Manual
Page 27
Chapter 3. BIOS Setup
The single board computer uses the Award BIOS for the system configuration.
The Award BIOS in the single board computer is a customized version of the
industrial standard BIOS for IBM PC AT-compatible computers. It supports
Intel x86 and compatible CPU architecture based processors and computers.
The BIOS provides critical low-level support for the system central processing,
memory and I/O sub-systems.
The BIOS setup program of the single board computer let the customers
modify the basic configuration setting. The settings are stored in a dedicated
battery-backed memory, NVRAM, retains the information when the power is
turned off. If the battery runs out of the power, then the settings of BIOS will
come back to the default setting.
The BIOS section of the manual is subject to change without notice and is
provided here for reference purpose only. The settings and configurations of
the BIOS are current at the time of print, and therefore they may not be
exactly the same as that displayed on your screen.
To activate CMOS Setup program, press ＜DEL＞ key immediately after you
turn on the system. The following message “Press DEL to enter SETUP”
should appear in the lower left hand corner of your screen. When you enter
the CMOS Setup Utility, the Main Menu will be displayed as Figure 3-1. You
can use arrow keys to select your function, press ＜Enter＞ key to accept
the selection and enter the sub-menu.
Figure 3-1. CMOS Setup Utility Main Screen
Phoenix – Award BIOS CMOS Setup Utility
>Standard CMOS Features >Frequency/Voltage Control
>Advanced BIOS Features Load Fail-Safe Defaults
>Advanced Chipset Features
>Integrated Peripherals
>Power Management Setup Set User Password
>PnP / PCI Configurations Save & Exit Setup
>PC Health Status Exit Without Saving
Esc : Quit ↑ ↓ → ← : Select Item
F10 : Save & Exit Setup
Load Optimized Defaults
Set Supervisor Password
HS-862 User’s Manual
27
Page 28
3.1 Advanced Chipset Feature
The display interface of the board can be setup in the BIOS with the
selections including the video memory, display type and LCD type. In the
section of “Advanced Chipset Features” on the main screen, there are three
items of “Frame Buffer Size”, “Display Device” and “LCD Type” to set the
capacity of video memory, display device and specification of the flat panel.
Figure 3.2 - Advanced Chipset Features Screen
Phoenix – Award BIOS CMOS Setup Utility
Advanced Chipset Features
DRAM Timing By SPD [Enabled] Item Help
X DRAM Clock [Host CLK]
X SDRAM Cycle Length 3 Menu Level ►
X Bank Interleave [Disabled]
Memory Hole [Disabled]
P2C/C2P Concurrency [Enabled]
System BIOS Cacheable [Enabled]
Video RAM Cacheable [Enabled]
Frame Buffer Size [16M]
AGP Aperture Size [64M]
AGP-4X Mode [Enabled]
AGP Driving Control [Auto]
AGP Driving Value DA
Display Device [CRT]
LCD Type 07
OnChip USB [Enabled]
USB Keyboard Support [Disabled]
USB Mouse Support [Disabled]
OnChip Sound [Auto]
CPU to PCI Write Buffer [Enabled]
PCI Dynamic Bursting [Enabled]
PCI Master 0 WS Write [Enabled]
PCI Delay Transaction [Disabled]
PCI#2 Access #1 Retry [Disabled]
AGP Master 1 WS Write [Disabled]
AGP Master 1 WS Read [Disabled]
↑ ↓ → ←:Move Enter:Select +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help
F5 : Previous Value F6 : Fail-Safe Defaults F7 : Optimized Defaults
28
HS-862 User’s Manual
Page 29
3.2 Frame Buffer Size
The item of “Frame Buffer size” offers the selection of the capacity of video
memory shared with system memory including 2, 4, 8, 16, and 32 MBytes.
Selection Frame Buffer Size
2M 2 MBytes of Video Memory
4M 4 MBytes of Video Memory
8M 8 MBytes of Video Memory
16M 16 MBytes of Video Memory
32M 32 MBytes of Video Memory
Default Setting
3.3 Display Device
The item of “Display Device” offers the selection of the display type. The
selections include Auto, CRT, LCD, CRT+LCD.
Selection Support Display Type
Auto Auto Detect
CRT CRT Display
LCD LCD Panel
CRT+LCD Both of CRT and LCD Panel
Default Setting
Please notice that if the systems are connecting with the KVM data switch,
the selection of display device should be “CRT” or “CRT+LCD” because
the system will detect the display every time when you change the channel
of the KVM data w\switch if it’s setting as “auto”.
HS-862 User’s Manual
29
Page 30
3.4 LCD Type
The item of “LCD Type” offers the selection of the LCD type. Please check
the LCD you want to use and select the right LCD type, saving and restart
the computer.
LCD Type Support Function
00 640x480 TFT
01 800x600 TFT
02 1024x768TFT 2pixel/clk at 32Mhz
03 1280x1024 TFT
04 640x480 DSTN
05 800x600 DSTN
06 1024x768 DSTN
07 1024x768 TFT 1pixel/clk at 65Mhz
08 640x480 TFT
09 800x600 TFT
0A 1024x768 TFT
0B 1280x1024 TFT
0C 1400x1050 TFT 2pixel/clk at 54Mhz
0D 800x600 DSTN
0E 1024x768 DSTN
0F 1280x1024 DSTN
Default Setting
30
HS-862 User’s Manual
Page 31
Chapter 4. Driver Installation
The driver CD offers auto-run menu. It will detect and select the type of single
board computer and helps you install the drivers automatically.
Install Related Chipset INF Driver
The selection helps you to install the INF of related chipset interface.
Install VGA Driver
The selection helps you to install the driver of onboard VGA interface.
Install LAN Driver
The selection helps you to install the driver of onboard LAN interface.
Install Audio Driver
The selection helps you to install the driver of onboard audio interface.
Link to < Website > Homepage
The selection helps you to link to the website to find the updated technical
documents and download directly.
Browse this CD
The selection helps you to find the drivers in this CD directly.
HS-862 User’s Manual
31
Page 32
Notes (This page left blank intentionally)
32
HS-862 User’s Manual
Page 33
Appendix A. I/O Port Pin Assignment
A.1 IDE Port
Connector: IDE1, IDE2
Type: 40-pin box header
Pin Description Pin Description
1 Reset 2 Ground
3 D7 4 D8
5 D6 6 D9
7 D5 8 D10
9 D4 10 D11
11 D3 12 D12
13 D2 14 D13
15 D1 16 D14
17 D0 18 D15
19 Ground 20 N/C (Vcc) *
21 REQ 22 Ground
23 IOW-/STOP 24 Ground
25 IOR-/HDMARDY 26 Ground
27 IORDY/DDMARDY 28 IDESEL
29 DACK- 30 Ground
31 IRQ 32 N/C
33 A1 34 CBLID
35 A0 36 A2
37 CS0 (MASTER CS) 38 CS1 (SLAVE CS)
39 LED ACT- 40 Ground
* Jumper selectable Vcc power on IDE2 port for power cable free DOM
(DiskOnModule).
2
1
40
39
HS-862 User’s Manual
33
Page 34
A.2 Floppy Port
Connector: FDD
Type: 34-pin (2x 17) 2.54-pitch box header
Pin Description Pin Description
1 Ground 2 DRIVE DENSITY SELECT 0
3 Ground 4 DRIVE DENSITY SELECT 1
5 Ground 6 N/C
7 Ground 8 INDEX9 Ground 10 MOTOR ENABLE A11 Ground 12 DRIVER SELECT B13 Ground 14 DRIVER SELECT A15 Ground 16 MOTOR ENABLE B17 Ground 18 DIRECTION19 Ground 20 STEP21 Ground 22 WRITE DATA23 Ground 24 WRITE GATE25 Ground 26 TRACK 027 Ground 28 WRITE PROTECT29 Ground 30 READ DATA31 Ground 32 HEAD SELECT33 Ground 34 DISK CHANGE-
2
1
34
33
34
HS-862 User’s Manual
Page 35
A.3 Parallel Port
Connector: LPT (PRINTER)
Type: 26-pin (2 x 13) 2.54-pitch box header
Pin Description Pin Description
1 STROBE- 14 AUTO FEED2 D0 15 ERROR3 D1 16 INITIALIZE4 D2 17 SELECT INPUT5 D3 18 Ground
6 D4 19 Ground
7 D5 20 Ground
8 D6 21 Ground
9 D7 22 Ground
10 ACKNOWLEDGE- 23 Ground
11 BUSY 24 Ground
12 PAPER EMPTY 25 Ground
13 SELECT+ 26 N/C
14
26
1
13
HS-862 User’s Manual
35
Page 36
2
A.4 RS-232 Serial Port
A.4.1 Onboard RS-232 Serial Port
Connector: JCOM2
Type: 10-pin (2 x 5) 2.54-pitch box header
Pin Description Pin Description
1 DCD 2 RXD
3 TXD 4 DTR
5 Ground 6 DSR
7 RTS 8 CTS
9 RI 10 N/C
A.4.2 On Bracket RS-232 Serial Port
Connector: COM1
Type: 9-pin D-sub male connector on bracket
Pin Description Pin Description
1 DCD 2 RXD
3 TXD 4 DTR
5 Ground 6 DSR
7 RTS 8 CTS
9 RI
10
1
5
4
3
2
1
9
9
8
7
6
36
HS-862 User’s Manual
Page 37
6
A.5 USB Port
Connector: JUSB1, JUSB2
Type: 10-pin (2 x 5) 2.54-pitch pin header for dual USB Ports
Pin Description Pin Description
1 Vcc 6 Vcc
2 Data0- (Data2-) 7 Data1- (Data3-)
3 Data0+ (Data2+) 8 Data1+ (Data3+)
4 Ground 9 Ground
5 Ground 10 N/C
A.6 IrDA Port
Connector: SIR
Type: 5-pin (1 x 5) 2.54-pitch pin header
Pin Description
1 Vcc
2 N/C
3 IRRX
4 Ground
5 IRTX
A.7 VGA Port
Connector: VGA
Type: 15-pin D-sub female connector on bracket
Pin Description Pin Description Pin Description
1 RED 6 Ground 11 N/C
2 GREEN 7 Ground 12 VDDAT
3 BLUE 8 Ground 13 HSYNC
4 N/C 9 Vcc 14 VSYNC
5 Ground 10 Ground 15 VDCLK
10
1
5
1
6
1
2
3
4
5
10
11
12
13
14
15
HS-862 User’s Manual
37
Page 38
1
A.8 LAN Port
Connector: LAN
Type: RJ45 connector on bracket
Pin 1 2 3 4 5 6 7 8
Description TX+ TX- RX+ N/C N/C RX- N/C N/C
8
A.9 AT Keyboard Port
Connector: JAT_KB
Type: 5-pin box header
Pin 1 2 3 4 5
Description CLK DATA N/C Ground Vcc
A.10 PS/2 Keyboard and Mouse Port
Connector: PS2
Type: 6-pin MiniDIN connector on bracket
Pin 1 2 3 4 5 6
Description KBD MSD Ground N/C KBC MSC
Note: The PS/2 connector supports standard PS/2 keyboard directly or both PS/2
keyboard and mouse through the PS/2 Y-type cable. The cable is the standard on
packing list.
1
5
3
1
5
6
2
4
38
HS-862 User’s Manual
Page 39
Appendix B. Flash the BIOS
B.1 BIOS Auto Flash Tool
The board is based on Award BIOS and can be updated easily by the BIOS
auto flash tool. You can download the tool online at the address below:
http://www.award.com
http://www.commell.com.tw/Support/Support_SBC.htm
File name of the tool is “awdflash.exe”, it’s the utility that can write the data
into the BIOS flash ship and update the BIOS.
B.2 Flash Method
1. Get the “.bin” file including the image of new BIOS you want to update.
2. Power on the system and flash the BIOS.
3. Re-star the system.
Any question about the BIOS re-flash please contact your distributors or visit
our website at below:
http://www.commell.com.tw/Support/Support_SBC.htm
HS-862 User’s Manual
39
Page 40
Notes (This page left blank intentionally)
40
HS-862 User’s Manual
Page 41
Appendix C. System Resource
C.1 I/O Port Address Map
Address Range Device Bus Type
0060-0060 i8042prt 0 ISA
0064-0064 i8042prt 0 ISA
0170-0170 viadsk 0 ISA
01CE-01CF VgaSave 0 PCI
01F0-01F7 viadsk 0 ISA
02F8-02FE Serial 0 ISA
0376-0376 viadsk 0 ISA
0378-037A Parport 0 ISA
03B0-03BB VgaSave 0 PCI
03C0-03CF S3Inc 1 PCI
03C0-03DF VgaSave 0 PCI
03D4-03DB S3Inc 1 PCI
03F0-03F5 Floppy 0 ISA
03F6-03F6 viadsk 0 ISA
03F7-03F7 Floppy 0 ISA
03F8-03FE Serial 0 ISA
D000-D007 viadsk 0 ISA
D008-D00F viadsk 0 ISA
DC00-DCFF alcxnt 0 PCI
E000-E003 alcxnt 0 PCI
E800-E8FF alcxnt 0 PCI
HS-862 User’s Manual
41
Page 42
C.2 Memory Address Map
Range Device
00000000 - 0009FFFF System board extension for PnP BIOS
000A0000 - 000AFFFF S3 Graphics Twister
000B0000 - 000BFFFF S3 Graphics Twister
000C0000 - 000CDFFF S3 Graphics Twister
000CE000 - 000CFFFF Motherboard resources
000F0000 - 000F3FFF Motherboard resources
000F4000 - 000F7FFF Motherboard resources
000F8000 - 000FFFFF Motherboard resources
00100000 - 00FFFFFF System board extension for PnP BIOS
E0000000 - E7FFFFFF VIA CPU to AGP Controller
E0000000 - E7FFFFFF S3 Graphics Twister
E8000000 - EBFFFFFF VIA Standard CPU to PCI Bridge
EC000000 - EC00FFFF S3 Graphics Twister
EC000000 - EDFFFFFF VIA CPU to AGP Controller
ED000000 - ED07FFFF S3 Graphics Twister
EF000000 - EF0000FF Realtek RTL8139(A/B/C/8130) PCI Fast Ethernet NIC
FEE00000 - FEE0FFFF System board extension for PnP BIOS
FFFE0000 - FFFFFFFF System board extension for PnP BIOS
42
HS-862 User’s Manual
Page 43
C.3 IRQ and DMA Resource
C.3.1 IRQ
IRQ Number Device
0 System timer
1 Standard 101/102-Key or Microsoft Natural Keyboard
2 Programmable interrupt controller
3 Communications Port (COM2)
4 Communications Port (COM1)
5 Reserved
6 Standard Floppy Disk Controller
7 Printer Port (LPT1)
8 System CMOS/real time clock
9 Avance AC'97 Audio for VIA (R) Audio Controller
9 IRQ Holder for PCI Steering
10 S3 Graphics Twister
10 IRQ Holder for PCI Steering
11 VIA Tech 3038 PCI to USB Universal Host Controller
11 IRQ Holder for PCI Steering
12 PS/2 Compatible Mouse Port
13 Numeric data processor
14 Primary IDE controller (dual fifo)
14 VIA Bus Master PCI IDE Controller
15 Secondary IDE controller (dual fifo)
15 VIA Bus Master PCI IDE Controller
HS-862 User’s Manual
43
Page 44
C.3.2 DMA
Channel Device
0 (free)
1 (free)
2 Standard Floppy Disk Controller
3 (free)
4 Direct Memory Access Controller
5 (free)
6 (free)
7 (free)
44
HS-862 User’s Manual
Page 45
Notes (This page left blank intentionally)
HS-862 User’s Manual
45
Page 46
Contact Information
Any advice or comment about our products and service, or anything we can help you
please don’t hesitate to contact with us. We will do our best to support you for your products,
projects and business.
COMMELL Industrial Computer
Taiwan Commate Computer Inc.
COMMELL
Your Embedded Applied Computer Partner
Address
TEL +886-2-26963909
FAX +886-2-26963911
Website http://www.commell.com.tw
E-mail info@commell.com.tw
Authorized Distributor
8F, No. 94, Sec. 1, Shin Tai Wu Rd., Shi Chih
Taipei Hsien, Taiwan
tech@commell.com.tw (Technical Support)
www.commell.com.tw
(General Information)
46
HS-862 User’s Manual
Loading...