Commell HS-774 User Manual

Page 1
HS-774
Half-size PCI Bus CPU Card
User’s Manual
Edition 1.6
2015/05/20
Page 2
Page 3
HS-774 User’s Manual
-1-
Copyright
Copyright 2012, all rights reserved. This document is copyrighted and all rights are reserved. The information in this document is subject to change without prior notice to make improvements to the products. This document contains proprietary information and pr otected by copyright. No part of this document may be reproduced, copied, or translated in any form or any means without prior written permission of the manufacturer. All trademarks and/or registered trademarks contains in this document are propert y of their respective owners.
Disclaimer
The company shall not be liable for any incidental or consequential damages resulting from the performance or use of this product. The company does not issue a warranty of any kind, express or implied, including without limitation implied warranties of merchantability or fitness for a particular purpose. The company has the right to revise the manual or include changes in the specifications of the product described within it at any time without notice and without obligation to notify any person of such revision or changes.
Trademark
All trademarks are the property of their respective holders.
Any questions please visit our website at TUhttp://www.commell.com.twUT
Page 4
HS-774 User’s Manual
-2-
Dual COM PORT cable x 1 (OALES-BKU2)/ (1040087)
Packing List:
Please check the package content before you starting using the board.
Hardware:
HS-774 Half-size PCI Bus CPU Card x 1
Cable Kit:
SATA Cable x 2
(OALSATA3-L)/ (1040529)
Printed Matters:
Driver CD (Including User’s Manual) x 1
Audio Cable x 1
(OALPJ-HD)/ (1040120)
CPU Cooler x 1
(OHS-P-M-H)/ (1190058)
USB2.0 Cable x 1
(OALUSBA-1)/ (1040172)
PS/2 Keyboard & Mouse Cable x 1
(OALPS2/MKN)/ (1040551)
4-pin to 3-pin ATX cable x 1
(OAL-ATX-C)/ (1040184)
DVI VGA Cable x 1
(OALDVIVGA)/ (1040078)
USB3.0 Cable
(OALUSB3)/ (1040531)
Optional:
Page 5
HS-774 User’s Manual
-3-
Index
Chapter 1 <Introduction>.............................................................6
1.1 <Product Overview>..................................................................................... 6
1.2 <Product Specification>................................................................................7
1.3 <Mechanical Drawing>.................................................................................8
1.4 <Block Diagram>..........................................................................................9
Chapter 2 <Hardware Setup>..................................................10
2.1 <Connector Location>................................................................................ 10
2.2 <Jumper Location & Reference>................................................................ 11
2.3 <Connector Reference>............................................................................. 12
2.3.1 <Internal Connectors>..............................................................12
2.3.2 <External Connectors>............................................................. 12
2.4 <CPU and Memory Setup>........................................................................13
2.4.1 <CPU Setup>.............................................................................13
2.4.2 <Memory Setup>.......................................................................14
2.5 <CMOS & ATX Setup>............................................................................... 15
2.6 <Serial ATA Interface>................................................................................ 16
2.7 <Ethernet Interface>...................................................................................17
2.8 <Onboard Display Interface> ..................................................................... 18
2.8.1 <Analog Display>.......................................................................18
2.8.2 <Digital Display>........................................................................19
2.9 <Integrated Audio Interface>...................................................................... 23
2.10 <USB Interface>....................................................................................... 24
2.11 <Serial Port>.............................................................................................26
2.12 <PCIE Mini Card and SIM Interface>.......................................................28
2.12.1 <SIM Setup>............................................................................30
2.13 <GPIO and SMBUS Interface>.................................................................32
2.14 <Power Supply and Fan Interface >......................................................... 33
2.14.1 <Power Input>..........................................................................33
2.15 <Switch and Indicator>.............................................................................34
Page 6
HS-774 User’s Manual
-4-
Chapter 3 <System Setup>.......................................................35
3.1 <Audio Configuration>................................................................................35
3.2 <Display Properties Setting> ......................................................................36
3.3 <SATA configuration>.................................................................................38
3.4 <SATA RAID Configuration>.......................................................................39
Chapter 4 <BIOS Setup>.............................................................41
Appendix A <I/O Port Pin Assignment>..........................43
A.1 <Serial ATA Port>.......................................................................................43
A.2 <IrDA Port>.................................................................................................43
A.3 <VGA Port>................................................................................................43
A.4 <LAN Port>.................................................................................................43
A.5 <LAN LED Port>.........................................................................................44
Appendix B <Flash BIOS> .........................................................45
B.1 <Flash Tool>...............................................................................................45
B.2 <Flash BIOS Procedure> ...........................................................................45
Appendix C <Programming GPIO’s >...............................46
Appendix D <Programming Watchdog Timer >.........47
Contact Information.......................................................................48
Page 7
HS-774 User’s Manual
-5-
(This page is left for blank)
Page 8
HS-774 User’s Manual
-6-
Chapter 1 <Introduction>
1.1 <Product Overview>
HS-774 the 3rd Generation Intel of the Half-size PCI Bus CPU Card, supports 3rd
Generation Intel® Core™ i7, Core™ i5, Core™ i3 Mobile Processor and features Intel QM77 chipset, integrated HD Graphics, DDR3 memory, REALTEK High Definition Audio, Serial ATA with RAID function for a system and Intel Gigabit LAN.
Intel Ivy Bridge Processor
The 3rd Generation Intel® Core™ processor family mobile is the next generation of 64-bit, multi-core mobile processor built on 22- nanometer process technology. Based on a new micro-architecture.
New features for Intel QM77 chipset
The board integrates Intel QM77 chipset, supports integrated HD Graphics, built-in high speed mass storage interface of Serial ATA interface with RAID function, High Definition Audio with 2 channels surrounding sound.
All in One multimedia solution
Based on Intel QM67 chipset, the board provides high performance onboard gra phics, 24-bit dual channel LVDS interface, DVI-I and 2 channels High Definition Audio, to meet the very requirement of the multimedia application.
Flexible Extension Interface
The board provides, two mini-PCIE socket and PCI bus.
Page 9
HS-774 User’s Manual
-
7-
1.2 <Product Specification>
General Specification
Form Factor Half-size PCI Bus CPU Card CPU 3rd Generation Intel® Core™ i7, Core™ i5, Core™ i3 Mobile Processor
Package type: rPGA988B
Memory 2 x DDRIII SO-DIMM 1066/1333/1600 MHz up to 16GB
Support Non-ECC, unbuffered memory only
Chipset Intel QM77 Real Time Clock Chipset integrated RTC with onboard lithium battery Watchdog Timer Generates a system reset with internal timer for 1min/s ~255min/s Power Management Supports ACPI 3.0 compliant, DVI-I Interface Onboard DVI connector for DVI-I interface LVDS Interface Onboard 24-bit dual channel LVDS connector with +3.3V/+5V/+12V
supply
Serial ATA Interface 2 x serial ATAII interface with 300MB/s transfer rate
2 x serial ATAIII interface with 600MB/s transfer rate Support RAID 0, 1, 5, 10 and Intel Rapid Storage Technology
Audio Interface Realtek ALC888 HD Audio LAN Interface 1 x Intel 82579LM Gigabit LAN (Support iAMT8.0)
1 x Intel 82574L Gigabit LAN
GPIO interface Onboard programmable 8-bit Digital I/O interface Extended Interface 2 x PCIE mini card socket, 1 x SIM socket
(Optional support mSATA(SATAII) for Mini_Card1)
Internal I/O Port 5 x RS232, 1 x RS232/422/485, 1 x SMBUS, 1 x GPIO, 4 x USB3.0 ports,
2 x USB2.0 ports, 1 x IrDA, 1 x VGA, 1 x LVDS, 2 x Serial ATAII, 2 x Serial ATAIII, 1 x Front panel Audio and 1 x CDIN
External I/O Port 1 x DVI-I Port, 2 x RJ45 and 1 x PS/2 Keyboard/Mouse Port Power Requirement DC 5V/12V power required, optional 5VSB for ATX
Onboard 4-pin power connector & 3-pin ATX connector
Dimension 185mm x 122mm Temperature Operating within 0~60 centigrade
Storage within –20~85 centigrade
Ordering Code
HS-774TXDG2 Intel PGA988B + QM77 Onboard VGA, LVDS, DVI, LAN, USB2.0,
USB3.0, HD Audio, SATAII ,SATAIII, SMBUS, LPC, IrDA, SIM, GPIO and PCI Express mini card
HS-774TXDG2S Intel PGA988B + QM77 Onboard VGA, LVDS, DVI, LAN, USB2.0,
USB3.0, HD Audio, SATAII ,SATAIII, SMBUS, LPC, IrDA, GPIO PCI Express mini card and mSATA
The specifications may be different as the actual production. For further product information please visit the website at
TUhttp://www.commell.com.twUT
Page 10
HS-774 User’s Manual
-
8-
1.3 <Mechanical Drawing>
Page 11
HS-774 User’s Manual
-
9-
1.4 <Block Diagram>
QM77
1 x Intel 82579LM 1 x Intel 82574L
1 x RS232/422/485 1 x COM & GPIO & IrDA
3rd Generation Intel® Core™ i7, Core™ i5, Core™ i3 Mobile Processor
2 x 204-pin DDR3 SO-DIMM 1066/1333/1600 MHz up to 16GB
1 x LVDS
2 x Serial ATAIII 2 x Serial ATAII
2 x PCI Express mini card
1 x DVI-I
ALC888 HD Audio
F81216
SI383
PCI Bus
4 x USB3.0 2 x USB2.0
4 x RS232
Page 12
HS-774 User’s Manual
-
10-
Chapter 2 <Hardware Setup>
2.1 <Connector Location>
PS2DVI RJ45_1 RJ45_2
JFRNTCN_PS CN_ATKB
SYSFAN
CN_INV
SO-DIMM1
DC_IN
CN_IR
CD_IN
CN_LVDS
CPUFAN
CN_AUDIO
CN_SMBUS
MINI_CARD1
SO-DIMM2
MINI_CARD2
SIMM CN_DIO
CN_CRT
CN_LPC
CN_USB1
COM 5 / 6
COM 3 / 4
COM 1 / 2
SATA3
SATA1 SATA2
SATA4
CN_USB3-1
CN_USB3-2
Page 13
HS-774 User’s Manual
-
11-
2.2 <Jumper Location & Reference>
Jumper Function
JRTC CMOS Operating/Clear Setting JVLCD Panel Voltage Setting JAT Power mode select JP1 Com1 Voltage Setting (For Pin 9) JP2 Com2 Voltage Setting (For Pin 9) JP3 Com3 Voltage Setting (For Pin 9) JP4 Com4 Voltage Setting (For Pin 9) JCSEL1
JCSEL2
CN_COM2 RS-232 RS422 RS485 Setting CN_IR IrDA Setting
JVUSB USB Voltage Setting
JVLCDJRTC
JAT
JP1 JP2
JVUSB
JP4
JP3
JCSEL1
JCSEL2
Page 14
HS-774 User’s Manual
-
12-
2.3 <Connector Reference>
2.3.1 <Internal Connectors>
Connector Function Remark
CPU Socket rPGA988B for PGA988 CPU SO-DIMM 1/2 204 -pin DDR3 SO-DIMM socket SATA 1/2 7-pin Serial ATAIII connector SATA 3/4 7-pin Serial ATAII connector DC_IN 4-pin power supply connector CN_AUDIO 5 x 2-pin audio connector CD_IN 4-pin CD-ROM audio input connector CN_DIO 6 x 2-pin digital I/O connector CN_USB1 5 x 2-pin USB2.0 connector CN_USB3- 1/2 10 x 2-pin USB3.0 connector CPUFAN 4-pin CPU cooler fan connector SYSFAN 4-pin system cooler fan connector CN_LVDS 20 x 2-pin LVDS connector CN_INV 5-pin LCD inverter connector CN_IR 5-pin IrDA connector CN_COM 1/2 ,3/4, 5/6
19-pin RS232 & RS422/485/232 connector
CN_LPC 5 x 2-pin LPC connector JFRNT
14-pin front panel switch/indicator
connector Mini-PCIE1/2 2 x 52-pin Mini-PCIE socket JAT Power mode select JSPD 1/2 LAN Speed LED connector JACT 1/2 LAN Activity LED connector
2.3.2 <External Connectors>
Connector Function Remark
DVI DVI-I connector RJ45_1/2 RJ45 LAN connector PS/2 PS/2 keyboard and mouse connector
Page 15
HS-774 User’s Manual
-
13-
2.4 <CPU and Memory Setup>
2.4.1 <CPU Setup>
The board comes with the socket rPGA988 for Intel Ivy Bridge Processor, Please follow the instruction to install the CPU properly.
1. Use the flat-type screw drive to unlock the CPU socket
Unlock wa
y
Check point
2. Follow the pin direction to install the processor on the socket
3. Lock the socket
Socket CPU Check point
Page 16
HS-774 User’s Manual
-
14-
2.4.2 <Memory Setup>
The board provides 2 x 204-pin DDR3 SO-DIMM to support 1066/1333/1600MHz DDR3 memory module up to 16GB. Support Non-ECC, unbuffered memory only.
SO-DIMM1
SO-DIMM2
Page 17
HS-774 User’s Manual
-
15-
2.5 <CMOS & ATX Setup>
The board’s data of CMOS can be setting in BIOS. If the board refuses to boot due to inappropriate CMOS settings, here is how to proceed to clear (reset) the CMOS to its default values.
Jumper: JRTC Type: Onboard 3-pin jumper
JRTC Mode
1-2 Clear CMOS 2-3 Normal Operation
Default setting: 2-3
Jumper: JAT Type: onboard 3-pin jumper
JAT Mode
1-2 AT Mode 2-3 ATX Mode
Default setting:2-3
JRTC
1 3
JAT
1 3
Page 18
HS-774 User’s Manual
-
16-
2.6 <Serial ATA Interface>
HS-774 has Two Serial ATA II(SATA Port3/4) & Two Serial ATA III(SATA Port1/2)
interfaces with RAID function, the transfer rate of the Serial ATA II can be up to 300MB/s & Serial ATA III can be up to 600MB/s. Please go to http://www.serialata.org/
for more about Serial ATA technology information. Based on Intel® PCH, it supports Intel® Matrix Storage Technology with combination of RAID 0,1,5 and 10. The main features of RAID on Intel® QM77 PCH are listed below:
1. Supports for up to RAID volumes on a single, two-hard drive RAID array.
2. Supports for two, two-hard drive RAID arrays on any of six Serial ATA ports.
3. Supports for Serial ATA ATAPI devices.
4. Supports for RAID spares and automatic rebuild.
5. Supports on RAID arrays, including NCQ and native hot plug.
For more information please visit Intel’s official website.
For more about the system setup for Serial ATA, please check the chapter of SATA configuration.
SATA Port 1 SATA Port 2 SATA Port 3 SATA Port 4
Page 19
HS-774 User’s Manual
-
17-
2.7 <Ethernet Interface>
The board integrates with one Intel 82574L Gigabit Ethernet & one Intel 82579LM controllers, as the PCI Express bus. The Intel 82574L & 82579LM supports triple speed of 10/100/1000Base-T, with IEEE802.3 compliance and Wake-On-LAN supported.
Onboard Intel® 82579LM GbE controller support Intel® AMT 8.0 feature on primary LAN
port. The BIOS is ready to support Intel® AMT 8.0 feature. The necessary prerequisite is your CPU must support Intel® vPro technology, ex. i7-3610QE For further instruction about the Intel® AMT features and set up, please refer to the iAMT Setting.pdf.
RJ45 LAN connector
82579LM 82574L
Page 20
HS-774 User’s Manual
-
18-
2.8 <Onboard Display Interface>
Based on Intel Ivy Bridge CPU with built-in HD Graphic, the board provides one DB15 on DVI-I real external DVI VGA cable, one 40-pin LVDS interface with 5-pin LCD backlight inverter connector and one DVI-I on bracket inverter connector and one DVI-I on bracket.
2.8.1 <Analog Display>
Please connect your CRT or LCD monitor with DB15 to the DVI VGA cable DB15 female connector on rear I/O port.
Connector: CN_CRT Type: onboard 10-pin connector for CRT connector (Pitch = 2.0mm)
Pin Signal Pin Signal
1 5VCDA 2 5VCLK 3 -CRTATCH 4 BR 5 BG- 6 BB 7 5HSYNC 8 5VSYNC 9 VGAGND 10 VGAGND
DVI-I
DVI
DB15 VGA
1 2
9 10
CN_CRT
Page 21
HS-774 User’s Manual
-
19-
2.8.2 <Digital Display>
The board provides DVI external connector and one 40-pin LVDS connector for 24-bit single/dual channel panels, supports up to 2048 x 1536 (UXGA) resolution, with one LCD backlight inverter connector and one jumper for panel voltage setting.
Effective patterns of connection: 1-2 / 3-4 / 5-6
Warning: others cause damages
1
2
CN_LVDS
40
39
2
1
JVLCD
2
1
5
6
3
4
5
6
5
CN_INV
1
Page 22
HS-774 User’s Manual
-
20-
Connector: CN_INV Connector: JVLCD Type: 5-pin LVDS Power Header Type: 6-pin Power select Header
Pin Description
1 +12V 2 Reserved (Note) 3 GND 4 GND 5 ENABKL
Note: Reserved for MB internal test
Please treat it as NC.
Connector: CN_LVDS Type: onboard 40-pin connector for LVDS connector Connector model: E&T 3950-B40C-00R or similar (HIROSE DF13-40DP-1.25V compatible)
Pin Signal Pin Signal
2 LCDVCC 1 LCDVCC 4 GND 3 GND 6 ATX0- 5 BTX0-
8 ATX0+ 7 BTX0+ 10 GND 9 GND 12 ATX1- 11 BTX1­14 ATX1+ 13 BTX1+ 16 GND 15 GND 18 ATX2- 17 BTX2­20 ATX2+ 19 BTX2+ 22 GND 21 GND 24 ACLK- 23 BTX3­26 ACLK+ 25 BTX3+ 28 GND 27 GND 30 ATX3- 29 BCLK­32 ATX3+ 31 BCLK+ 34 GND 33 GND 36 DDCPCLK 35 SMBCKL 38 DDCPDATA 37 SMBDATA 40 N/C 39 SPDIFO
Pin Description
1-2 LCDVCC (3.3V) 3-4 LCDVCC (5V) 5-6 LCDVCC (12V)
Default: 1-2
Page 23
HS-774 User’s Manual
-
21-
To setup the LCD, you need the component below:
1. A panel with LVDS interfaces.
2. An inverter for panel’s backlight power.
3. A LCD cable and an inverter cable.
For the cables, please follow the pin assignment of the conn ector t o make a cable, b ecaus e every panel has its own pin assignment, so we do not provide a standard cable; please find a local cable manufacture to make cables.
LCD Installation Guide:
1. Preparing the HS-774, LCD panel and the backlight inverter.
2. Please check the datasheet of the panel to see the voltage of the panel, and set the jumper JVLCD to +12V or +5V or +3.3V.
3. You would need a LVDS type cable.
4. To connect all of the devices well.
For sample illustrator only
Panel side
Board side
Page 24
HS-774 User’s Manual
-
22-
After setup the devices well, you need to select the LCD panel type in the BIOS. The panel type mapping is list below:
BIOS panel type selection form (BIOS Version:1.0)
Single / Dual channel Single / Dual channel
NO. Output format NO. Output format
1 640 x 480 9 1680 x 1050 2 800 x 600 10 1920 x 1200 3 1024 x 768 11 1440 x 900 4 1280 x 1024 12 1600 x 900 5 1400 x 1050 Reduced Blanking 13 800 x 480 6 1400 x 1050 non-Reduced Blanking 14 1280 x 800 7 1680 x 1200 15 1920 x 1080 8 1366 x 768 16 OEM Keep (Ver:1.1)
Page 25
HS-774 User’s Manual
-
23-
CDIN
1
4
2.9 <Integrated Audio Interface>
The board provides the onboard high definition audio with Realtek ALC888.
Connector: CN_AUDIO
Type: 10-pin (2 x 5) header (pitch = 2.54mm)
Pin Description Pin Description
1 MIC_L 2 Ground 3 MIC_R 4 N/C 5 Speaker_R 6 MIC Detect 7 SENSE 8 N/C 9 Speaker_L 10 Speaker Detect
Connector: CDIN
Type: 4-pin header (pitch = 2.54mm)
Pin Description
1 CD – Left 2 Ground 3 Ground 4 CD – Right
4
1
1 2
9 10
CN_AUDIO
1 2
9 10
Page 26
HS-774 User’s Manual
-
24-
2.10 <USB Interface>
HS-774 integrates four USB3.0 ports and two USB2.0 ports.
The specifications of USB3.0 are listed below:
The specifications of USB2.0 are list:
Interface USB3.0
Controller
Intel®QM77
Transfer Rate Up to 5Gb/s
Voltage 5V
Interface USB2.0
Controller
Intel®QM77
Transfer Rate Up to 480Mb/s
Voltage 5V
CN_USB1
Type: USB2.0
2 10
1 9
JVUSB
2 6
2 6
1 10
20 11
CN_USB3- 1/2
Type: USB3.0
Page 27
HS-774 User’s Manual
-
25-
Connector: CN_USB3- 1/2 Type: 20-pin (2 x 10) header (pitch = 2.0mm)
Pin Description Pin Description
1 VCC(5V_SB/ 5V) 20 NC 2 USB3.0_RX0- 19 VCC(5V_SB/ 5V) 3 USB3.0_RX0+ 18 USB3.0_RX1­4 Ground 17 USB3.0_RX1+ 5 USB3.0_TX0- 16 Ground 6 USB3.0_TX0+ 15 USB3.0_TX1­7 Ground 14 USB3.0_TX1+ 8 Data0- 13 Ground 9 Data0+ 12 Data1­10 NC 11 Data1+
Connector: CN_USB1 Type: 10-pin (2 x 5) header (pitch = 2.54mm)
Pin Description Pin Description
1 VCC (5V_SB/ 5V) 2 VCC (5V_SB/ 5V) 3 Data0- 4 Data1­5 Data0+ 6 Data1+ 7 Ground 8 Ground 9 Ground 10 N/C
Connector: JVUSB
Type: 6-pin Power select jumper
Pin Description
1-3 & 2-4 5V_SB 3-5 & 4-6 5V
Default: 1-3 & 2-4
Effective patterns of connection: 1-3 & 2-4 or 3-5 & 4-6
Warning: others cause damages
2 6
1 5
1 5
2 6
Page 28
HS-774 User’s Manual
-
26-
2.11 <Serial Port>
The board supports five RS232 serial port and one jumper selectable RS232/ 422/ 485 serial ports. The jumper JCSEL1 and JCSEL2 can let you configure the communicating modes for COM2.
Connector: COM1/2, 3/4, 5/6 Type: 20-pin (2 x 10) header pitch = 2.54x1.27mm
Pin Description Pin Description
1 DCD1 2 RXD1 3 TXD1 4 DTR1 5 GND1 6 DSR1 7 RTS1 8 CTS1 9 RI1 10 N/C 11 DCD2/422TX-/485- 12 RX2/422TX+/485+ 13 TX2/422RX+ 14 DTR2/422RX­15 Ground 16 DSR2 17 RTS2 18 CTS2 19 RI2 20 N/C
Setting RS-232 & RS-422 & RS-485 for COM2
CN_COM1/2
12
2
10
9 1
2
2 6
1 5
JP1 JP2 JP3
JCSEL1
JCSEL2
JP4
CN_COM3/4 CN_COM5/6
Page 29
HS-774 User’s Manual
-27-
Jumper: JP1/JP2/JP3/JP4 (COM1/2/3/4) Type: onboard 6-pin header
Function JCSEL2 JCSEL1
IrDA
RS-422
RS-485
RS-232
Power Mode JP1/2/3/4
Pin 9 with 5V Power 1-2 Pin 9 with 12V Power 3-4 Standard COM port
5-6
Default setting: 5-6
12
11
2
1
12
11
2
1
Default setting:
JCSEL1: (1-3, 2-4, 7-9, 8-10) JCSEL2: (1-2)
12
11
2
1
12
11
2
1
1 7
2 8
1 7
2 8
1 7
2 8
1 7
2 8
Page 30
HS-774 User’s Manual
-
28-
2.12 <PCIE Mini Card and SIM Interface>
The board provides two PCIE mini card sockets and a SIM socket.
MINI_CARD1 is the first Mini-PCIe slot for long size Mini-PCIe cards. However, if you are trying to use 3G Mini-PCIe card with a SIM card then place your 3G Mini-PCIe card in this slot and put your SIM card into the SIM card socket beneath this MINI_CARD1 support 3G PCIE Mini card with SIM. MINI_CARD1 slot and option support mSATA.
MINI_CARD2 is the second Mini-PCIe slot for long size Mini-PCIe cards. Please be noted that the MPX-SDVOD card must be placed in this slot. The MPX-SDVOD card will not work if it is placed in other slot. Please also be noted that this slot is the only slot for MPX-SDVOX card but a customized BIOS is needed for the MPX-SDVOX card. Please contact Commell for customized BIOS for your MPX-SDVOX card.
Page 31
HS-774 User’s Manual
-
29-
Connector: SIMM Type: 6-pin SIM socket
Pin Description Pin Description
1 SIMVCC 2 SIMRST 3 SIMCLK 4 NC 5 GND 6 SIMVPP 7 SIMDATA
MINI_CARD2 MINI_CARD1
SIMM
Page 32
HS-774 User’s Manual
-
30-
2.12.1 <SIM Setup>
Step1.
SIM card holder is marked by circle. Slide the cap toward OPEN direction.
Step 2.
Make sure that the cap is now at the OPEN position.
Step 3.
Flip the cap up for inserting a SIM card into.
Page 33
HS-774 User’s Manual
-
31-
Step 4.
Insert a SIM card as shown in the photo. Be sure that the corner cut is on top and the golden pads are up.
Step 5.
Now, flip down the cap as shown in the photo.
Step 6.
Press down and slide the cap to the CLOSE position. Be sure that the cap is tightly held with the socket.
Page 34
HS-774 User’s Manual
-
32-
2.13 <GPIO and SMBUS Interface>
The board provides a programmable 8-bit digital I/O interface; you can use this general purpose I/O port for system control like POS or KIOSK.
Connector: CN_DIO Type: 12-pin (6 x 2) header (pitch = 2.0mm)
Pin Description Pin Description
1 Ground 2 Ground 3 GP10 4 GP14 5 GP11 6 GP15 7 GP12 8 GP16 9 GP13 10 GP17 11 5V 12 12V
Connector: CN_SMBUS Type: 5-pin header for SMBUS Ports
Pin Description
1 VCC 2 N/C 3 SMBDATA 4 SMBCLK 5 Ground
CN_SMBUS
5
12
11
2
1
CN_DIO
1
Page 35
HS-774 User’s Manual
-
33-
2.14 <Power Supply and Fan Interface >
The board requires onboard 4-pin DC 5V/12V power required, optional 5VSB for ATX.
2.14.1 <Power Input>
Connector: DC_IN
Type: 4-pin header
Pin Description Pin Description
1 +12V 3 Ground 2 Ground 4 +5V
Connector: CN_PS Type: 3-pin connector
Pin Description
1 +5VSTBY 2 GND 3 PSON
DC_IN
CN_PS
Page 36
HS-774 User’s Manual
-
34-
2.15 <Switch and Indicator>
The JFRNT provid es front control panel of the board, such as power button, reset an d beeper, etc. Please check well before you connecting the cables on the chassis.
Connector: JFRNT Type: onboard 14-pin (2 x 7) 2.54-pitch header
Function Signal PIN Signal Function
HDLED+ 1 2 PWRLED+
IDE LED
HDLED- 3 4 N/C
Reset+ 5 6 PWRLED-
Power
LED
Reset
Reset- 7 8 SPK+
N/C 9 10 N/C
PWRBT+ 11 12 N/C
Power
Button
PWRBT- 13 14 SPK-
Speaker
1 13
JFRNT
2 14
Page 37
HS-774 User’s Manual
-
35-
Chapter 3 <System Setup>
3.1 <Audio Configuration>
The board integrates Intel® QM77 with REALTEK® ALC888 codec. It can support 2-channel sound under system configuration. Please follow the steps below to setup your sound system.
1. Install REALTEK HD Audio driver.
2. Lunch the control panel and Sound Effect Manager.
3. Select Speaker Configuration
Page 38
HS-774 User’s Manual
-36-
3.2 <Display Properties Setting>
Based on Intel QM77 with HD Graphic, the board supports two DACs for display devic e as different resolution and color bit. Please install the Intel Graphic Driver before you starting setup display devices.
1. Click right button on the desktop to lunch display properties
2. Click Advanced button for more specificity setup.
Click Graphics Properties... for advanced setup
Page 39
HS-774 User’s Manual
-37-
3. This setup options can let you define each device settings.
Click Monitor to setup the CRT monitor for Resolution and Refresh Rate
Click Intel® Dual Display
Clone to setup the dual
display mode as same screen
Page 40
HS-774 User’s Manual
-38-
3.3 <SATA configuration>
SATA Mode:
This option can let you select whether the Serial ATA hard drives would work under normal IDE mode or RAID mode. The RAID mode need more than one HDD is applied.
Page 41
HS-774 User’s Manual
-39-
3.4 <SATA RAID Configuration>
The board integrates Intel® QM77 PCH with RAID function for Serial ATA drives, and supports the configurations below: RAID 0 (Stripping): Two hard drives operating as one drive for optimized d ata R/W performance. It needs two unused drives to build this operation. RAID 1 (Mirroring): Copies the data from first drive to second drive for data security, and if one drive fails, the system would access the applications to the workable drive. It needs two unused drives or one used and one unused drive to build this operation. The second drive must be the same or lager size than first one.
RAID 5 (striping with parity)
A RAID 5 array contains three or more hard drives where the data is divided into manageable blocks called strips. Parity is a mathematical method for recreating data that was lost from a single drive, which increases fault-tolerance. The data and parity are striped across all the hard drives in the array. The parity is striped in a rotating sequence to reduce bottlenecks associated with the parity calculations.
RAID 10 (RAID 0+1)
A RAID 10 array uses four hard drives to create a combination of RAID levels 0 and 1. The data is striped across a two-drive array forming the RAID 0 component. Each of the drives in the RAID 0 array is then mirrored by a RAID 1 component. Intel Matrix Storage Technology: This technology would allow you to use RAID 0+1 mode on only two drives (4 drives needed on traditional RAID 0+1). It will create t wo partitions on each hard drive to simulate RAID 0 and RAID 1. It also can let you modify the partition size without re-formatted.
For more information of Intel Matrix Storage Technology, please visit Intel’s website.
If you need to install an operation system on the RAID set, please use the driver disk attached in the package when it informs you to obtain the RAID drivers.
Page 42
HS-774 User’s Manual
-40-
Please press <CTRL+I> to enter the RAID configuration menu. You can setup the RAID under operation system for Microsoft® Windows XP SP1 , please install the Intel® Application Accelerator Ver.4.5 later to support RAID configuration with Intel® Matrix Storage Technology
Page 43
HS-774 User’s Manual
-
41-
Chapter 4 <BIOS Setup>
The motherboard uses the Phoenix BIOS for the system configuration. The Phoenix BIOS in the single board computer is a customized version of the industrial standard BIOS for IBM PC AT-compatible computers. It supports Intel x86 and compatible CPU architecture based processors and computers. The BIOS provides critical low-level support for the system central processing, memory and I/O sub-systems.
The BIOS setup program of the single board computer let the customers modify the basic
configuration setting. The settings are stored in a dedicated battery-backed memory, NVRAM, retains the information when the power is turned off. If the battery runs out of the power, then the settings of BIOS will come back to the default setting.
The BIOS section of the manual is subject to change without notice and is provided her e
for reference purpose only. The settings and configurations of the BIOS are current at the time of print, and therefore they may not be exactly the same as th at displayed on your screen.
To activate CMOS Setup program, press <DEL> key immediately after you turn on the
system. The following message “Press DEL to enter SETUP” should appear in the lower left hand corner of your screen. When you enter the CMOS Setup Utility, the Main Menu will be displayed as Figure 4-1. You can use arrow keys to select your function, press Enter key to accept the selection and enter the sub-menu.
Figure 4-1 CMOS Setup Utility Main Screen
Page 44
HS-774 User’s Manual
-
42-
(This page is left for blank)
Page 45
HS-774 User’s Manual
-
43-
Appendix A <I/O Port Pin Assignment>
A.1 <Serial ATA Port>
Connector: SATA1/2/3/4/5/6 Type: 7-pin wafer connector
1 2 3 4 5 6 7
GND RSATA_TXP1 RSATA_TXN1 GND RSATA_RXN1 RSATA_RXP1 GND
A.2 <IrDA Port>
Connector: CN_IR Type: 5-pin header for SIR Ports
A.3 <VGA Port>
Connector: CRT Type: 15-pin D-sub female connector on bracket
Pin Description Pin Description Pin Description
1 RED 6 Ground 11 N/C 2 GREEN 7 Ground 12 DDCDA 3 BLUE 8 Ground 13 HSYNC 4 N/C 9 N/C 14 VSYNC 5 Ground 10 Ground 15 DDCCLK
A.4 <LAN Port>
Connector: RJ45 Type: RJ45 connector with LED on bracket
Pin Description
1 VCC 2 N/C 3 IRRX 4 Ground 5 IRTX
Pin 1 2 3 4 5 6 7 8
Description MI0+ MI0- MI1+ MI2+ MI2- MI1- MI3+ MI3-
1
6
10
1 2 3 4 5
11 12 13 14 15
5
JCSEL1 must
jump
to “SIR”
7 1
8 1
Page 46
HS-774 User’s Manual
-
44-
A.5 <LAN LED Port>
Connector: JSPD1/2 Type: 5-pin header for LAN Speed LED connector
When Lan speed 10/100Mbps
When Lan speed 1Gbps
Connector: JATC1/2 Type: 5-pin header for LAN Activity LED connector
Pin Description
1 LED­2 LED+
Pin Description
1 LED+ 2 LED-
Pin Description
1 LED­2 LED+
Page 47
HS-774 User’s Manual
-
45-
Appendix B <Flash BIOS>
B.1 <Flash Tool>
The board is based on Phoenix BIOS and can be updated easily by the BIOS auto flash tool. You can download the tool online at the address below:
http://www.phoenix.com/en/home/ http://www.commell.com.tw/Support/Support_SBC.htm
File name of the tool is “Phlash.exe”, it’s the utility that can write the data into the BIOS flash ship and update the BIOS.
B.2 <Flash BIOS Procedure>
1. Please make a bootable floppy disk.
2. Get the last .bin files you want to update and copy it into the disk.
3. Copy Phlash16.exe to the disk.
4. Power on the system and flash the BIOS. (Example: C:/Pflash XXX.bin /bbl /cvar /sa)
5. Restart the system.
Any question about the BIOS re-flash please contact your distributors or visit the web-site at below:
http://www.commell.com.tw/support/support.htm
UT
Page 48
HS-774 User’s Manual
-
46-
Appendix C <Programming GPIO’s >
The GPIO can be programmed with the MSDOS debug program using simple IN/OUT commands. The followin g lines show an example how to do this.
GPIO0…..GPIO7 bit0……bit7
-o 2 E 87 ;enter configuration
-o 2E 87
-o 2E 07
-o 2F 09 ;enable GPIO function
-o 2E 30
-o 2F 02 ;enable GPIO configuration
-o 2E F0
-o 2F xx ;set GPIO as input/output; set ‘1’ for input,’0’for output
-o 2E F1
-o 2F xx ;if set GPIO’s as output, in this register its value can be set
Optional :
-o 2E F2
-o 2F xx ; Data inversion register ; ‘1’ inverts the current value of the bits ,’0’ leaves them as they are
-o 2E 30
-o 2F 01 ; active GPIO’s
For further information, please refer to Winbond W83627DHG-P datasheet.
Page 49
HS-774 User’s Manual
-
47-
Appendix D <Programming Watchdog Timer >
The watchdog timer makes the system auto-reset while it stops to work for a period. The integrated watchdog timer can be setup as system reset mode by program.
Timeout Value Range
- 1 to 255
- Second or Minute
Program Sample
Watchdog timer setup as system reset with 5 second of timeout
2E, 87 2E, 87 2E, 07 2F, 08 Logical Device 8 2E, 30 Activate 2F, 01 2E, F5 Set as Second* 2F, 00 2E, F6 Set as 5 2F, 05
* Minute: bit 3 = 1; Second: bit 3 = 0
You can select Timer setting in the BIOS, after setting the time options, the system will reset according to the period of your selection.
Page 50
HS-774 User’s Manual
-
48-
Contact Information
Any advice or comment about our products and service, or anything we can help you please don’t hesitate to contact with us. We will do our best to support you for your products, projects and business.
Taiwan Commate Computer Inc.
Address
19F., No.94, Sec. 1, Xintai 5th Rd., Xizhi Dist., New Taipei City 22102, Taiwan
TEL +886-2-26963909 FAX +886-2-26963911
Website
TUhttp://www.commell.com.twUT
E-Mail
TUinfo@commell.com.twUT (General Information) TUtech@commell.com.twUT (Technical Support)
Facebook
https://www.facebook.com/pages/Taiwan-Commate-Computer-Inc/547993955271899
Twitter https://twitter.com/Taiwan_Commate
Commell is a brand name of Taiwan commate computer Inc.
Loading...