COMMELL HS-771 User Manual

Page 1
HS-771
Half-size PCI CPU Card
User’s Manual
Edition 1.1
2009/7/15
Page 2
HS-771 User’s Manual
Copyright
Copyright 2009, all rights reserved. This document is copyrighted and all rights are reserved. The information in this document is subject to change without prior notice to make improvements to the products. This document contains proprietary information and pr otected by copyright. No part of this document may be reproduced, copied, or translated in any form or any means without prior written permission of the manufacturer. All trademarks and/or registered trademarks contains in this document are prop erty of their respective owners.
Disclaimer
The company shall not be liable for any incidental or consequential damages resulting from the performance or use of this product. The company does not issue a warranty of any kind, express or implied, including without limitation implied warranties of merchantability or fitness for a particular purpose. The company has the right to revise the manual or include changes in the specifications of the product described within it at any time without notice and without obligation to notify any person of such revision or changes.
Trademark
All trademarks are the property of their respective holders.
Any questions please visit our website at http://www.commell.com.tw
Page 3
HS-771 User’s Manual
Packing List:
Please check the package content before you starting using the board.
Hardware:
HS-771 Half-size PCI CPU Card x 1
Cable Kit:
PS2 Keyboard / Mouse Y-cable x 1
SATA Cable x 2
4-pin to 3-pin ATX cable x 1
DVI VGA Cable x 1
USB Cable x 1
CPU Cooler x 1
YPbPr Cable (Optional) SDTV Cable (Optional)
COM Cable x 1
AUDIO Cable x 1
Printed Matters:
Driver CD x 1 (Including User’s Manual)
Page 4
HS-771 User’s Manual
Index
Chapter 1 <Introduction>..............................................................................................6
1.1 <Product Overview> .........................................................................................6
1.2 <Product Specification>....................................................................................7
1.3 <Mechanical Drawing>.....................................................................................8
1.4 <Block Diagram>..............................................................................................9
Chapter 2 <Hardware Setup>......................................................................................10
2.1 <Connector Location>....................................................................................10
2.2 <Jumper Location & Reference>....................................................................11
2.2.1 <CMOS Setup> .................................................................................12
2.2.2 <JAT Setup>......................................................................................12
2.3 <Connector Reference>.................................................................................13
2.3.1 <Internal Connectors> .......................................................................13
2.3.2 <External Connectors>......................................................................13
2.4 <CPU and Memory Setup>............................................................................14
2.4.1 <CPU Setup>.....................................................................................14
2.4.2 <Memory Setup> ...............................................................................15
2.5 <Serial ATA Interface>....................................................................................16
2.6 <Ethernet Interface>....................................................................................... 17
2.6.1 <LAN Port>........................................................................................17
2.7 <Onboard Display Interface> .........................................................................18
2.7.1 <Analog Display>...............................................................................18
2.7.2 <Digital Display>................................................................................19
2.7.2 <HDTV Interface>.............................................................................. 23
2.8 <Integrated Audio Interface>..........................................................................25
2.9 <GPIO Interface>...........................................................................................26
2.10 <Power Supply>...........................................................................................27
2.10.1 <Power Input> .................................................................................27
2.11 <Switch and Indicator>.................................................................................28
2.12 <Serial Port> ................................................................................................29
Page 5
HS-771 User’s Manual
2.13 <USB Ports>................................................................................................31
2.14 <Keyboard & Mouse Port>...........................................................................32
2.14.1 <PS2 Port>......................................................................................32
2.14.2 <ATKB Port>...................................................................................32
2.15 <PCI Express Mini Card>.............................................................................33
2.16 <Mini PCI Interface> ....................................................................................33
Chapter 3 <System Setup>......................................................................................... 34
3.1 <Audio Configuration> ...................................................................................34
3.2 <Display Properties Setting>..........................................................................35
Chapter 4 <BIOS Setup>............................................................................................. 37
Appendix A <I/O Port Pin Assignment>.....................................................................39
A.1 <SMBUS Port>..............................................................................................39
A.2 <IrDA Port>....................................................................................................39
Appendix B <Flash BIOS>..........................................................................................40
B.1 <Flash Tool>..................................................................................................40
B.2 <Flash BIOS Procedure> ..............................................................................40
Appendix C <System Resources> .............................................................................41
C.1 <Direct memory access (DMA)> ...................................................................41
C.2 <Input/Output (IO)>.......................................................................................41
C.3 <Interrupt request (IRQ)>..............................................................................43
C.4 <Memory>.....................................................................................................44
Appendix D <Programming GPIO’s>......................................................................... 45
Appendix E <Programming Watchdog Timer> ......................................................... 46
Contact Information ....................................................................................................47
Page 6
HS-771 User’s Manual
(This page is left for blank)
Page 7
HS-771 User’s Manual
Chapter 1 <Introduction>
1.1 <Product Overview>
HS-771, the new generation of the Half-size PCI CPU Card, supports Intel Penryn
Processor for 667/800/1066 MHz front side bus and features Intel GM45 and ICH9M chipset, integrated GMA 4500MHD graphics up to 1024MB shared with system memory, DDR3 memory, REALTEK High Definition Audio, Serial ATA and two Intel Gigabit LAN.
Intel Penryn Processor
The board supports Intel Penryn Processors with 667/800/1066 MHz front side bus, 6MB L2 cache, to provide more powerful performance than before.
New features for Intel GM45 chipset
The board integrates Intel GM45 and ICH9M chipset, to provide new generation of the mobile solution, supports Intel GMA 4500MHD graphics up to 1024MB shared with system memory, DDR3 800/1066 MHz memory, built-in high speed mass storage interface of serial ATA, High Definition Audio with 2 channels surrounding sound.
All in One multimedia solution
Based on Intel GM45 and ICH9M chipset, the board provides high performance onboard graphics, 18/24-bit dual channel LVDS interface, DVI, HDTV and 2 channels High Definition Audio, to meet the very requirement of the multimedia application.
Flexible Extension Interface
The board provides one mini-PCI socket and one PCI Express Mini card.
Page 8
HS-771 User’s Manual
1.2 <Product Specification>
General Specification
Form Factor Half-size PCI Bus CPU Card CPU Support Intel Penryn Processor
Package type: Micro-FCPGA478 (Socket-P)
Front side bus: 667/800/1066 MHz Memory 2 x DDRIII SO-DIMM 800/1066 up to 8GB Chipset Intel GM45 & ICH9M Real Time Clock Chipset integrated RTC with onboard lithium battery Watchdog Timer Generates a system reset with internal timer for 1min/s ~255min/s Power Management ACPI 2.0 compliant, supports power saving mode Serial ATA Interface 4 x serial ATAII interface with 300MB/s transfer rate VGA Interface Intel integrated extreme GMA 4500MHD (Graphic Media Accelerator)
Technology Video Memory Up to 1024MB shared with system memory LVDS interface Onboard 18/24-bit dual channel LVDS connector with
+3.3V/+5V/+12V supply Audio Interface Intel integrated ICH9M with Realtek HD Audio codec LAN Interface 2 x Intel 82574L Gigabit Ethernet GPIO interface Onboard programmable 8-bit Digital I/O interface Extended Interface 1 x PCI express Mini card and 1 x Mini PCI socket Internal I/O Port 1 x RS232/422/485, 1 x RS232, 1 x ATKB, 1 x SMBUS, 1 x GPIO, 1 x
HDTV, 8 x USB ports, 1 x IrDA, 1 x LVDS, 4 x Serial ATA, 1 x LCD
inverter, 1 x Front panel Audio, 1 x CDIN and 1 x VGA External I/O Port 2 x RJ45 LAN ports, 1 x DVI-I port and 1 x PS/2 Keyboard/Mouse Port Power Requirement DC 5V/12V power required, optional 5VSB for ATX
Onboard 4-pin power connector & 3-pin ATX connecto Dimension 185mm x 122mm (L x W) Temperature Operating within 0~60 centigrade
Storage within –20~85 centigrade
Ordering Code
HS-771 Onboard VGA, LVDS, DVI-I, LAN, USB2.0, HD Audio, SATA, HDTV,
SMBUS, Mini PCI and PCI Express mini card MPX-574D PCI Express mini card supports single Giga LAN MPX-574D2 PCI Express mini card supports dual Giga LAN ADP-L2T 18bit LVDS to TTL module CBP-5P4 Support 4 X PCI slots backplane
For further product information please visit the website at http://www.commell.com.tw
r
Page 9
HS-771 User’s Manual
1.3 <Mechanical Drawing>
Page 10
HS-771 User’s Manual
A
1.4 <Block Diagram>
Intel Penryn Processor
VGA Interface Intel GMA 4500MHD
1 x LVDS & HDTV & DVI
4 x Serial ATA
W25X80 SPI
8 x USB 2.0
ALC888 HD Audio
1 x RS422/485/232
1 x RS232 & 8-bit GPIO & IrD
GM45
ICH9M
W83627DHG
2 x 204-pin DDR3 SO-DIMM 800/1066 MHz up to 8GB
1 x Mini-PCI
1 x PCI Express mini card
2 x Intel 82574L
1 x SMBUS
9-
-
Page 11
HS-771 User’s Manual
Chapter 2 <Hardware Setup>
2.1 <Connector Location>
MINI_CARD
CN_DIO
CN_SMBUS CN_IR
CN_COM
SATA1/2/3/4
CN_USB2 CN_USB1
SO-DIMMA
DC_IN
SYSFAN
CN_PS
DVI
RJ45_1
RJ45_2
PS2
CD_IN
CN_VGA
CN_AUDIO
CN_ATKB
MINI-PCI
SO-DIMM
CN_LVDS
CN_INV
CN_HDTV
CN_USB4 CN_USB3
CPUFANJFRNT
PCIA
-
10-
Page 12
HS-771 User’s Manual
2.2 <Jumper Location & Reference>
Jumper Function
JRTC CMOS Operating/Clear Setting JAT AT/ATX Mode Setting JVLCD Panel Voltage Setting
JVINV Inverter Voltage Setting JCSEL1 Com2 RS-232/RS-422/RS-485/IR Setting JCSEL2 Com2 RS-232/RS-422/RS-485/IR Setting
JRTC
JCSEL2
JCSEL1
JAT
JVLCD
JVINV
11-
-
Page 13
HS-771 User’s Manual
2.2.1 <CMOS Setup>
The board’s data of CMOS can be setting in BIOS. If the board refuses to boot due to inappropriate CMOS settings, here is how to proceed to clear (reset) the CMOS to its default values.
Jumper: JRTC Type: Onboard 3-pin jumper
1 3
JRTC Mode
1-2 Clear CMOS 2-3 Normal Operation
Default setting: 2-3
JAT
1 3
JRTC
1 3
2.2.2 <JAT Setup>
Jumper: JAT Type: Onboard 3-pin jumper
JRTC Mode
1-2 AT Mode 2-3 ATX Mode
Default setting: 2-3
1 3
12-
-
Page 14
HS-771 User’s Manual
2.3 <Connector Reference>
2.3.1 <Internal Connectors>
Connector Function Remark
CPU Socket478 for socket-P CPU SO-DIMMA/B 204 -pin DDR3 SO-DIMM socket SATA1/2/3/4 7-pin Serial ATA connector DC_IN 4-pin power supply connector CN_AUDIO 5 x 2-pin audio connector CD_IN 4-pin CD-ROM audio input connector CN_DIO 6 x 2-pin digital I/O connector CN_USB1/2/3/4 5 x 2-pin USB connector CPUFAN 4-pin CPU cooler fan connector SYSFAN 3-pin system cooler fan connector CN_HDTV 5 x 2-pin HDTV interface CN_LVDS 20 x 2-pin LVDS connector CN_INV 5-pin LCD inverter connector CN_IR 5-pin IrDA connector CN_SMBUS 5-pin SMBUS connector CN_PS 3-pin ATX function connector CN_INV 5-pin LCD inverter connector CN_ATKB 5-pin AT keyboard connector JFRNT 14-pin front panel switch/indicator
connector Mini-PCI 124-pin Mini-PCI socket Type IIIA PCIE Mini card 52-pin PCIE Mini card CN_COM 20-pin RS232 & RS422/485/232
connector
2.3.2 <External Connectors>
Connector Function Remark
DVI DVI Digital VGA connector RJ45_1/2 RJ45 LAN connector PS/2 PS/2 keyboard and mouse connector
13-
-
Page 15
HS-771 User’s Manual
y
2.4 <CPU and Memory Setup>
2.4.1 <CPU Setup>
The board comes with the socket478 for Intel Penryn socket-P Processor 667/800/1066 MHz of front side bus and 6MB L2 cache. Please follow the instruction to install the CPU properly.
Unlock wa
1. Use the flat-type screw drive to unlock the CPU socket
Checkpoint
2. Follow the pin direction to install the processor on the socket
3. Lock the socket
4. Socket P has 478 pins, but is not pin-compatible with Socket M CPU.
14-
-
Socket-M CPU Check point
Page 16
HS-771 User’s Manual
2.4.2 <Memory Setup>
HS-771 has two 204-pin DDR3 SO-DIMM supports up to 8GB of memory capacity. The
memory frequency supports 800/1066MHz. Only Non-ECC memory is supported. Dual-Channel technology is supported while applying two same modules on one of each group.
SO-DIMMB
SO-DIMMA
15-
-
Page 17
HS-771 User’s Manual
7
2.5 <Serial ATA Interface>
Based on Intel ICH9M, the board provides four Serial ATAII interfaces with up to 300MB/s of transfer rate.
Connector: SATA1/2/3/4
SATA2 SATA4 SATA1 SATA3
Type: 7-pin wafer connector
1 2 3 4 5 6 7
GND SATA_TXP0 SATA_TXN0 GND SATA _RXN0 SATA_RXP0 GND
16-
-
1
Page 18
HS-771 User’s Manual
2.6 <Ethernet Interface>
The board integrates with two Intel PCI Express Gigabit Ethernet controllers, as the PCI Express x1 can speed up to 250MB/s of transfer rate instead of late PCI bus with 133MB/s of transfer rate. The Intel Gigabit Ethernet supports triple speed of 10/100/1000Base-T, with IEEE802.3 compliance and Wake-On-LAN supported.
RJ45_1
RJ45_2
2.6.1 <LAN Port>
Connector: RJ45_1/2 Type: RJ45 connector with LED
Pin 1 2 3 4 5 6 7 8
Description MI0+ MI0- MI1+ MI2+ MI2- MI1- MI3+ MI3-
8
1
17-
-
Page 19
HS-771 User’s Manual
2.7 <Onboard Display Interface>
Based on Intel GM45 chipset with built-in GMA (Graphic Media Accelerator) 4500MHD graphics up to 1024MB shared with system memory, the board provides one DB15 on DVI-I real external DVI VGA cable, one 40-pin LVDS interface with 5-pin LCD backlight inverter connector and one DVI-I on bracket. The board provides dual display function with clone mode and extended desktop mode for VGA, LVDS and HDTV.
2.7.1 <Analog Display>
Please connect your CRT or LCD monitor with DB15 to the DVI VGA cable DB15 female connector on rear I/O port.
DVI-IDVI
DB15 VGA
1516
CN_VGA
12
Connector: CN_VGA Type: onboard 16-pin connector for CN_VGA connector pitch 2.00mm
Pin Signal Pin Signal
1 BR 2 BG 3 BB 4 NC 5 -CRTATCH 6 VGAGND 7 -CRTATCH 8 VGAGND
9 NC 10 VGAGND 11 NC 12 5VCDA 13 5HSYNC 14 5VSYNC 15 5VCLK 16 NC
18-
-
Page 20
HS-771 User’s Manual
2.7.2 <Digital Display>
The board provides DVI external connector and one 40-pin LVDS connector for 18/24-bit dual channel panels, supports up to 1920 x 1200 (UXGA) resolution, with one LCD backlight inverter connector and one jumper for panel voltage setting.
DVI
JVINV
JVLCD
5 6
CN_INV
3
1
5
CN_LVDS
1
2
39
40
Effective patterns of connection: 1-2 / 3-4 / 5-6
2 1
3
4
56
Warning: others cause damages
19-
-
Page 21
HS-771 User’s Manual
Connector: CN_INV Connector: JVLCD Type: 5-pin LVDS Power Header Type: 6-pin Power select Header
Pin Description
1 +12V 2 Reserved (Note) 3 GND 4 GND 5 ENABKL
Note: Reserved for MB internal test
Please treat it as NC.
Connector: JVINV Type: 3-pin LVDS Power Header
Pin Description
1-2 INV_VCC (+12V) 3-4 INV_VCC (5V)
Default: 1-2
Connector: CN_LVDS Type: onboard 40-pin connector for LVDS connector Connector model: HIROSE DF13-40DP-1.25V
Pin Description Pin Description
2 LCDVCC 1 LCDVCC
4 GND 3 GND
6 ATX0- 5 BTX0-
8 ATX0+ 7 BTX0+ 10 GND 9 GND 12 ATX1- 11 BTX1­14 ATX1+ 13 BTX1+ 16 GND 15 GND 18 ATX2- 17 BTX2­20 ATX2+ 19 BTX2+ 22 GND 21 GND 24 ACLK- 23 BTX3­26 ACLK+ 25 BTX3+ 28 GND 27 GND 30 ATX3- 29 BCLK­32 ATX3+ 31 BCLK+ 34 GND 33 GND 36 DDCPCLK 35 N/C 38 DDCPDATA 37 N/C 40 N/C 39 N/C
Pin Description
1-2 LCDVCC (3.3V) 3-4 LCDVCC (5V) 5-6 LCDVCC (12V)
Default: 1-2
20-
-
Page 22
HS-771 User’s Manual
To setup the LCD, you need the component below:
1. A panel with LVDS interfaces.
2. An inverter for panel’s backlight power.
3. A LCD cable and an inverter cable.
For the cables, please follow the pin assignment of the connector to make a c able, becaus e every panel has its own pin assignment, so we do not provide a standard cable; ple ase fin d a local cable manufacture to make cables.
LCD Installation Guide:
1. Preparing the HS-771, LCD panel and the backlight inverter.
2. Please check the datasheet of the panel to see the voltage of the panel, and set the jumper JVLCD to +12V or +5V or +3.3V.
3. You would need a LVDS type cable.
Panel side
For sample illustrator only
4. To connect all of the devices well.
Board side
21-
-
Page 23
HS-771 User’s Manual
After setup the devices well, you need to select the LCD panel type in the BIOS. The panel type mapping is list below:
BIOS panel type selection form (BIOS Version:1.0)
18-bit Single channel 24-bit Dual channel
NO. Output format NO. Output format
1 640 x 480 1 1280 x 768 2 800 x 480 2 1280 x 1024 3 800 x 600 3 1600 x 1200 4 1024 x 768 4 1920 x 1080 5 1280 x 800 5 1920 x 1200
18-bit Dual channel
1 1280 x 768
24-bit Single channel 1 1024 x 768 2 1280 x 768 3 1280 x 800 4 1366 x 768
22-
-
Page 24
HS-771 User’s Manual
2.7.2 <HDTV Interface>
The board provides an HDTV interface with Intel GM45, support PAL and NTSC of TV system, and display (clone or extended desktop) function with VGA, DVI and LVDS.
Connector: CN_HDTV Connector type: 10-pin header HDTV connector pitch 2.54mm (Optional cable)
Pin Number Description Pin Number Description
1 GND 2 DACB_L 3 DACC_L 4 GND 5 GND 6 N/C 7 DACA_L 8 GND 9 N/C 10 N/C
CN_HDTV 2 10
1 9
-
23-
Page 25
HS-771 User’s Manual
YPbPr Cable
(Optional cable)
SDTV Cable
(Optional cable)
-
24-
Page 26
HS-771 User’s Manual
2.8 <Integrated Audio Interface>
The board integrates onboard audio interface with REALTEK ALC888 codec, with Intel next generation of audio standard as High Definition Aud io, it offers more sound and other advantages than former HD audio compliance. The main specifications of ALC888 are:
High-performance DACs with 100dB S/N ratio 2 DAC channels support 16/20/24-bit PCM format for 2 audio solution 16Compatible with HD Meets Microsoft WHQL/WLP 2.0 audio requirements
The board provides 2 channels audio phone jacks and MIC-in port for front I/O panel through audio cable.
CD_IN 1 4
CN_AUDIO
10
2
1
9
Connector: CN_AUDIO Connector: CD_IN
Type: 10-pin (2 x 5) header Type: 4-pin header (pitch = 2.54mm x 1.27mm) (pitch = 2.54mm)
Pin Description Pin Description
1 MIC_L 2 Ground 3 MIC_R 4 Reserve 5 Speaker_R 6 MIC Detect 7 SENSE 8 N/C 9 Speaker_L 10 Speaker Detect
-
25-
Pin Description
1 MIC_L 3 MIC_R 5 Speaker_R 7 SENSE 9 Speaker_L
Page 27
HS-771 User’s Manual
2.9 <GPIO Interface>
The board provides a programmable 8-bit digital I/O interface; you can use this general purpose I/O port for system control like POS or KIOSK.
Connector: CN_DIO Type: 12-pin (6 x 2) header (pitch = 2.0mm)
Pin Description Pin Description
1 Ground 2 Ground 3 GP10 4 GP14 5 GP11 6 GP15 7 GP12 8 GP16 9 GP13 10 GP17 11 VCC 12 +12V
12
2
CN_DIO
11
1
26-
-
Page 28
HS-771 User’s Manual
4
2.10 <Power Supply>
2.10.1 <Power Input>
The board requires onboard 4-pin DC 5V/12V power required, optional 5VSB for ATX.
Connector: DC_IN Type: 4-pin DC power connector
Pin Description
1 +12V 2 Ground 3 Ground 4 +5V
Connector: CN_PS
Type
: 3-pin ATX function connector
Pin Description
1 5VSTBY 2 Ground 3 -PSON
1
DC_IN
1 3
CN_PS
27-
-
Page 29
HS-771 User’s Manual
2.11 <Switch and Indicator>
The JFRNT provides front control panel of the board, such as power button, reset and beeper, etc. Please check well before you connecting the cables on the chassis.
Connector: JFRNT Type: onboard 14-pin (2 x 7) header pitch = 2.54mm
Function Signal PIN Signal Function
IDE LED
Reset
Power
Button
HDLED+ 1 2 PWRLED+
PWRBT- 11 12 N/C
PWRBT+ 13 14 SPK-
HDLED- 3 4 N/C
Power
LED
Reset+ 5 6 PWRLED-
Reset- 7 8 SPK+
N/C 9 10 N/C
Speaker
28-
-
JFRNT
2
1
14
13
Page 30
HS-771 User’s Manual
2.12 <Serial Port>
The board supports one RS232 serial port and one jumper selectable RS232/ 422/485 serial ports. The jumper JCSEL1 and JCSEL2 can let you configure the communicating modes for COM2.
Connector: CN_COM Type: 20-pin (2 x 10) header pitch = 2.54x1.27mm
Pin Description Pin Description
1 DCD1 2 RXD1 3 TXD1 4 DTR1 5 Ground 6 DSR1 7 RTS1 8 CTS1 9 RI1 10 N/C 11 DCD2/422TX-/485- 12 RX2/422TX+/485+ 13 TX2/422RX+ 14 DTR2/422RX­15 Ground 16 DSR2 17 RTS2 18 CTS2 19 RI2 20 N/C
COM2
2
COM1
COM Cable
1
20
CN_COM
19
29-
-
Page 31
HS-771 User’s Manual
Setting RS-232/RS-422/RS-485/IrDA:
2
1
JCSEL2
12
11
278
1
JCSEL1
Function JCSEL1 JCSEL2
82
2
12
IrDA
1
7
2
8
1
2
11 12
RS-422
1
7
1
11
12
11
12
RS-485
2
8
1
2
7
8
2
1
2
RS-232
1
7
1
Default: RS-232
30-
-
11
Page 32
HS-771 User’s Manual
2.13 <USB Ports>
Based on ICH9M, the board provides eight USB2.0 ports with provides up to 480Mbps of transferring rate.
Interface USB2.0
Controller ICH9M
Transfer Rate Up to 480Mb/s
Output Current 500mA
Connector: CN_USB1/2/3/4 Type: 10-pin 5 x 2 header for dual USB Ports pitch = 2.54mm
Pin Description Pin Description
1 VCC 2 VCC 3 Data0- 4 Data1­5 Data0+ 6 Data1+ 7 Ground 8 Ground 9 Ground 10 N/C
PS: The USB2.0 will be only active when you connecting with the USB2.0 devices, if you
CN_USB2 CN_USB1
CN_USB4 CN_USB3
2
10
1
9
insert an USB1.1 device, the port will be changed to USB1.1 protocol automatically. The transferring rate of USB2.0 as 480Mbps is depending on device capacity, exact transferring rate may not be up to 480Mbps.
31-
-
Page 33
HS-771 User’s Manual
2.14 <Keyboard & Mouse Port>
2.14.1 <PS2 Port>
The PS/2 connector supports standard PS/2 keyboard directly or both PS/2 keyboard and mouse through for PS/2 Y-cable.
Connector: PS2 Type: 6-pin Mini-DIN connector on bracket
Pin 1 2 3 4 5 6
Description KBCLK MSCLK Ground VCC KBDATA MSDATA
2.14.2 <ATKB Port>
Connector: CN_ATKB Type: 5-pin box header
Pin 1 2 3 4 5
Description VCC Ground N/C KBDATA KBCLK
3
1
5 6
2
4
15
Female
PS2
1 5
CN_ATKB
Mouse
Keyboard
32-
-
Page 34
HS-771 User’s Manual
2.15 <PCI Express Mini Card>
The PCI Express Mini Cards are 30 x 56 mm. There is a 52 pin edge connector.
Connector: MINI_CARD
Type: 52-pin
edge connector
51
52
2
1
2.16 <Mini PCI Interface>
The system connector for Type III consists of a 124-pin card edge type connector.
Connector: MINI-PCI
Type: 124-pin Type III
edge connector
2
1
MINI-PCI
124 123
33-
-
Page 35
HS-771 User’s Manual
Chapter 3 <System Setup>
3.1 <Audio Configuration>
The board integrates Intel® ICH9M with REALTEK® ALC888 codec. It can support 2-channel sound under system configuration. Please follow the steps below to setup your sound system.
1. Install REALTEK HD Audio driver.
2. Lunch the control panel and Sound Effect Manager.
3. Select Speaker Configuration
34-
-
Page 36
HS-771 User’s Manual
3.2 <Display Properties Setting>
Based on Intel GM45 GMCH with GMA 4500MHD (Graphic Media Accelerator) up to
1024MB shared with system memory
different resolution and color bit. Please install the Intel Graphic Driver before you starting setup display devices.
1. Click right button on the desktop to lunch display properties
2. Click Advanced button for more specificity setup.
, the board supports two DACs for display device as
35-
-
Click Graphics Properties... for advanced setup
Page 37
HS-771 User’s Manual
3. This setup options can let you define each device settings.
Select Intel(R) Dual Display
Clone for Colors, Resolution
and Refresh Rate
Select Dual Display Clone to setup the dual display mode as same screen
Select Extended Desktop for Colors, Resolution and Refresh Rate
Select Extended Desktop to setup the dual display mode as same screen
36-
-
Page 38
HS-771 User’s Manual
Chapter 4 <BIOS Setup>
The motherboard uses the Award BIOS for the system configuration. The Award BIOS in the single board computer is a customized version of the industrial standard BIOS for IBM PC AT-compatible computers. It supports Intel x86 and compatible CPU architecture based processors and computers. The BIOS provides critical low-level support for the system central processing, memory and I/O sub-systems.
The BIOS setup program of the single board computer let the customers modify the basic configuration setting. The settings are stored in a dedicated battery-backed memory, NVRAM, retains the information when the power is turned off. If the battery runs out of the power, then the settings of BIOS will come back to the default setting.
The BIOS section of the manual is subject to change without notice and is provided h ere
for reference purpose only. The settings and configurations of the BIOS are current at the time of print, and therefore they may not be exactly the same as that displayed on your screen.
To activate CMOS Setup program, press <DEL> key immediately after you turn on the
system. The following message “Press DEL to enter SETUP” should appear in the lower left hand corner of your screen. When you enter the CMOS Setup Utility, the Main Menu will be displayed as Figure 4-1. You can use arrow keys to select your function, press Enter key to accept the selection and enter the sub-menu.
Figure 4-1 CMOS Setup Utility Main Screen
37-
-
Page 39
HS-771 User’s Manual
(This page is left for blank)
-
38-
Page 40
HS-771 User’s Manual
Appendix A <I/O Port Pin Assignment>
A.1 <SMBUS Port>
Connector: CN_SMBUS Type: 5-pin header for SMBUS Port
Pin Description
1 VCC 2 N/C 3 SMBDATA 4 SMBCLK 5 Ground
A.2 <IrDA Port>
Connector: CN_IR Type: 5-pin header for SIR Ports
Pin Description
1 VCC 2 N/C 3 IRRX 4 Ground 5 IRTX
JCSEL1 must jump to “SIR
1
1
5
5
CN_SMBUS CN_IR
1 5
39-
-
Page 41
HS-771 User’s Manual
Appendix B <Flash BIOS>
B.1 <Flash Tool>
The board is based on Award BIOS and can be updated easily by the BIOS auto flash tool. You can download the tool online at the address below:
http://www.phoenix.com/en/home/ http://www.commell.com.tw/Support/Support_SBC.htm
File name of the tool is “awdflash.exe”, it’s the utility that can write the data into the BIOS flash ship and update the BIOS.
B.2 <Flash BIOS Procedure>
1. Please make a bootable floppy disk.
2. Get the last .bin files you want to update and copy it into the disk.
3. Copy XXX.bin and awdflash.exe to the disk.
4. Power on the system and flash the BIOS. (Example: C:/ awdflash XXX.bin)
5. Restart the system.
Any question about the BIOS re-flash please contact your distributors or visit the web-site at below:
http://www.commell.com.tw/support/support.htm
40-
-
Page 42
HS-771 User’s Manual
Appendix C <System Resources>
C.1 <Direct memory access (DMA)>
C.2 <Input/Output (IO)>
41-
-
Page 43
HS-771 User’s Manual
42-
-
Page 44
HS-771 User’s Manual
C.3 <Interrupt request (IRQ)>
43-
-
Page 45
HS-771 User’s Manual
C.4 <Memory>
44-
-
Page 46
HS-771 User’s Manual
Appendix D <Programming GPIO’s>
The GPIO’can be programmed with the MSDOS debug program using simple IN/OUT commands. The following lines show an example how to do this.
GPIO0…..GPIO7 bit0……bit7
-o 2 E 87 ;Enter configuration
-o 2E 87
-o 2E 07
-o 2F 09 ;Enable GPIO function
-o 2E 30
-o 2F 02 ;Enable GPIO configuration
-o 2E F0
-o 2F xx ;Set GPIO as input/output; set ‘1’ for input,’0’for output
-o 2E F1
-o 2F xx ;If set GPIO’s as output, in this register its value can be set
Optional:
-o 2E F2
-o 2F xx ; Data inversion register; ‘1’ inverts the current value of the bits,’0’ leaves them as they are
-o 2E 30
-o 2F 01 ; active GPIO’s
For further information, please refer to Winbond W83627DHG datasheet.
45-
-
Page 47
HS-771 User’s Manual
Appendix E <Programming Watchdog Timer>
The watchdog timer makes the system auto-reset while it stops to work for a period. The integrated watchdog timer can be setup as system reset mode by program.
Timeout Value Range
- 1 to 255
- Second or Minute
Program Sample
Watchdog timer setup as system reset with 5 second of timeout
2E, 87 2E, 87 Entry Key 2E, 07 2F, 08 Logical Device 8 2E, 30 2F, 01 Activate 2E, F5 2F, 00 Set as Second* 2E, F6 2F, 05 Set as 5
* Minute: bit 3 = 0; Second: bit 3 = 1
You can select Timer setting in the BIOS, after setting the time options, the system will reset according to the period of your selection.
46-
-
Page 48
HS-771 User’s Manual
Contact Information
Any advice or comment about our products and service, or anything we can help you please don’t hesitate to contact with us. We will do our best to support you for your products, project a business.
Taiwan Commate Computer Inc.
Address
TEL +886-2-26963909 FAX +886-2-26963911 Website http://www.commell.com.tw E-Mail info@commell.com.tw
Commell is a brand name of Taiwan Commate Computer Inc.
19F No. 94, Sec. 1, Shin Tai Wu Rd., Shi Chih Taipei Hsien, Taiwan
(General Information)
tech@commell.com.tw
(Technical Support)
47-
-
Loading...