COMMELL HS-770E User Manual

Page 1
HS-770(E) Serial
Half-Size PCI CPU Card
User’s Manual
Edition 1.1
2009/02/03
Page 2
Copyright
Copyright 2005, all rights reserved. This document is copyrighted and all rights are reserved. The information in this document is subject to change without prior notice to make improvements to the products. This document contains proprietary information and pr otected by copyright. No part of this document may be reproduced, copied, or translated in any form or any means without prior written permission of the manufacturer. All trademarks and/or registered trademarks contains in this document are prop erty of their respective owners.
Disclaimer
The company shall not be liable for any incidental or consequential damages resulting from the performance or use of this product. The company does not issue a warranty of any kind, express or implied, including without limitation implied warranties of merchantability or fitness for a particular purpose. The company has the right to revise the manual or include changes in the specifications of the product described within it at any time without notice and without obligation to notify any person of such revision or changes.
Trademark
All trademarks are the property of their respective holders.
Any questions please visit our website at TUhttp://www.commell.com.twUT
2
Page 3
HS-770(E) User’s Manual
)
Packing List:
Please check the package content before you starting using the board.
Hardware:
HS-770(E) motherboard x 1
Cable Kit:
44-pin
44-pin
ATA33 IDE Cable x1
SATA Cable x 2
DVI-I Y cable x 1
40-pin
Floppy Cable x 1
PS/2 Keybroad & Mouse cable x 1
CPU Cooler x 1
YPbPr Cable x 1 (Only HS-770)SDTV Cable x 1 (Only HS-770)
COM port Cable x 2
Dual USB cable x 1
Audio cable x 1
Printed Matters:
Driver CD x 1 (Including User’s Manual
Parallel cable x 1
3
Page 4
HS-770(E) User’s Manual Index
Index
Chapter 1 <Introduction>...............................................................7
1.1 <Product Overview>............................................................................7
1.2 <Product Specification>......................................................................8
1.3 <Mechanical Drawing>......................................................................10
1.4 <Block Diagram>...............................................................................12
Chapter 2 <Hardware Setup>....................................................14
2.1 <Connector Location>.......................................................................14
2.2 <Jumper Location & Reference> ......................................................16
2.3 <Connector Reference>....................................................................17
2.3.1 <Internal Connectors> .........................................................17
2.3.2 <External Connectors> ........................................................17
2.4 <CPU and Memory Setup>...............................................................18
2.4.1 <CPU Setup>.....................................................................18
2.4.2 <Memory Setup>................................................................19
2.5 <CMOS Setup>.................................................................................20
2.6 <Enhanced IDE Interface>................................................................21
2.7 <Serial ATA Interface>.......................................................................21
2.8 <Floppy Port>....................................................................................22
2.9 <Ethernet Interface> .........................................................................23
2.10 <Onboard Display Interface>..........................................................24
2.10.1 <Digital Visual Interface Display>........................................24
2.10.2 <Digital Display>..............................................................25
2.10.3 <HDTV Interface> HS-770(E) not supports TV out function. ....29
2.11 <Integrated Audio Interface>...........................................................30
2.12 <GPIO Interface>............................................................................32
2.13 <Power Supply>..............................................................................33
2.13.1 <Power Input>..................................................................33
2.14 <Switch and Indicator>....................................................................34
4
Page 5
HS-770(E) User’s Manual Index
Chapter 3 <System Setup>.........................................................35
3.1 <Video Memory Setup>....................................................................35
Chapter 4 <BIOS Setup>..............................................................37
Appendix A <I/O Port Pin Assignment>............................ 39
A.1 <IDE Port>........................................................................................39
A.2 <Serial ATA Port>..............................................................................40
A.3 <Floppy Port>...................................................................................40
A.4 <IrDA Port>.......................................................................................41
A.5 <Serial Port>.....................................................................................42
A.6 <VGA Port>.......................................................................................43
A.7 <LAN Port>.......................................................................................43
A.8 < USB Interface >.............................................................................43
Appendix B <Flash BIOS>...........................................................44
B.1 <Flash Tool>.....................................................................................44
B.2 <Flash BIOS Procedure> .................................................................44
Contact Information.........................................................................46
5
Page 6
HS-770(E) User’s Manual
(This Page is Left for Blank)
6
Page 7
HS-770(E) User’s Manual Introduction
Chapter 1 <Introduction>
1.1 <Product Overview>
HS-770(E) is the new generation of the Half-size PCI CPU card, with supporting last
Intel Pentium M processors for 533MHz front side bus, Intel 915GM(E) and ICH6-M chipset, integrated GMA900 graphics, DDR2 memory, REALTEK AC97 Audio, Serial ATA, mini PCI and dual Gigabit LAN.
New Intel Pentium M Processor
The board supports last Intel Pentium M processors with 533MHz front side bus, 2MB L2 cache, to provide more powerful performance than before.
New features for Intel 915GM(E) chipset
The board integrates Intel 915GM(E) and ICH6-M chipset, to provide new generation of the mobile solution, supports Intel GMA900 graphics, DDR2 400/533 memory, built-in high speed mass storage interface of serial ATA,
Multimedia solution
Based on Intel 915GM(E) and ICH6-M chipset, the board provides two high performance onboard graphics, 24-bit dual channel LVDS interface, HDTV to meet the very requirement of the multimedia application.
Flexible Extension Interface
The board provides one Compact Flash Type II slot and one mini-PCI slot.
7
Page 8
HS-770(E) User’s Manual Product Specification
1.2 <Product Specification>
General Specification
Form Factor Half-size PCI CPU card CPU Intel® Pentium M / Celeron M processors
Package type: FC-PGA478 L2 Cache: 512KB/1MB/2MB Front side bus: 400/533MHz
( The Intel® Celeron® M Processor 4xx series have been designed to work with the Mobile Intel® 945 Express Chipset Family only .)
Memory 2 x 240-pin DDR2 400/533MHz SDRAM up to 2GB
Up to 8GB/s of bandwidth with dual-channel interleaved mode Dual-Channel technology supported
Unbufferred, none-ECC memory supported only Chipset Intel® 915GM(E) (Northbridge) and ICH6-M (Southbridge) BIOS Phoenix-Award v6.00PG 4Mb PnP flash BIOS Green Function Power saving mode includes doze, standby and suspend modes.
ACPI version 1.0 and APM version 1.2 compliant Watchdog Timer System reset programmable watchdog timer with 1 ~ 255 sec./min. of
timeout value Real Time Clock Intel® ICH6-M built-in RTC with lithium battery Enhanced IDE UltraDMA33/66/100 IDE interface supports up to 2 ATAPI devices
One 44-pin IDE port onboard
One Compact Flash Type II socket on solder side Serial ATA Intel® ICH6-M integrates 2 Serial ATA interfaces
Up to 150MB/s of transfer rate
Multi-I/O Port
Chipset Intel® ICH6-M with Winbond® W83627THF controller Serial Port 3 internal RS-232 serial ports one internal RS-232/422/485 serial ports USB Port Four Hi-Speed USB 2.0 ports with 480Mbps of transfer rate Parallel Port One internal Floppy Port One standard type Floppy port IrDA Port One IrDA compliant Infrared interface supports SIR K/B & Mouse External PS/2 keyboard and mouse ports on near LAN port GPIO One 12-pin Digital I/O connector with 8-bit programmable I/O interface Smart Fan One CPU fan connectors for fan speed controllable
VGA Display Interface
Chipset Intel® 915GM(E) GMCH (Graphic Memory Controller Hub) Frame Buffer Up to 128MB shared with system memory Display Type CRT, LCD monitor with digital display
Onboard 24-bit dual channel LVDS interface
Onboard HDTV interface
8
Page 9
HS-770(E) User’s Manual Product Specification
Connector External DVI female connector on near LAN port
Onboard 40-pin LVDS connector
Onboard 8-pin TV-out connector
Ethernet Interface
Controller Marvell 88E8053 PCI Express Gigabit Ethernet controller Type Triple speed 10/100/1000Base-T
auto-switching Fast Ethernet
Full duplex, IEEE802.3U compliant
Connector Dual External RJ45 connectors with LED on rear I/O panel
Audio Interface
Chipset Intel® ICH6M with Realtek® ALC201A codec Interface 2 channels Connector Onboard Audio connector for Line-out, Line-in, MIC-in
Expansive Interface
CF One Compact Flash Type II socket on solder Side PCI One Mini-PCI socket for TYPE III (32-bit, 33MHz)
Power supply: +3.3V, +5V
Power and Environment
Power Requirement Dimension 185mm (L) x 121 (H) mm Temperature Operating within 0 ~ 60P
Onboard 4-pin connector
DC 5V/12V
Storage within -20 ~ 85P
o
P
C (32 ~ 140P
o
P
C (-4 ~ 185P
o
P
F)
o
P
F)
Ordering Code
HS-770(E)DXG2 Intel Pentium M Mini-ITX motherboard with onboard VGA, Dual Gigabit
LAN, SATA,4 x USB 2.0 Ports, Audio, 4 x RS232 serial port, LVDS,
HDTV, Mini-PCI
The specifications may be different as the actual production. For further product information please visit the website at TUhttp://www.commell.com.tw
UT
9
Page 10
HS-770(E) User’s Manual Mechanical Drawing
1.3 <Mechanical Drawing>
10
Page 11
HS-770(E) User’s Manual
(This Page is Left for Blank)
11
Page 12
HS-770(E) User’s Manual Block Diagram
1.4 <Block Diagram>
Intel Pentium M/Celeron M Processors
Intel GMA900 Graphics
LVDS
2 x 240-pin DDR2
DVI
HDTV
SDVO
915GM(E)
400/533MHz up to 2GB
CompactFlash
UltraDMA33/66/100 IDE
4 x USB2.0 ports
ALC201A
2 x Serial ports
2 x Serial ports
1 x Floppy ports
ICH6-M
BIOS
1 x Parallel Port
2 x Serial ATA ports
PCIE
PICMG
Marvell E8053
Gigabit LAN
Mini-PCI slot
12
8-bit GPIO
IrDA
Page 13
HS-770(E) User’s Manual
(This Page is Left for Blank)
13
Page 14
HS-770(E) User’s Manual Hardware Setup
_VGA
_
Chapter 2 <Hardware Setup>
2.1 <Connector Location>
CN_USB1/2 COM12 COM34 CN_ LPT CN IR CN_DIO SYSFAN
JCSEL1 JCSEL2
AUDIO
CN
CN
CN_ATKB JCFSEL SATA JVLCD2 CN_INV CN_TV CPUFAN
IDE
Floppy
CN_PWR
14
CN_LVDS2 JFRNT CN_PS
Page 15
HS-770(E) User’s Manual Hardware Setup
CF
15
Page 16
HS-770(E) User’s Manual Jumper Location & Reference
2.2 <Jumper Location & Reference>
Jumper Function
JRTC CMOS Operating/Clear Setting JCFSEL CF with IDE mode selection JVLCD2 Panel Voltage Setting JCSEL1 Choose RS232/485/422 JCSEL2 Choose RS232/485/422
JRTC
16
JCFSEL
JVLCD2
JCSEL1
JCSEL2
RS232 RS485 RS422
Page 17
HS-770(E) User’s Manual Connector Reference
2.3 <Connector Reference>
2.3.1 <Internal Connectors>
Connector Function Remark
CPU Socket479 for CPU Standard DDRIIA/B 240 -pin DDR2 SDRAM DIMM socket Standard IDE 44-pin IDE connector Silm FDD 34-pin slim type floppy connector Standard SATA1/2 7-pin Serial ATA connector Standard CN_AUDIO 5 x 2-pin audio connector Standard CN_DIO 6 x 2-pin digital I/O connector Standard CN_USB1/2 5 x 2-pin USB connector Standard CPUFAN 4-pin CPU cooler fan connector Standard SYSFAN 3-pin system cooler fan connector Standard CN_LVDS2 20 x 2-pin LVDS connector Standard CN_INV 5-pin LCD inverter connector Standard CN_IR 5-pin IrDA connector Standard CN_COM12/34 10 x 2-pin COM1/2/3/4 connector Standard JFRNT 14-pin front panel switch/indicator connector Standard CN_TV 4 x 2-pin TV-out connector Standard MINIPCI Mini-PCI socket Standard CF CompactFlash Type II socket Standard
2.3.2 <External Connectors>
Connector Function Remark
DVI DVI Digital VGA connector Standard RJ45_A/B RJ45 Lan port connector Standard KB/MS PS/2 keyboard/Mouse connector Standard
17
Page 18
HS-770(E) User’s Manual CPU and Memory Setup
y
2.4 <CPU and Memory Setup>
2.4.1 <CPU Setup>
The board comes with the socket479 for Intel Pentium M/Celeron M processors, it supports new generation of Intel Pentium M processors with 533MHz of front side bus and 2MB L2 cache. Please follow the instruction to install the CPU properly.
Check point
Unlock wa
1. Use the flat-type screw drive to unlock the CPU socket
2. Follow the pin direction to install the processor on the socket
3. Lock the socket
18
Page 19
HS-770(E) User’s Manual Memory Setup
2.4.2 <Memory Setup>
The board provides two 240-pin DDR2 DIMMs to support DDR2 400/533 memory modules up to 2GB of capacity. Non-ECC, unbuffered memory is supported only. While applying two same modules, dual channel technology is enabled automatically for higher performance.
DDRIIB/A
Please check the pin number to match the socket side well before installing memory module.
19
Page 20
HS-770(E) User’s Manual CMOS Setup
3
2.5 <CMOS Setup>
The board’s data of CMOS can be setting in BIOS. If the board refuses to boot due to inappropriate CMOS settings, here is how to proceed to clear (reset) the CMOS to its default values.
Jumper: JRTC Type: Onboard 3-pin jumper
JRTC Mode
1-2 Clear CMOS 2-3 Normal Operation
Default setting
JRTC
1
20
Page 21
HS-770(E) User’s Manual Enhanced IDE Interface
2.6 <Enhanced IDE Interface>
The board has one UltraDMA33 IDE interface to support up to 2 A TAPI devices, and one CompactFlash Type II socket on the solder side, with jumper JCFSEL for IDE master/slave mode selection.
Jumper: JCFSEL Type: onboard 3-pin header
JCFSEL Mode
1-2 Master 2-3 Slave
Default setting
1 3
JCFSEL
2.7 <Serial ATA Interface>
Based on Intel ICH6-M, the board provides two Serial ATA interfaces with up to 150MB/s of transfer rate.
SATA1 SATA2
21
Page 22
HS-770(E) User’s Manual Floppy Port
2
2.8 <Floppy Port>
The board provides one standard type floppy port.
FDD
34
1
33
22
Page 23
HS-770(E) User’s Manual Ethernet Interface
2.9 <Ethernet Interface>
The board integrates with two Marvell 88E8053 PCI Express Gigabit Ethernet controllers, as the PCI Express 1x can speed up to 250MB/s of transfer rate instead of late PCI bus with 133MB/s of transfer rate. The Marvell 88E8053 supports triple speed of 10/100/100Base-T, with IEEE802.3 compliance and Wake-On-LAN supported.
RJ45 LAN connector
23
Page 24
HS-770(E) User’s Manual Onboard Display Interface
2.10 <Onboard Display Interface>
Based on Intel 915GM(E) chipset with built-in GMA (Graphic Media Accelerator) 900 graphics, the board provides one DVI connector on real external I/O port, and one 40-pin LVDS interface with 5-pin LCD backlight inverter connector. The board provides dual display function with clone mode and extended d esktop mode for CRT,DVI,LCD and TV
2.10.1 <Digital Visual Interface Display >
Please connect your CRT or LCD monitor with DVI male connector to the onboard female connector on rear I/O port.
24
DVI
Page 25
HS-770(E) User’s Manual Digital Display
5
2.10.2 <Digital Display>
The board provides one 40-pin LVDS connector for 24-bit single/dual channel panels, supports up to 1600 x 1200 (UXGA) and 1920 x 1200 (WUXGA) of resolution, with one LCD backlight inverter connector and one jumper for panel voltage setting.
JVLCD2
1
2
CN_LVDS2
1
31
CN_INV
39
40
25
Page 26
HS-770(E) User’s Manual Digital Display
Connector: CN_INV Connector: JVLCD2 Type: 5-pin LVDS Power Header Type: 3-pin Power select Header
Pin Description Pin Description
1 +12V 1 VCC 2 GND 2 LCDVCC 3 GND 3 VCC3 4 GND 5 ENABKL
Connector: CN_LVDS2 Type: onboard 40-pin connector for LVDS connector Connector model: HIROSE DF13-40DP-1.25V
Pin Signal Pin Signal
2 LCDVCC 1 LCDVCC 4 GND 3 GND 6 ATX0- 5 BTX0-
8 ATX0+ 7 BTX0+ 10 GND 9 GND 12 ATX1- 11 BTX1­14 ATX1+ 13 BTX1+ 16 GND 15 GND 18 ATX2- 17 BTX2­20 ATX2+ 19 BTX2+ 22 GND 21 GND 24 ACLK- 23 N/C 26 ACLK+ 25 N/C 28 GND 27 GND 30 N/C 29 BCLK­32 N/C 31 BCLK+ 34 GND 33 GND 36 LVDDCLK 35 N/C 38 LVDDDAT 37 N/C 40 N/C 39 N/C
26
Page 27
HS-770(E) User’s Manual Digital Display
To setup the LCD, you need the component below:
1. A panel with LVDS interfaces.
2. An inverter for panel’s backlight power.
3. A LCD cable and an inverter cable.
For the cables, please follow the pin assignment of the connector to make a c able, becaus e every panel has its own pin assignment, so we do not provide a standard cable; ple ase fin d a local cable manufacture to make cables.
LCD Installation Guide:
1. Preparing the HS-770(E), LCD panel and the backlight inverter.
2. Please check the datasheet of the panel to see the voltage of the panel, and set the jumper JVLCD2 to +5V or +3.3V.
3. You would need a LVDS type cable.
Panel side
For sample illustrator only
4. To connect all of the devices well.
Board side
27
Page 28
HS-770(E) User’s Manual Digital Display
After setup the devices well, you need to select the LCD panel type in the BIOS.
The panel type mapping is list below:
HS-770(E) BIOS LCD Type selection form
Single channel 18bit (VER:1.0S18A) Dual channel 18bit (VER:1.0D18A)
NO. Output format NO. Output format
1 640 x 480 1 2 800 x 600 2 3 1024 x 768 3 4 1280 x 768 4
Single channel 24bit (VER:1.0S24A) Dual channel 24bit (VER:1.0D24A)
NO. Output format NO. Output format
1 1024 x 768 1 1024 x 768 2 1280 x 768 2 1280 x 1024 3 1280 x 1024 3 1400 x 1050 4 1366 x 768 4 1600 x 1200
28
Page 29
HS-770(E) User’s Manual HDTV Interface
2.10.3 <HDTV Interface> HS-770(E) not supports TV out function.
The board provides output types with Composite, S-Video and Component (YPbPr) Composite and S-Video up to 1024 x 768 for NTSC/PAL Component support 480p/720p/1080i/1080p mode
Connector: CN_TV Connector type: 8-pin header TV-out connector (pitch = 2.54mm) Pin
Pin Number Assignment Pin Number Assignment
1 GND 2 S-Video/Y 3 S-video/Pr 4 GND 5 GND 6 GND 7 Composite/Pb 8 GND
Notice1: This connector is for both S-Video/Composite and YPbPr outputs; please use attached two cables in the package for SDTV or HDTV devices. Notice2: S-Video and Composite can not be used at the same time.
8
CN_TV
1
29
Page 30
HS-770(E) User’s Manual Integrated Audio Interface
2.11 <Integrated Audio Interface>
HS-770(E) provides a stereo audio interface with Realtek ALC201A AC97 Codec. The
CN_AUDIO provides the interface to use attached audio cable.
30
CN_AUDIO
1
2
9
10
Page 31
HS-770(E) User’s Manual Integrated Audio Interface
Connector: CN_AUDIO
Type: 10-pin (2 x 5) 2.54-pitch header
Pin Description Pin Description
1 Line – Right 2 Ground 3 Line – Left 4 MIC 5 MIC 6 Ground 7 N/C 8 Line Out – Left 9 Line Out – Right 10 Ground
Connector: CDIN Type: 4-pin header (pitch = 2.54mm)
Pin Description
1 CD – Left 2 Ground 3 Ground 4 CD – Right
31
Page 32
HS-770(E) User’s Manual GPIO Interface
2.12 <GPIO Interface>
The board provides a programmable 8-bit digital I/O interface; you can use this general purpose I/O port for system control like POS or KIOSK.
Connector: CN_DIO Type: 12-pin (6 x 2) 2.0mm x 2.0mm-pitch header
Pin Description Pin Description
1 Ground 2 Ground 3 GP10 4 GP14 5 GP11 6 GP15 7 GP12 8 GP16 9 GP13 10 GP17 11 VCC 12 +12V
32
12
CN_DIO
1
Page 33
HS-770(E) User’s Manual Power supply
2.13 <Power Supply>
2.13.1 <Power Input>
The board requires DC 12V/5V input with onboard 4-pin connector, for the input current, please take a reference of the power consumption report on appendix.
Connector: CN_PWR Type: 4-pin standard power connector
Pin Description Pin Description
1 +12V 2 Ground 3 Ground 4 +5V
Connector: CN_PS Type: 3-pin ATX function connector
Pin Description Pin Description Pin Description 1 5V Standby 2 Ground 3 Power On
1
CN_PWR
1 3
4
33
Page 34
HS-770(E) User’s Manual Switch and Indicator
2.14 <Switch and Indicator>
The JFRNT provides front control panel of the board, such as power button, reset and beeper, etc. Please check well before you connecting the cables on the chassis.
Connector: JFRNT Type: onboard 14-pin (2 x 7) 2.54-pitch header
Function Signal PIN Signal Function
IDE LED
Reset
Power Button
VCC 1 2 VCC
Power
Active 3 4 N/C
LED
Reset 5 6 GND
GND 7 8 VCC
N/C 9 10 N/C
Speaker
PWRBT 11 12 N/C
5VSB 13 14 SPKIN
34
JFRNT
2
1
14
13
Page 35
HS-770(E) User’s Manual System Setup
Chapter 3 <System Setup>
3.1 <Video Memory Setup>
Based on Intel® 915GM(E) chipset with GMA (Graphic Media Accelerator) 900, the board supports Intel® DVMT (Dynamic Video Memory Technology) 3.0, which would allow the video memory to be allocated up to 128MB. To support DVMT, you need to install the Intel GMA 900 Driver with supported OS.
BIOS Setup:
On-Chip Video Memory Size: This option combines three items below for setup. On-Chip Frame Buffer Size:
This item can let you select video memory which been allocated for leg acy VGA and SVGA graphics support and compatibility. The available option is 1MB and 8MB.
Fixed Memory Size:
This item can let you select a static amount of page-locked graphics memory which will be allocated during driver initialization. Once you select the memory amount, it will be no longer available for system memory.
DVMT Memory Size:
This item can let you select a maximum size of dynamic amount usage of video memory, the system would configure the video memory depends on your application, this item is strongly recommend to be selected as MAX DVMT.
35
Page 36
HS-770(E) User’s Manual System Setup Fixed + DVMT Memory Size:
You can select the fixed amount and the DVMT amount at the same time for a guaranteed video memory and additional dynamic video memory, please check the table below for available setting.
128MB~255MB
256MB~511MB
512MB upper
Notice:
System Memory
On-Chip
Frame
Buffer Size
1MB 32MB 0MB 32MB 1MB 0MB 32MB 32MB 8MB 32MB 0MB 32MB 8MB 0 32MB 32MB 1MB 64MB 0MB 64MB 1MB 0 64MB 64MB 1MB 128MB 0MB 128MB 1MB 0 128MB 128MB 1MB 64MB 64MB 128MB 8MB 64MB 0MB 64MB 8MB 0 64MB 64MB 8MB 128MB 0MB 128MB 8MB 0 128MB 128MB 8MB 64MB 64MB 128MB 1MB 64MB 0 64MB 1MB 0 64MB 64MB 1MB 128MB 0 128MB 1MB 0 128MB 128MB 1MB 64MB 64MB 128MB 8MB 64MB 0 64MB 8MB 0 64MB 64MB 8MB 128MB 0 128MB 8MB 0 128MB 128MB 8MB 64MB 64MB 128MB
Fixed
Memory
Size
DVMT
Memory
Size
Total Graphic Memory
1. The On-Chip Frame Buffer Size would be included in the Fixed Memory. Please select the memory size according to this table.
36
Page 37
HS-770(E) User’s Manual BIOS Setup
Chapter 4 <BIOS Setup>
The motherboard uses the Award BIOS for the system configuration. The Award BIOS in the single board computer is a customized version of the industrial standard BIOS for IBM PC AT-compatible computers. It supports Intel x86 and compatible CPU architecture based processors and computers. The BIOS provides critical low-level support for the system central processing, memory and I/O sub-systems.
The BIOS setup program of the single board computer let the customers modify the basic configuration setting. The settings are stored in a dedicated battery-backed memory, NVRAM, retains the information when the power is turned off. If the battery runs out of the power, then the settings of BIOS will come back to the default setting.
The BIOS section of the manual is subject to change without notice and is provided here for reference purpose only. The settings and configurations of the BIOS are current at the time of print, and therefore they may not be exactl y the same as that displayed on your screen.
To activate CMOS Setup program, press <DEL> key immediatel y after you turn on the system. The following message “Press DEL to enter SETUP” should appear in the lower left hand corner of your screen. When you enter the CMOS Setup Utility, the Main Menu will be displayed as Figure 4-1. You can use arrow keys to select your function, press Enter key to accept the selection and enter the sub-menu.
Figure 4-1 CMOS Setup Utility Main Screen
37
Page 38
HS-770(E) User’s Manual
(This Page is Left for Blank)
38
Page 39
HS-770(E) User’s Manual I/O Port Pin Assignment
Appendix A <I/O Port Pin Assignment>
A.1 <IDE Port>
Connector: IDE
Type: 44-pin (22 x 2) box header
Pin Description Pin Description
1 Reset 2 Ground 3 D7 4 D8 5 D6 6 D9 7 D5 8 D10 9 D4 10 D11 11 D3 12 D12 13 D2 14 D13 15 D1 16 D14 17 D0 18 D15 19 Ground 20 N/C 21 REQ 22 Ground 23 -IOW 24 Ground 25 -IOR 26 Ground 27 IORDY 28 Ground 29 DACK 30 Ground 31 IDEIRQ 32 IDE32 33 A1 34 P66DET 35 A0 36 A2 37 -CS1 38 -CS3 39 -HD LED1 40 Ground 41 +5V 42 +5V 43 Ground 44 Ground
2
1
44
43
39
Page 40
HS-770(E) User’s Manual SATA & Floppy Port
A.2 <Serial ATA Port>
Connector: SATA1/2 Type: 7-pin wafer connector
1 2 3 4 5 6 7
GND RSATA_TXP1 RSATA_TXN1 GND RSATA_RXN1 RSATA_RXP1 GND
A.3 <Floppy Port>
234FDD
Connector: FDD Type: 34-pin connector
Pin Description Pin Description
1 GND 2 FD DRVDEN 3 GND 4 N/C 5 GND 6 N/C 7 GND 8 FD INDEX 9 GND 10 FD MOA­11 GND 12 N/C 13 GND 14 FD DSA­15 GND 16 N/C 17 GND 18 FD DIR­19 GND 20 FD STEP­21 GND 22 FD WD­23 GND 24 FD WE­25 GND 26 FD TRAK-
27 GND 28 FD WP­ 29 GND 30 FD RDATA­ 31 GND 32 FD HEAD­ 33 GND 34 FD DSKCHG-
33
40
Page 41
HS-770(E) User’s Manual IrDA Port
A.4 <IrDA Port>
Connector: CN_IR Type: 5-pin header for SIR Ports
Pin Description
1 VCC 2 N/C 3 IRRX 4 Ground 5 IRTX
1
5
41
Page 42
HS-770(E) User’s Manual Serial Port
A.5 <Serial Port>
Connector: CN_COM12/CN_COM34 Type: 20-pin (10 x 2) 1.27mm x 2.54mm-pitch header
Pin Description Pin Description
1 DCD 2 RXD 3 TXD 4 DTR 5 GND 6 DSR 7 RTS 8 CTS 9 RI 10 N/C 11 DCD 12 RXD 13 TXD 14 DTR 15 GND 16 DSR 17 RTS 18 CTS 19 RI 20 N/C
2
20
42
1
19
Page 43
HS-770(E) User’s Manual VGA Port
A.6 <VGA Port>
Connector: DVI Type: DVI-I female connector on bracket
Pin Description Pin Description Pin Description
1 TDC2- 11 VGAGND 21 N/C 2 TDC2+ 12 N/C 22 VGAGND 3 VGAGND 13 N/C 23 TLC+ 4 N/C 14 VCC 24 TLC­5 N/C 15 VGAGND C1 VGA R 6 VGACLK 16 THPDET C2 VGA G 7 VGADAT 17 TDC0- C3 VGA B 8 VGA VS 18 TDC0+ C4 VGA HS 9 TDC1- 19 VGAGND C5 VGAGND 10 TDC1+ 20 N/C C6 VGAGND
A.7 <LAN Port>
Connector: RJ45A/B Type: RJ45 connector with LED on bracket
Pin 1 2 3 4 5
Description TRD0+ TRD0- TRD1+ TRD1- NC
Pin 6 7 8 9 10
Description NC TRD2+ TRD2- TRD3+ TRD3-
A.8 < USB Interface >
Connector: CN_USB1/2 Type: 10-pin (5 x 2) header for dual USB Ports
Pin Description Pin Description
1 VCC 2 VCC 3 Data0- 4 Data1­5 Data0+ 6 Data1+ 7 Ground 8 Ground 9 N/C 10 N/C
9
10
1
2
43
Page 44
HS-770(E) User’s Manual Flash BIOS
Appendix B <Flash BIOS>
B.1 <Flash Tool>
The board is based on Award BIOS and can be updated easily by the BIOS auto flash tool. You can download the tool online at the address below:
http://www.phoenix.com/en/home/ http://www.commell.com.tw/Support/Support_SBC.htm
File name of the tool is “awdflash.exe”, it’s the utility that can write the data into the BIOS flash ship and update the BIOS.
B.2 <Flash BIOS Procedure>
1. Please make a bootable floppy disk.
2. Get the last .bin files you want to update and copy it into the disk.
3. Copy awardflash.exe to the disk.
4. Power on the system and flash the BIOS. (Example: C:/ awardflash XXX.bin)
5. Restart the system.
Any question about the BIOS re-flash please contact your distributors or visit the web-site at below:
http://www.commell.com.tw/support/support.htm
UT
44
Page 45
HS-770(E) User’s Manual GPIO Programming
The GPIO’can be programmed with the MSDOS debug program using simple IN/OUT commands.The following lines show an example how to do this.
GPIO0…..GPIO7 bit0……bit7
-o 4E 87 ;enter configuration
-o 4E 87
-o 4E 29
-o 4E 40 ;enale GPIO function
-o 4E 07
-o 4E 07 ;enable GPIO configuration
-o 4E F0
-o 4F xx ;set GPIO as input/output; set ‘1’ for input,’0’for output
-o 4E F1
-o4F xx ;if set GPIO’s as output,in this register its value can be set
Optional :
-o 4E F2
-o 4F xx ; Data inversion register ; ‘1’ inverts the current valus of the bits ,’0’ leaves them as they are
-o 4E 30
-o 4F 01 ; active GPIO’s
For further information, please refer to Winbond W83627THF datasheet.
Notice : All GPIO pin pull-high external resist ance requirement
45
Page 46
HS-770(E) User’s Manual Contact Information
Contact Information
Any advice or comment about our products and service, or anything we can help you please don’t hesitate to contact with us. We will do our best to support you for your products, projects a Business.
Taiwan Commate Computer Inc.
Address
TEL +886-2-26963909 FAX +886-2-26963911 Website E-Mail
19F, No. 94, Sec. 1, Shin Tai Wu Rd., Shi Chih Taipei Hsien, Taiwan
TUhttp://www.commell.com.twUT TUinfo@commell.com.twUT (General Information)
TUtech@commell.com.twUT (Technical Support)
Commell is our trademark of industrial PC division
46
Loading...