COMMELL HE-772 User Manual

Page 1
HE-772
Half-size PCI Bus CPU Card
User’s Manual
Edition 1.0
2011/11/18
Page 2
Page 3
Copyright
Copyright 2010. All rights reserved. This document is copyrighted and all rights are reserved. The information in this document is subject to change without prior notice to make improvements to the products. This document contains proprietary information and pr otected by copyright. No part of this document may be reproduced, copied, or translated in any form or any means without prior written permission of the manufacturer. All trademarks and/or registered trademarks contains in this document are propert y of their respective owners.
Disclaimer
The company shall not be liable for any incidental or consequential damages resulting from the performance or use of this product. The company does not issue a warranty of any kind, express or implied, including without limitation implied warranties of merchantability or fitness for a particular purpose. The company has the right to revise the manual or include changes in the specifications of the product described within it at any time without notice and without obligation to notify any person of such revision or changes.
Trademark
All trademarks are the property of their respective holders.
Any questions please visit our website at TUhttp://www.commell.com.twUT
-1-
Page 4
(
)
Packing List:
Please check the package content before you starting using the board.
Hardware:
HE-772 “Half-size PCI Bus CPU Card” x 1
Cable Kit:
USB Cable x 1
OALUSBA-3
Audio Cable x 1
(OALPJ-HDU
)
Printed Matters:
Driver CD x 1 (Including User’s Manual)
-2-
Dual COM PORT cable x 1
(OALES-BKU2)
Page 5
Index
Chapter 1 <Introduction>................................................................................. 5
1.1 <Product Overview>.................................................................................. 5
1.2 <Product Specification>.............................................................................6
1.3 <Mechanical Drawing>..............................................................................8
1.4 <Block Diagram>.......................................................................................9
Chapter 2 <Hardware Setup>.........................................................................10
2.1 <Connector Location>.............................................................................10
2.2 <Jumper Reference>............................................................................... 12
2.3 <Connector Reference>..........................................................................13
2.3.1 <Internal Connector>..............................................................13
2.3.2 <External Connector> ............................................................13
2.4 <CPU and Memory Setup> .....................................................................14
2.5 <CMOS & ATX Setup>............................................................................15
2.6 < Enhanced IDE & CF Interface >...........................................................16
2.7 <Serial ATA Interface>............................................................................17
2.8 <LAN Interface> ......................................................................................18
2.9 <Onboard Display Interface> ..................................................................19
2.9.1 <Analog VGA Interface> ........................................................19
2.9.2 <Digital Display>.....................................................................20
2.10 <Onboard Audio Interface>...................................................................24
2.11 <USB2.0 Interface>...............................................................................25
2.12 <GPIO and SMBUS Interface> .............................................................26
2.13 <Serial Port Jumper Setting > ...............................................................27
2.14 <Power & FAN Connector >..................................................................30
2.14.1 <Power Input>......................................................................30
2.14.2 <Power Input>......................................................................31
2.14.3 <Fan Connector> .................................................................32
2.15 <Indicator and Switch>..........................................................................33
Chapter 3 <System Configuration>...............................................................34
-3-
Page 6
3.1 <Audio Configuration>.............................................................................34
3.2 <Video Memory Setup>...........................................................................35
3.3 <Display Properties Setting>...................................................................37
Chapter 4 <BIOS Setup> ................................................................................40
Appendix A <I/O Port Pin Assignment> .......................................................41
A.1 < LPT Port >............................................................................................41
A.2 < CRT Port >...........................................................................................41
A.3 < LAN Port >............................................................................................42
A.4 < IrDA Port >............................................................................................42
A.5 < SMBUS Port >......................................................................................42
A.6 < DIO Port >............................................................................................43
A.7 < IDE Port >.............................................................................................43
A.8 < Serial ATA Port >..................................................................................44
A.9 < PS2 Port >............................................................................................44
A.10 < ATKB Port >........................................................................................44
Appendix B <Flash BIOS>..............................................................................45
B.1 BIOS Auto Flash Tool..............................................................................45
B.2 Flash Method...........................................................................................45
Appendix C <System Resources> ................................................................46
C.1 <Direct memory access(DMA)> (HE-772A)............................................46
C.2<Input/output(IO)> (HE-772A)..................................................................46
C.3<Interrupt reguest(IRQ)> (HE-772A)........................................................47
C.4<Memory> (HE-772A)..............................................................................48
Appendix E <Watch Dog timer Setting >......................................................50
Contact Information........................................................................................51
-4-
Page 7
Chapter 1 <Introduction>
1.1 <Product Overview>
HE-772G/H/A is the Half-size PCI Bus CPU Card, with Intel® Atom N450/D410/D510 processor, integrated GMA3150 graphics, Intel® ICH8M, DDR2 SO-DIMM memory, Realtek HD Audio , CF , SATAII , LVDS , LPT , IrDA , DIO, CN_USB , PS2 , SMBUS, CN_INV , CN_CRT , IDE , CN_ATKB , MINI-CARD and Intel® 82583V Gigabit LAN.
Intel® Atom Processor
The Intel® Atom N450/D410/ D510 processor supports one channel of 667 MHz DDR2 SDRAM up to 2GB/4GB/4GB. The chipset features power-efficient graphics with an integrated 18-bit 3D graphics engine based on Intel® Graphics Media Accelerator 3150 architecture with LVDS, CRT display ports. The DMI is designed into the Pineview-M(D) processor to provide an efficient high-bandwidth communication channel between the processor and the ICH8M.
Embedded Intel® ICH8M
The board integrates Intel® ICH8M. It provides I/O capabilities and flexibility via high-bandwidth interfaces such as PCIE and Hi-Speed USB 2.0 connectivity. Serial ATA . HD Audio , Mini-card , CF , LAN , HD Audio . IDE , CN_USB
Flexible Extension Interface
The board also provides Compact Flash Type II socket and 2 x Mini-card socket.
-5-
Page 8
1.2 <Product Specification>
General Specification
Form Factor Half-size PCI Bus CPU Card CPU Intel® Atom N450 Processor 1.66GHz (HE-772G)
Intel® Atom N455 Processor 1.66GHz (HE-7729) Intel® Atom D410 Processor 1.66GHz (HE-772H) Intel® Atom D510 Processor 1.66GHz (HE-772A) Intel® Atom D525 Processor 1.80GHz (HE-772C) Package type: FCBGA559
Memory 1 x 200-pin DDR2 SO-DIMM 667MHz SDRAM up to
2GB/4GB/4GB
(HE-772G / HE-7729 / HE-772H / HE-772A / HE-772C)
Unbufferred, none-ECC memory supported only Chipset Intel® ICH8M BIOS Phoenix-Award v6.00PG 8Mb SPI flash BIOS Green Function Power saving mode includes doze, standby and suspend modes.
ACPI version 2.0 and APM version 1.2 compliant Watchdog Timer System reset programmable watchdog timer with 1 ~ 255 sec./min.
of timeout value Real Time Clock Intel® ICH8-M built-in RTC with lithium battery Enhanced IDE
Serial ATAII Intel® ICH8M integrates 3 Serial ATAII interfaces
Multi-I/O Port
Chipset Intel® ICH8M with Winbond® W83627DHG-P controller Serial Port Five RS-232 and one RS232/422/485 serial ports USB Port Eight Hi-Speed USB 2.0 ports with 480Mbps of transfer rate IrDA Port One IrDA compliant Infrared interface supports SIR K/B & Mouse External PS/2 keyboard and mouse ports on rear I/O panel GPIO One 12-pin Digital I/O connector with 8-bit programmable I/O I
Smart Fan One CPU fan connectors for fan speed controllable Audio Port Realtek ALC888 HD Codec
VGA Display Interface
Chipset Intel® Atom N450 processor (System Controller Hub) (HE-772G)
Frame Buffer Up to 384MB shared with system memory
IDE supports 44-Pin Disk On Module with +5V power supply
One CompactFlash Type II socket on solder side
(No RAID Function)
Up to 300MB/s of transfer rate
nterface
Intel® Atom N455 processor (System Controller Hub) (HE-7729)
Intel® Atom D410 processor (System Controller Hub) (HE-772H)
Intel® Atom D510 processor (System Controller Hub) (HE-772A)
Intel® Atom D525 processor (System Controller Hub) (HE-772C)
-6-
Page 9
Display Type CRT, LVDS monitor with analog display Connector External DB15 female connector on rear I/O panel
Onboard 20-Pin LVDS and 5-Pin inverter connector
Ethernet Interface
Controller 2 x Intel® 82583V Gigabit Ethernet controller Type Triple speed 10/100/1000Base-T
Auto-switching Fast Ethernet Full duplex, IEEE802.3U compliant
Connector Two External RJ45 connectors with LED on rear I/O panel
Expansive Interface
PCIE mini card Two PCIE mini card socket
Power supply: +1.5V, 3VSB
Power and Environment
Power Requirement
Dimension 185 (L) x 122 (H) mm Temperature Operating within 0 ~ 60P
DC 5V/12V power required, optional 5VSB for ATX Onboard 4-pin power connector & 3-pin ATX connector
Storage within –20 ~ 85
O
p
C (32 ~ 140P
O
p
P
C (-4 ~ 185P
O
p
F)
O
p
F)
Ordering Code
HE-772G
Support Intel® Atom N450 processor with onboard VGA, LVDS for 18-bits, Audio, Giga LAN, USB2.0, SATAII, PCIE mini card, PCI, Mini-PCI, Serial Port, CF, SMBUS, GPIO, IrDA, LPT, CDIN, SPDIF
HE-7729 Support Intel® Atom N455 processor with onboard VGA, LVDS for
18-bits, Audio, Giga LAN, USB2.0, SATAII, PCIE mini card, PCI, Mini-PCI, Serial Port, CF, SMBUS, GPIO, IrDA, LPT, CDIN, SPDIF
HE-772H
Support Intel® Atom D410 processor with onboard VGA, LVDS for 18-bits, Audio, Giga LAN, USB2.0, SATAII, PCIE mini card, PCI, Mini-PCI, Serial Port, CF, SMBUS, GPIO, IrDA, LPT, CDIN, SPDIF
HE-772A Support Intel® Atom D510 processor with onboard VGA, LVDS for
18-bits, Audio, Giga LAN, USB2.0, SATAII, PCIE mini card, PCI, Mini-PCI, Serial Port, CF, SMBUS, GPIO, IrDA, LPT, CDIN, SPDIF
HE-772C Support Intel® Atom D525 pro c essor with onboard VGA, LVDS for
18-bits, Audio, Giga LAN, USB2.0, SATAII, PCIE mini card, PCI,
Mini-PCI, Serial Port, CF, SMBUS, GPIO, IrDA, LPT, CDIN, SPDIF CBP-5P4 Support 4 X PCI slots backplane MPX-954E PCI Express mini card support 2 x RS232 , 2 x RS422/RS485.
The specifications may be different as the actual production. For further product information please visit the website at
TUhttp://www.commell.com.twUT
-7-
Page 10
1.3 <Mechanical Drawing>
Unit: inch
8-
-
Page 11
1.4 <Block Diagram>
VGA Interface Intel GMA 3150
CRT
18bit Single Channel LVDS
Intel® Atom
DDR2 SODIMM 667 MHz up to 2G/4G/4G
N450/D410/
D510
1 x IDE
3 x Serial ATA II
6 x USB2.0
W83627DHG-P
RS232/422/485 LPT , IrDA , Dio , SYSFAN , CPUFAN
ICH8M
2 x PCIE mini card
1 x Compact Flash
ALC888 HD Audio
2 x Giga LAN
ICHF81216D
COM 1/2/3/4/5/6
9-
-
Page 12
Chapter 2 <Hardware Setup>
2.1 <Connector Location>
COM3/4/5/6
CN_LPT
CN_INVCN_IR CN_AUDIO
COM1/2 DC_IN
CPUFAN
IDE
CN_LVDS CF
CN_ATKB
CN_CRT
MINICARD CN_USB
SA TA
10-
-
CN_SMBUS
DDRII
CN_DIO
SYSFAN
CN_PS
JFRNT
Page 13
HE-772G/9/H/A/C
CRT RJ45 1/2 PS2
11-
-
Page 14
2.2 <Jumper Reference>
Jumper Function
JRTC CMOS Operating/Clear Setting JVLCD Panel Voltage Setting JAT Power mode select JCSEL1 JCSEL2 JP1 JP2
CN_COM2 RS-232 RS422 RS485 Setting / CN_IR IrDA Setting CN_COM3/4/5/6 RS-232
JCSEL1
JCSEL2
JRTC
JAT
JVLCD
JP1/2
12-
-
Page 15
2.3 <Connector Reference>
2.3.1 <Internal Connector>
Connector Function Remark
DDRII 200 –pin DDR2 SO-DIMM SDRAM
slot SATA1/2/3 7-pin Serial ATA connector CF Compact Flash Type II socket IDE 44-pin primary IDE connector MINI_CARD 2 x 52-pin PCI Express mini card CN_LVDS 10 x 2-pin LVDS connector CN_INV 5-pin LCD inverter connector CN_USB1/2/3 5 x 2-pin USB connector CN_AUDIO 5 x 2-pin audio connector CN_COM1/2/3/4/5/6 10 x 2-pin com connector JFRNT 10-pin switch/indicator connector SYSFAN 3-pin system cooler fan connector CPUFAN 4-pin CPU cooler fan connector DC_IN DC 5V/12V input connector CN_LPT 13 x 2-pin printer connector CN_DIO 6 x 2-pin digital I/O connector CN_IR 5-pin IrDA connector JCSEL1 JCSEL2 JRTC CMOS Operating/Clear Setting CN_CRT 5 x 2-pin CRT connector CN_SMBUS 5-pin SMBUS connector JAT Power mode select JRTC CMOS Operating/Clear Setting
CN_COM2 RS-232 RS422 RS485
Setting / CN_IR IrDA Setting
2.3.2 <External Connector>
Connector Function Remark
CRT DB15 VGA connector PS2 PS2 keyboard and mouse connector RJ45 RJ45 LAN connector
13-
-
Page 16
2.4 <CPU and Memory Setup>
Non-ECC, unbuffered memory is supported only. HE-772G provides one 200-pin DDR2 SO-DIMM to support DDR2 667 memory modules support up to 2GB of capacity.
Suggestion:
DDR2 SO-DIMM Modules:Raw Card A = 2 Ranks of x16 SDRAMs (Double-sided) Raw Card C = 1 Rank of x16 SDRAMs (Single-sided)
HE-772H/ A provides one 200-pin DDR2 SO-DIMM to support DDR2 667 memory modules support up to 4GB of capacity.
Suggestion:
DDR2 SO-DIMM Modules:Raw Card C = 1 Rank of x16 SDRAMs (Single -sided) Raw Card D = 1 Rank of x8 SDRAMs (Single-sided) Raw Card E = 2 Ranks of x8 SDRAMs (Double -sided)
14-
-
DDRII
Page 17
2.5 <CMOS & ATX Setup>
The board’s data of CMOS can be setting in BIOS. If the board refuses to boot due to inappropriate CMOS settings, here is how to proceed to clear (reset) the CMOS to its default values.
Jumper: JRTC Type: Onboard 3-pin jumper
JRTC Mode
1-2 Clear CMOS 2-3 Normal Operation
Default setting
Jumper: JAT Type: onboard 3-pin jumper
JAT Mode
1-2 AT Mode 2-3 ATX Mode
Default setting
JRTC JAT
15-
-
Page 18
2.6 < Enhanced IDE & CF Interface >
The board supports one enhanced IDE interface for 2 ATAPI devices with ATA33. Based on embedded application, the board has one 44-pin IDE connector +5V supported for disk on module. The board also provides a Compact Flash Type II socket.
CF IDE
16-
-
Page 19
2.7 <Serial ATA Interface>
Based on Intel ICH8M, the board provides one Serial ATAII interfaces with up to 300MB/s of transfer rate.
SATA 1/2/3
17-
-
Page 20
2.8 <LAN Interface>
The Intel® 82583v supports triple speed of 10/100/1000Base-T, with IEEE802.3 compliance.
`
LAN
18-
-
Page 21
2.9 <Onboard Display Interface>
Based on Intel® Atom N450/D410/D510 with built-in GMA (Graphic Media Accelerator) 3150 graphics, the board provides one DB15 on real external I/O port, and one 20-pin LVDS interface with 5-pin LCD backlight inverter connector. The board provid es dual display function with clone mode and extended desktop mode for CRT and LVDS.
2.9.1 <Analog VGA Interface>
Please connect your CRT or LVDS monitor with DB15 male connector to the onboard DB15 female connector on rear I/O port. HE-772G /9 supports 1400 x 1050 (WUXGA) resolution displays. HE-772H/ A/C supports 2048 x 1536 (WUXGA) resolution displays.
CRT
19-
-
Page 22
2.9.2 <Digital Display>
The board provides one 20-pin LVDS connector for 18 bit single channel panels, HE-772G/9 supports 1280 x 800 (WUXGA) resolution displays. HE-772H/A/C supports 1366 x 768 (WUXGA) resolution displays, with one LCD backlight inverter connector and one jumper for panel voltage setting
1
1
2
LVDS
1920
20-
-
JVLCD
3
CN_INV
Page 23
Connector: CN_INV Jumper: JVLCD Type: 5-pin Inverter power connector Type: 3-pin Power select jumper Connector model: molex_53261-5pin
Pin Description Pin Description
1 +12V 1-2 +5V 2 GND 2-3 +3.3V
3 GND Default: 2-3 4 GND 5 ENABKL
Connector: CN_LVDS Type: onboard 20-pin connector for LVDS connector Connector model: HIROSE DF13-20DP-1.25V
Pin Signal Pin Signal
2 LCDVCC 1 LCDVCC 4 GND 3 GND 6 TXL0P 5 TXL0N
8 TXL1N 7 GND 10 GND 9 TXL1P 12 TXL2P 11 TXL2N 14 TXLCKN 13 GND 16 GND 15 TXLCKP 18 NC 17 NC 20 GND 19 GND
21-
-
Page 24
To setup the LCD, you need the component below:
1. A panel with LVDS interfaces.
2. An inverter for panel’s backlight power.
3. A LCD cable and an inverter cable.
For the cables, please follow the pin assignment of the connector to make a c able, becaus e every panel has its own pin assignment, so we do not provide a standard cable; ple ase fin d a local cable manufacture to make cables.
LCD Installation Guide:
1. Preparing the HE-772, LCD panel and the backlight inverter
2. Please check the datasheet of the panel to see the voltage of the panel, and set the jumper JVLCD to +5V or +3.3V.
3. You would need a LVDS type cable.
Panel side
For sample illustrator only
4. To connect all of the devices well.
22-
-
Board side
Page 25
After setup the devices well, you need to select the LCD panel type in the BIOS.
The panel type mapping is list below:
HE-772 BIOS panel type selection form
On board Single channel LVDS
18bit
NO. Output format
1 640 x 480 2 800 x 480 3 800 x 600 4 1024 x 600 5 1024 x 768 6 1280 x 768
23-
-
Page 26
2.10 <Onboard Audio Interface>
T he board provides the onboard high definition audio with Realtek ALC888
Connector: CN_AUDIO
Type: 10-pin (2 x 5) 1.27mm x 2.54mm-pitch header
Pin Description Pin Description
1 MIC2_L 2 AGND 3 MIC2_R 4 AVCC 5 FRO_R 6 MIC2_JD 7 F_IO_SEN 8 N/C 9 FRO_L 10 LINE2_JD
CN_AUDIO
24-
-
Page 27
2.11 <USB2.0 Interface>
Connector: CN_USB Type: 10-pin (5 x 2) header for USB Port
Pin Description Pin Description
1 VCC 2 VCC 3 Data0- 4 Data1­5 Data0+ 6 Data1+ 7 Ground 8 Ground 9 Ground 10 N/C
PS: The USB2.0 will be only active when you connecting with the USB2.0 devices, if you insert an USB1.1 device, the port will be changed to USB1.1 protocol automatically. The transferring rate of USB2.0 as 480Mbps is depends on device capacity, exact transferring rate may not be up to 480Mbps.
CN_USB 1/2/3
25-
-
Page 28
2.12 <GPIO and SMBUS Interface>
The board provides a programmable 8-bit digital I/O interface, and a SMBUS (System management bus) interface for control panel application.
Connector: CN_DIO Type: onboard 2 x 6-pin header, pitch=2.0mm
Pin Description Pin Description
1 Ground 2 Ground 3 GP10 4 GP14 5 GP11 6 GP15 7 GP12 8 GP16 9 GP13 10 GP17 11 VCC 12 +12V
Connector: CN_SMBUS Type: 5-pin header for SMBUS Ports
Pin Description
1 VCC 2 N/C 3 SMBDATA 4 SMBCLK 5 Ground
26-
-
CN_DIO CN_SMBUS
Page 29
2.13 <Serial Port Jumper Setting >
The board provides two RS232 serial ports, with jumper selectable RS422/485/IrDA for COM2.
Connector: CN_COM 1/2
Type: 20-pin D-sub male connector
Pin Description Pin Description
1 MDCD1- 11 DCDBTXC­2 MSIN1- 12 SINBTXC 3 MSO1- 13 SOUTBRXC 4 MDTR1- 14 DTRBRXC­5 Ground 15 Ground 6 MDSR1- 16 MDSR2­7 MRTS1- 17 MRTS2­8 MCTS1- 18 MCTS2­9 MRI1- 19 MRI2­10 NC 20 NC
Connector: CN_COM3/4
Type: 20-pin (10 x 2) 1.27mm x 2.54mm-pitch header for COM3/4
Pin Description Pin Description
1 HS_DCD1- 11 HS DCD2­2 HS_RXD1 12 HS RXD2 3 HS_TXD1 13 HS TXD2 4 HS_DTR1- 14 HS DTR2­5 Ground 15 Ground 6 HS_DSR1- 16 HS DSR2­7 HS_RTS1- 17 HS RTS2­8 HS_CTS1- 18 HS DSR2­9 COM39 19 COM49 10 NC 20 NC
27-
-
Page 30
Connector: CN_COM5/6
Type: 20-pin (10 x 2) 1.27mm x 2.54mm-pitch header for COM5/6
Pin Description Pin Description
1 HS_DCD3- 11 HS DCD4­2 HS_RXD3 12 HS RXD4 3 HS_TXD3 13 HS TXD4 4 HS_DTR4- 14 HS DTR4­5 Ground 15 Ground 6 HS_DSR3- 16 HS DSR4­7 HS_RTS3- 17 HS RTS4­8 HS_CTS3- 18 HS DSR4­9 HS RI3- 19 HS RI4­10 NC 20 NC
Jumper: JCSEL1,JCSEL2 Type: 12-pin (6 x 2) & 8-pin (4 x 2) for set COM2 mode jumper
Default: RS232
Function JCSEL2 JCSEL1
IrDA
RS-422
RS-485
RS-232
28-
-
Page 31
Jumper: JP1 (COM 4)/ JP2(COM3) Type: onboard 3 x 2-pin header
JP1/JP2 Mode
5-6 Standard COM Port 3-4 Pin9 with 12V signal 1-2 Pin9 with 5V signal
Default setting
COM1/2COM3/4COM5/6
JCSEL1
29-
-
JCSEL2
Page 32
2.14 <Power & FAN Connector >
The board requires onboard 4-pin DC 5V/12V power required, optional 5VSB for ATX.
2.14.1 <Power Input>
Connector: DC_IN
Type: 4-pin header
Pin Description Pin Description
1 +12V 3 Ground 2 Ground 4 +5V
DC_IN
30-
-
Page 33
2.14.2 <Power Input>
Connector: CN_PS Type: 3-pin connector
Pin Description
1 +5VSTBY 2 GND 3 +5V
31
CN_PS
Page 34
2.14.3 <Fan Connector>
Connector: SYSFAN Type: 3-pin fan wafer connector
Pin Description Pin Description Pin Description
1 Ground 2 +12V 3 CSFAN
Connector: CPUFAN Type: 4-pin fan wafer connector
Pin Description
1 Ground 2 +12V 3 P1FAN 4 +5V
CPUFAN
32
SYSFAN
Page 35
2.15 <Indicator and Switch>
The JFRNT provides front control panel of the board, such as power button, reset and beeper, etc. Please check well before you connecting the cables on the chassis.
Connector: JFRNT Type: onboard 14-pin (2 x 7) 2.54-pitch header
Function Signal PIN Signal Function
IDE LED
Reset
Power
Button
HDLED+ 1 2 PWDLED
Power
HDLED- 3 4 N/C
LED
Reset- 5 6 GND
GND 7 8 SPKIN+
N/C 9 10 N/C
Speaker
PWRBT+ 11 12 N/C
PWRBT- 13 14 SPKIN-
JFRNT
33
Page 36
Chapter 3 <System Configuration>
3.1 <Audio Configuration>
The board integrates Intel® ICH8-M with REALTEK® ALC888 codec. It can support 2-channel sound under system configuration. Please follow the steps below to setup your sound system.
1. Install REALTEK HD Audio driver.
2. Lunc h the control panel and Sound Effect Manager.
3. Select Speaker Configuration
4. Select the sound mode to meet your speaker system.
34
Page 37
3.2 <Video Memory Setup>
Based on Intel® Atom N450/D410/D510 chipset with GMA (Graphic Media Accelerator) 3150, the board supports Intel® DVMT (Dynamic Video Memory Technology) 3.0, which would allow the video memory be triggered up to 384MB. To support DVMT, you need to install the Intel GMA3150 Driver with supported OS.
BIOS Setup: On-Chip Frame Buffer Size:
This item can let you select video memory which been allocated for legacy VGA and SVGA graphics support and compatibility. The available option is 1MB and 8MB.
35
Page 38
This item can let you select a static amount of page-locked graphics memory; which will be allocated during driver initialization. Once you select the memory amount, it will be no longer available for system memory.
DVMT Memory Size:
This item can let you select a maximum size of dynamic amount usage of video memory, the system would configure the video memory depends on your appl ication, this item is strongly recommend to be selected as MAX DVMT.
Fixed + DVMT Memory Size:
You can select the fixed amount and the DV MT amount at the same time for a guarantee d video memory and additional dynamic video memory Notice:
1. The On-Chip Frame Buffer Size would be included in the Total GFX Memory Size.
36
Page 39
3.3 <Display Properties Setting>
Based on Intel® Atom N450/D410/D510 with GMA3150 (Graphic Media Accelerator), the board supports two DACs for display device as different resolution and color bit. Please install the Intel Graphic Driver before you starting setup display devices.
1. Click right button on the desktop to lunch display properties
2. Click Advanced button for more specificity setup.
37
Click Graphics Properties... for advanced setup
Page 40
3. This setup options can let you define each device settings.
Set the main display device here
Choose Intel® Dual
Display Clone to
setup the dual display mode as same screen
38
Page 41
Choose Extended
Desktop to setup
the dual display mode as different screen display
Choose Monitor to setup the CRT monitor for Colors, Resolution and Refresh Rate
39
Page 42
Chapter 4 <BIOS Setup>
The motherboard uses the Award BIOS for the system configuration. The Award BIOS in the single board computer is a customized version of the industrial standard BIOS for IBM PC AT-compatible computers. It supports Intel® x86 and compatible CPU architecture based processors and computers. The BIOS provides critical low-level support for the system central processing, memory and I/O sub-systems.
The BIOS setup program of the single board computer let the customers modif y the basic configuration setting. The settings are stored in a dedicated battery-backed memory, NVRAM, retains the information when the power is turned off. If the battery runs out of the power, then the settings of BIOS will come back to the default setting.
The BIOS section of the manual is subject to change without notice and is provi ded here for reference purpose only. The settings and configurations of the BIOS are current at the time of print, and therefore they may not be exactly the same as that displayed on your screen.
To activate CMOS Setup program, press <DEL> key immediately after you turn on the system. The following message “Press DEL to enter SETUP” should appear in the lower left hand corner of your screen. When you e nter the CMOS Setup Utility, the Main Menu will be displayed as Figure 4-1. You can use arrow keys to select your function, press Enter key to accept the selection and enter the sub-menu.
Figure 4-1 CMOS Setup Utility Main Screen
40
Page 43
Appendix A <I/O Port Pin Assignment>
A.1 < LPT Port >
Connector: CN_LPT Type: 25-pin header for LPT Port
Pin Description Pin Description
1 -PSTB 2 PRD0 3 PRD1 4 PRD2­5 PRD3 6 PRD4 7 PRD5 8 PRD6 9 PRD7 10 ACK­11 BUSY 12 PE 13 SLCT 14 AFD­15 ERR- 16 INIT­17 SLIN- 18 Ground 19 Ground 20 Ground 21 Ground 22 Ground 23 Ground 24 Ground 25 Ground
A.2 < CRT Port >
Connector: CRT Type: 15-pin D-sub female connector on rear panel
Pin Description Pin Description Pin Description
1 RED 6 Ground 11 N/C 2 GREEN 7 N/C 12 5VCDA 3 BLUE 8 Ground 13 5HSYNC 4 N/C 9 N/C 14 5VSYNC 5 -CRTATCH 10 -CRTATCH 15 5VCLK
41
Page 44
A.3 < LAN Port >
Connector: RJ45 Type: RJ45 connector with LED on rear panel
Pin 1 2 3 4 5 6 7 8
Description TRD0+ TRD0- TRD1+ TRD1- TRD2+ TRD2- TRD3+ TRD3-
8 1
A.4 < IrDA Port >
Connector: CN_IR Type: 5-pin header for SIR Port
Pin Description
1 +5V 2 N/C 3 IRRXD 4 Ground 5 IRTXD
A.5 < SMBUS Port >
Connector: CN_SMBUS Type: 5-pin header for SMBUS Port
Pin Description
1 +5V 2 N/C 3 SMDATA 4 SMCLK 5 Ground
42
Page 45
A.6 < DIO Port >
Connector: CN_DIO Type: 12-pin D-sub male connector on rear panel
Pin Description Pin Description
1 Ground 7 GP12 2 Ground 8 GP16 3 GP10 9 GP13 4 GP14 10 GP17 5 GP11 11 +5V 6 GP15 12 +12V
A.7 < IDE Port >
Connector: IDE Type: 10-pin D-sub male connector on rear panel
Pin Description Pin Description
1 Reset 2 Ground 3 D7 4 D8 5 D6 6 D9 7 D5 8 D10 9 D4 10 D11 11 D3 12 D12 13 D2 14 D13 15 D1 16 D14 17 D0 18 D15 19 Ground 20 N/C 21 REQ 22 Ground 23 IOW-/STOP 24 Ground 25 IOR-/HDMARDY 26 Ground 27 IORDY/DDMARDY 28 Ground 29 DACK- 30 Ground 31 IRQ 32 N/C 33 A1 34 SD 35 A0 36 A2 37 CS1 38 CS3 39 ASP1 40 Ground 41 Vcc 42 Vcc 43 Ground 44 Ground
43
Page 46
A.8 < Serial ATA Port >
Connector: SATA1/2/3 Type: 7-pin wafer connector
Pin 1 2 3 4 5 6 7
Description GND RSATA_TXP1 RSATA_TXN1 GND RSATA_RXN1 RSATA_RXP1 GND
17
A.9 < PS2 Port >
The PS/2 connector supports standard PS/2 keyboard directly or both PS/2 keyboard and mouse through for PS/2 Y-cable. Connector: PS2 Type: 6-pin Mini-DIN connector on bracket
Pin 1 2 3 4 5 6
Description KBCLK MSCLK GROUND VCC KBDATA MSDATA
A.10 < ATKB Port >
Connector: CN_ATKB Type: 5-pin box header
Pin 1 2 3 4 5
Description VCC GROUND N/C KBDATA KBCLK
44
Page 47
Appendix B <Flash BIOS>
B.1 BIOS Auto Flash Tool
The board is based on Award BIOS and can be updated easily by the BIOS auto flash tool. You can download the tool online at the address below:
TUhttp://www.award.comUT TUhttp://www.commell.com.tw/support/support.htmUT
File name of the tool is “awdflash.exe”, it’s the utility that can write the data into the BIOS flash ship and update the BIOS.
B.2 Flash Method
1. Please make a bootable floppy disk.
2. Get the last .bin files you want to update and copy it into the disk.
3. Copy awardflash.exe to the disk.
4. Power on the system and flash the BIOS. (Example: C:/ awardflash XXX.bin)
5. Re-star the system.
Any question about the BIOS re-flash please contact your distributors or visit the web-site at below:
http://www.commell.com.tw/support/support.htm
45
Page 48
Appendix C <System Resources>
C.1 <Direct memory access(DMA)> (HE-772A)
C.2<Input/output(IO)> (HE-772A)
46
Page 49
C.3<Interrupt reguest(IRQ)> (HE-772A)
47
Page 50
C.4<Memory> (HE-772A)
48
Page 51
49
Page 52
Appendix E <Watch Dog timer Setting >
The watchdog timer makes the system auto-reset while it stops to work for a period. The integrated watchdog timer can be setup as system reset mode by program.
Timeout Value Range
- 1 to 255
- Second or Minute
Program Sample
Watchdog timer setup as system reset with 5 second of timeout
2E, 87 2E, 87 2E, 07 2F, 08 Logical Device 8 2E, 30 2F, 01 Activate 2E, F5 2F, 00 Set as Second* 2E, F6 2F, 05 Set as 5
* Minute: bit 3 = 1; Second: bit 3 = 0
You can select Timer setting in the BIOS, after setting the time options, the system will reset according to the period of your selection.
50
Page 53
Contact Information
Any advice or comment about our products and service, or anything we can help you please don’t hesitate to contact with us. We will do our best to support you for your products, projects and business.
Taiwan Commate Computer Inc.
19F . , No.94, Sec. 1, Xintai 5th Rd., Xizhi Dist., New Taipei City
Address
TEL +886-2-26963909
FAX +886-2-26963911
22102, Taiwan
Website
E-Mail
Facebook
Twitter https://twitter.com/Taiwan_Commate
TUhttp://www.commell.com.twUT TUinfo@commell.com.twUT (General Information)
TUtech@commell.com.twUT (Technical Support)
https://www.facebook.com/pages/Taiwan-Commate-Computer-Inc/547993955271899
Commell is our trademark of industrial PC division
51
Loading...