COMMELL FS-A74 User Manual

FS-A74
PICMG1.3 Full-size CPU Card
User’s Manual
Edition 1.5
2014/05/15
FS-A74 User’s Manual
Copyright
Copyright 2011, all rights reserved. This document is copyrighted and all rights are reserved. The information in this document is subject to change without prior notice to make improvements to the products. This document contains proprietary information and pr otected by copyright. No part of this document may be reproduced, copied, or translated in any form or any means without prior written permission of the manufacturer. All trademarks and/or registered trademarks contains in this document are propert y of their respective owners.
Disclaimer
The company shall not be liable for any incidental or consequential damages resulting from the performance or use of this product. The company does not issue a warranty of any kind, express or implied, including without limitation implied warranties of merchantability or fitness for a particular purpose. The company has the right to revise the manual or include changes in the specifications of the product described within it at any time without notice and without obligation to notify any person of such revision or changes.
Trademark
All trademarks are the property of their respective holders.
Any questions please visit our website at TUhttp://www.commell.com.twUT
FS-A74 User’s Manual
(
)
(
)
Packing List:
Please check the package content before you starting using the board.
Hardware:
FS-A74 PICMG1.3 Full-size CPU Card motherboard x 1
Cable Kit:
SATA Cable x 2
(OALSATA3-L)/ (1040529)
DVI module with bracket x 1 (BADPDVIP_A & OALDVI-P)
(4120008021 & 1040075)
PS/2 Keyboard & Mouse Cable x 1
(OALPS2/MKN)/ (1040551)
4-pin to 3-pin ATX cable x 1
(OAL-ATX-C)/ (1040184)
DB25 & DB9 cable x 1
(FS-A74TDG/ FS-A74FTDG Only)
OAL1S1P)/ (1040041
Audio Port Cable x 1
(OALPJ-HD)/ (1040120)
USB Cable x 1
(OALUSBA-1)/ (1040172)
DB9 cable x 1 & DB25 cable x 1
(FS-A74TDG2/ FS-A74FTDG2 Only)
OAL2S1P)/ (1040191
Printed Matters:
Driver CD (Including User’s Manual) x 1
FS-A74 User’s Manual
Index
Chapter 1 <Introduction>.............................................................6
1.1 <Product Overview> ..................................................................................... 6
1.2 <Product Specification>................................................................................7
1.3 <Mechanical Drawing>.................................................................................9
1.4 <Block Diagram>........................................................................................10
Chapter 2 <Hardware Setup>..................................................11
2.1 <Connector Location>................................................................................ 11
2.2 <Jumper Location & Reference>................................................................ 12
2.3 <Connector Reference>.............................................................................13
2.3.1 <Internal Connectors>.............................................................. 13
2.3.2 <External Connectors>............................................................. 13
2.4 <CPU and Memory Setup>........................................................................ 14
2.4.1 <CPU Setup>.............................................................................14
2.4.2 <Memory installation>............................................................... 15
2.5 <CMOS & ATX Setup>............................................................................... 15
2.6 <Serial ATA Interface>................................................................................ 16
2.7 <Ethernet Interface>...................................................................................17
2.8 <Onboard Display Interface> .....................................................................18
2.8.1 <Analog Display>.......................................................................18
2.8.2 <DVI Display >...........................................................................19
2.9 <Integrated Audio Interface>...................................................................... 20
2.10 <USB Interface>.......................................................................................22
2.11 <Serial Port>............................................................................................. 24
2.12 <GPIO and SMBUS Interface>.................................................................26
2.13 <Power Supply and Fan Interface >......................................................... 27
2.14 <Switch and Indicator>.............................................................................28
Chapter 3 <System Setup>.......................................................29
3.1 <Audio Configuration>................................................................................ 29
3.2 <Display Properties Setting>......................................................................30
FS-A74 User’s Manual
Chapter 4 <BIOS Setup>.............................................................32
Appendix A <I/O Port Pin Assignment>..........................34
A.1 <Serial ATA Port>.......................................................................................34
A.2 <IrDA Port>.................................................................................................34
A.3 <VGA Port>................................................................................................34
A.4 <LAN Port>.................................................................................................34
A.5 <LAN LED Port>.........................................................................................35
A.6 <Parallel Port>............................................................................................35
Appendix B <Flash BIOS>.........................................................36
B.1 <Flash Tool> ...............................................................................................36
B.2 <Flash BIOS Procedure> ...........................................................................36
Appendix C <System Resources>......................................37
C.1 <I/O Port Address Map>.............................................................................37
C.2 <Memory Address Map>............................................................................39
C.3 <System IRQ Resources> .........................................................................40
Appendix D <Programming GPIO’s>.................................41
Appendix E <Programming Watchdog Timer >.........42
Contact Information.......................................................................43
FS-A74 User’s Manual
(This page is left for blank)
FS-A74 User’s Manual
Chapter 1 <Introduction>
1.1 <Product Overview>
FS-A74 the 2nd Generation Intel of the PICMG1.3 Full-size CPU Card motherboard,
nd
supports 2 Desktop Processor and features Intel Q67 chipset, integrated HD Graphics, DDR3 memory, REALTEK High Definition Audio, Serial ATA and Intel Gigabit LAN.
Intel® FCLGA1155 processor
The Intel® I3/I5/I7/Pentium/Xeon® processor now comes with a new form factor with 1155-pin FCLGA package, for 1066/1333MHz front-side-bus, 12MB L2 cache, for 65nm and 45nm manufacturing technology, the PLGA processor without pin header on solder side can make user installing the processor on the socket easier.
Intel® Q67 PCH chipset
The Intel Q67 integrates DDR3 1066/1333MHz for memory, and HD Graphic technology for new graphic engine. The Q67 integrates with up to 8 USB2.0 interfaces, and serial
Generation Intel® Core™ i7, Core™ i5, Core™ i3 and Pentium/Xeon ®
ATA II interface with RAID function.
FS-A74 User’s Manual
1.2 <Product Specification>
General Specification
Form Factor PICMG1.3 Full-size CPU Card CPU 2nd Generation Intel® Core™ I3/I5/I7/Pentium/Xeon® processor
With LGA1155 socket Package type: FCLGA 1155
Memory 2 x 240-pin DDR3 1066/1333MHz SDRAM up to 16GB
Unbufferred, none-ECC memory supported only Chipset Intel® BD82Q67 PCH BIOS Phoenix 16Mb SPI flash BIOS Green Function Power saving mode includes doze, standby and suspend modes.
ACPI version 1.0 and APM version 1.2 compliant Watchdog Timer System reset programmable watchdog timer with 1 ~ 255 sec./min.
of timeout value Real Time Clock Chipset built-in RTC with lithium battery Serial ATAII Intel® Q67 PCH integrates 4 Serial ATA II interface& 2 Serial ATA IIl
RAID 0, 1,5,10 Intel Matrix Storage Technology supported
Multi-I/O Port
Chipset Intel® Q67 PCH with Winbond® W83627DHG-P Controller Serial Port Four RS-232 and one RS232/422/485 serial ports USB Port Eight Hi-Speed USB 2.0 ports with 480Mbps of transfer rate IrDA Port One IrDA compliant Infrared interface supports SIR K/B & Mouse External PS/2 keyboard and mouse ports on rear I/O panel GPIO One 12-pin Digital I/O connector with 8-bit programmable I/O
Interface Smart Fan One CPU fan connectors for fan speed controllable
VGA Display Interface
Chipset Intel® Clear Video integrated HD Graphics Technology Frame Buffer Up to 1.7GB shared with system memory Display Type CRT, LCD monitor with analog display
Onboard DVI interface Connector External DB15 female connector on rear I/O panel
Onboard 26-pin DVI Connector
Ethernet Interface
Controller One Intel 82574L Gigabit Ethernet controller
One Intel 82579LM Gigabit Ethernet controller
(FS-A74TDG&FS-A74FTDG Only)
Type Triple speed 10/100/1000Base-T
Auto-switching Fast Ethernet
Full duplex, IEEE802.3U compliant Connector Two External RJ45 connectors with LED on rear I/O panel
7-
-
FS-A74 User’s Manual
Expansive Interface
PCI-Express One X16 and one X4 or X1 on PICMG 1.3 Interface PCI Four PCI bus master on PICMG 1.3 Interface
Audio Interface
Chipset Intel® integrated Q67with Realtek ALC888HD Audio
Intel High Definition Audio compliance Interface 2 channels sound output Connector Internal 10-pin header for line-out, MIC-in, 4-pin header for CD-IN
Power and Environment
Power
+5V, +12 DC input & 5VSB Requirement
Requirement Dimension 338 (L) x 126 (W) mm Temperature Operating within 0 ~ 60P
Storage within –20 ~ 85
O
p
C (32 ~ 140P
O
p
P
C (-4 ~ 185P
O
p
F)
O
p
F)
Ordering Code
FS-A74TDG Onboard VGA, DVI, 8 x USB2.0, 6 x serial Port, 6 x SATA, HD Audio,
GPIO, 2 x PCI Express mini card, 4 x PCI Bus master,
1 x Giga LAN (82579LM)
Support Four X1 & One X16 PCI Express interface
FS-A74FTDG Onboard VGA, DVI, 8 x USB2.0, 6 x serial Port, 6 x SATA, HD Audio,
GPIO, 2 x PCI Express mini card, 4 x PCI Bus master,
1 x Giga LAN (82579LM)
Support One X4 & One X16 PCI Express interface
FS-A74TDG2 Onboard VGA, DVI, 8 x USB2.0, 6 x serial Port, 6 x SATA, HD Audio,
GPIO, 2 x PCI Express mini card, 4 x PCI Bus master, 2 x Giga LAN
Support Four X1 & One X16 PCI Express interface
FS-A74FTDG2 Onboard VGA, DVI, 8 x USB2.0, 6 x serial Port, 6 x SATA, HD Audio,
GPIO, 2 x PCI Express mini card, 4 x PCI Bus master, 2 x Giga LAN
Support One X4 & One X16 PCI Express interface
The specifications may be different as the actual production.
8-
-
FS-A74 User’s Manual
1.3 <Mechanical Drawing>
-
9-
FS-A74 User’s Manual
1.4 <Block Diagram>
1 x PCI Express x 16
1 x DVI
1 x CRT
8 x USB 2.0
2nd Generation Intel® Core™
I3/I5/I7/Pentium/Xeon® processor
2 x 240-pin DDR3 1066/1333MHz up to 16GB
2 x PCI Express mini card
4 x SATAII & 2 x SATA III
Intel Q67
1 x Intel 82574L & 1 x 82579LM
2 x Serial ports
IrDA
8-bit GPIO
Parallel port
W83627D-P
SPI BIOS
25Q64CV
10-
-
4 x RS232
1 x PCI Express x4 or 4 x PCI Express x1 4 x PCI Bus master
FS-A74 User’s Manual
Chapter 2 <Hardware Setup>
2.1 <Connector Location>
CN_USB1
DDR3_A&B
SYSFAN CPUFAN
CN_PS DC_IN
CN_12V
JFRNT
SATA1/2/3/4/5/6
CN_DVI
CN_LPT
CN_SMBUS
CN_USB2 CN_USB3 CN_USB4
CN_DIO
MINI_CARD1&2
CN_AUDIO
JACT1 JSPD1
JACT2 JSPD2
COM6/5/4/3/2/1
CN_IR
FS-A74TDG2 & FS-A74FTDG2
PS2 RJ45_2 RJ45_1 CRT
FS-A74TDG & FS-A74FTDG
PS2 COM1 RJ45_1 CRT
11-
-
FS-A74 User’s Manual
2.2 <Jumper Location & Reference>
Jumper Function
JRTC CMOS Operating/Clear Setting JAT Power mode select JP1 Com1 Voltage Setting (For Pin 9) JP2 Com2 Voltage Setting (For Pin 9) JP3 Com3 Voltage Setting (For Pin 9) JP4 Com4 Voltage Setting (For Pin 9) JCSEL1
JCSEL2 JVUSB USB Voltage Setting
CN_COM2 RS-232 RS422 RS485 Setting CN_IR IrDA Setting
JVUSB JAT
Jumper: JAT Type: Onboard 3-pin jumper
JAT Mode
1-2 AT Power mode 2-3 ATX Power mode
Default setting
12-
-
JRTC
JCSEL2 JP4 JP3 JCSEL1 JP2 JP1
JAT
1 3
FS-A74 User’s Manual
2.3 <Connector Reference>
2.3.1 <Internal Connectors>
Connector Function Remark
CPU LGA1155 CPU socket DDRIIIA&B 240 –pin DDR3 SDRAM DIMM socket SATA 1/2 7-pin Serial ATAIII connector SATA 3/4/5/6 7-pin Serial ATAII connector CN_12V 4-pin +12V additional power supply connector CN_AUDIO 5 x 2-pin audio connector CDIN 4-pin CD-ROM audio input connector CN_DIO 6 x 2-pin digital I/O connector CN_USB 1/2/3/4/5/6 5 x 2-pin USB connector CPUFAN 4-pin CPU cooler fan connector SYSFAN 4-pin system cooler fan connector CN_IR 5-pin IrDA connector CN_COM1/2/3/4/5/6 9-pin com connector JFRNT 14-pin front panel switch/indicator connector Mini-Card1/2 2 x 52-pin Mini-PCIE socket CN_LPT 13 x 2-pin printer connector JSPD 1/2 LAN Speed LED connector JACT 1/2 LAN Activity LED connector CN_DVI 13 x 2-pin DVI connect
2.3.2 <External Connectors>
Connector Function Remark
RJ45 1/2 1 x RJ45 LAN connector CRT DB15 and analog VGA connector PS/2 PS/2 keyboard and mouse connector
13-
-
FS-A74 User’s Manual
p
2.4 <CPU and Memory Setup>
2.4.1 <CPU Setup>
FS-A74 has a LGA1155 CPU socket onboard; please chec k following steps to install the
processor properly.
Attention If FS-A74 need RMA please Keep CPU socket cover on the CPU Socket. Warning If CPU Socket internal Pin damage We could not provide warranty.
2nd Generation Intel® Core™ I3/I5/I7/Pentium/Xeon® processor Package type: 1155 pin FCLGA
FSB: 1066/1333MHz
1. Lift this bar
4. Lock this bar
2. Uncover this plate
Checked point
3. Place the CPU on the top of ins
the
3. Cover this plate
Notice: Please place the CPU on the pins tenderlyto avoid bending the pins
14
FS-A74 User’s Manual
2.4.2 <Memory installation>
FS-A74 has two 240-pin DDR3 DIMM support up to 16GB of memory capacity. The
memory frequency supports 1066/1333 MHz. Only Non-ECC memory is supported.
DDRIIIA&B
2.5 <CMOS Setup>
The board’s data of CMOS can be setting in BIOS. If the board refuses to boot due to inappropriate CMOS settings, here is ho w to proceed to clear (reset) the CMOS to its default values.
Jumper: JRTC Type: Onboard 3-pin jumper
JRTC Mode
1-2 Clear CMOS 2-3 Normal Operation
Default setting: 2-3
JRTC
15-
-
1 3
FS-A74 User’s Manual
2.6 <Serial ATA Interface>
FS-A74 has Four Serial ATA II & Two Serial ATA III interfaces with RAID function, the
transfer rate of the Serial ATA II can be up to 300MB/s & Serial ATA III can be up to 600MB/s. Please go to http://www.serialata.org/ information. Based on Intel® PCH, it supports Intel® Matrix Storage Technology with combination of RAID 0,1,5 and 10. The main features of RAID on Intel® Q67 PCH are listed below:
1. Supports for up to RAID volumes on a single, two-hard drive RAID array.
2. Supports for two, two-hard drive RAID arrays on any of six Serial ATA ports.
3. Supports for Serial ATA ATAPI devices.
4. Supports for RAID spares and automatic rebuild.
5. Supports on RAID arrays, including NCQ and native hot plug.
For more information please visit Intel’s official website.
For more about the system setup for Serial ATA, please check the chapter of SATA configuration.
for more about Serial ATA technology
SATA1/2/3/4/5/6
16-
-
FS-A74 User’s Manual
2.7 <Ethernet Interface>
The board integrates with one Intel 82574L Gigabit Ethernet & one Intel 82579LM controllers, as the PCI Express bus. The Intel 82574L supports triple speed of 10/100/1000Base-T, with IEEE802.3 compliance and Wake-On-LAN supported.
82574L 82579LM
PS2 RJ45_2 RJ45_1 CRT
82579LM
PS2 COM1 RJ45_1 CRT
FS-A74 TDG2 & FS-A74FTDG2
FS-A74TDG & FS-A74FTDG
17-
-
FS-A74 User’s Manual
2.8 <Onboard Display Interface>
Based on Intel Q67 chipset with built-in graphics, the board provides one DB15 Connector on real external I/O port and the board also provides 26-pin DVI interface
Notice: When you install any PCI Graphic card, the onboard graphics would be disabled automatically.
2.8.1 <Analog Display>
Please connect your CRT or LCD monitor with DB15 male connector to the onboard DB15 female connector on rear I/O port.
FS-A74TDG2 & FS-A74FTDG2
CRT
FS-A74TDG & FS-A74FTDG
CRT
18-
-
FS-A74 User’s Manual
2.8.2 <DVI Display >
The board also comes with a DVI interface with Chrontel for digital video interface. Connector: CN_DVI Connector type: 26-pin header connector (pitch = 2.00mm)
Pin Number Assignment Pin Number Assignment
1 TX1+ 2 TX1­3 Ground 4 Ground 5 TXC+ 6 TXC­7 Ground 8 PVDD 9 N/C 10 N/C
11 TX2+ 12 TX2­13 Ground 14 Ground 15 TX0+ 16 TX0­17 N/C 18 HPDET 19 DDCDATA 20 DDCCLK 21 GND 22 N/C 23 N/C 24 N/C 25 N/C 26 N/C
2 26
1 25
CN_DVI
19-
-
FS-A74 User’s Manual
2.9 <Integrated Audio Interface>
The board integrates onboard audio interface with REALTEK ALC888 codec, with Intel next generation of audio standard as High Definition Audio, it offers more vivid sound and other advantages than former HD audio compliance. The main specifications of ALC888 are:
z High-performance DACs with 100dB S/N ratio z 2 DAC channels support 16/20/24-bit PCM format for 2 audio solution z 16/20/24-bit S/PDIF-OUT supports 44.1K/48K/96kHz sample rate z Compatible with HD z Meets Microsoft WHQL/WLP 2.0 audio requirements
The board provides 2 channels audio phone jacks on rear I/O port, Line-in/MIC-in ports for front I/O panel through optional cable.
CN_AUDIO
10 9
CDIN
20-
-
1 4
2 1
FS-A74 User’s Manual
Connector: CN_AUDIO
2 10
Type: 10-pin (2 x 5) header (pitch = 2.54mm)
1
Pin Description Pin Description
1 MIC_L 2 Ground 3 MIC_R 4 N/C 5 Speaker_R 6 MIC Detect 7 SENSE 8 N/C 9 Speaker_L 10 Speaker Detect
Connector: CDIN
4
Type: 4-pin header (pitch = 2.54mm)
Pin Description
1
1 CD – Left 2 Ground 3 Ground 4 CD – Right
9
21-
-
FS-A74 User’s Manual
2.10 <USB Interface>
FS-A74 integrates eight USB2.0 ports. The specifications of USB2.0 are listed
below:
Interface USB2.0
CN_USB1
10 2 9
1
Connector: CN_USB1/2/3/4
Controller
Transfer Rate Up to 480Mb/s
Voltage 5V
Intel® Q67
CN_USB2 CN_USB3 CN_USB4
1
102
9
JVUSB
2 6 1 5
Type: 10-pin (2 x 5) header (pitch = 2.54mm)
Pin Description Pin Description
1 VCC (5V_SB/ 5V) 2 VCC (5V_SB/ 5V) 3 Data0- 4 Data1­5 Data0+ 6 Data1+ 7 Ground 8 Ground 9 Ground 10 N/C
22-
-
FS-A74 User’s Manual
Jumper: JVUSB Type: Onboard 6-pin jumper
JAT Mode
4-6 & 3-5 +5V_SB 2-4 & 1-3 +5V
Default setting
Effective patterns of connection: 1-3 & 2-4 or 3-5 & 4-6
2 6 1 5
Warning: others cause damages
6
2
5
1
23-
-
FS-A74 User’s Manual
2.11 <Serial Port>
The board supports five RS232 serial port and one jumper selectable RS232/422/485 serial ports. The jumper JCSEL1 & JCSEL2 can let you configure the communicating modes for COM2.
Connector: CN_COM1/3/4/5/6 Type: 9-Pin box header
Pin Description Pin Description
1 DCD 2 RXD 3 TXD 4 DTR 5 GND 6 DSR 7 RTS 8 CTS 9 RI 10 N/C
Connector: CN_COM2
Type: 9-Pin box header
Pin Description Pin Description
1 DCD/422TX-/485- 2 RXD/422TX+/485+ 3 TXD/422RX+ 4 DTR/422RX­5 GND 6 DSR 7 RTS 8 CTS 9 RI 10 N/C
Setting RS-232 & RS-422 & RS-485 for COM2
CN_COM6/5/4/3/2/1
10 9
2 1
24
FS-A74 User’s Manual
8
Function JCSEL2 JCSEL1
IrDA
RS-422
RS-232
Default setting:
RS-485
JCSEL1: (1-3, 2-4, 7-9, 8-10) JCSEL2: (1-2)
7
2
1
8
7
JCSEL2 JP4 JP3 JCSEL1 JP2 JP1
1
2
7
8
1 2
8
7
2
1
2
1 2
1
2
1
2
1
12
11
12
11
12
11
12
11
Jumper: JP1/JP2/JP3/JP4 (COM1/2/3/4) Type: onboard 6-pin header
Power Mode JP1/2/3/4
Pin 9 with 5V Power 1-2 Pin 9 with 12V Power 3-4 Standard COM port
Default setting (5-6)
5-6
25
FS-A74 User’s Manual
2.12 <GPIO and SMBUS Interface>
The board provides a programmable 8-bit digital I/O interface; you can use this general purpose I/O port for system control like POS or KIOSK.
Connector: CN_DIO Type: 12-pin (6 x 2) header (pitch = 2.0mm)
Pin Description Pin Description
1 Ground 2 Ground 3 GP10 4 GP14 5 GP11 6 GP15 7 GP12 8 GP16 9 GP13 10 GP17 11 5V 12 12V
Connector: CN_SMBUS Type: 5-pin header for SMBUS Ports
Pin Description
1 VCC 2 N/C 3 SMBDATA 4 SMBCLK 5 Ground
CN_SMBUS
26-
-
1
5
1 2
CN_DIO
11 12
FS-A74 User’s Manual
2.13 <Power Supply and Fan Interface >
The FS-A74 provides a standard ATX power supply with 4-pin ATX connector and the board provides one 4-pin fan connector supporting smart fan for CPU cooler and one 4-pin cooler fan connectors for system and Northbridge chip. please connect this well before you finishing the system setup.
Connector: DC_IN Type: 4-pin DC power connector
Pin Description Pin Description
1 +12V 2 Ground 3 Ground 4 +5V
Connector: CPUFAN Type: 4-pin fan wafer connector
Pin Description Pin Description
1 Ground 2 +12V 3 Fan Speed Detection 4 Fan Control
Connector: SYSFAN Type: 3-pin fan wafer connector
Pin Description Pin Description
1 Ground 2 +12V 3 Fan Speed Detection 4 Will be defined
Connector: CN_PS Type: 3-pin connector
Pin Description Pin Description Pin Description
1 5VSTBY 2 Ground 3 PSON
4
DC_IN
1
4
CPUFAN
4
SYSFAN
3
CN_PS
1
27-
-
FS-A74 User’s Manual
2.14 <Switch and Indicator>
The JFRNT provides front control panel of the board, such as power button, reset and beeper, etc. Please check well before you connecting the cables on the chassis.
Connector: JFRNT Type: onboard 14-pin (2 x 7) 2.54-pitch header
Function Signal PIN Signal Function
IDE LED
Reset
Power Button
HDLED+ 1 2 PWRLED+
PWRBT+ 11 12 N/C
PWRBT- 13 14 SPK-
HDLED- 3 4 N/C
Power
LED
Reset+ 5 6 PWRLED-
Reset- 7 8 SPK+
N/C 9 10 N/C
Speaker
14 2 13
JFRNT
1
-
28-
FS-A74 User’s Manual
Chapter 3 <System Setup>
3.1 <Audio Configuration>
The board integrates Intel® Q67 with REALTEK® ALC888 code. It can support 2-channel sound under system configuration. Please follow the steps below to setup your sound system.
1. Install REALTEK HD Audio driver.
2. Lunch the control panel and Sound Effect Manager.
3. Select Speaker Configuration
29-
-
FS-A74 User’s Manual
3.2 <Display Properties Setting>
Based on Intel Q67 with HD Graphic, the board supports two DACs for display device as different resolution and color bit. Please install the Intel Graphic Driver before you starting setup display devices.
1. Click right button on the desktop to lunch display properties
2. Click Advanced button for more specificity setup.
Click Graphics Properties... for advanced setup
30-
-
FS-A74 User’s Manual
3. This setup options can let you define each device settings.
Click Monitor to setup the CRT monitor for Resolution and Refresh Rate
Click Intel® Dual Display
Clone to setup the dual
display mode as same screen
31-
-
FS-A74 User’s Manual
Chapter 4 <BIOS Setup>
The motherboard uses the Phoenix BIOS for the system configuration. The Phoenix BIOS in the single board computer is a customized version of the industrial standard BIOS for IBM PC AT-compatible computers. It supports Intel x86 and compatible CPU architecture based processors and computers. The BIOS provides critical low-level support for the system central processing, memory and I/O sub-systems.
The BIOS setup program of the single board computer let the customers modify the basic
configuration setting. The settings are stored in a dedicated battery-backed memory, NVRAM, retains the information when the power is turned off. If the battery runs out of the power, then the settings of BIOS will come back to the default setting.
The BIOS section of the manual is subject to change without notice and is provided h ere
for reference purpose only. The settings and configurations of the BIOS are current at the time of print, and therefore they may not be exactly the same as that displayed on your screen.
To activate CMOS Setup program, press <DEL> key immediately after you turn on the
system. The following message “Press DEL to enter SETUP” should appear in the lower left hand corner of your screen. When you enter the CMOS Setup Utility, the Main Menu will be displayed as Figure 4-1. You can use arrow keys to select your function, press Enter key to accept the selection and enter the sub-menu.
Figure 4-1 CMOS Setup Utility Main Screen
32-
-
FS-A74 User’s Manual
(This page is left for blank)
-
33-
FS-A74 User’s Manual
jump
Appendix A <I/O Port Pin Assignment>
A.1 <Serial ATA Port>
Connector: SATA1/2/3/4/5/6 Type: 7-pin wafer connector
1 2 3 4 5 6 7
GND RSATA_TXP1 RSATA_TXN1 GND RSATA_RXN1 RSATA_RXP1 GND
7 1
A.2 <IrDA Port>
Connector: CN_IR Type: 5-pin header for SIR Ports
Pin Description
1 VCC 2 N/C 3 IRRX 4 Ground 5 IRTX
A.3 <VGA Port>
Connector: CRT Type: 15-pin D-sub female connector on bracket
Pin Description Pin Description Pin Description
1 RED 6 Ground 11 N/C 2 GREEN 7 Ground 12 DDCDA 3 BLUE 8 Ground 13 HSYNC 4 N/C 9 N/C 14 VSYNC 5 Ground 10 Ground 15 DDCCLK
JCSEL1 must
1
5
to “SIR
6
1 2 3 4 5
10
11 12 13 14 15
A.4 <LAN Port>
Connector: RJ45 Type: RJ45 connector with LED on bracket
Pin 1 2 3 4 5 6 7 8
Description MI0+ MI0- MI1+ MI2+ MI2- MI1- MI3+ MI3-
-
34-
8 1
FS-A74 User’s Manual
A.5 <LAN LED Port>
Connector: JSPD1/2 Type: 5-pin header for LAN Speed LED connector
When Lan speed 10/100Mbps
Pin Description
1 LED­2 LED+
When Lan speed 1Gbps
Pin Description
1 LED+ 2 LED-
Connector: JATC1/2 Type: 5-pin header for LAN Activity LED connector
Pin Description
1 LED­2 LED+
2
2
1
1
A.6 <Parallel Port>
Connector: LPT Type: 26-Pin box header
Pin Description Pin Description
1 -PSTB 14 AFD­2 PRO0 15 ERR­3 PRO1 16 INT­4 PRO2 17 SLIN­5 PRO3 18 Ground 6 PRO4 19 Ground 7 PRO5 20 Ground 8 PRO6 21 Ground 9 PRO7 22 Ground 10 ACK- 23 Ground 11 BUSY 24 Ground 12 PE 25 Ground 13 SLCT 26 N/C
-
35-
14 26
1
13
FS-A74 User’s Manual
Appendix B <Flash BIOS>
B.1 <Flash Tool>
The board is based on Phoenix BIOS and can be updated easily by the BIOS auto flash tool. You can download the tool online at the address below:
http://www.phoenix.com/en/home/ http://www.commell.com.tw/Support/Support_SBC.htm
File name of the tool is “Pflash.exe”, it’s the utility that can write the data into the BIOS flash ship and update the BIOS.
B.2 <Flash BIOS Procedure>
1. Please make a bootable floppy disk.
2. Get the last .bin files you want to update and copy it into the disk.
3. Copy Pflash.exe to the disk.
4. Power on the system and flash the BIOS.
(Example: C:/Pflash/bbl/cvar/sa XXX.bin)
5. Restart the system.
Any question about the BIOS re-flash please contact your distributors or visit the web-site at below:
http://www.commell.com.tw/support/support.htm
UT
-
36-
FS-A74 User’s Manual
Appendix C <System Resources>
C.1 <I/O Port Address Map>
-
37-
FS-A74 User’s Manual
-
38-
FS-A74 User’s Manual
C.2 <Memory Address Map> Memory:
-
39-
FS-A74 User’s Manual
C.3 <System IRQ Resources> IRQ:
-
40-
FS-A74 User’s Manual
Appendix D <Programming GPIO’s>
The GPIO’can be programmed with the MSDOS debug program using simple IN/OUT commands.The following lines show an example how to do this.
GPIO0…..GPIO7 bit0……bit7
-o 2 E 87 ;enter configuration
-o 2E 87
-o 2E 07
-o 2F 09 ;enale GPIO function
-o 2E 30
-o 2F 02 ;enable GPIO configuration
-o 2E F0
-o 2F xx ;set GPIO as input/output; set ‘1’ for input,’0’for output
-o 2E F1
-o 2F xx ;if set GPIO’s as output,in this register its value can be set
Optional :
-o 2E F2
-o 2F xx ; Data inversion register ; ‘1’ inverts the current valus of the bits ,’0’ leaves them as they are
-o 2E 30
-o 2F 01 ; active GPIO’s
For further information, please refer to Winbond W83627DHG-P datasheet.
41-
-
FS-A74 User’s Manual
Appendix E <Programming Watchdog Timer >
The watchdog timer makes the system auto-reset while it stops to work for a period. The integrated watchdog timer can be setup as system reset mode by program.
Timeout Value Range
- 1 to 255
- Second or Minute
Program Sample
Watchdog timer setup as system reset with 5 second of timeout
2E, 87 2E, 87 2E, 07 2F, 08 Logical Device 8 2E, 30 Activate 2F, 01 2E, F5 Set as Second* 2F, 00 2E, F6 Set as 5 2F, 05
* Minute: bit 3 = 0; Second: bit 3 = 1
You can select Timer setting in the BIOS, after setting the time options, the system will reset according to the period of your selection.
42-
-
FS-A74 User’s Manual
Contact Information
Any advice or comment about our products and service, or anything we can help you please don’t hesitate to contact with us. We will do our best to support you for your products, projects and business.
Taiwan Commate Computer Inc.
19F., No.94, Sec. 1, Xintai 5th Rd., Xizhi Dist., New Taipei
Address
TEL +886-2-26963909 FAX +886-2-26963911
City 22102, Taiwan
Website
E-Mail
Facebook
Twitter https://twitter.com/Taiwan_Commate
TUhttp://www.commell.com.twUT TUinfo@commell.com.twUT (General Information)
TUtech@commell.com.twUT (Technical Support)
https://www.facebook.com/pages/Taiwan-Commate-Computer-Inc/547993955271899
Commell is a brand name of Taiwan commate computer Inc.
43-
-
Loading...