COMMELL FS-97E User Manual

Page 1
FS-97E
Full-size PICMG CPU Card
User’s Manual
Edition 1.2
2009/7/14
Page 2
Copyright
Copyright 2009, all rights reserved. This document is copyrighted and all rights are reserved. The information in this document is subject to change without prior notice to make improvements to the products. This document contains proprietary information and protect ed by copyright. No part of this document may be reproduced, copied, or translated in any form or any means without prior written permission of the manufacturer. All trademarks and/or registered trademarks contains in this docum ent are property of their respective owners.
Disclaimer
The company shall not be liable for any incidental or consequential damages resulting from the performance or use of this product. The company does not issue a warranty of any kind, e xpress or implied, including without limitation implied warranties of merchantability or fitness for a particular purpose. The company has the right to revise the manual or include changes in the specifications of the product described within it at any time without notice and without obligation to notify any person of such revision or changes.
Trademark
All trademarks are the property of their respective holders.
Any questions please visit our website at TUhttp://www.commell.com.twUT
-1-
Page 3
Packing List:
Please check the package content before you starting using the board.
Hardware:
FS-97E Full-size PICMG CPU Card x 1
Cable Kit:
HD Audio Port Cable x 1
DVI module with DVI Cable x 1 (FS-97EXDG & FS-97EXDG2)
PS/2 Keyboard & Mouse Cable x 1
SATA Cable x 2
USB Cable x 2
FDD cable x 1
CPU Cooler x 1
40-pin ATA100 IDE cable x 1
ATX cable x 1
-2-
Page 4
Printer cable x 1
(FS-97EXG2 & FS-97EXDG2)
COM & Printer cable x 1
(FS-97EXG & FS-97EXDG)
Printed Matters:
Driver CD x 1 (including User’s Manual) VT-6421_RAID & ICH9M_AHCI disk driver x1
Com Cable x 1
(FS-97EXG2 & FS-97EXDG2)
HDTV Port Cable x 1 (Optional)
-3-
Page 5
Index
Chapter 1 <Introduction>.......................................................................................7
1.1 <Product Overview>..................................................................................7
1.2 <Product Specification>.............................................................................8
1.3 <Mechanical Drawing>............................................................................10
1.4 <Block Diagram>.....................................................................................11
Chapter 2 <Hardware Setup>...............................................................................12
2.1 <Connector Location>.............................................................................12
2.2 <Connector Reference>..........................................................................13
2.2.1 <Internal Connectors> ................................................................13
2.2.2 <External Connectors>...............................................................13
2.3 <Jumper Location & Reference>.............................................................14
2.4 <CPU and Memory Setup>.....................................................................15
2.4.1 <CPU Setup>..............................................................................15
2.4.2 <Memory Setup> ........................................................................16
2.5 <CMOS Setup>.......................................................................................17
2.6 <Serial ATA Interface>.............................................................................18
2.7 <Ethernet Interface>................................................................................19
2.8 <Onboard Display Interface> ..................................................................20
2.8.1 <Analog VGA Interface>.............................................................20
2.8.2 <Digital Display>.........................................................................21
2.8.3 <HDTV Interface>.......................................................................25
2.8.4 <DVI Interface >..........................................................................26
2.9 <Integrated Audio Interface>...................................................................27
2.10 <GPIO Interface>..................................................................................29
2.11 <Power and Fan Installation>................................................................30
2.11.1 <Power connectors>.................................................................30
2.11.2 <Fan Connectors> ....................................................................30
2.11.3 <ATX Power Mode>..................................................................32
2.12 <Switch and Indicator>..........................................................................33
-4-
Page 6
Chapter 3 <System Setup> ..................................................................................34
3.1 <OS installation Guide> ..........................................................................34
3.2 <Audio Configuration>.............................................................................35
3.3 <Video Memory Setup>...........................................................................36
3.4 <Display Properties Setting>...................................................................37
Chapter 4 <BIOS Setup> ......................................................................................39
Appendix A <I/O Port Pin Assignment>..............................................................41
A.1 <Serial ATA Port>....................................................................................41
A.2 <IrDA Port>.............................................................................................41
A.3 <SMBUS Port> .......................................................................................42
A.4 <Serial Port 2>........................................................................................42
A.5 < RS-232, RS-422, RS-485 & IrDA >......................................................43
A.6 <Parallel Port>........................................................................................44
A.7 <LAN Port>.............................................................................................44
A.8 <USB Interface> .....................................................................................44
A.9 <DVI Port>..............................................................................................45
A.10 <PS/2 Keyboard & Mouse Port>...........................................................45
Appendix B <Flash BIOS>....................................................................................46
B.1 <Flash Tool>...........................................................................................46
B.2 <Flash BIOS Procedure>........................................................................46
Appendix C <System Resources>.......................................................................47
C.1 <Direct Memory Access (DMA)> ............................................................47
C.2 <Direct Memory Access (IRQ)>..............................................................47
C.3 <Input /Output (IO)>................................................................................48
C.4 <Memory Address Map> ........................................................................ 50
Appendix D <Programming GPIO’s>...................................................................51
Appendix E <Programming Watchdog Timer>...................................................52
Contact Information..............................................................................................53
-5-
Page 7
(This page is left for blank)
-6-
Page 8
Chapter 1 <Introduction>
1.1 <Product Overview>
FS-97E the new generation of the Full-size PICMG CPU Card, supports Intel Penryn
Processor for 667/800/1066 MHz front side bus and features Intel GM45 and ICH9M chipset, integrated GMA 4500MHD graphics, DDR3 memory, REALTEK ALC888 High Definition Audio, Serial ATA and two Intel Gigabit LAN.
Intel Penryn Processor
The board supports Intel Penryn processor with 667/800/1066 MHz front side bus, L2 Cache: All specification depends on the CPU(1M/2M/3M/4M/6M). To provides more powerful performance than before.
New features for Intel GM45 chipset
The board integrates Intel GM45 and ICH9M chipset, to provide new generation of the mobile solution, supports Intel GMA 4500MHD graphics, DDR3 800/1066MHz memory, built-in high-speed mass storage interface of serial ATA, High Definition Audio with 2 channels surrounding sound.
All in One multimedia solution
Based on Intel GM45 and ICH9M chipset, the board provides high performance onboard graphics, 24-bit dual channel LVDS interface, HDTV and 2 channels High Definition Audio, to meet the very requirement of the multimedia application.
Flexible Extension Interface
The board provides one PCI Express mini card (FS-97EXDG & FS-97EXDG2 only), two PCI Express mini card (FS-97EXG & FS-97EXG2 only) one mini-PCI socket and one CF socket.
7-
-
Page 9
1.2 <Product Specification>
General Specification
Form Factor Full-size PICMG CPU Card
PICMG version 1.0 (Rev. 2.0), PCI version 2.0 compliant
CPU Support Intel Penryn Processor
Package type: Micro-FCPGA478 (Socket-P) L2 Cache: All specification depends on the CPU (1M/2M/3M/4M/6M) Front side bus: 667/800/1066 MHz
Memory 2 x 800/1066MHz DDRIII 204-pin SO-DIMM up to 8GB Chipset Intel® GM45 and ICH9M (82801IBM) BIOS Phoenix-Award v6.00PG 8Mb SPI flash BIOS Green Function Watchdog Timer Real Time Clock IDE UltraATA133 IDE interface supports up to 2 ATAPI devices
Serial ATA Intel® ICH9M built-in 3 x SATAII interface up to 300MB/s
Multi-I/O Port
Chipset Intel® ICH9M with Winbond® W83627DHG controller Serial Port Two RS232 and one jumper selectable RS232/422/485 Parallel Port One internal bi-direction parallel port with SPP/ECP/EPP mode Floppy Port One internal Floppy port USB Port 8 x Hi-Speed USB 2.0 ports with 480Mbps of transfer rate IrDA Port One IrDA compliant Infrared interface supports SIR K/B & Mouse PS/2 keyboard and mouse port on bracket GPIO One 12-pin Digital I/O connector with 8-bit programmable
VGA Display Interface
Chipset Intel® GM45 & ICH9M Memory Up to 1024MB shared with system memory Display Type CRT, LCD monitor with analog display, DVI, HDTV Connector External DB15 female connector
Power saving mode includes doze, standby and suspend modes. ACPI version 2.0 and APM version 1.2 compliant System reset programmable watchdog timer with 1 ~ 255 sec./min. of timeout value Chipset integrated RTC with onboard lithium battery
One 40-pin IDE port onboard with VT-6421
VIA VT-6421 built-in 2 x SATAI interface up to 150MB/s
(support RAID 0,1)
Onboard 40-Pin LVDS connector Onboard 26-Pin DVI connector (FS-97EXDG/XDG2) Onboard 9-Pin TV-out connector
8-
-
Page 10
Ethernet Interface
Chipset Intel 82574L Gigabit Ethernet controller Type Triple speed 10/100/1000Base-T
auto-switching Fast Ethernet Full duplex, IEEE802.3U compliant
Connector External two RJ45 connector with LED on rear I/O panel
Audio Interface
Chipset Intel® ICH9M with Realtek ALC888 HD Audio
Intel High Definition Audio compliance Interface 2 channels sound output Connector Internal 10-pin header for line-in/-out, MIC-in, 4-pin for CD-IN
Solid State Disk Interface
Flash Type Compact Flash TypeII for Compact Flash Card with VT-6421
ISA Interface
ISA Bridge Winbond W83628G & W83629G Function I/O & IRQ supported only, no support DMA & bus mastering
Expansive Interface
Mini PCI Up to 2 x Mini PCI socket (optional)
1 x Mini PCI (standard) PCI express Mini card
Up to 3 x PCI express mini card socket (optional)
1 x PCI express mini card socket (FS-97EXDG/FS-97EXDG2)
2 x PCI express mini card socket (FS-97EXG/FS-97EXG2)
Power and Environment
Power
+5V, +12 DC input & 5V
Requirement
SB
Requirement Dimension 338 (L) x 122 (W) mm Temperature Operating within 0 ~ 60 P
Storage within -20 ~ 85
o
P
C (32 ~ 140P
o
P
P
C (-4 ~ 185P
o
P
F)
o
P
F)
Ordering Code
FS-97EXG Onboard VGA, LVDS, HDTV, IDE, CF, SATA, COM, USB2.0,
Mini PCI, HD Audio, 2 x PCI Express mini card, 1 x Gigabit
LAN. FS-97EXG2 Onboard VGA, LVDS, HDTV, IDE, CF, SATA, COM, USB2.0,
Mini PCI, HD Audio, 2 x PCI Express mini card, 2 x Gigabit
LAN. FS-97EXDG Onboard VGA, LVDS, HDTV, IDE, CF, SATA, COM, USB2.0,
Mini PCI, HD Audio, DVI, 1 x PCI Express mini card, 1 x
Gigabit LAN. FS-97EXDG2 Onboard VGA, LVDS, HDTV, IDE, CF, SATA, COM, USB2.0,
Mini PCI, HD Audio, DVI, 1 x PCI Express mini card, 2 x
Gigabit LAN.
-
9-
Page 11
1.3 <Mechanical Drawing>
10-
-
Page 12
FS-97E User’s Manual
VT
1.4 <Block Diagram>
Intel GMA X4500MHD
1 x LVDS
Intel Penryn Processor
2 x 204-pin DDR3 SO-DIMM 800/1066MHz up to 8GB
1 x HDTV
1 x DVI (FS-97EXDG/G2)
8 x USB2.0 ports
3 x SATAII
300MB/S
1 x IDE
1 x CF
2 x SATAI
150MB/S
-6421
ISA Bridge
GM45
ICH9M
SPI
1 x PCI express mini card (FS-97EXG/G2)
1 x Mini PCI
(second optional)
1 x PCI express mini card
(second optional)
2 x LAN Intel 82574L
ALC888 HD Audio
W83627DHG
-
11-
BIOS
1 x RS422/485/232/IR 1 x com, FDD, LPT & GPIO
Page 13
FS-97E User’s Manual
Chapter 2 <Hardware Setup>
2.1 <Connector Location>
DC_IN
CN_PS
CPUFAN
CN_DVI
JFRNT
CN_HDTV
CN_INV
SO-DIMM2
CN_LVDS
MINI_CARD1
FDD
SATA1/2/3/4/5
IDE
MINIPCI2 (optional)
CF
MINI_CARD2
FS-97EXG2 & FS-97EXDG2
PS2 LAN2 LAN1 CRT
CN_USB1/2/3/4
MINI_CARD3
(optional)
MINIPCI1
CN_LPT
CN_COM1/2
CN_DIO
CN_AUDIO
CD_IN
CN_SMBUS CN_IR
CN_ATKB
FS-97EXG & FS-97EXDG
PS2 COM LAN1 CRT
-
12-
Page 14
FS-97E User’s Manual
2.2 <Connector Reference>
2.2.1 <Internal Connectors>
Connector Function Remark
CPU Socket 478 for socket-P CPU SO-DIMM1/2 204-pin DDR3 SO-DIMM socket IDE 40-pin primary IDE connector CN_LPT 26-pin LPT port connector FDD 34-pin floppy connector SATA1/2/3/4/5 7-pin Serial ATA connector DC_IN 4-pin AT power supply connector CN_PS 3-pin power input connector CN_AUDIO 5 x 2-pin audio connector CD_IN 4-pin CD-ROM audio input connector CN_DIO 6 x 2-pin digital I/O connector CN_USB 5 x 2-pin USB connector CPUFAN 4-pin CPU cooler fan connector SYSFAN 3-pin system cooler fan connector CN_DVI 13 x 2-pin DVI interface (FS-97EXDG/G2) CN_HDTV 5 x 2-pin HDTV interface CN_LVDS 20 x 2-pin LVDS connector CN_INV 5-pin LCD inverter connector CN_IR 5-pin IrDA connector CN_ATKB 5-pin AT keyboard connector JFRNT 14-pin front panel switch/indicator
connector MiniPCI 124-pin Mini-PCI socket Type IIIA PCI express mini card COM 1/2 Serial port 1/2 connector (FS-97EXG2/XDG2) COM 2 Serial port 2 connector (FS-97EXG/XDG)
52-pin PCI express mini card socket
2.2.2 <External Connectors>
Connector Function Remark
CRT DB15 VGA connector PS2 PS2 keyboard & mouse RJ45_1/2 RJ45 LAN 1/2 connector (FS-97EXG2/XDG2) RJ45_1 RJ45 LAN 1 connector (FS-97EXG/XDG) COM 1 Serial port 1 connector (FS-97EXG/XDG)
-
13-
Page 15
FS-97E User’s Manual
2.3 <Jumper Location & Reference>
Jumper Function
JRTC CMOS Operating/Clear Setting JVLCD Panel Voltage Setting JAT Power mode select JCSEL1/2 CN_COM2 RS-232 RS422 RS485 Setting / CN_IR IrDA Setting
JVLCD
Jumper: JAT Type: onboard 3-pin header
JAT Mode
1-2 AT Mode 2-3 ATX Mode
Default setting: 2-3
JRTC
JAT
1
3
JCSEL1
JCSEL2
-
14-
Page 16
FS-97E User’s Manual
y
2.4 <CPU and Memory Setup>
2.4.1 <CPU Setup>
The board comes with the socket 478 for Intel Core 2 Duo socket-P processor only it supports new generation with 667/800/1066 MHz of front side bus. Please follow the instruction to install the CPU properly.
Unlock wa
1. Use the flat-type screw drive to unlock the CPU socket
2. Follow the pin direction to install the processor on the socket
Check point
4. Socket P has 478 pins, but is not
3. Lock the socket
pin-compatible with Socket P CPU.
-
15-
Socket-P CPU Check point
Page 17
FS-97E User’s Manual
2.4.2 <Memory Setup>
The board provides two 204-pin DDR3 SO-DIMM to support 800/1066 MHz memory module up to 8GB. Non-ECC, unbuffered memory is supported only, dual channel technology is enabled automatically for higher performance.
SO-DIMM2
-
16-
Page 18
FS-97E User’s Manual
2.5 <CMOS Setup>
The board’s data of CMOS can be setting in BIOS. If the board refuses to boot due to inappropriate CMOS settings, here is how to proceed to clear (reset) the CMOS to its default values.
Jumper: JRTC Type: Onboard 3-pin jump
JRTC Mode
1-2 Clear CMOS 2-3 Normal Operation
Default setting: 2-3
JRTC
1
3
-
17-
Page 19
FS-97E User’s Manual
2.6 <Serial ATA Interface>
Based on Intel ICH9M, the board provides three Serial ATAII interfaces with up to 300MB/s of transfer rate and support AHCI. Based on VIA VT-6421, the board provides two Serial ATAI interfaces with up to 150MB/s of transfer rate and support RAID 0,1.
SATA1/2 support RAID 0,1
SATA 3/4/5 support AHCI
-
18-
Page 20
FS-97E User’s Manual
2.7 <Ethernet Interface>
The board integrates with two Intel 82574L Gigabit Ethernet controllers. The Intel Gigabit Ethernet supports triple speed of 10/100/1000Base-T, with IEEE802.3 compliance and Wake-On-LAN supported.
RJ45_1/2
-
19-
Page 21
FS-97E User’s Manual
2.8 <Onboard Display Interface>
Based on Intel GM45 chipset with built-in GMA (Graphic Media Accelerator) 4500MHD graphics, the board provides, 40-pin LVDS interface with 5-pin LCD backlight inverter connector. The board provides dual display function with clone mode and extended desktop mode for VGA, LVDS, HDTV and DVI.
2.8.1 <Analog VGA Interface>
Please connect your CRT or LCD monitor with DB15 male connector to the onboard DB15 female connector on rear I/O port.
-
20-
CRT
Page 22
FS-97E User’s Manual
2.8.2 <Digital Display>
The board provides one 40-pin LVDS connector up to two mode for 18/24-bit single/dual channel panels, supports up to 1920 x 1200 (UXGA) resolution, with LCD backlight inverter connector and jumper for panel voltage setting.
JVLCD
6
5
40
39
CN_LVDS
2
1
2 1
1 5
CN_INV
Effective patterns of connection: 1-2 / 3-4 / 5-6
2
4
6
1
3
Warning: others cause damages
-
21-
5
Page 23
FS-97E User’s Manual
Connector: CN_INV Connector: JVLCD Type: 5-pin LVDS Power Header Type: 6-pin Power select Header Connector model: JST B5B-XH-A
Pin Description
1 +12V 2 Reserved (Note) 3 GND 4 GND 5 ENABKL
Note: Reserved for MB internal test
Please treat it as NC.
Connector: CN_LVDS Type: onboard 40-pin connector for LVDS connector Connector model: HIROSE DF13-40DP-1.25V
Pin Signal Pin Signal
2 LCDVCC 1 LCDVCC 4 GND 3 GND 6 ATX0- 5 BTX0-
8 ATX0+ 7 BTX0+ 10 GND 9 GND 12 ATX1- 11 BTX1­14 ATX1+ 13 BTX1+ 16 GND 15 GND 18 ATX2- 17 BTX2­20 ATX2+ 19 BTX2+ 22 GND 21 GND 24 ACLK- 23 BTX3­26 ACLK+ 25 BTX3+ 28 GND 27 GND 30 ATX3- 29 BCLK­32 ATX3+ 31 BCLK+ 34 GND 33 GND 36 DDCPCLK 35 N/C 38 DDCPDATA 37 N/C 40 N/C 39 N/C
Pin Description
1-2 LCDVCC (3.3V) 3-4 LCDVCC (5V) 5-6 LCDVCC (12V)
Default: 1-2
22-
-
Page 24
FS-97E User’s Manual
To setup the LCD, you need the component below:
1. A panel with LVDS interfaces.
2. An inverter for panel’s backlight power.
3. A LCD cable and an inverter cable.
For the cables, please follow the pin assignment of the connector to make a cable, because every panel has its own pin assignment, so we do not provide a standard cable; please find a local cable manufacture to make cables.
LCD Installation Guide:
1. Preparing the FS-97E, LCD panel and the backlight inverter.
2. Please check the datasheet of the panel to see the voltage of the panel, and set the jumper JVLCD to +12V or +5V or +3.3V.
3. You would need a LVDS type cable.
Panel side
For sample illustrator only
4. To connect all of the devices well.
-
23-
Board side
Page 25
FS-97E User’s Manual
After setup the devices well, you need to select the LCD type in the BIOS. The panel type mapping is list below:
BIOS panel type selection form (BIOS Version:1.0)
18-bit Single channel 24-bit Dual channel
NO. Output format NO. Output format
1 640 x 480 11 1280 x 768 2 800 x 480 12 1280 x 1024 3 800 x 600 13 1600 x 1200 4 1024 x 768 14 1920 x 1080 5 1280 x 800 15 1920 x 1200
18-bit Dual channel
6 1280 x 768
24-bit Single channel 7 1024 x 768 8 1280 x 768 9 1280 x 800
10 1366 x 768
24-
-
Page 26
FS-97E User’s Manual
2.8.3 <HDTV Interface>
The board provides an HDTV interface with Intel GM45, supports Composite, S-Video and Component with PAL and NTSC of TV system, and display (clone or extended desktop) function with VGA, LVDS, DVI.
2
Connector: CN_HDTV Connector type: 10-pin header HDTV connector (pitch = 2.54mm)
Pin Number Assignment Pin Number Assignment
1 GND 2 DACB_L 3 DACC_L 4 GND 5 GND 6 N/C 7 DACA_L 8 GND 9 N/C 10 N/C
10
9
1
CN_HDTV
-
25-
Page 27
FS-97E User’s Manual
2.8.4 <DVI Interface >
The board also comes with a DVI interface with Chrontel CH7318C for digital video interface. Connector: CN_DVI Connector type: 26-pin header connector (pitch = 2.00mm)
Pin Number Assignment Pin Number Assignment
1 TX1+ 2 TX1­3 Ground 4 Ground 5 TXC+ 6 TXC­7 Ground 8 PVDD
9 N/C 10 N/C 11 TX2+ 12 TX2­13 Ground 14 Ground 15 TX0+ 16 TX0­17 N/C 18 HPDET 19 DDCDATA 20 DDCCLK 21 GND 22 N/C 23 N/C 24 N/C 25 N/C 26 N/C
2
1
CN_DVI
26
25
-
26-
Page 28
FS-97E User’s Manual
2.9 <Integrated Audio Interface>
The board integrates onboard audio interface with REALTEK ALC888 codec, with Intel next generation of audio standard as High Definition Audio, it offers more sound and other advantages than former HD audio compliance. The main specifications of ALC888 are:
High-performance DACs with 97dB SNR (A-Weighting),
Te n DAC channels support 16/20/24-bit PCM format for 2 sound playback, plus 2 channels of independent stere o sound o utput (mu ltiple stre am ing) through the front panel output
High-quality analog differential CD input
Meets performance requirements for Microsoft WLP 3.0 Premium desktop and mobile PCs
The board provides 2 channels audio speaker out and Mic-In ports for front I/O panel through cable.
-
27-
Page 29
FS-97E User’s Manual
4
4
Connector: CN_AUDIO
Type: 10-pin (2 x 5) 2.54mm-pitch header
Pin Description Pin Description
1 MIC2_L 2 Ground 3 MIC2_R 4 VCC 5 FP_OUT_R 6 MIC2_JD 7 SENSE_B 8 N/C 9 FP_OUT_L 10 LINE2_JD
1
Connector: CD_IN
Type: 4-pin header (pitch = 2.54mm)
Pin Description
1 CD – Left 2 Ground 3 Ground 4 CD – Right
2
1
10
9
12
10
9
CN_AUDIO
1
CD_IN
28-
-
Page 30
FS-97E User’s Manual
2.10 <GPIO Interface>
The board provides a programmable 8-bit digital I/O interface; you can use this general purpose I/O port for system control like POS or KIOSK.
Connector: CN_DIO Type: 12-pin (6 x 2) 2.0mm-pitch header
Pin Description Pin Description
1 Ground 2 Ground 3 GP10 4 GP14 5 GP11 6 GP15
7 GP12 8 GP16 9 GP13 10 GP17 11 VCC 12 +12V
2
1
12
11
2
1
CN_DIO
12
11
-
29-
Page 31
FS-97E User’s Manual
2.11 <Power and Fan Installation>
The board comes with a 4-pin AT power connector for powering the board, three fan connectors for Northbridge, CPU and system. The board also provides a 3-pin ATX function connector. You can just connect the two power connectors without any backplane to work.
2.11.1 <Power connectors>
Connector: DC_IN Type: 4-pin P-type connector for +5V/+12V input
Pin Description Pin Description Pin Description Pin Description
1 +12V 2 Ground 3 Ground 4 +5V
Connector: CN_PS Type: 3-pin ATX function connector
Pin Description Pin Description Pin Description
1 5V Standby 2 Ground 3 Power On
2.11.2 <Fan Connectors>
Connector: CPUFAN Type: 4-pin fan wafer connector
Pin Description Pin Description
1 Ground 2 +12V 3 Fan Speed Detection 4 Fan Control
Connector: SYSFAN Type: 3-pin fan wafer connector
Pin Description Pin Description Pin Description
1 Ground 2 +12V 3 Fan Speed Detection
-
30-
Page 32
FS-97E User’s Manual
4
3
1 4
CPUFAN
1
DC_IN
1
CN_PS
SYSFAN
1
-
31-
Page 33
FS-97E User’s Manual
2.11.3 <ATX Power Mode>
PS_ON cable
A TX Power
32-
-
Page 34
FS-97E User’s Manual
J
2.12 <Switch and Indicator>
The JFRNT provides front control panel of the board, such as power button, reset and beeper, etc. Please check well before you connecting the cables on the chassis.
Connector: JFRNT Type: onboard 14-pin (2 x 7) 2.54-pitch header
Function Signal PIN Signal Function
IDE LED
Reset
Power
Button
HDLED+ 1 2 PWRLED+
Power
HDLED- 3 4 N/C
LED
Reset+ 5 6 PWRLED-
Reset- 7 8 SPK+
N/C 9 10 N/C
Speaker
PWRBT- 11 12 N/C
PWRBT+ 13 14 SPK-
2
FRNT
14
1
13
-
33-
Page 35
FS-97E User’s Manual
Chapter 3 <System Setup>
3.1 <OS installation Guide>
In this card, the functions IDE, CF and SATA1/2 (RAID 0,1) are driven by VIA VT-6421.To activate and to use these features, users must install drivers when installing OS.
To take windows XP installation as an example, please DO the following steps:
1. Please insert VT-6421 floppy driver disk.
2. Boot the system with windows XP installation CD to start to install OS.
3. When you see the botton message, said “P ress F6 if you need to install a third party SCSI or RAID driver,” please DO Press F6. (Refer to photo A.)
4. After the system finishes loading all necessary drivers, here comes with a screen message to ask you press “S” to specify additional device to load VT-6421 drivers. (Refer to photo B.)
5. Please choose the option of VT-6421 XP driver. (Refer to photo C.)
6. Please press “ENTER” to continue installing OS.
IDE & CF & SA TA1/2 built-in with VT -6421
Photo A. Photo B. Photo C.
-
34-
Page 36
FS-97E User’s Manual
3.2 <Audio Configuration>
The board integrates Intel® ICH9M with REALTEK® ALC888 codec. It can support 2 channels sound under system configuration. Please follow the steps below to setup your sound system.
1. Install REALTEK HD Audio driver.
2. Lunch the control panel and Sound Effect Manager.
3. Select Speaker Configuration
4. Select the sound mode to meet your speaker system.
-
35-
Page 37
FS-97E User’s Manual
3.3 <Video Memory Setup>
Based on Intel® GM45 chipset with GMA (Graphic Media Accelerator) 4500MHD, the board supports Intel® DVMT (Dynamic Video Memory Technolog y) 4.0, which would allow the video memory to be allocated up to 1024MB. To support DVMT, you need to install the Intel GMA 4500MHD Driver with supported OS.
BIOS Setup:
Total GFX Memory Size:
This item can let you select a static amount of page-locked graphics memory which will be allocated during driver initialization. Once you select the memory amount, it will be no longer available for system memory.
DVMT Mode: This item can let you select graphics memory
-
36-
Page 38
FS-97E User’s Manual
r
3.4 <Display Properties Setting>
Based on Intel GM45 GMCH with GMA 4500MHD (Graphic Media Accelerator), the board supports two DACs for display device as different resolution and color bit. Please install the Intel Graphic Driver before you starting setup display devices.
1. Click right button on the desktop to lunch display properties
2. Click Advanced button for more specificity setup.
Click Graphics Properties... fo advanced setup
37-
-
Page 39
FS-97E User’s Manual
3. This setup options can let you define each device settings.
Click Monitor to setup the CRT monitor for Colors, Resolution and Refresh Rate
Click Intel(R) Dual Display
Clone to setup the dual
display mode as same screen
38-
-
Page 40
FS-97E User’s Manual
Chapter 4 <BIOS Setup>
The motherboard uses the Award BIOS for the system configuration. The Award BIOS in the single board computer is a customized version of the industrial standard BIOS for IBM PC AT-compatible computers. It supports Intel x86 and compatible CPU architecture based processors and computers. The BIOS provides critical low-level support for the system central processing, memory and I/O sub-systems.
The BIOS setup program of the single board computer let the customers modify the basic configuration setting. The settings are stored in a dedicated battery-backed memory, NVRAM, retains the information when the power is turned off. If the battery runs out of the power, then the settings of BIOS will come back to the default setting.
The BIOS section of the manual is subject to change without notice and is provided here for reference purpose only. The settings and configurations of the BIOS are current at the time of print, and therefore they may not be exactly the same as that displayed on your screen.
To activate CMOS Setup program, press <DEL> key immediat ely after you turn on the system. The following message “Press DEL to enter SETUP” should appear in the lower left hand corner of your screen. When you enter the CMOS Setup Utility, the Main Menu will be displayed as Figure 4-1. You can use arrow keys to select your function, press <Enter> key to accept the selection and enter the sub-menu.
Figure 4-1 CMOS Setup Utility Main Screen
-
39-
Page 41
FS-97E User’s Manual
(This page is left for blank)
40-
-
Page 42
FS-97E User’s Manual
Appendix A <I/O Port Pin Assignment>
A.1 <Serial ATA Port>
Connector: SATA1/2/3/4/5 Type: 7-pin wafer connector
1 2 3 4 5 6 7
GND SATA_TXP0 SATA_TXN0 GND SATA_RXN0 SATA_RXP0 GND
7 1
A.2 <IrDA Port>
Connector: CN_IR Type: 5-pin header for SIR Ports
Pin Description
1 VCC 2 N/C 3 IRRX 4 Ground 5 IRTX
1
5
JCSEL1 must jump to “IrDA”
41-
-
Page 43
FS-97E User’s Manual
A.3 <SMBUS Port>
Connector: CN_ SMBUS Type: 5-pin header for SMBUS Ports
Pin Description
1 V5S 2 N/C 3 SMBDATA 4 SMBCLK 5 Ground
1
5
A.4 <Serial Port 2>
Connector: CN_COM2 Type: 9-pin box header
Pin Description Pin Description
1 DCD/422TX-/485-/+5V 2 RX/422TX+/485+ 3 TX/422RX+ 4 DTR/422RX­5 Ground 6 DSR 7 RTS 8 CTS 9 RI /+12V
1
9 10
2
-42-
Page 44
FS-97E User’s Manual
A.5 < RS-232, RS-422, RS-485 & IrDA >
Function JCSEL1 JCSEL2
8 2
2
12
IrDA
1
7
2
8
1
2
11 12
RS-422
11
12
11
12
RS-485
1
1
2
7
2
8
7
8
1
2
1
2
RS-232
1
7
1
11
JCSEL1
1
7
-43-
JCSEL2
2
2
1
8
12
11
Page 45
FS-97E User’s Manual
A.6 <Parallel Port>
Connector: LPT Type: 26-Pin box header
Pin Description Pin Description
1 -PSTB 14 AFD­2 PRO0 15 ERR­3 PRO1 16 INT­4 PRO2 17 SLIN­5 PRO3 18 Ground 6 PRO4 19 Ground 7 PRO5 20 Ground 8 PRO6 21 Ground 9 PRO7 22 Ground 10 ACK- 23 Ground 11 BUSY 24 Ground 12 PE 25 Ground 13 SLCT 26 N/C
A.7 <LAN Port>
Connector: RJ45_1/2 Type: RJ45 connector with LED
14 26
1
13
1
8
Pin 1 2 3 4 5 6 7 8
Description MI0+ MI0- MI1+ MI2+ MI2- MI1- MI3+ MI3-
A.8 <USB Interface>
Connector: CN_USB 1/2/3/4 Type: 10-pin (5 x 2) header for dual USB Ports
Pin Description Pin Description
1 VCC 2 VCC 3 Data0- 4 Data1­5 Data0+ 6 Data1+ 7 Ground 8 Ground 9 Ground 10 N/C
2
1
-44-
10
9
Page 46
FS-97E User’s Manual
2
A.9 <DVI Port>
Connector: CN_DVI Type: onboard 26-pin connector for DVI connector
125
Pin Description Pin Description
1 TDC1+ 2 TDC1­3 GND 4 GND 5 TLC+ 6 TLC­7 GND 8 V5S
9 N/C 10 N/C 11 TDC2+ 12 TDC2­13 GND 14 GND 15 TDC0+ 16 TDC0­17 N/C 18 HPD 19 DVI_DA 20 DVI_SL 21 GND 22 BR 23 BG 24 BB 25 5HSYNC 26 5VSYNC
26
A.10 <PS/2 Keyboard & Mouse Port>
Connector: PS2 Type: 6-pin Mini-DIN connector on bracket
Pin 1 2 3 4 5 6
Description KBD MSD Ground VCC KBC MSC
Note: The PS/2 connector supports standard PS/2 keyboard directly or both PS/2 keyboard and mouse through the PS/2 Y-type cable.
-45-
1
2
3
5 6
4
Page 47
FS-97E User’s Manual
Appendix B <Flash BIOS>
B.1 <Flash Tool>
The board is based on Award BIOS and can be updated easily by the BIOS auto flash tool. You can download the tool online at the address below:
http://www.phoenix.com/en/home/ http://www.commell.com.tw/Support/Support_SBC.htm
File name of the tool is “awdflash.exe”, it’s the utility that can write the data into the BIOS flash ship and update the BIOS.
B.2 <Flash BIOS Procedure>
1. Please make a bootable floppy disk.
2. Get the last .bin files you want to update and copy it into the disk.
3. Copy awardflash.exe to the disk.
4. Power on the system and flash the BIOS. (Example: C:/ awdflash XXX.bin)
5. Restart the system.
Any question about the BIOS re-flash please contact your distributors or visit the web-site at below:
ftp://ftp.commell.com.tw/COMMELL/support/AWDFLASH.rar
46-
-
Page 48
FS-97E User’s Manual
Appendix C <System Resources>
C.1 <Direct Memory Access (DMA)>
C.2 <Direct Memory Access (IRQ)>
47-
-
Page 49
FS-97E User’s Manual
C.3 <Input /Output (IO)>
48-
-
Page 50
FS-97E User’s Manual
49-
-
Page 51
FS-97E User’s Manual
C.4 <Memory Address Map>
50-
-
Page 52
FS-97E User’s Manual
Appendix D <Programming GPIO’s>
The GPIO’ s can be programmed with the MSDOS debug program using simple IN/ OUT commands. The following lines show an example how to do this.
GPIO0…..GPIO7 bit0……bit7
-o 2E 87
-o 2E 87 ;Enter configuration
-o 2E 07
-o 2F 09 ;Enable GPIO’s function
-o 2E 30
-o 2F 02 ;Enable GPIO’s configuration
-o 2E F0
-o 2F xx ;Set GPIO’s as input/output; set ‘1’ for input,’0’for output
-o 2E F1
-o 2F xx ;If set GPIO’s as output, in this register its value can be set
Optional:
-o 2E F2
-o 2F xx ; Data inversion register; ‘1’ inverts the current value of the bits,’0’ leaves them as they are
-o 2E 30
-o 2F 01 ; Active GPIO’s
For further information, please refer to Winbond W83627DHG datasheet.
51-
-
Page 53
FS-97E User’s Manual
Appendix E <Programming Watchdog Timer>
The watchdog timer makes the system auto-reset while it stops to work for a period. The integrated watchdog timer can be setup as system reset mode by program.
Time-out Value Range
- 1 to 255
- Second or Minute
Program Sample
Watchdog timer setup as system reset with 5 second of timeout
2E, 87 2E, 87 2E, 07 2F, 08 Logical Device 8 2E, 30 2F, 01 Activate 2E, F5 2F, 00 Set as Second* 2E, F6 2F, 05 Set as 5
* Minute: bit 3 = 1; Second: bit 3 = 0
You can select Timer setting in the BIOS, after setting the time options, the system will reset according to the period of your selection.
52-
-
Page 54
FS-97E User’s Manual
Contact Information
Any advice or comment about our products and service, or anything we can help you please don’t hesitate to contact with us. We will do our best to support you for your products, project a business.
Taiwan Commate Computer Inc.
Address
TEL +886-2-26963909 FAX +886-2-26963911 Website E-Mail
19F, No. 94, Sec. 1, Shin Tai Wu Rd., Shi Chih Taipei Hsien, Taiwan
TUhttp://www.commell.com.twUT TUinfo@commell.com.twUT (General Information)
TUtech@commell.com.twUT (Technical Support)
Commell is a brand name of Taiwan Commate Computer Inc.
53-
-
Loading...