COMMELL FS-97B User Manual
FS-97B
Full-size PICMG CPU Card User’s Manual
Edition: 1.1
2009/05/04
FS-97B User’s Manual
Copyright
Copyright 2007. All rights reserved. This document is copyrighted and all rights are
reserved. The information in this document is subject to change without prior notice to make
improvements to the products.
This document contains proprietary information and protect ed by copyright. No part of this
document may be reproduced, copied, or translated in any form or any means without prior
written permission of the manufacturer.
All trademarks and/or registered trademarks contains in this document are propert y of their
respective owners.
Disclaimer
The company shall not be liable for any incidental or consequenti al dam ages res ultin g from
the performance or use of this product.
The company does not issue a warranty of any kind, e xpress or implied, including without
limitation implied warranties of merchantability or fitness for a particular purpose.
The company has the right to revise the manual or include changes in th e specifications of
the product described within it at any time without notice and without obligation to notify any
person of such revision or changes.
Trademark
All trademarks are the property of their respective holders.
Any questions please visit our website at TUhttp://www.commell.com.twUT.
2
FS-97B User’s Manual
Packing List
Please check package component before you use our products.
Hardware:
FS-97B Full-Size cpu card x 1
Cable Kit:
Floppy flat cable x 1
4-pin to 3-pin ATX cable x 1
DB25 & DB9 cable x 1
USB cable x 2
PS/2 Keyboard & Mouse Cable x 1
COM Port Cable x 1
(FS-97BDG2/BXG2 Only)
Audio Port Cable x 1
SATA Cable x 6
DVI module with bracket x 1
(FS-97BDG/BDG2 Only)
Other Accessories:
Divers CD (including User’s Manual) x 1
3
FS-97B User’s Manual
Index
Chapter1 <Introduction>
1.1 <Product Overview> .............................................................................................7
1.2 <Product Specification>........................................................................................8
1.3 <Block Diagram> ................................................................................................10
1.4 <Mechanical Drawing > ......................................................................................11
............................................................7
Chapter 2 <Hardware Setup>.................................................12
2.1 <Connector Location>......................................................................................... 12
2.2 <Jumper Reference>..........................................................................................13
2.3 <Connector Reference>......................................................................................14
2.3.1 <Internal Connectors> ..............................................................14
2.3.2 <External Connectors> .............................................................14
2.4 <CPU and Memory Setup>.................................................................................15
2.4.1 <CPU installation>...................................................................15
2.4.2 <Memory installation>..............................................................16
2.5 <CMOS Setup>...................................................................................................17
2.6 <Serial ATA installation>......................................................................................18
2.7 <LAN Interface>..................................................................................................19
2.8 <Onboard Display Interface>..............................................................................20
2.8.1 <Analog Display>....................................................................20
2.8.2 <LVDS Display FS-97BXG＆XG2 Only >...................................21
2.8.3 <DVI Display FS-97BDG/ DG2 Only >.......................................25
2.9 <Audio Installation> ............................................................................................26
2.11 <GPIO interface>..............................................................................................28
2.12 <USB2.0 Interface> ..........................................................................................29
2.13 <Power and Fan Installation> ...........................................................................30
2.14 <Serial Port>.....................................................................................................32
2.15 <Switch and Indicator> .....................................................................................34
4
FS-97B User’s Manual
Chapter 3 <System Configuration>.......................................36
3.1 <SATA configuration>..........................................................................................36
3.2 <SATA RAID Configuration>...............................................................................37
3.3 <Audio Configuration> ........................................................................................41
3.4 <Video Memory Setup>......................................................................................42
3.5 <Display Properties Setting>...............................................................................44
Chapter 4 <BIOS Setup>.........................................................46
Appendix A <I/O Port Pin Assignment>................................48
A.1 <Serial ATA Port>................................................................................................48
A.2 <IrDA Port>.........................................................................................................48
A.3 <VGA Port>........................................................................................................49
A.4 <LAN Port>.........................................................................................................49
A.5 <Floppy Port>.....................................................................................................50
A.6 <Parallel Port>....................................................................................................50
Appedix B <System Resources>...........................................51
B1.<I/O Port Address Map>......................................................................................51
B2.<Memory Address Map> .....................................................................................53
B3.<System IRQ Resources>...................................................................................54
Appedix C <Flash BIOS>.........................................................55
C.1 <BIOS Auto Flash Tool> .....................................................................................55
C.2 <Flash Method> .................................................................................................55
Appendix D <Programming GPIO’s>....................................56
Appendix E <Watch Dog timer Setting >..............................57
Contact Information...................................................................58
5
FS-97B User’s Manual
(This Page is Left for Blank)
6
FS-97B User’s Manual Introduction
Chapter1 <Introduction>
1.1 <Product Overview>
FS-97B is the Full-size single board computer with last Intel desktop technology with
PICMG form factor. Based on Intel® Q965 and ICH8DO, the board integrates a new Core 2
Duo /Quad processor 775-pin socket, DDR2 memory socket, Intel® Graphic Media
Accelerator 3000 technology, Serial ATA II with RAID function for a powerful desktop
system.
Intel
® LGA775 processor
The Intel® Core 2 Duo /Quad processor now comes with a new form factor with 775-pin
PLGA package, for 533/800/1066MHz front-side-bus, 4MB L2 cache, and for 65nm
manufacturing technology, the PLGA processor without pin header on solder side can make
user installing the processor on the socket easier.
Intel
® Q965 and ICH8DO chipset
The Intel Q965 integrates DDR2 533/667/800MHz for memory, and Graphic Media
Accelerator (GMA) 3000 technology for new graphic engine. It can provid e up to 256MB of
frame buffer when you install over 1GB of system memory. The ICH8DO integrates with up
to 6 USB2.0 interfaces , and serial ATA II interface with RAID function.
Flexible Extension Interface
The board provides one mini-PCI socket.
Product Overview 7
FS-97B User’s Manual Introduction
1.2 <Product Specification>
General Specification
Form Factor Full-size PICMG CPU card
CPU Intel® Core 2 Duo /Quad/ Pentium 4 / Pentium D / Celeron D
processor with LGA775 socket
Package type: PLGA 775
Front side bus: 533/800/1066MT/s (133/200/266MHz x 4)
Intel® Hyper-Threading Technology and Dual/Quad core
supported
Memory 2 x 240-pin DDR2 533/667/800MHz SDRAM up to 4GB
Unbufferred, none-ECC memory supported only
Chipset Intel® Q965 (Northbridge) and ICH8DO (Southbridge)
BIOS Phoenix-Award v6.00PG 8Mb SPI flash BIOS
Green Function Power saving mode includes doze, standby and suspend modes.
ACPI version 1.0 and APM version 1.2 compliant
Watchdog Timer System reset programmable watchdog timer with 1 ~ 255
sec./min. of timeout value
Real Time Clock Intel® ICH8DO built-in RTC with lithium battery
Serial ATAII Intel® ICH8DO integrates 6 Serial ATA II interface
RAID 0, 1,5,10 Intel Matrix Storage Technology supported
Multi-I/O Port
Chipset Intel® 82801HDO( ICH8DO) with Winbond® W83627DHG
controller
Serial Port One RS-232 and one RS232/422/485 serial ports
USB Port Six Hi-Speed USB 2.0 ports with 480Mbps of transfer rate
Parallel Port One internal bi-direction parallel port with SPP/ECP/EPP mode
Floppy Port One internal Floppy port
IrDA Port One IrDA compliant Infrared interface supports SIR
K/B & Mouse External PS/2 keyboard and mouse port on bracket
GPIO One 12-pin Digital I/O connector with 8-bit programmable I/O
interface
Smart Fan One CPU fan connector for fan speed controllable
VGA Display Interface
Chipset Intel® Q965 GMA3000 (Graphic Memory Controller Hub)
Frame Buffer Up to 256MB shared with system memory
Display Type CRT, LCD monitor with analog display
Onboard 18/24-bit dual channel LVDS interface (FS-97BXG/
XG2 Only) Onboard DVI interface (FS-97BDG / DG2 Only)
Connector External DB15 female connector on bracket
Onboard 40-pin LVDS connector(FS-97BXG/ XG2 Only)
Onboard 26-pin DVI Connector (FS-97BDG / DG2 Only)
Product Specification 8
FS-97B User’s Manual Introduction
Ethernet Interface
Controller One or two Intel 82573L Gigabit Ethernet controller
Type Triple speed 10/100/1000Base-T
Auto-switching Fast Ethernet
Full duplex, IEEE802.3U compliant
Connector Two External RJ45 connectors with LED on bracket
Audio Interface
Chipset Intel® ICH8DO with Realtek ALC260 HD Audio
Intel High Definition Audio compliance
Interface 2 channels sound output
Connector Internal 10-pin header for line-in/-out, MIC-in, 4-pin header for
CD-IN
Expansive Interface
Mini PCI One Mini-PCI socket TYPE III A (32-bit, 33MHz)
Power supply: +3.3V, +5V, 3VSB
Power and Environment
Power
+5V, +12 DC input & 5V
Requirement
SB
Requirement
Dimension 338 (L) x 122 (H) mm
Temperature Operating within 0 ~ 60℃ (32 ~ 140℉)
Storage within -20 ~ 85℃ (-4 ~ 185℉)
Ordering Code
FS-97BDG Onboard VGA, Gigabit LAN, Mini-PCI, 6 x SATA, HD Audio, 1 X
IrDA, DVI, 3 x USB, Serial port, LPT, GPIO, FDD
FS-97BXG Onboard VGA, Gigabit LAN, Mini-PCI, 6 x SATA, HD Audio, 1 X
IrDA, LVDS, 3 x USB, Serial port, LPT, GPIO, FDD
FS-97BDG2 Onboard VGA, 2 x Gigabit LAN, Mini-PCI, 6 x SATA, HD Audio,
1 X IrDA, DVI, 3 x USB, 2 x Serial port, LPT, GPIO, FDD
FS-97BXG2 Onboard VGA, 2 x Gigabit LAN, Mini-PCI, 6 x SATA, HD Audio,
1 X IrDA, LVDS, 3 x USB, 2 x Serial port, LPT, GPIO, FDD
The specifications may be different as the actual production.
For further product information please visit the website at
TUhttp://www.commell.com.twUT
Product Specification 9
FS-97B User’s Manual Introduction
r
1.3 <Block Diagram>
Intel Core 2 Quad with 775 pin PLGA processo
DVI
LVDS
6 x USB2.0 ports
HD Audio
2 x Serial ports
1 x Parallel port
CH7307
CH7308
W83627THG
Intel Q965
ICH8DO
SPI
2 x 240-pin DDR2
533/667/800MHz
up to 4GB
6 x Serial ATAII ports
Intel 82573L
2 x GLAN
Mini-PCI slot
1 x Floppy port
8-bit GPIO
1 x IrDA
BIOS
Block Diagram 10
FS-97B User’s Manual Introduction
1.4 <Mechanical Drawing >
Mechanical Drawing 11
FS-97B User’s Manual Hardware Setup
V
Chapter 2 <Hardware Setup>
2.1 <Connector Location>
CN_12
DC_IN
NBFAN
DDRII_A/B
CN_PS
FDD
CN_USB1~3
CN_LPT
SYSFAN
CN_AUDIO
CDIN
S_ATA1~6
MINIPCI
CN_DIO
CN_ATKB
CN_IR
JFRNT
CN_INV
PS2 RJ45_2 RJ45_1 CRT
PS2 COM1 RJ45_1 CRT
CN_LVDS
CN_DVI
CN_COM1/2CPUFAN
Connector Location 12
FS-97B User’s Manual Hardware Setup
2.2 <Jumper Reference>
Jumper Function
JRTC CMOS Operating/Clear Setting
JVLCD Panel Voltage Setting (FS-97BXG & XG2 Only)
JVLCD
JRTC
Jumper Reference 13
FS-97B User’s Manual Hardware Setup
2.3 <Connector Reference>
2.3.1 <Internal Connectors>
Connector Function Remark
CPU LGA775 CPU socket
DDRIIA/B 240 -pin DDR2 SDRAM DIMM socket
FDD 34-pin floppy connector
CN_LPT 13 x 2-pin LPT connector
S_ATAII1/2/3/4/5/6 7-pin Serial ATA II connector
CN_12V 8-pin +12V additional power supply connector
CN_AUDIO 5 x 2-pin audio connector
CDIN 4-pin CD-ROM audio input connector
CN_PS 3-pin ATX function connector
DC_IN 4-pin power supply connector
CN_DIO 6 x 2-pin digital I/O connector
CN_USB1/2/3 10-pin USB connector
CPUFAN 4-pin CPU cooler fan connector
SYSFAN 3-pin system cooler fan connector
NBFAN 3-pin Northbridge cooler fan connector
CN_IR 5-pin IrDA connector
CN_ATKB 5-pin AT keyboard connector
CN_INV 5-pin LCD inverter connector FS-97BXG
CN_LVDS 20 x 2-pin LVDS connector FS-97BXG
JFRNT 14-pin front panel switch/indicator connector
Mini-PCI 1 x 124-pin Mini-PCI socket
CN_DVI 26-Pin connector FS-97BDG
CN_COM1/2 5 x 2-pin com connector
2.3.2 <External Connectors>
Connector Function Remark
CRT DB15 VGA connector
RJ45_1/2 One RJ45 LAN connector
PS2 PS/2 keyboard and mouse connector
Connector Reference 14
FS-97B User’s Manual Hardware Setup
f
2.4 <CPU and Memory Setup>
2.4.1 <CPU installation>
FS-97B has a LGA775 CPU socket onboard; please check following steps to install the
processor properly.
Attention If FS-97B need RMA please Keep CPU socket cover on the CPU Socket.
Warring If CPU Socket internal Pin damage We could not provide warranty.
Intel® Core 2 Duo /Quad processor
Package type: 775 pin PLGA
L2 Cache: 4 MB
FSB: 533/800/1066MHz (266MHz x 4)
Manufacturing: 65nm, 90nm
Intel Hyper Threading Technology
1. Lift this bar
and Core 2 Duo /Quad supported
Check point
3. Place the CPU on the top o
2. Uncover this plate
4. Lock this bar
Notice: Please place the CPU on the pins tenderlyto avoid bending the pins
the pins
3. Cover this plate
CPU installation 15
FS-97B User’s Manual Hardware Setup
2.4.2 <Memory installation>
FS-97B has two 240-pin DDR2 DIMM support up to 4GB of memory capacity. The memory
frequency supports 533/667/800MHz . Only Non-ECC memory is supported.
DDRIIA/B
112-pin128-pin
Please check the pin number to match the socket side well
before installing memory module.
Memory Installation 16
FS-97B User’s Manual Hardware Setup
2.5 <CMOS Setup>
The board’s data of CMOS can be setting in BIOS. If the board refuses to boot due to
inappropriate CMOS settings, here is how to proceed to clear (reset) the CMOS to its
default values.
Jumper: JRTC
Type: Onboard 3-pin jumper
JRTC Mode
1-2 Clear CMOS
2-3 Normal Operation
Default setting
1 3
JRTC
CMOS Setup 17
FS-97B User’s Manual Hardware Setup
2.6 <Serial ATA installation>
FS-97B has six Serial ATA II interfaces with RAID function, the transfer rate of the Serial
ATA II can be up to 300MB/s. Please go to http://www.serialata.org/
ATA technology information. Based on Intel® ICH8DO, it supports Intel® Matrix Storage
Technology with combination of RAID 0,1,5 and 10. The main features of RAID on
ICH8DO are listed below:
1. Supports for up to RAID volumes on a single, two-hard drive RAID array.
2. Supports for two, two-hard drive RAID arrays on any of six Serial ATA ports.
3. Supports for Serial ATA ATAPI devices.
4. Supports for RAID spares and automatic rebuild.
5. Supports on RAID arrays, including NCQ and native hot plug.
For more information please visit Intel’s official website.
For more about the system setup for Serial ATA, please check the chapter of SATA
configuration.
for more about Serial
S_ATA1~6
Serial ATA Installation 18
Loading...