Commell FS-977PRO User Manual

Page 1

FS-977PRO

User’s Manual

Edition 1.0

Copyright© 2002, 2003. All rights reserved. This document is copyrighted and all rights are reserved. The information in this document is subject to change without prior notice to make improvements to the products. This document contains proprietary information and protected by copyright. No part of this document may be reproduced, copied, or translated in any form or any means without prior written permission of the manufacturer. All trademarks and/or registered trademarks contains in this document are property of their respective owners.

Disclaimer

Taiwan Commate Computer Inc. shall not be liable for any incidental or consequential damages resulting from the performance or use of this product. Taiwan Commate Computer Inc. does not issue a warranty of any kind, express or implied, including without limitation implied warranties of merchantability or fitness for a particular purpose. The company has the right to revise the manual or include changes in the specifications of the product described within it at any time without notice and without obligation to notify any person of such revision or changes.

Trademark

All trademarks are the property of their respective holders.

Any question please visit our website at

http://www.commell.com.tw.

FS-977PRO User’s Manual

Page 2

Packing List

Hardware

FS-977 Single Board Computer........................................ X 1

Cable Kit

34-pin FDD Cable ............................................................. X 1

TV-out Cable with bracket................................................. X 1

1 x COM / 1 x LPT Port DB9 / DB25 Cable (VL only)........ X 1

2 x COM Port DB9 Cable (VL2 only)................................. X 1

1 x LPT Port DB25 Cable (VL2 only) ................................ X 1

Dual-USB Port Cable with Bracket.................................... X 2

PS/2 Keyboard and Mouse Cable..................................... X 1

40-pin UltraATA/100 IDE Cable........................................ X 2

Audio Cable ...................................................................... X 1

3-pin to 4-pin ATX cable.................................................... X 1

Printed Matter and Software

User’s Manual................................................................... X 1

Driver CD.......................................................................... X 1

FS-977PRO User’s Manual

Page 3

Table of Content

Chapter 1. Introduction ......................................................................5

1.1 Product Overview..................................................................................5

1.2 Specification..........................................................................................6

1.3 Component Placement .........................................................................9

1.4 Block Diagram.....................................................................................10

Chapter 2. Hardware Setup.................................................................11

2.1 Jumper and Connector Location ................................................................. 11

2.1.1 Jumper Reference.............................................................................12

2.1.2 Connector Reference........................................................................13

2.2 CPU and DRAM Setting......................................................................14

2.3 CMOS Setting.....................................................................................14

2.4 Watchdog T imer Setting......................................................................15

2.5 Embedded Solid State Disk ................................................................16

2.6 Power and Fan Connector..................................................................17

2.7 VGA Interface .....................................................................................18

2.7.1 Standard Analog VGA Interface.......................................................18

2.7.2 Digital VGA Interface......................................................................... 19

2.7.3 TV-out Interface.................................................................................21

2.8 Ethernet Interface ...............................................................................22

2.9 Audio Interface....................................................................................23

2.10 Switch and Indicator............................................................................24

Chapter 3. BIOS Setup......................................................................25

Chapter 4. Driver Installation...........................................................27

FS-977PRO User’s Manual

Page 4

Appendix. A I/O Port Pin Assignment.............................................29

A.1 IDE Port.............................................................................................. 29

A.2 Floppy Port......................................................................................... 30

A.3 Parallel Port........................................................................................ 31

A.4 Serial Port........................................................................................... 32

A.4.1 Onboard RS-232C Serial Port ..........................................................32

A.4.2 On Bracket RS-232C Serial Port......................................................32

A.5 USB Port ............................................................................................ 33

A.6 IrDA Port............................................................................................. 33

A.7 VGA Port............................................................................................ 34

A.8 LAN Port............................................................................................. 34

A.9 AT Keyboard Port ...............................................................................35

A.10 PS/2 Keyboard and Mouse Port......................................................... 35

Appendix B.Flash the BIOS................................................................37

B.1 BIOS Auto Flash T ool .........................................................................37

B.2 Flash Method...................................................................................... 37

Appendix C. System Resource........................................................39

C.1 I/O Port Address Map......................................................................... 39

C.2 Memory Address Map......................................................................... 40

C.3 IRQ and DMA Resource..................................................................... 41

Contact Information.............................................................................44

FS-977PRO User’s Manual

Page 5

Chapter 1. Introduction

1.1 Product Overview

The FS-977PRO SBC (Single Board Computer) is an all-in-one industrial full-size PICMG (PCI/ISA)-bus CPU card based on Intel Socket 478 Pentium 4 architecture. With Intel Brookdale-GV chipset, Intel 845GV GMCH and ICH4, FS-977PRO offers the value computing solution including Intel NetBurst micro-architecture, 533/400 MHz of FSB, 2GB DDR SDRAM, Intel Extreme Graphics with 266 MHz VGA core, 256-bit 3D engine, Intel Dynamic Video Memory up to 64 MBytes, LVDS interface, TV-out, one Intel PRO/100+ LAN and one Intel PRO/1000+ LAN, Hi-Speed USB 2.0 and M-systems DiskOnChip solid state flash disk interfaces.

Based on the Intel's long term supply chipset in the EIA (Embedded Intel Architecture) division’s product roadmap, FS-977PRO should be the ideal solution for the industrial applied computing platform with high computing capacity, cost effect and long life cycle. With Intel’s latest technology, the FS-977PRO should be the leading edge of computing capacity for the advanced industrial computing platform with the features as below.

Intel Hyper-Threading Technology

The FS-977PRO supports Intel Hyper-Threading Technology to offer the better computing capacity for the industrial applied computing application. Based on Intel's latest technology, "the Intel Pentium 4 Processor with Hyper-Threading technology allows software programs to "see" two processors and work more efficiently. Improves performance and system responsiveness in today's multitasking environments by enabling the processor to execute instruction threads in parallel."

Powerful Computing Capacity

With Intel’s latest CPU technology, FS-977PRO supports Intel Socket 478 Pentium 4 CPU up to 3.06 GHz at 533 MHz of FSB and low cost Intel Socket 478 Celeron CPU up to 2.4 GHz at 400 MHz of FSB. The FS-977PRO also provides two GBytes of DDR200/266/333 of system memory capacity.

Hi-Speed USB 2.0 Interface: Intel ICH4 built-in Hi-Speed USB 2.0 controller offers the Hi-Speed USB 2.0 interface with up to 480 Mbps of data transfer bandwidth with the USB bootable setting in the BIOS.

FS-977PRO User’s Manual

Page 6

1.2 Specification

General Specification

Form Factor Full-size PICMG-bus CPU Card / Slot PC

PICMG version 1.0 (Rev. 2.0), PCI version 2.0 compliant

CPU Intel Socket 478 Pentium 4 / Celeron CPU

at 400/533 MHz FSB (100/133MHz x 4) Intel 0.13-/0.18-micron Northwood / Willamette CPU

Support Intel Hyper-Threading Technology

Memory Two 184-pin DIMM sockets support up to 2 GBytes

DDR200/266/333 SDRAM. (No ECC/register DIMM support)

Chipset Intel 82845GV GMCH and 82801DB ICH4 BIOS Phoenix-Award 2Mb PnP flash BIOS

Green Function Power saving mode supported in BIOS with DOZE,

STANDBY and SUSPEND modes. ACPI version 1.0 and APM version 1.2 compliant

Watchdog Timer Generates NMI or system reset programmable watchdog

timer with 1 to 255 sec./min. of time out value

Real Time Clock Intel ICH4 built-in RTC with onboard lithium battery Enhanced IDE PCI enhanced IDE interface supports dual ports up to 4

ATAPI devices with UltraATA/100 supported Jumper selectable Vcc power output on IDE2 for power cable free DOM (DiskOnModule) flash disk

ISA High Drive ISA 64mA high Drive capacity with TI 245 buffer on both

of ISA address and data bus

Solid State Disk Interface

Flash Type M-systems DiskOnChip 2000, DiskOnChip Millennium,

IDE Pro and DiskOnModule (DOM) solid state flash disk

Package 32-pin DIP JEDEC (DiskOnChip)

40-pin IDE port (DOC IDE Pro, DiskOnModule)

Capacity 1GB of DiskOnChip and 512 MB of DiskOnModule

FS-977PRO User’s Manual

Page 7

Multi-I/O Port

Chipset Intel 82801DB ICH4 and Winbond W83627HF-AW LPC

super-I/O controller

Serial Port Two RS-232 serial ports. Both with 16C550 compatible

UART and 16 bytes FIFO.

USB 2.0 Port Four Hi-Speed USB 2.0 ports with Intel ICH4

Support 480 Mbps of data transfer rate

Parallel Port One bi-direction parallel port with SPP/ECP/EPP mode Floppy Port One floppy port supports up to two FDD IrDA Port One IrDA compliant Infrared interface supports SIR K/B & Mouse PS/2 keyboard and mouse ports, AT keyboard port

VGA Display Interface

Chipset

Intel 845GV GMCH built-in Intel Extreme Graphics with 266 MHz VGA core

Video Memory Intel Dynamic Video Memory with auto detect video

memory up to 64 MBytes shared with system memory

Display Type CRT and LCD monitor

LVDS Color LCD

LCD Interface 24-bit single/dual channel LVDS interface Connector

External DB15 female connector on bracket for CRT Dual Internal 20-pin header for LVDS interface

Internal 16-pin header for analog VGA display

TV-out Interface

Chipset Intel 845GV GMCH built-in Intel Extreme Graphics with

Chrontel CH7017A-T TV-out encoder TV Mode Support both of NTSC and PAL mode Connector Internal 8-pin header for TV-out interface

FS-977PRO User’s Manual

Page 8

Ethernet Interface

Chipset One Intel PRO/100+ LAN interface and one Intel

PRO/1000+ LAN interface Primary LAN (LAN1): Intel ICH4 with Intel 82562ET PHY Secondary LAN (LAN2): PCI Intel 82540EM

Type LAN1:10Base-T / 100Base-TX,

auto-switching Fast Ethernet Full duplex, IEEE802.3U compliant LAN2: 10Base-T / 100Base-TX/1000Base-T auto-switching Fast Ethernet

Full duplex, IEEE

802.3, 802.3u, 802.3ab compliant

Audio Interface

Chipset

Intel ICH4 built-in AC97 3D audio controller with codec

Interface Line-in, line-out, CD-in, Mic-in

Power and Environment

Power Req. +5V, +12V, -12V DC input from PICMG backplane

Additional +12V on 4-pin connector for Pentium 4 PSU

ATX Function 3-pin ATX interface with 5V standby and power-on Dimension 338 (L) x 122 (H) mm, standard PICMG form factor Temperature Operating within 0 ~ 60oC (32 ~ 140oF)

Storage within -20 ~ 85

C (-4 ~ 185oF)

EMI

Ordering Code

FS-977PROVXL Full-size PICMG Socket 478 Pentium 4 DDR CPU Card

with 533/400 MHz FSB, Intel Extreme Graphics, Intel PRO/100+ LAN , LVDS interface, TV-out, Audio, Hi-Speed USB 2.0, DOC Socket and ISA 64mA High Drive Capacity

FS-977PROVXL2 Same as FS-977PROVL but

with Intel PRO/100+ L AN and Intel PRO/1000+ LAN

FS-977PRO User’s Manual

Page 9

1.3 Component Placement

ITE8888 ISA Bridge

Winbond 83627HF-AW

LPC Su

er-I/O

2 x 184-pin DIMM Sockets

System Memory

2 GB DDR200/266/333

Intel 845GV GMCH

Built-in Intel

Extreme Graphics

mPGA478 CPU Socket

Intel Pentium 4 / Celeron

533/400 MHz FSB

Intel 82801DB ICH4

Built-in Hi-Speed

USB 2.0 Interface

Intel PRO/100+ LAN

Intel PRO/1000+ LAN

with 82540EM

FS-977PRO User’s Manual

Page 10

1.4 Block Diagram

Intel Socket 478 Pentium 4 / Celeron CPU

Intel 0.13-/0.18-micron Northwood / Willamette

Support Intel Hyper-Threading Technology

FSB 400 / 533 MHz 100 / 133 MHz x 4

LVDS

Encoder

LCD

LAN2

Two 184-pin DIMM Sockets up to 2 GBytes DDR SDRAM

UltraATA100 IDE

100 MBps

DDR266 DDR333

ATAPI Device

ISA Bus Interface

Intel 266 Mbps

Intel 845GV

GMCH

CRT

AT Keyboard

PS/2 Mouse Floppy

Serial Device

Parallel Device

LPC

SIO

PS/2 Keyboard

Hi-Speed USB 2.0

480 Mbps

Intel ICH4

PCI Bus Interface

Intel

82540EM

iTE 8888

PCI-ISA

Bridge

PICMG Backplane

LAN1

PHY

Codec

Audio Devices

USB Devices

LVDS

FS-977PRO User’s Manual

Page 11

Chapter 2. Hardware Setup

This chapter contains the information for installation of hardware. The install procedure includes jumper settings, CPU and memory installation, fan, I/O and panel connections.

2.1 Jumper and Connector Location

USB2 USB1 SYSFAN CRT LAN1 LAN2(COM1 for VXL )

FDD

LPT

JIR DOC IDE2 IDE1

JDOM

JRTC

CN_TV JLVDS2 JLVDS1

DIMM2

DIMM1

CPU

JPS

JFRNT

PS2 JATKB JCOM2 JCOM1 JLAN2 JDOC JWDT JAUDIOJ JWOL CDIN CN_INV JVLCD

CPUFAN

ATXREG

FS-977PRO User’s Manual

Page 12

2.1.1 Jumper Reference

Jumper Function Section

JRTC COMS Operate / Clear Setting 2.3 JWDT Watchdog Timer NMI / Reset Setting 2.4 JDOC DiskOnChip SSD Address Setting 2.5 JDOM DiskOnModule SSD Power Setting 2.5 JVLCD Flat Panel’s Voltage Setting 2.7.2 JLAN2 Secondary LAN Enable/Disable Setting 2.8

FS-977PRO User’s Manual

Page 13

2.1.2 Connector Reference

Internal Onboard Connector

Connector Function Remark

CPU MicroPGA478 CPU Socket Standard DIMM1/2 184-pin DIMM Socket Standard IDE1/2 40-pin Primary / Secondary IDE Port Standard FDD 34-pin Floppy Port Standard LPT 26-pin Parallel Port Standard JCOM1/2 10-pin COM1/2 Serial Port Standard USB1/2 10-pin 1st / 2nd (3rd / 4th) USB Port Standard JIR 5-pin SIR IrDA Port Standard DOC 32-pin DIP DiskOnChip Socket Standard JATKB 5-pi n AT Keyboard Connector Standard ATXREG 4-pin Additional +12V Power Connector Standard JPS 3-pin ATX Signal Connector Standard JFRNT 14-pin Switch and Indicator Connector Standard CPUFAN 3-pin +12V CPU Fan Connector Standard SYSFAN 3-pin +12V System Fan Connector Standard JVGA 16-pin Internal VGA Port Standard JAUDIO 10-pin Audio Port Standard CDIN 4-pin CD-in Interface Standard WOL 3-pin Wake-On-LAN Interface Standard JLVDS1 20-p in LVDS interface Standard JLVDS2 20-p in LVDS interface Standard CN_INV 5-pi n Backlight Inverter power connector Standard CN_TV TV-out interface Standard

External Connector on Bracket

Connector Function Remark

VGA DB15 Fema le VGA Connector Standard LAN1 RJ45 LAN1 Connector Standard LAN2 RJ45 LAN2 Connector VXL2 only COM1 DB9 Male COM1 Connector VXL only PS2 6-pin MiniDIN PS/2 Keyboard & Mouse Standard

FS-977PRO User’s Manual

Page 14

FS-977PRO User’s Manual

2.2 CPU and DRAM Sett ing

The board is based on Intel Socket 478 architecture with Intel 845GV chipset, supports Intel Socket 478 Pentium 4 / Celeron CPU at 533/400 MHz FSB.

System memory of this board supports up to 2 GBytes DDR200/266/333 SDRAM on two 184-pin DIMM sockets. Please notices that Intel 845GV GMCH DOESN’T support ECC and register DIMM.

2.3 CMOS Setting

The board’s data of CMOS can be setting in BIOS. If the board refuses to boot due to inappropriate CMOS settings, here is how to proceed to clear (reset) the CMOS to its default values.

Jumper: JRTC Type: onboard 3-pin header

JRTC Mode

1-2 Clear CMOS 2-3 Normal Operation

Default setting

JRTC

Page 15

2.4 Watchdog Timer Setting

The watchdog timer makes the systems auto-reset while it stop to work for a period. The onboard watchdog timer can be setup as system reset or active NMI mode by jumper JWDT.

Jumper: JWDT Type: onboard 3-pin header

JWDT Watchdog Timer

1-2 Active NMI 2-3 Reset

Default setting

JWDT

1 2 3

Program Sample

Watchdog timer setup as system reset with 5 second of timeout 2E, 87

2E, 87 2E, 07 2F, 08 Logical Device 8 2E, 30 Activate 2F, 01 2E, F5 Set as Second* 2F, 00 2E, F6 Set as 5 2F, 05 * Minute: bit 3 = 0; Second: bit 3 = 1

FS-977PRO User’s Manual

Page 16

977PRO User’s Manual

S-

2.5 Embedded Solid State Disk

The board supports both 32-pin M-systems DiskOnChip 20 00 and IDE-ba sed DiskOnChip IDE Pro and DiskOnModule (DOM) embedded flash disk. The onboard 32-pin socket, DOC, supports DiskOnChip 2000 single chip flash disk in 32-pin DIP JEDEC with jumper selectable address on jumper JDOC; onboard 40-pin IDE2 box header supports normal DOM (DiskOnModule) or M-systems DiskOnChip IDE Pro flash disk with jumper selectable +5V Vcc power for cable free applications on jumper JDOM.

123

JDOC

JDOM

DiskOnChip 2000 Address Setting

Jumper: JDOC Type: onboard 3-pin header

JDOC DiskOnChip Address

1-2 D000h 2-3 D800h

Default setting

DOM or DiskOnChip 2000 IDE Pro Power Setting

Jumper: JDOM Type: onboard 2-pin header

JDOM +5V on Pin-20 of IDE2

OFF (Open) Disable ON (Close) Enable

Default setting

Page 17

2.6 Power and Fan Connector

JPS

123

SYSFAN CPUFAN

ATXREG

31 42

Connector: ATXREG Type: 4-pin standard Pentium 4 additional +12V power connector

Pin Description Pin Description 1 Ground 2 Ground

3 +12V 4 +12V

Connector: JPS Type: 3-pin ATX wafer connector

Pin Description Pin Description Pin Description 1 5V_Standby 2 Ground 3 Power_on

Connector: CPUFAN, SYSFAN Type: 3-pin fan wafer connector

Pin Description Pin Description Pin Description 1 Ground 2 +12V 3 Fan Control

FS-977PRO User’s Manual

Page 18

2.7 VGA Interface

2.7.1 Standard Analog VGA Interface

The board is integrated with Intel 845GV GMCH chipset built-in Intel Extreme Graphics with 266 MHz VGA core, 256-bit 3D engine and Intel Dynamic Video Memory up to 64 MBytes shared with system memory. The CRT / analog VGA interface includes one external DB15 female conn ecto r on bracket and one internal 16-pin header on board.

JVGA

8 16

Connector: JVGA Type: 16-pin (2 x 8) 2.54-pitch header

Pin Description Pin Description 1 Red 9 Green

2 Blue 10 N/C 3 Ground 11 Ground 4 Ground 12 Ground 5 N/C 13 Ground 6 N/C 14 Data 7 HSYNC 15 VSYNC 8 Clock 16 N/C

FS-977PRO User’s Manual

Page 19

2.7.2 Digital VGA Interface

The board provides an LVDS Interface, with Intel 845GV GMCH built-in Intel Extreme Graphics with CHRONTEL CH7017A-T encoder.

JLVDS1 JLVDS2

CN_INV

JVLCD

Jumper: JVLCD Type: onboard 3-pin header

JVOLT1 LCD Voltage Setting

1-2 +5V 2-3 +3.3V

Default setting

FS-977PRO User’s Manual

Page 20

LVDS TFT/DSTN LCD Interface

Connector: JLVDS1, Type: onboard 20-pin Hirose DF13-20DP-1. 25V

Pin Signal Pin Signal

1 VCCLCD 2 VCCLCD 3 GND 4 GND 5 A0- 6 A0+ 7 GND 8 A1-

9 A1+ 10 GND 11 A2- 12 A2+ 13 GND 14 CLK115 CLK1+ 16 GND 17 A3- 18 A3+ 19 GND 20 GND

Connector: JLVDS2

Type: onboard 20-pin Hirose DF13-20DP-1. 25V

Pin Signal Pin Signal

1 VCCLCD 2 VCCLCD

3 GND 4 GND

5 A4- 6 A4+

7 GND 8 A5-

9 A5+ 10 GND 11 A6- 12 A6+ 13 GND 14 CLK215 CLK2+ 16 GND 17 A7- 18 A7+ 19 GND 20 GND

LCD Backlight Inverter Power Connector

Connector: CN_INV Type: 5-pin wafer connector

Pin Description 1 +12V

2 Ground 3 Ground 4 Ground 5 ENABKL

FS-977PRO User’s Manual

Page 21

2.7.3 TV-out Interface

The board provides the AV and S-video TV-out Interface at both of PAL and NTSC mode, with Intel 845GV chipset built-in VGA interface and CHRONTEL CH7017A-T encoder.

CN_TV

Connector: CN_TV Type: onboard 8-pin (2 x 4) 2.54-pitch pin header

Pin Description Pin Description 1 Ground 2 TVY

3 TVC 4 Ground 5 Ground 6 N/C 7 TVCVBS 8 Ground

FS-977PRO User’s Manual

Page 22

2.8 Ethernet Interface

The board integrated with one Intel PRO/100+ Fast Ethernet interface at the type of 10Base-T/100Base-TX auto-switching Fast Ethernet with full duplex and IEEE 802.3U compliant, and one Intel PRO/1000+ Fast Ethernet interface at the type of 10Base-T/100Base-TX/1000Base-T auto-switching Fast Ethernet with full duplex and IEEE

802.3, 802.3u, 802.3ab compliant

Both of them connect via RJ45 connectors on bracket. The LAN2 can enable or disable by jumper JLAN. The primary LAN interface is controlled by I ntel ICH2 with Intel 82562ET and setting as LAN1. It provides the same performance as Intel 82559 LAN with the same driver. The secondary LAN interface is controlled by Intel 82540EM chipset and setting as LAN2.

Jumper: JLAN2 Type: onboard 3-pin (1 x 3) 2.54-pitch header

JLAN2 LAN2 Enable / Disable Setting

1-2 Enable 2-3 Disable

Default setting

JLAN2

JWOL

1 2 3

Connector: JWOL Type: onboard 3-pin (1 x 3) wafer connector

Pin 1 2 3 Description +5V Standby Ground WOL

FS-977PRO User’s Manual

Page 23

2.9 Audio Interface

The board integrates with AC97 3D audio i nterface by Intel ICH4 and codec, provides line-in, line-out, Mic-in and CD-in interfaces for industrial applications with audio function.

JAUDIO

CDIN

1 2 3 4

Connector: JAUDIO Type: 10-pin (2 x 5) 2.54-pitch header

Pin Description Pin Description 1 Line – Right 2 Ground

3 Line – Left 4 MIC 5 MIC 6 Ground 7 N/C 8 Line Out – Left 9 Line Out – Right 10 Ground

Connector: CDIN Type: 4-pin header

Pin Description 1 CD – Left

2 Ground 3 Ground 4 CD – Right

FS-977PRO User’s Manual

Page 24

2.10 Switch and Indicator

Connector: JFRNT Type: onboard 14-pin (2 x 7) 2.54-pitch header

Function Signal PIN Signal Function

Vcc (+) 1 2 (+) Vcc

Active 3 4 N/C

Reset 5 6 GND

Power

LED

IDE LED

Reset

GND 7 8 Vcc

N/C 9 10 N/C

PWRBT 11 12 N/C

Power

Button

GND 13

14 SPKIN

Speaker

JFRNT

14 13

FS-977PRO User’s Manual

Page 25

Chapter 3. BIOS Setup

The single board computer uses the Award BIOS for the system configuration. The Award BIOS in the single board computer is a customized version of the industrial standard BIOS for IBM PC AT-compatible computers. It supports Intel x86 and compatible CPU architecture based pr ocessors and com puters. The BIOS provides critical low-level support for the system central processing, memory and I/O sub-systems.

The BIOS setup program of the single board computer let the customers modify the basic configuration setting. The settings are stored in a dedicated battery-backed memory, NVRAM, retains the information when the po wer is turned off. If the battery runs out of the power, then the settings of BIOS will come back to the default setting.

The BIOS section of the manual is subject to change without notice and is provided here for reference purpose only. The settin gs and configurations of the BIOS are current at the time of print, and therefore they may not be exactly the same as that displayed on your screen.

To activate CMOS Setup program, press ＜DEL＞ key immediately after you turn on the system. The following message “Press DEL to enter SETUP” should appear in the lower left hand corner of your screen. When you enter the CMOS Setup Utility, the Main Menu will be displaye d as Figure 3-1. You can use arrow keys to select your function, press ＜Enter＞ key to accept the selection and enter the sub-menu.

Figure 3-1. CMOS Setup Utility Main Screen

Phoenix – Award BIOS CMOS Setup Utility

>Standard CMOS Features >Frequency/Voltage Control >Advanced BIOS Features Load Fail-Safe Defaults >Advanced Chipset Features >Integrated Peripherals

Load Optimized Defaults

Set Supervisor Password >Power Management Setup Set User Password >PnP / PCI Configura tions Save & Exit Setup >PC Health Status Exit Without Saving

Esc : Quit ↑ ↓ → ← : Select Item F10 : Save & Exit Setup

FS-977PRO User’s Manual

Page 26

Notes (This page left blank intentionally)

FS-977PRO User’s Manual

Page 27

Chapter 4. Driver Installation

The driver CD offers auto-run menu. It will detect and select the type of single board computer and helps you install the driv ers automatically.

Install Related Chipset INF Driver

The selection helps you to install the INF of related chipset interface.

Install VGA Driver

The selection helps you to install the driver of onboard VGA interface.

Install LAN Driver

The selection helps you to install the driver of onboard LAN interface.

Install Audio Driver

The selection helps you to install the driver of onboard audio interface.

Install Hi-Speed USB 2.0 Driver

The selection helps you to install the driver of onboard USB 2.0 interface.

Link to < Website > Homepage

The selection helps you to link to the website to find the updated technical documents and download directly.

Browse this CD

The selection helps you to find the drivers in this CD directly.

FS-977PRO User’s Manual

Page 28

Notes (This page left blank intentionally)

FS-977PRO User’s Manual

Page 29

Appendix. A I/O Port Pin Assignment

A.1 IDE Port

2 1

40 39

Connector: IDE1, IDE2 Type: 40-pin (2 x 20) 2.54-pitch box header

Pin Description Pin Description 1 Reset 2 Ground

3 D7 4 D8 5 D6 6 D9 7 D5 8 D10 9 D4 10 D11 11 D3 12 D12 13 D2 14 D13 15 D1 16 D14 17 D0 18 D15 19 Ground 20 N/C (Vcc) * 21 REQ 22 Ground 23 IOW-/STOP 24 Ground 25 IOR-/HDMARDY 26 Ground 27 IORDY/DDMARDY 28 IDESEL 29 DACK- 30 Ground 31 IRQ 32 N/C 33 A1 34 CBLID 35 A0 36 A2 37 CS0 (MASTER CS) 38 CS1 (SLAVE CS) 39 LED ACT- 40 Ground

* Jumper selectable Vcc power on IDE2 port for power cable free DOM (DiskOnModule).

FS-977PRO User’s Manual

Page 30

A.2 Floppy Port

1 2

33 34

Connector: FDD Type: 34-pin (2 x 17) 2.54-pitch header

Pin Description Pin Description 1 Ground 2 REDWC

3 Ground 4 N/C 5 Ground 6 N/C 7 Ground 8 INDEX9 Ground 10 MOTOR ENABLE A11 Ground 12 DRIVER SELECT B13 Ground 14 DRIVER SELECT A15 Ground 16 MOTOR ENABLE B17 Ground 18 DIRECTION19 Ground 20 STEP21 Ground 22 WRITE DATA23 Ground 24 WRITE GATE25 Ground 26 TRACK 027 Ground 28 WRITE PROTECT29 Ground 30 READ DATA31 Ground 32 HEAD SELECT33 Ground 34 DISK CHANGE-

FS-977PRO User’s Manual

Page 31

A.3 Parallel Port

13 26

1 14

Connector: LPT Type: 26-pin (2 x 13) 2.54-pitch box header

Pin Description Pin Description 1 STROBE- 14 AUTO FEED-

2 D0 15 ERROR3 D1 16 INITIALIZE4 D2 17 SELECT INPUT5 D3 18 Ground 6 D4 19 Ground 7 D5 20 Ground 8 D6 21 Ground 9 D7 22 Ground 10 ACKNOWLEDGE- 23 Ground 11 BUSY 24 Ground 12 PAPER EMPTY 25 Ground 13 SELECT+ 26 N/C

FS-977PRO User’s Manual

Page 32

A.4 Serial Port

A.4.1 Onboard RS-232C Serial Port

1 2

Connector: JCOM1, JCOM2 Type: 10-pin (2 x 5) 2.54-pitch header

Pin Description Pin Description 1 DCD 2 RXD

3 TXD 4 DTR 5 Ground 6 DSR 7 RTS 8 CTS 9 RI 10 N/C

5 4 3 2 1

A.4.2 On Bracket RS-232C Serial Port

9 8 7 6

Connector: COM1 (Optional for FS-977VL only) Type: 9-pin D-sub male connector on bracket

Pin Description Pin Description 1 DCD 2 RXD

3 TXD 4 DTR 5 Ground 6 DSR 7 RTS 8 CTS 9 RI

FS-977PRO User’s Manual

Page 33

A.5 USB Port

6 1

10 5

Connector: USB1, USB2 Type: 10-pin (2 x 5) header for dual USB Ports

Pin Description Pin Description 1 Vcc 6 Vcc

2 Data0- 7 Data13 Data0+ 8 Data2+ 4 Ground 9 Ground 5 Ground 10 N/C

A.6 IrDA Port

Connector: JIR Type: 5-pin (1 x 5) 2.54-pitch header for SIR Port

Pin Description 1 Vcc

2 N/C 3 IRRX 4 Ground 5 IRTX

FS-977PRO User’s Manual

Page 34

A.7 VGA Port

Connector: VGA Type: 15-pin D-sub female connector on bracket

Pin Description Pin Description Pin Description 1 RED 6 Ground 11 N/C

2 GREEN 7 Ground 12 VDDAT 3 BLUE 8 Ground 13 HSYNC 4 N/C 9 Vcc 14 VSYNC 5 Ground 10 Ground 15 VDCLK

1 2 3 4 5

11 12 13 14 15

A.8 LAN Port

Connector: LAN1 Type: RJ45 connector with LED on bracket

Pin 1 2 3 4 5 6 7 8 Description TX+ TX- RX+ N/C N/C RX- N/C N/C

Connector: LAN2 (Optional for FS-977PROVXL2) Type: RJ45 connector with LED on bracket

Pin 1 2 3 4 5

Description TRD0+ TRD0- TRD1+ TRD1- NC

Pin 6 7 8 9 10

Description NC TRD2+ TRD2- TRD3+ TRD3-

FS-977PRO User’s Manual

Page 35

A.9 AT Keyboard Port

Connector: JATKB Type: 5-pin box header

Pin 1 2 3 4 5 Description Vcc GND N/C DAT CLK

A.10 PS/2 Keyboard and Mouse Port

5 6

Connector: PS2 Type: 6-pin MiniDIN connector on bracket

Pin 1 2 3 4 5 6 Description KBD MSD Ground N/C KBC MSC

Note: The PS/2 connector supports standard PS/2 keyboard directly or both PS/2 keyboard and mouse through the PS/2 Y-type cable. The cable is the standard on packing list.

FS-977PRO User’s Manual

Page 36

Notes (This page left blank intentionally)

FS-977PRO User’s Manual

Page 37

Appendix B. Flash the BIOS

B.1 BIOS Auto Flash Tool

The board is based on Award BIOS and can be updated easily by the BIOS auto flash tool. You can download the tool online at the address below:

http://www.award.com

http://www.commell.com.tw/Support/Support.htm

File name of the tool is “awdflash.exe”, it’s the utility that can write the data into the BIOS flash ship and update the BIOS.

B.2 Flash Method

1. Get the “.bin” file including the image of new BIOS you want to update.

2. Power on the system and flash the BIOS.

3. Re-star the system.

Any question about the BIOS re-flash please contact your distributors or visit our website at below:

http://www.commell.com.tw/Support/Support.htm

FS-977PRO User’s Manual

Page 38

Notes (This page left blank intentionally)

FS-977PRO User’s Manual

Page 39

Appendix C. System Resource

C.1 I/O Port Address Map

Address Range Device

0060-0060 i8042prt 0064-0064 i8042prt 0170-0177 atapi 01CE-01CF VgaSave 01F0-01F7 atapi 02F8-02FE Serial 0376-0376 atapi 0378-037A Parport 0380-038B VgaSave 03C0-03DF VgaSave 03F0-03F5 Floppy 03F6-03F6 atapi 03F7-03F7 Floppy 03F8-03FE Serial C000-C03F E100B C400-C41D E100E E000-E0EF alcxnt E400-E43F alcxnt

FS-977PRO User’s Manual

Page 40

C.2 Memory Address Map

Device Physical Address Length

x00000000 - x0009FFFF System board extension for PnP BIOS x000A0000 - x000AFFFF Intel(R) 82845G/GV Graphics Controller x000B0000 - x000BFFFF Intel(R) 82845G/GV Graphics Controller x000C0000 - x000CADFF Intel(R) 82845G/GV Graphics Controller x000CAE00 - x000CBFFF Motherboard resources x000F0000 - x000F3FFF Motherboard resources x000F4000 - x000F7FFF Motherboard resources x000F8000 - x000FFFFF Motherboard resources x00100000 - x00FFFFFF System board extension for PnP BIOS xE0000000 - xE7FFFFFF Intel(R) 82845G/GV Graphics Controller xE8000000 - xEBFFFFFF Intel(R) 82845G/GV Processor to I/O Controller 2560 xEC000000 - xEC1FFFFF Intel(R) 82801DB PCI Bridge - 244E xEC100000 - xEC11FFFF Intel(R) GD82540EM PCI Adapter xEC120000 - xEC120FFF Intel(R) PRO/100 VE Network Connection xEC121000 - xEC121FFF Intel(R) GD82540EM PCI Adapter xEC200000 - xEC27FFFF Intel(R) 82845G/GV Graphics Controller xEC280000 - xEC2803FF Intel (R) USB Enhanced Host Controller (ICH4) xEC281000 - xEC2811FF Avance AC97 Audio xEC282000 - xEC2820FF Avance AC97 Audio xFEC00000 - xFEC0FFFF System board extension for PnP BIOS xFEE00000 - xFEE0FFFF System board extension for PnP BIOS xFFB00000 - xFFB7FFFF System board extension for PnP BIOS xFFB80000 - xFFBFFFFF Intel(r) 82802 Firmware Hub Device xFFF00000 - xFFFFFFFF System board extension for PnP BIOS

FS-977PRO User’s Manual

Page 41

C.3 IRQ and DMA Resource

C.3.1 IRQ

IRQ Number Device

0 System timer 1 Standard 101/102-Key or Microsoft Natural Keyboard 2 Programmable interrupt controller 3 Communications Port (COM2) 4 Communications Port (COM1) 5 Intel(R) 82801DB/DBM USB Universal Host Controller - 24C2 5 IRQ Holder for PCI Steering 5 Intel(R) 82845G/GV Graphics Controller 6 Standard Floppy Disk Controller 7 Printer Port (LPT1) 8 System CMOS/real time clock 9 Intel (R) USB Enhanced Host Controller (ICH4) 9 IRQ Holder for PCI Steering 10 Avance AC97 Audio 10 Intel(R) 82801DB/DBM SMBus Controller - 24C3 10 Intel(R) GD82540EM PCI Adapter 10 Intel(R) 82801DB/DBM USB Universal Host Controller - 24C4 10 IRQ Holder for PCI Steering 11 Intel(R) PRO/100 VE Network Connection 11 Intel(R) 82801DB/DBM USB Universal Host Controller - 24C7 11 IRQ Holder for PCI Steering 12 PS/2 Compatible Mouse Port 13 Numeric data processor 14 Primary IDE controller (dual fifo) 14 Intel(R) 82801DB Ultra ATA Stor age Controller - 24CB 15 Secondary IDE controller (dual fifo) 15 Intel(R) 82801DB Ultra ATA Stor age Controller - 24CB

FS-977PRO User’s Manual

Page 42

C.3.2 DMA

Channel Device

0 (free) 1 (free) 2 Standard Floppy Disk Controller 3 (free) 4 Direct Memory Access Controller 5 (free) 6 (free) 7 (free)

FS-977PRO User’s Manual

Page 43

Notes (This page left blank intentionally)

FS-977PRO User’s Manual

Page 44

Contact Information

Any advice or comment about our products and service, or anything we can help you please don’t hesitate to contact with us. We will do our best to support you for your products, projects and business.

COMMELL Industrial Computer Taiwan Commate Computer Inc.

COMMELL

www.commell.com.tw

Your Embedded Applied Computer Partner

Address

8F, No. 94, Sec. 1, Shin Tai Wu Rd., Shi Chih

Taipei Hsien, Taiwan TEL +886-2-26963909 FAX +886-2-26963911 Website

http://www.commell.com.tw

E-mail

info@commell.com.tw (General Information)

tech@commell.com.tw (Technical Support)

Authorized Distributor

FS-977PRO User’s Manual