Taiwan Commate Computer Inc. shall not be liable for any incidental or
consequential damages resulting from the performance or use of this product.
Taiwan Commate Computer Inc. does not issue a warranty of any kind,
express or implied, including without limitation implied warranties of
merchantability or fitness for a particular purpose.
The company has the right to revise the manual or include changes in the
specifications of the product described within it at any time without notice and
without obligation to notify any person of such revision or changes.
Trademark
All trademarks are the property of their respective holders.
Any question please visit our website at http://www.commell.com.tw
.
FS-977 User’s Manual
1
Page 2
Packing List
Hardware
FS-977 Single Board Computer........................................ X 1
Cable Kit
34-pin FDD Cable ............................................................. X 1
40-pin IDE Flat Cable (UltraDMA/33)................................ X 1
1 x COM / 1 x LPT Port DB9 / DB25 Cable (VL only)........ X 1
2 x COM Port DB9 Cable (VL2 only)................................. X 1
1 x LPT Port DB25 Cable (VL2 only) ................................ X 1
Dual-USB Port Cable with Bracket.................................... X 2
PS/2 Keyboard and Mouse Cable..................................... X 1
40-pin UltraATA/100 IDE Cable........................................ X 1
Audio Cable ...................................................................... X 1
3-pin to 4-pin ATX cable.................................................... X 1
Printed Matter and Software
User’s Manual................................................................... X 1
Driver CD.......................................................................... X 1
C.3 System IRQ and DMA Resource.............................................. 39
4
FS-977 User’s Manual
Page 5
Chapter 1. Introduction
1.1 Product Overview
FS-977 SBC (Single Board Computer) is an all-in-one industrial full-size PICMG
(PCI/ISA)-bus CPU card based on Intel mPGA478 Pentium 4 architecture. With Intel
Brookdale-G chipset, FS-977 offers the value solution with Intel NetBurst
micro-architecture, 533/400 MHz of FSB, 2 GB DDR200/266/333 DDR SDRAM,
support Hyper-Threading Technology (Pe ntium 4 processor at 3.06 GHz or higher),
Intel Brookdale-G GMCH built-in advanced 3D SVGA, and dual Intel PRO/100+ LAN
and USB 2.0 high speed I/O interfaces.
Based on Intel's long term supply chipset, FS-977 should be the ideal solution for long
life industrial applied computing platform with high computing capacity and cost effect.
The onboard dual Intel PRO/100+ LAN, M-systems DiskOnChip SSD (Solid State Disk),
and ISA 64mA high drive capacity also make FS-977 be the value Pentium 4 DDR
platform for:
Value Industrial Computing Platform: Intel mPGA478 Pentium 4 / Celeron CPU with
533/400 MHz FSB and 2 GB DDR200/266/333 SDRAM of system memory, FS-977
offers the high-end industrial computing platform with low cost Intel integrated solution.
Onboard Intel GV chipset support Hyper-Threading Technology give PCs a
turbo-charge, delivering the power users and PCs need to multi-task and increase
productivity. The long term support, onboard SSD, dual Intel LAN and ISA 64mA high
drive capacity also make FS-977 be the ideal solution for industrial server and
workstation, CTI (Computer Telephony Integration), VoIP (Voice over IP), and other
high-end applications.
Low Cost Multi-media Solution: Intel Brookdale-G chipset built-in advanced 3D VGA
controller offers the value integration solution for low cost multi-media computing
platform. Such as VoD (video on demand), DVR (Digital Video Recorder), digital video
broadcasting (DVB), streaming, surveillance, compression (MPEG), interaction server,
workstation and terminal appliances.
Redundant Network Reliability: dual Intel PRO/100+ 10/100 Mbps Fast Ethernet
interfaces for high reliability of redundant LAN, or external / internal dual direction
networking applications.
Hi-Speed USB 2.0 Interface: Intel ICH4 built-in USB 2.0 controller let FS-977 offer the
high speed USB 2.0 interface with 480 Mbps of data transfer rate. It makes FS-977 be
the platform to link with high-end USB 2.0 devices including digital camera, USB hard
disk, and other USB 2.0 based peripherals.
FS-977 User’s Manual
5
Page 6
1.2 Specification
General Specification
Form Factor Full-size PICMG-bus CPU Card / Slot PC
PICMG version 1.0 (Rev. 2.0), PCI version 2.0 compliant
CPU Intel mPGA478 Pentium 4, Celeron @ 533/400 MHz FSB
Support Intel Hyper-Threading Technology
Support Northwood / Willamette Pentium 4 / Celeron CPU
Memory 2 GBytes DDR200/266/333 SDRAM on 2 x 184-pin DIMM
sockets. (No ECC/register DIMM support)
Chipset Intel 82845GV GMCH and 82801DB ICH4
BIOS Phoenix-Award 2Mb PnP flash BIOS
Green Function Power saving mode supported in BIOS with DOZE, STANDBY
and SUSPEND modes. ACPI version 1.0 and APM version 1.2
compliant
Watchdog Timer Generates NMI or system reset watchdog timer with 1 to 255
sec. / min. of time out value
Real Time Clock Intel ICH4 built-in RTC with lithium battery
Enhanced IDE PCI enhanced IDE interface supports dual ports up to 4 ATAPI
devices with UltraATA/100 supported
ISA High Drive ISA 64mA high Drive capacity with TI 245 buffer on address and
data bus
Multi-I/O Port
Chipset Intel 82801DB ICH4 and Winbond W83627HF-AW LPC
super-I/O controller
Serial Port
USB Port
Parallel Port
Floppy
IrDA Port
K/B & Mouse PS/2 keyboard and mouse ports, AT keyboard port
6
Two RS-232 serial ports. Both with 16C550 compatible UART
and 16 bytes FIFO
Four USB 2.0 ports with 480 Mbps of data transfer rate
One bi-direction parallel port with SPP/ECP/EPP mode
One floppy port supports up to two FDD
One IrDA compliant Infrared interface supports SIR
FS-977 User’s Manual
Page 7
Solid State Disk Interface
Flash Type M-systems DiskOnChip 2000, DiskOnChip Millennium, IDE Pro
and DiskOnModule (DOM) solid state flash disk
Package
Capacity
VGA Display Interface
Chipset Intel 845GV GMCH built-in 256-bit 3D VGA controller
Video Memory
Display Type
Connector
Ethernet Interface
Chipset Dual Intel PRO/100+ LAN interface
Type
Connector
32-pin DIP JEDEC (DiskOnChip)
40-pin IDE port (IDE Pro, DiskOnModule)
576 MB of DiskOnChip and 512 MB of DiskOnModule
Auto detect dynamic video memory up to 64 MBytes
CRT, LCD monitor and analog display
External DB15 female connector on bracket for CRT
Internal 16-pin header for analog VGA display
Primary LAN (LAN1): Intel ICH4 and Intel 82562ET
Optional secondary LAN (LAN2): Intel 82559ER
10Base-T / 100Base-TX, auto-switching Fast Ethernet
Full duplex, IEEE802.3U compliant
External dual RJ45 with LED on bracket
Audio Interface
Chipset Intel ICH4 built-in AC97 3D audio controller with codec
Interface
Connector
FS-977 User’s Manual
Line-in, line-out, CD-in, Mic-out
10-pin header for line-in, line-out and Mic-out
4-pin header for CD-in
7
Page 8
Power and Environment
Power Req. +5V, +12V, -12V DC input from PICMG backplane
Additional +12V on 4-pin connector for Pentium 4 PSU
ATX Function
Dimension
Temperature
EMI
Ordering Code
FS-977VL Full-size PICMG mPGA478 DDR CPU Card Based on Intel 845GV and
FS-977VL2 Full-size PICMG mPGA478 DDR CPU Card Based on Intel 845GV and
3-pin ATX interface with 5V standby and power-on
338 (L) x 122 (H) mm, standard PICMG form factor
o
Operating within 0 ~ 60
Storage within -20 ~ 85
C (32 ~ 140oF)
o
C (-4 ~ 185oF)
CE/FCC class A certified
ICH4, with 533/400 MHz FSB, Intel VGA, Single Intel PRO/100+ LAN,
Audio, Hi-Speed USB 2.0, DOC Interfaces and ISA 64mA High Drive
Capacity
ICH4, with 533/400 MHz FSB, Intel VGA, Dual Intel PRO/100+ LAN,
Audio, Hi-Speed USB 2.0, DOC Interfaces and ISA 64mA High Drive
Capacity
8
FS-977 User’s Manual
Page 9
1.3 Component Placement
System Memory
2 x 184-pin DIMM Socket
2 GB DDR SDRAM
Intel 845GV GMCH
Built-in Intel Extreme
Graphics VGA Core
DiskOnChip
Socket
mPGA478 CPU Socket
Intel Pentium 4 / Celeron
533/400 MHz FSB
FS-977 User’s Manual
Intel 82801DB ICH4
Built-in USB 2.0 Port
AC97 3D Audio
Dual Intel PRO/100+ LAN
Intel ICH4 with 82562ET
and Intel 82559ER
9
Page 10
Notes (This page left blank intentionally)
10
FS-977 User’s Manual
Page 11
VGA
A
Chapter 2. Hardware Setup
This chapter contains the information for installation of hardware. The install
procedure includes jumper settings, CPU and memory installation, fan, I/O
and panel connections.
CPU MicroPGA478 478 CPU Socket
DIMM1/2 184-pin DIMM Socket
IDE1/2 40-pin Primary / Secondary IDE Port
FDD 34-pin FDD Port
LPT 26-pin Parallel Port
JCOM1/2 10-pin COM1/2 Serial Port
USB1/2 10-pin 1st / 2nd (3rd / 4th) USB Port
JIR 5-pin SIR IrDA Port
DOC 32-pin DIP DiskOnChip Socket
JATKB 5-pin AT Keyboard Connector
ATXREG 4-pin Additional +12V Power Connector
JPS 3-pin ATX Signal Connector
JFRNT 14-pin Switch and Indicator Connector
CPUFAN 3-pin +12V CPU Fan Connector
SYSFAN 3-pin +12V System Fan Connector
JVGA 16-pin Internal VGA Port
JAUDIO 10-pin Audio Port
CDIN 4-pin CD-in Interface
WOL 3-pin Wake-On-LAN Interface
External Connector on Bracket
Connector Function
VGA DB15 Female VGA Connector
LAN1 RJ45 LAN1 Connector
LAN2 RJ45 LAN2 Connector VL2 only
PS2 6-pin MiniDIN PS/2 Keyboard & Mouse
COM1 DB9 Male serial port connector VL only
FS-977 User’s Manual
13
Page 14
2.2 CPU and DRAM Setting
The board is based on Intel Socket 478 architecture, supports Intel mPGA478
Pentium 4 / Celeron CPU at 533/400 MHz FSB. The FS-977 is based on Intel
845GV GMCH, supports 533 and 400 MHz FSB.
System memory of this board supports up to 2 GB DDR200/266/333 SDRAM on 2
184-pin DIMM sockets. Please notices that Intel 845GV GMCH doesn’t support
ECC and register DIMM.
2.3 CMOS Setting
The board’s data of CMOS can be setting in BIOS. If the board refuses to boot due
to inappropriate CMOS settings, here is how to proceed to clear (reset) the CMOS to
its default values.
Jumper: JRTC
Type: onboard 3-pin header
JRTC Mode
1-2 Clear CMOS
2-3 Normal Operation
Default setting
JRTC
1
2
3
14
FS-977 User’s Manual
Page 15
2.4 Watchdog Timer Setting
The watchdog timer makes the systems auto-reset while it stop to work for a period.
The onboard watchdog timer can be setup as system reset or active NMI mode by
jumper JWDT.
Jumper: JWDT
Type: onboard 3-pin header
JWDT Watchdog Timer
1-2 Active NMI
2-3 Reset
Default setting
Program Sample
JWDT
1
2
3
Watchdog timer setup as system reset with 5 second of timeout
2E, 87
2E, 87
2E, 07
2F, 08 Logical Device 8
2E, 30 Activate
2F, 01
2E, F5 Set as Second*
2F, 00
2E, F6 Set as 5
2F, 05
* Minute: bit 3 = 0; Second: bit 3 = 1
FS-977 User’s Manual
15
Page 16
2.5 Embedded Solid State Disk
The board supports both 32-pin M-systems DiskOnChip 2000 and IDE-based
DiskOnChip IDE Pro and DiskOnModule (DOM) embedded flash disk. The onboard
32-pin socket, DOC, supports DiskOnChip 2000 single chip flash disk in 32-pin DIP
JEDEC with jumper selectable address on jumper JDOC; onboard 40-pin IDE2 box
header supports normal DOM (DiskOnModule) or M-systems DiskOnChip IDE Pro flash
disk with jumper selectable +5V Vcc power for cable free applications on jumper JDOM.
DiskOnChip 2000 Address Setting
Jumper: JDOC
Type: onboard 3-pin header
JDOC DiskOnChip Address
1-2 D000h
2-3 D800h
Default setting
DOM or DiskOnChip 2000 IDE Pro Power Setting
Jumper: JDOM
Type: onboard 2-pin header
JDOM +5V on Pin-20 of IDE2
OFF Disable
ON Enable
Default setting
16
JDOM
12
JDOC
123
FS-977 User’s Manual
Page 17
2.6 Power and Fan Connector
ATXREG
31
42
Connector: ATXREG
Type: 4-pin Standard Pentium 4 Additional +12V Power Connector
Connector: JPS
Type: 3-pin ATX Function Connector
Connector: CPUFAN, SYSFAN
Type: 3-pin Fan Power Wafer Connector
JPS
CPUFAN
1
3
Pin Description Pin Description
1 Ground 2 Ground
3 +12V 4 +12V
Pin Description Pin Description PinDescription
1 5V Standby 2 Ground 3 Power On
Pin Description Pin Description Pin Description
1 Ground 2 +12V 3 Fan Control
123
SYSFAN
123
FS-977 User’s Manual
17
Page 18
2.7 VGA Interface
The board is integrated with Intel 845GV GMCH built-in Intel Extreme Graphics with
266 MHz VGA core and Intel Dynamic Video Memory up to 64 MBytes shared with
system memory. The CRT / analog VGA interface includes one external DB15
female connector on bracket and one internal 16-pin header on board.
The board integrated with dual Intel PRO/100+ Fast Ethernet interfaces at the type of
10Base-T/100Base-TX auto-switching Fast Ethernet with full duplex and IEEE 802.3U
compliant. Both of them connect via RJ45 connectors on bracket. The LAN2 can enable
or disable by jumper JLAN.
The primary LAN interface is controlled by Intel ICH4 with Intel 82562ET and setting as
LAN1. It provides the same performance as Intel 82559 LAN with the same driver. The
secondary LAN interface is controlled by Intel 82559ER chipset and setting as LAN2.
The board integrates with AC97 3D audio interface by Intel ICH4 and codec, provides
line-in, line-out, Mic-in and CD-in interfaces for industrial applications with audio
function.
Connector: JAUDIO
Type: 10-pin header
Pin Description Pin Description
1 Line – Right 2 Ground
3 Line – Left 4 MIC
5 MIC 6 Ground
7 N/C 8 Line Out – Left
9 Line Out – Right 10 Ground
Connector: CDIN
Type: 4-pin header
Pin Description
1 CD – Left
2 Ground
3 Ground
4 CD – Right
CDIN
JAUDIO
2
1
2
3
4
10
9
20
FS-977 User’s Manual
Page 21
14 13
2.10 Switch and Indicator
Connector: JFRNT
Type: onboard 14-pin header
Function Signal PIN Signal Function
JFRNT
2
IDE LED
Reset
Power
Button
FS-977 User’s Manual
Vcc (+) 1 2 (+) Vcc
Active 3 4 N/C
Reset 5 6 GND
GND 7 8 Vcc
PWRBT 1112N/C
GND 13
Power
LED
N/C 9 10 N/C
Speaker
14SPKIN
21
Page 22
Notes (This page left blank intentionally)
22
FS-977 User’s Manual
Page 23
Chapter 3. BIOS Setup
The single board computer uses the Award BIOS for the system configuration. The
Award BIOS in the single board computer is a customized version of the industrial
standard BIOS for IBM PC AT-compatible computers. It supports Intel x86 and
compatible CPU architecture based processors and computers. The BIOS provides
critical low-level support for the system central processing, memory and I/O
sub-systems.
The BIOS setup program of the single board computer let the customers modify the
basic configuration setting. The settings are stored in a dedicated battery-backed
memory, NVRAM, retains the information when the power is turned off. If the battery
runs out of the power, then the settings of BIOS will come back to the default setting.
The BIOS section of the manual is subject to change without notice and is provided
here for reference purpose only. The settings and configurations of the BIOS are
current at the time of print, and therefore they may not be exactly the same as that
displayed on your screen.
To activate CMOS Setup program, press <DEL> key immediately after you turn on
the system. The following message “Press DEL to enter SETUP” should appear in the
lower left hand corner of your screen. When you enter the CMOS Setup Utility, the Main
Menu will be displayed as Figure 3-1. You can use arrow keys to select your function,
press <Enter> key to accept the selection and enter the sub-menu.
Figure 3-1. CMOS Setup Utility Main Screen
Phoenix – Award BIOS CMOS Setup Utility
>Standard CMOS Features >Frequency/Voltage Control
>Advanced BIOS Features Load Fail-Safe Defaults
>Advanced Chipset Features
>Integrated Peripherals
>Power Management Setup Set User Password
>PnP / PCI Configurations Save & Exit Setup
>PC Health Status Exit Without Saving
Note: The PS/2 connector supports standard PS/2 keyboard directly or both PS/2
keyboard and mouse through the PS/2 Y-type cable. The cable is the standard on
packing list.
3
1
5
6
2
4
FS-977 User’s Manual
33
Page 34
Notes (This page left blank intentionally)
34
FS-977 User’s Manual
Page 35
Appendix B. Flash the BIOS
B.1 BIOS Auto Flash Tool
The board is based on Award BIOS and can be updated easily by the BIOS auto flash
tool. You can download the tool online at the address below:
http://www.award.com
File name of the tool is “awdflash.exe”, it’s the utility that can write the data into the
BIOS flash ship and update the BIOS.
B.2 Flash Method
1. Get the “.bin” file including the image of new BIOS you want to update.
0 System timer
1 Standard 101/102-Key or Microsoft Natural Keyboard
2 Programmable interrupt controller
3 Communications Port (COM2)
4 Communications Port (COM1)
5 Intel(R) 82801DB/DBM USB Universal Host Controller - 24C2
5 IRQ Holder for PCI Steering
5 Intel(R) 82845G/GL Graphics Controller
6 Standard Floppy Disk Controller
7 Printer Port (LPT1)
8 System CMOS/real time clock
9 Intel (R) USB Enhanced Host Controller (ICH4)
9 IRQ Holder for PCI Steering
10 Avance AC97 Audio
10 Intel(R) 82801DB/DBM SMBus Controller - 24C3
10 Intel(R) GD82559ER PCI Adapter
10 Intel(R) 82801DB/DBM USB Universal Host Controller - 24C4
10 IRQ Holder for PCI Steering
11 Intel(R) PRO/100 VE Network Connection
11 Intel(R) 82801DB/DBM USB Universal Host Controller - 24C7
11 IRQ Holder for PCI Steering
12 PS/2 Compatible Mouse Port
13 Numeric data processor
14 Primary IDE controller (dual fifo)
14 Intel(R) 82801DB Ultra ATA Storage Controller - 24CB
15 Secondary IDE controller (dual fifo)
15 Intel(R) 82801DB Ultra ATA Storage Controller - 24CB
FS-977 User’s Manual
39
Page 40
C.3.2 DMA
Channel Device
0 (free)
1 (free)
2 Standard Floppy Disk Controller
3 (free)
4 Direct Memory Access Controller
5 (free)
6 (free)
7 (free)
40
FS-977 User’s Manual
Page 41
Notes (This page left blank intentionally)
FS-977 User’s Manual
41
Page 42
Contact Information
Any advice or comment about our products and service, or anything we can help you
please don’t hesitate to contact with us. We will do our best to support you for your products,
projects and business.
COMMELL Industrial Computer
Taiwan Commate Computer Inc.
COMMELL
Your Embedded Applied Computer Partner
Address
TEL +886-2-26963909
FAX +886-2-26963911
Website http://www.commell.com.tw
E-mail info@commell.com.tw
Authorized Distributor
8F, No. 94, Sec. 1, Shin Tai Wu Rd., Shi Chih
Taipei Hsien, Taiwan
tech@commell.com.tw (Technical Support)
www.commell.com.tw
(General Information)
42
FS-977 User’s Manual
Loading...
+ hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.