USER MANUAL
T65
www.commax.com
Thank you for purchasing COMMAX products.
Please carefully read this User’s Guide (in particular, precautions for safety) before using a product and
follow instructions to use a product exactly.
The company is not responsible for any safety accidents caused by abnormal operation of the product.
1.Getting Started
2.Understanding
Device
3.Operating Menu
Keep out of direct sunlight and heat radiation sources.
Shall not be exposed to dripping or splashing and no objects filled with liquids,
such as vases, shall be placed on the products.
When cleaning, do not use liquid solvent or wet cloth. Wipe with soft cloth.
Never disassemble or modify this device in any way.
(Identery is not liable for problems caused by unauthorized
modification or attempted repair)
Cautions
Before using this device, read and follow all instructions for safety.
COMMAX Access Control Solutions
Do not install this device near by TV, monitor or magnetic interference.
If the product fails to operate normally, contact the authorized dealer
or service senter.
Cautions
Before using this device, read and follow all instructions for safety.
COMMAX Access Control Solutions
T65
Cable
Includid Items
COMMAX Access Control Solutions
LED
Light on for system status.
Fingerprint sensor
Used to register or identity
the user.
Function Key
Speaker
Color TFT LCD
Displays time, device
status, user list and UI
for operation.
Key button for
operation.
Connector
For cable connection.
Parts and Their Functions
COMMAX Access Control Solutions
W:165mm
H:115mm
W:149.8mm
H:92.8mm
49mm
Front View Bracket Bracket
Side View
Dimensions
This system comes with the following comeponents.
COMMAX Access Control Solutions
You have to register fingerprint in proper way to enhance
recognition rate.
Recommended to use finger which has no damage.
Recommended to register more than two fingerprint in case.
Proper way Improper way.
Fingerprint Registration
Place the finger on the sensor as seen in below in the proper way. Place the entire area of your finger firmly to the sensor.
COMMAX Access Control Solutions
CARD ID(PIN) FD(Finger Print)
T65 supports various type of access mode : Combination of Fingerprint, Card and ID(PIN)
Verification mode can be setup in verification mode (Settings>Basic>Verification Mode)
Vertfication Mode
COMMAX Access Control Solutions
Function Key is usually used for Time & Attendance.
The admin is able to setup a certain definition to a function key in the program
(F1 = Sing in) The admin is able to find out the users attendance records.
ID Authentication Scheme F1~F4 + 0~9
CARD Authentication Scheme F1~F4 + 0~9
1. Press Function Key (F1~F4) only or press numbers after Function Key .
2. Present the card to enter.
FD Authentication Scheme F1~F4 + Fingerprint
1. Press Function Key (F1~F4) only or Press numbers after Function Key .
2. Place Finger Print to enter.
1. Press Function Key (F1~F4) only or Press numbers after Function Key .
2. Input ID used to enter.
Functions Key
COMMAX Access Control Solutions
USER
SETTING
USB MEMORY
SYSTEM INFO
TEST
1.Enroll 2.Delete 3.Set Temp ID
1.Basic 2.Advanced 3.AC Setting 4.Communication 5.Schedule 6.Log Setting
1.Download General Log 2.Download All General Log 3.Download Management Log
4.Download All Management Log 5.Download User Info 6.Upload User Info
7.Upgrade Firmware
1.Memory 2.Device Info 3.Advanced
1.Test All 2.Test Memory 3.Test LCD 4.Test Sound (AUTO) 5.Test Sound (MANUAL)
6.Test Sensor 7.Test Keyboard 8.Test RTC 9.Test Case Status 10.Test Card Reader
T65 System Directory on Key
COMMAX Access Control Solutions
SETTING 1.Basic 2.Advanced 3.AC Setting 4.Communication 5.Schedule 6.Log Setting
Basic
1.Time
2.Date
3.Date Format
4.Language
5.Use Busytone detection
6. Set Phone Numbers
Advanced
1.Vertification Mode
2.ID Mask
3.Use Tamer Alram
4.Use Touch Sensor
5.Celibrate Senseor
6.Restore Factory Settings
7.Clear General Log
8.Clear Management Log
9.Clear Enroll Date
AC Settings
1.Define Timezone
2.User Timezone
3.Lock Type
4.Lock Door Release Time
5.Door Open Warning
6.Re-access Count
7.Re-access Limit Time
8.Wiegand Format
9.Anti-Passback
T65 System Tree Structure
COMMAX Access Control Solutions
SETTING 1.Basic 2.Advanced 3.AC Setting 4.Communication 5.Schedule 6.Log Setting
Communication
1.Device ID
2.Baudrate
3.TCP/IP Settings
-DHCP
-IP Antipass
-Subnet Mask
-Default Gateway
-Port
-Mac Address
4.Communication Password
Schedule
1.Set Tmode
2.Ring Settings
3.Auto Door
4.Auto Funckey
5.None-Relat Funckey
6.Day Light
7.Holiday
8.Funckey Alarm
9.Idle Settings
Log Setting
1.Management Log Warning
2.General Log Warning
T65 System Tree Structure
COMMAX Access Control Solutions
1.Getting Started
2.Understanding
Device
3.Operating Menu
DISPLAYS
These displays are primary screens.
Verification Mode Date and Time User Menu
User Enroll Menu Settings Menu
COMMAX Access Control Solutions
Displays
Move Forward
Move Backward
To previous menu
Home Screen
Select the Menu
F1
F2
*
#
F4
F1
F2
Menu Navigation Buttons
COMMAX Access Control Solutions
Default condition and admin is not registered.
> 1 2 3 4 > > Menu Screen
F1
F2
*
#
1.Press Button.
2.After “1 2 3 4”, Press Button
3.Succeed to access system menu
4.Move between menus using or button
*
#
Access To The System Menu 1
COMMAX Access Control Solutions
1.Getting Started
2.Understanding
Device
3.Operating Menu
Admin is registered already.
F1
F2
*
#
*
> Admin ID > > Verify Fingerprint or CD > Main menu
1. Press Button.
2. Press Registered admin ID and
3. Verify fingerprint or CD of the above ID
4. Succeed to access system menu.
5. Move between menus using or button.
Press Button at the bottom left corner to return
home Screen.
*
*
Access To The System Menu 2
Only when admin is registered. Refer to “Admin Registration part” for admin registration.
When admin ID is incorrect, access to the system menu is denied. When admin ID is not registered anyone can be access to system menu.
So it is highly recommended to register admin More than one. Unless stated otherwise instructions in this manual stars from system menu.
COMMAX Access Control Solutions
When ADMIN is not registered
F1
*
#
*
> 1234 > > User > Enroll
1. Press button
2. After “ 1 2 3 4 ” , press button (Access to the system menu)
3. Select “ User ” and press button
4. Select “ Enroll ” and press button
5. Input password(USER ID) and set up the privilege;
User or Admin.
( After User ID, press and set the privilege using the and button )
6. Register fingerprints and/or card
( Refer to p. 16, Menu Navigation Buttons )
#
#
#
#
F1
Register
COMMAX Access Control Solutions
When ADMIN is not registered
F1
*
*
> Admin ID > Admin verification > User . Enroll
#
#
#
F1
1. Press button
2. After “ Admin ID ” , press button
3. Verify Fingerprint or CD of the above Admin ID
(Access to the system menu)
4. Select “ Enroll ” and press button
5. Input password(USER ID) and set up the privilege ; User or Admin.
( After User ID, press and set the privilege using the and button )
6. Register fingerprints and/or card
( Refer to p. 16, Menu Navigation Buttons )
COMMAX Access Control Solutions
Register
Default admin ID is 1234. When the new admin is registered, 1234 does not work anymore.
Tip : In case of the absence of the admin, multiple admin is recommended.
1. Access to the system menu
5. Scan fingerprint 3tiems for one registration
10. Complete fingerprint registration
press button an back to home screen)
12. Select Card
15. Complete registration
COMMAX Access Control Solutions
User Registration
If doesn’t need 2nd fingerprint or CARD, it is possible to skip this process.
1. Access to the system menu
fingerprint and repeat the same process
10. Select 2nd fingerprint
11. Scan 2nd fingerprint three times
12. Complete fingerprint registration
button an back to home screen)
COMMAX Access Control Solutions
Admin Registration
If doesn’t need 2nd fingerprint or CARD, it is possible to skip this process.
#
1. Access to the system menu
(Refer to P. 17 or P. 18 for access to the system menu)
2. Select “User”
3. Select “Delete”
4. Input password (“User ID”) to delete
5. Place fingerprint or Card to delete
(If want to delete both fingerprint and card of the ID, select Delete All.
6. Press button after selection
7. “ Ye s ” and complete the delete
COMMAX Access Control Solutions
Delete
Same as registration process, it is able to delete 1st fingerprint, 2nd fingerprint and card in each.
If wish to delete all 3data, select“Delete All” and corresponding ID is deleted.
1. Access to the system menu
(Refer to P. 17 or P. 18 for access to the system menu)
2. Press button
3. Select “ User ”
4. Select “ Set Temp ID”
5. Input Temp ID ( upto 8 digits) and press
6. Input access admission times with this temp ID and press
(Min. 1, Max. 9)
7. Compete setup temp ID.
*
#
#
COMMAX Access Control Solutions
Set Temp ID
Temp ID cannot be an Admin and not use fingerprint Admin can determine access times of Temp ID (min. 1 ~ max. 9)
Access times are expired, Admin can revert it. emp ID leaves log data Pre-registered ID is not used as a temp ID.
SETTING 1.Basic 2.Advanced 3.AC Setting 4.Communication 5.Schedule 6.Log Setting
Basic
1.Time
2.Date
3.Date Format
4.Language
5.Use Busytone detection
6. Set Phone Numbers
Advanced
1.Vertification Mode
2.ID Mask
3.Use Tamer Alram
4.Use Touch Sensor
5.Celibrate Senseor
6.Restore Factory Settings
7.Clear General Log
8.Clear Management Log
9.Clear Enroll Date
AC Settings
1.Define Timezone
2.User Timezone
3.Lock Type
4.Lock Door Release Time
5.Door Open Warning
6.Re-access Count
7.Re-access Limit Time
8.Wiegand Format
9.Anti-Passback
COMMAX Access Control Solutions
T65
SETTING 1.Basic 2.Advanced 3.AC Setting 4.Communication 5.Schedule 6.Log Setting
Communication
1.Device ID
2.Baudrate
3.TCP/IP Settings
-DHCP
-IP Antipass
-Subnet Mask
-Default Gateway
-Port
-Mac Address
4.Communication Password
Schedule
1.Set Tmode
2.Ring Settings
3.Auto Door
4.Auto Funckey
5.None-Relat Funckey
6.Day Light
7.Holiday
8.Funckey Alarm
9.Idle Settings
Log Setting
1.Management Log Warning
2.General Log Warning
COMMAX Access Control Solutions
T65
1. Time
Set-up the time of the device
Device’s time is applied to the time of the event. So it is important the accurate time.
2. Date
Setup the date of the device.
3. Date Format (YYYY-MM-DD)
Define date format at home screen
4. Language (Korean/English)
Choose the language
5. Use Busy tone detection (No/Yes)
If the silent exceeds 1minute, the phone disconnected automatically.
Even visitors activate interphone, it returns standby mode and recommend to use.
6. Set Phone Numbers
When interphone is connected, the receivers can remote control the door with pass word.
Only registered phone numbers are able to control the door and available max. 100 phone numbers.
COMMAX Access Control Solutions
Basic
1. Verification Mode
Depends on the security level, it is able to adjust the verification mode.
2. ID mask
When the user input ID, it hides user ID as xxxxxx and enhance the security.
3. Use Tamer Alarm
When it detects tamper, it activate alarm.
4. Use Touch Sensor
If touch sensor is on, sensor lights off in normal condition and lights on when the user touch the sensor only.
5. Calibrate Sensor
Optical sensor perceive surroundings and optimize the brightness.
When use this function, it has to block extraneous light.
6. Restore Factory Settings
Reset all settings to the default
7. Clear General Log
Delete all general log data
8. Clear Management Log
Delete all management log data
9. Clear Enroll Data
Delete entire user data including fingerprint, card data and it is unrecoverable
COMMAX Access Control Solutions
Advanced
1. ANY MODE : Access granted with any form of authorization
2. FINGER : Fingerprint Only – No access with ID or Card
3. CD OR FP
4. ID&FP OR CD
5. ID&FP OR ID&CD
6. ID &FP OR CD & FP
7. OPEN : Always Open (Fail Safe Mode )
8. CLOSE : Always Closed (Fail-Secure Mode ) – No access with any form of authorization
9. CD : Card Only – No access with ID or Fingerprint
10. ID OR FP : ID or Fingerprint only – No access with Card
11. ID OR CD : ID or Card Only – No access with Fingerprint
12. ID & CD : Both ID and Card required for access – must punch in ID before Card authentication
13. CD & FP : Both Card and Fingerprint required for Access
– Card must be authorized before fingerprint authentication
14. ID & FP : Both ID and Fingerprint required for Access
– must punch in ID before fingerprint authentication
15. ID & CD & FP : all three formats needed for access
Verification Mode
COMMAX Access Control Solutions
1.Define Timezone : Able to set-up 256 timezones.
( Refer to Software (Guardian) manual 7.3 Time Zone set-up.
2.User Timezone : Able to allocate 2 time zone for each user. 0 for [ All Time ] and 257 for [ None Time ].
3.Lock Type : NC or NO Set up door lock type
4.Lock Door Release Time : Default 3sec. Available to adjust between 1 ~ 99sec.
5.Door Open Warning : Once door open, if the door remains open over setting condition, it activates alarm
6.Reaccess Count : No, 0~ 9 Limit reaccess count between no., 0 ~ 9times.
7.Reaccess Limit Time : Limit reaccess time between no. 0 ~ 600minutes.
8.Wiegand Format : 26,34,35,37,64
Designate wiegand output format 26,34,35,37, or 64.
Read all wiegand data regardless of wiegand settings
9.Anti-Passback : No / Yes
Anti-passback activates through external wiegand input.
If there is two controllers for enter and exit, re-enter is allowed only it has exit event data
(EX : Public Parking lot, Restricted Area, Membership center )
COMMAX Access Control Solutions
AC Settings
1 .Device ID (1 ~ 999)
Device ID ranges between 1 ~ 999.
When many devices are connected in one network, each device must have unique address.
2. Baud rate : 115200 bps
RS-485 Communication speed
3. TCP/IP Settings
- DHCP : No/ Yes
Choose DHCP on or off
- IP Address : 192.168.1.224
Setup IP Address
- Subnet Mask : 255.255.255.0
Setup subnet mask
- Default Gateway : 192.168.1.1
Setup default gateway
- Port : 5005
Setup TCP Port
- MAC Address
Displays MAC Address of the device
To connect device with software (Guardian) by TCP/IP ( LAN),
it must set-up IP Address, Subnet Mask, Gateway,
(All the above data is for reference only and an confirm the details in network
environment of the PC to connect)
4. Communication Password
If the communication password is not correct, it is impossible to communicate with the software
COMMAX Access Control Solutions
Communications Settings
1. Set Tmode
Setup the door mode and it is converted automatically according to the time and schedule.
Refer to Software (Guardian) manual 7-4 controller
Special function/ Door mode how to setup the door mode
2. Ring Settings
Setup the bell ring schedule.
Refer to Software (Guardian) manual 7-4 controller
Special function / Bell Time how to setup the bell rings
3. Auto Door
Setup the operation time of the automatic door
Refer to Software (Guardian) manual 7-4 controller
Special function
Auto Door how to setup the auto door.
4. Auto Funckey
At the designated date and time, the corresponding key is set-up as default.
Refer to Software (Guardian) manual 7-4 controller
Special function
auto F-Key how to setup the auto F-Key.
5. None-Relay Funckey
Setup none-relay Funckey and buzzer alarm key.
Refer to Software (Guardian) manual 7-4 controller
Special function
No act F-Key how to setup the No Act F-key.
COMMAX Access Control Solutions
Schedule
6. Day Light
Setup the daylight.
Refer to Software (Guardian) manual 7-4 controller
Special function
Daylight how to setup Daylight.
7. Holiday
Holiday settings must comply with the day of the week
Refer to Software (Guardian) manual 7-4 controller
Holiday setup
8. Funckey Alarm
Once input the alarm key and succeed to identify, it activates buzzer alarm or relay alarm.
9. CD2 Auto Funckey
Input card data to the external reader by Wiegand, and succeed to identify, it is used to save the event..
If a controller is connected to a reader, this function gives a function key to the external reader automatically,
thus a an automatically setup function key is given to a user who is authorized from an external reader.
Events of user entries from the reader are stored. (Ex. For time & attendance)
10. Idle Settings
LCD power cut off : 0 ~ 60minutes
IDLE mode : 0 ~ 60minutes
COMMAX Access Control Solutions
Schedule
1. Management Log Warning ( 0 ~ 100)
If the management logo exceeds the setting value, it alarms
2. General Log Warning
If the management logo exceeds the setting value, it alarms
COMMAX Access Control Solutions
Log Settings
Insert USB memory into the slot at the bottom of the device and
up/download the events data and update the firmware i
Download General log
Download new general events
Download All General log
Download all general events
Download Management log
Download new management events
Download All Management log
Download all management events
Download User Info
Download user data
Upload User info
Upload user data
Upgrade Firmware
Update Firmware
COMMAX Access Control Solutions
Use Memory
MEMORY
1. User :User numbers which is enrolled in the device
2. Fingerprint : Template numbers which is enrolled in the device
3. ID Card : ID Card numbers which is enrolled in the device
4. General Log : General log ( access event ) numbers
5. Management Log : Management log ( system event ) numbers
COMMAX Access Control Solutions
Memory
Device info is set from the manufacturer and the user cannot edit this info.
1. Release Date : Displays the device release date
2. Serial Number : Displays the device serial number
3. Manufacturer : Displays the device manufacturer
4. Product Name : Displays the device Name
5. Product Type : Displays the device Type
6. Engine Version : Displays the engine version
7. Firmware Version: Displays the firmware version
COMMAX Access Control Solutions
Device Info
1.View General Log : Search and view the general access event
2.View Management Log : Search and view the system management event
3.View User info : Search and view the numbers of the fingerprint and card
COMMAX Access Control Solutions
Advanced
Test All : Test overall status and functions of the device
Test Memory : Test memory and takes 1 ~ 2 minutes . After test, it reboots and displays the result
Test LCD : Test LCD
Test Sound ( Auto ) : Test Voice announcement automatically. If there is no voice chip, it finishes quickly
Test Sound ( Manual ) : Test Voice announcement manually.
Test Sensor : Test Finger sensor
Test Keyboard : Test keyboard
Test RTC : Test RTC
Test Case Status : Test the status of the case
Test Card Reader : Test the card reading
COMMAX Access Control Solutions
Self Test
Loading...