Commax DRC-900LC User Manual

Download

• Thank you for purchasing COMMAX products.

• Please carefully read this User’s Guide (in particular, precautions for safety) before using a product and follow

instructions to use a product exactly.

• The company is not responsible for any safety accidents caused by abnormal operation of the product.

User Manual

Anti Vandal lobby phone DRC-900LC/RF1

- Feature -

•Common 8 wires(When using the video phone)

•RF/ID

• Thank you for purchasing COMMAX products.

• Please carefully read this User’s Guide (in particular, precautions for safety) before using a product and follow

instructions to use a product exactly.

• The company is not responsible for any safety accidents caused by abnormal operation of the product.

 38 

Table of Contents

1. Greeting......................................................................................................................................1

2. Safety Warning & Caution..........................................................................................................2

3. Overview ...................................................................................................................................4

4. PIN Types .................................................................................................................................8

5. Setting PIN. ...............................................................................................................................9

6. Household PIN Confirmation ...................................................................................................12

7. Configuring Building and Serial Numbers in the Main Entrance Interphone ...........................13

8. Using Remote card keys(RF/ID) ..............................................................................................15

9. Electronic key setting ..............................................................................................................20

10. Door Release Time Setup......................................................................................................21

11. Line Call Setup.......................................................................................................................22

12. Page Signal Selection ...........................................................................................................23

13. The number of emitting chime setup .....................................................................................24

14. Video Out Impedance Adjustment..........................................................................................25

15. InputHousehold number.........................................................................................................26

16. A Talk volume control.............................................................................................................28

17. How to set the button lighting ................................................................................................29

18. Paging the Household............................................................................................................30

19. Paging the Guard Station.......................................................................................................30

20. Door Release Using the Household PIN................................................................................31

21. Door Release Using the Building (Management) PIN............................................................31

22. How to use lobby phone. .......................................................................................................32

23. Appendix (Various Program Summaries)...............................................................................33

24. Wiring Method ........................................................................................................................34

25. Miscellaneous ........................................................................................................................35

26. Part list

27. Specifications ........................................................................................................................35

...................................................................................................................................35

1. Greeting

* Thank you for purchasing a COMMAX product * This product is a high tech Main Entrance interphone that supports electronic and

remote keys features. Please read this manual carefully.

 1 

2. Safety Warning & Caution

Please follow the things described below in order to prevent any danger or property damage.

Prohibition.

Warning

Caution

t may cause a serious damage or

injury if violated.

t may cause a minor damage or

injury if violated.

No disassembly

Shows plugging out the power cord without an exception

Shows the warning and caution for an electric shock.

Shows the warning and caution for a fire.

Warning

o touch

ust follow strictly.

Please don’t use several products at the same time on one power socket.

It may cause a fire due to an abnormal overheating.

Please don’ product in the place where there is much oil, smoke or humidity.

·It may cause an electric

Power & Installation

t install the

shock or fire.

t bend the power

Please don’ cable excessively or it may cause an electric shock.

fire when using a damaged power cable.

Please don’t install the product with the lightening and thunder.

It may cause an electric

shock or fire.

t handle the power

Please don’ cable with a wet hand.

It may cause an electric shock.

Please don’

t use and connect this product with other products with different rated voltage

·It may cause a disorder or

fire.

Please plug out the power cable from the socket when not using it for a long period of time.

It may shorten the product lifespan or cause a fire.

When installing the product that generates heat, please install the product away from the wall (10cm) for the ventilation.

It may cause a fire due to the increased internal temperature.

 2 

Please don’t disassemble, repair or rebuild this product a

rbitrarily (please contact the

ervice center if a repair is

needed.

It may cause an electric

shock or fire.

Cleaning & UsePower & Installation

Warning

f an abnormal sound, burning

mell or smoke is coming out of the product, please plug out the power cable and contact a service center.

It may cause an electric

shock or fire.

Caution

Please don’t insert any metallic or burnable materials i

nto the ventilation hole.

t may cause an electric

shock or fire.

lease use only the designated

atteries for the products of

using DC power.

It may cause an electric

shock or fire.

Please plug the power cable firmly into the inner end

It may cause a fire.

Please be careful when using an AC circuit breaker since there is a possibility of an electric shock.

When cleaning the product, please rub it with a soft and dry cloth after plugging out the power cable. (Please don’ use any chemical products such as wax, benzene, alcohol or cleanser.)

Please hold the plug tightly when unplugging the power cable (a part of the copper wire may be disconnected if the grabbing is only made on the cord when pulling out the cable).

It may cause an electric shock or fire

Please check the use voltage and current for the DC-only products and use the appropriate rectifier.

It may cause a fire.

t drop the product

Please don’ on the ground and don’ a shock .

It may cause a failure.

When connecting the power cables after cutting the cable, please install the product with power off

It may cause an electric shock or fire

Please avoid direct rays of the sun or heating devices at a time of installation.

It may cause a fire.

Please use the designated connection cable within the

t apply

maximum calling distance designated for the product

It may reduce the product performance.

When installing the product, please fix it firmly while using the wall-mounting unit and screws.

It may cause an injury from the falling object.

Please don’t install the product on an unstable place or small support board.

It may cause an injury if it falls down while in use.

Cleaning & Use

 3 

3. Overview

3-1. Part name

NO. Description NO. Description

1 Camera

2 Speaker

3 FND Display

4 RF ID

5 Dial button

6 Microphone

7 Program button

8 Electronic-key button

9 Guard button

10 Cancel button

11 Call button

12 Wiring connection terminal

13 Reset switch

14 Switchgear connection terminal

 4 

3-2. Essentials

✽ Program Button ⑦ (P: Program )

This button is used to Program.

Program : Program Enter

✽ Electronic Key Button ⑧ (K : Key)

This button is used to release the door by using PIN. (Available only when the Electronic Key option has been set as OFF. When it is set as ON, Finger Print Recognition is enabled)

✽ Guard callt button ⑨ (G : Guard)

This function is to call the guard house

✽ Cancel Button ⑩ (X : Cancel)

This button is used to cancel the current operation.

✽ Reset Button ⑬

This button is used to reset the Building PIN or the Management PIN

If the Management PIN can not be remembered, press the Reset button

 5 

✽ Change the message on FND

To change the message on FND, press the Program button (P) for 5 seconds.

1) Displaying system version 0101-9901 SLI DRC-900L Ver.1.1

⇨

2) Displaying general message

⇨ hELLo hAPPy dAy

 6 

•Must know Before Use!

This button is used to cancel the current operation.

1) Accessing All Features with the Program Button

- When an error has been made as indicated by continuous beeps, please cancel and start again from the beginning.

Beep- Beep-Beep

(Error)

2) Forgotten PIN 2-1. Household PIN

Use the Household PIN verification feature of 6-1 retrieve the PIN. (Please inquire to the Guard Station or the Management Office)

2-2. Building PIN

Reenter using the Management PIN.

2-3. Management PIN

Press the Reset button. Both the Building and the Management Building PINs are reset to default.

3) All Remote Cardkey Deletion is to be used only when the unit is being initially installed.

4) Configuration Mode Indications Configured features are displayed on the Display Window when the Main Entrance interphone is not in use.

0101-9900 S-LI DRC-900L Ver1.1 Open

Start again from the beginning

Door status

Version No.

Series

Camera Impedance

Wiring Method

Serial Number

Building Number

 7 

4. PIN Types

4-1. Management PIN

- This PIN is for use by the person in charge of the Management Office.

- By default, this PIN is set as 4321.

- For convenience, hereafter management PIN.

4-2. Building PIN

- This is the common PIN for each main entrance.

- By default, this PIN is set as 1234.

- For convenience, hereafter management PIN.

4-3. Household PIN

- Each household has its own PIN.

- By default, this PIN is set as 1234.

- For convenience, hereafter management PIN.

P : Program K : Electronic Key E : Call

※ Old PIN

Default Management PIN : 4321 Default Building PIN : 1234 Default Household PIN : 1234

New PIN

※

New PIN to be set by the user.

 8 

5. Setting PIN.

5-1. Management PIN Setup

- P - Old Management PIN – E – 0 – E - New PIN – E

- Management PIN must be 4-digits long.

- 0000 will no be recognized as a valid PIN.

Press the Program button (P).

Press the Program Number 0.

Press the Call button (E).

Enter the old PIN 4321.

Press the

Call button (E).

Management PIN has been updated.

1. Press the Program button (P). (‘Prog’ will appear)

2. Enter the old PIN 4321.

3. Press the Call button (E).

4. Press the Program Number 0.

5. Press the Call button (E). (‘PASS’ will blink)

6. Enter the new PIN.

7. Press the Call button (E).

8. Management PIN has been updated.

Press the Call

button (E).

Enter the new PIN. Ex)1470

<Note> Be sure to change managing password ahead of use

 9 

5-2. Building PIN Setup

- P - Old Management PIN – E – 1 – E - New PIN – E

- Building PIN must be 4-digits long.

- 0000 will no be recognized as a valid PIN.

Press the Program button (P).

Press the Program Number 1.

Press the Call button (E).

1. Press the Program button (P). ( Prog will appear)

2. Enter the old PIN 4321.

3. Press the Call button (E).

4. Press the Program Number 1..

5. Press the Call button (E). ( PASS will blink)

6. Enter the new PIN.

7. Press the Call button (E).

8. Building PIN has been updated

Press the

Call button (E)

Enter the old PIN 4321.

Building PIN has been updated.

Press the

Call button (E).

Enter the new PIN. Ex)2580

 10 

5-3. Household PIN Setup

- K – Program Number – E – Household Number – E – Old Household PIN – E – New PIN – P

- Household PIN must be 4-digits long.

- 0000, 1234 will no be recognized as a valid PIN.

- This method of Household PIN change may vary depending on household interphone types. (Types that support PIN changing from the household interphone)

Electronic Key button (K).

Household Number. Ex)101

Press the

Call button (E).

Press the Program Number (20).

Press the

Call button (E).

Enter the new Household PIN.

1. Press the Electronic Key button (K).

2. Press the Program Number 20.

3. Press the Call button (E). (‘hono’ will blink)

4. Enter the Household Number.

5. Press the Call button (E). (‘PASS’ will blink)

6. Enter the old Household PIN.

7. Press the Call button (E). (‘PASS’ will blink)

8. Enter the new Household PIN.

9. Press the Program button (P).

Household PIN has been updated.

Press the

Call button (E).

Enter the old PIN. Ex)1234

Press the Program button (P).

 11 

6. Household PIN Confirmation

6-1. Household PIN Confirmation

- P - Management PIN - E - Program Number - E – Household Number – E

Press the Program button (P).

Press the Program Number(16).

Press the Call button (E).

Enter the Management PIN.

Press the Call button (E).

Household Number. Ex)101

Ex) 1 2 3 4 for household 101

1. Press the Program button (P). (‘Prog’ will appear)

2. Enter the Management PIN.

3. Press the Call button (E).

4. Press the Program Number (16).

5. Press the Call button (E). (‘hono’ will blink)

6. Enter the Household Number. Ex)101

7. Press the Call button (E). (The Household PIN will be indicated)

 12 

7. Configuring Building and Serial Numbers in the Main Entrance Interphone

P-Management PIN - E - 2 - E - Serial Number - E

Press the Program button (P).

Press the Program Number(2).

Press the Call button.(E)

Enter the Management PIN.

Press the Call button (E). The Serial Number previously entered will be indicated

Press the Call button (E).

Enter the New Serial Number EX)101

Serial Number has been updated.

1. Press the Program button (P). ( 'Prog' will appear)

2. Enter the Management PIN.

3. Press the Call button (E).

4. Press the Program Number (2) .

5. Press the Call button (E). (The Serial Number previously entered will be indicated)

6. Enter the new Serial Number.

7. Press the Call button Serial Number has been updated.

 13 

7-2. Configuring Serial Number from the Main Entrance Interphone

P – Management PIN - E - 3 - Serial Number – E

Press the Program button (P).

Press the Program Number (3).

Press the Call button (E)

Enter the Management PIN.

Press the Call button (E)

(The Serial Number previously

entered will be indicated)

ress the Call button (E).

Enter the new Serial Number. Ex) No 2

1. Press the Program button (P). (‘Prog’ will appear)

2. Enter the Management PIN.

3. Press the Call button (E).

4. Press the Program Number (3).

5. Press the Call button (E). (The Serial Number previously entered will be indicated)

6. Enter the new Serial Number.

7. Press the Call button. Serial Number has been updated.

 14 

8. Using Remote Cardkeys (RF/ID)

8-1. Testing Remote Cardkeys

-P - Management PIN - E - 9 - E - Card Test - X (Cancel)

-This feature is used to test Remote Cardkeys.

Press the Program button (P).

Press the

Program Number (9).

Press the Cancel button (X) to end Remote Cardkey testing

Enter the Building (Management) PIN.

Press the

Call button (E).

Press the Card Here

ex) Card Number 3579

Place the Remote Cardkey to the RF/ID Receptor, and the Card Number will appear on the Display Window (FND).

✽

To confirm others cardkey, place continuedly the

Remote Cardkey to the RF/ID Recepter

Press the

Call button (E).

1. Press the Program button (P). (‘Prog’ will appear)

2. Enter the Building Management PIN.

3. Press the Call button (E).

4. Press number 9 (Remote Cardkey Test).

5. Press the Call button. (‘Cdtt’ will blink)

6. Place the Remote Cardkey to the RF/ID Receptor, and the Card Number will appear on the Display Window (FND).

7. Press the Cancel button (X) to end Remote Cardkey testing.

 15 

8-2. Remote Cardkey Registration

- P - Building Management PIN - E - 10 - E - Card Registration - X (Cancel)

Press the Program button (P).

Press the

Program Number (10).

nter the Building (Management) PIN.

Press the

Call button (E).

x) Building PIN

Press the Card Here

Place the Remote Cardkey to the RF/ID Receptor, and ‘Cdsv’ or ‘CdAL’ will appear

Press the

all button (E).

Newly

Registered Card

Previously

Registered Card

Press the Cancel button (X) to end Remote Cardkey testing

✽

To confirm others cardkey, place continuedly the

Remote Cardkey to the RF/ID Recepter

<Note>

CdSv: Newly Registered Card (Successful registration is indicated by a beep) CdAl: Previously Registered Card (Rejected registration is indicated by two beeps)

✽

Up to 1024 Remote Cardkeys can be registered. (Without a computer connected) Please record registered Remote Cardkey’s serial number for future reference.

✽

CdFu : Exceeding card storage limit (If you didn't register a card, please delete all

saved card referring to 8-5 chapter) <Caution> Do not turn off the products within ten seconds after registering RF cards. It might cause a problem in saving RF cards information.

 16 

8-3. Individual Deletion of Remote Cardkeys

- P - Management PIN - E - 12 - E - Card Deletion - X (Cancel)

ress the Program button (P).

Press the

Program Number (12).

Enter the Building (Management) PIN.

Press the

Call button (E).

Press the Cancel button (X) to terminate the feature

ex) Building PIN

1. Place the Card on top of the RF/ID Receiver, and

2. Enter Card Number and press Call button, and will

Press the Card Here

will delete Card Number

delete Card Number

ex) For Card Number 19919 delete

1. Press the Program button (P). (‘Prog’will appear)

2. Enter the Management PIN.

3. Press the Call button (E).

4. Press number 12 (Individual Remote Cardkey Deletion).

5. Press the Call button (E). (‘

CddE’will blink)

6. Enter the 5-digit Card Number and press the Call button (E). (Check on the right side of the RF/ID Card) Or place the Card on top of the RF/ID Receiver.

7. Press the Cancel button (X) to terminate the feature

Press the

all button (E).

ex) Card Number

19919

 17 

8-4. Confirming Remote Cardkey Registration

- P - Building Management PIN - E - 13 - E - Card Confirmation - X (Cancel)

nter the Building (Management) PIN.

ress the Program button (P).

ex) Building PIN

Press the

Call button (E).

Press the

Program Number (13).

Press the

Call button (E).

Press the Card Here

1. Place the Card on top of the RF/ID Receiver, and will confirm.

2. Enter Card Number and press Call button, and will confirm Remote Cardkey Registration.

ex) Card Number

19919

ex) For Card Number 19919 Confirm

Press the Cancel button (X) to terminate the feature

Confirm Card

No Confirm Card

1. Press the Program button (P). (‘Prog’will appear)

2. Enter the Building Management PIN.

3. Press the Call button (E).

4. Enter number 13 (Remote Cardkey Confirmation).

5. Press the Call button (E). (‘CddE’will blink)

6. Enter the 5-digit Card Number and press the Call button (E). (Check the right side of the RF/ID Card) Or place the Card on top of the RF/ID Receiver.

7. Press the Cancel button (X) to terminate the feature.

 18 

8-5. All Remote Cardkey deletion

- P - Building Management PIN - E - 11 - E - E

- Refrain from deleting all Remote Cardkeys, except for during installation.

ress the

ress the Program button (P).

nter the Building (Management) PIN.

x) Building PIN

all button (E).

Press the

Program Number (11).

Call button (E).

All Remote Cardkey mode All Remote Cardkey mode

1. Press the Program button (P). (‘Prog’will appear)

2. Enter the Building Management PIN.

3. Press the Call button (E).

4. Enter number 11 (All Remote Cardkey Delete Number).

5. Press the Call button (E). (‘

dEL’will blink)

6. Press the Call button (E) again.

The number displayed on screen will change.

7. Press the Cancel button (X) to terminate the feature.

Press the

Call button (E).

 19 

9. Electronic key setting

- P- Management PIN - E - 8 - E - 0 – E : Deactivate usage of electronic keys ( Available PIN number access)

- P-Management PIN - E - 8 - E - E - : Deactivate usage of electronic keys Door ( Not available PIN access)

- This feature is for deactivating or activating the use of electronic keys in door access .

Press the Program button (P).

Press the Program Number.

Activate electronic key

Deactivate electronic key

1. Press the Program button (P). (‘Prog’ will appear)

2. Enter the Management PIN.

3. Press the Call button (E).

4. Enter number 8 ( Monitor setting number for surveillance).

5. Press the Call button (E). (Displaying previous setting on the screen)

6. Select a mode. (0 : Activate electronic key use) (1 : Deactivate electronic key use)

7. Press the Call button (E) again. (Modification updated)

Enter the Management PIN.

Press the Call button (E).

Previous selection is displayed

Press the Call button (E).

Completion of activating electronic key

 20 

10. Door Release Time Setup

- P – Management PIN – E – 4 – E – Door Release Time - E

- This feature asjusts the door release time.

Press the Program button (P).

Enter the Management PIN.

Press the Program Number (4).

Choose a time

Use numbers from 1 to 25.

ex) Door Release time

Selected 10 seconds

1. Press the Program button (P). (‘Prog’ will appear)

2. Enter the Management PIN.

3. Press the Call button (E).

4. Press number 4 (Door Release Time Setup).

5. Press the Call button (E). (Previous selection is displayed.)

6. Choose a time. (From 1 to 25 seconds) Use numbers from 1 to 25.

7. Press the Call button (E). (Modification updated).

Press the Call button (E).

Press the Call button (E)

Modification updated

Press the Call button (E).

Previous selection is displayed.

 21 

11. Line Call Setup

- P-Management PIN - E - 21 - E - 0 - E : All calls

- P-Management PIN - E - 21 - E – 0103 - E : Line call ex) This function is for calling to specified line like from 1sthouse line to 3rdhouse line.

Press the Program button (P).

Press the Program Number (21).

Enter the Line. st

ex) Call the 1ST Line 3 Line

Enter the Management PIN.

Press the Call button (E).

Press the Call button (E)

Modification updated

1. Press the Program button (P). (' Prog' will appear)

2. Enter the Management PIN.

3. Press the Call button (E).

4. Press number 21

5. Press the Call button (E). (Previous selection is displayed)

6. Choose a line you want to call ex) In case of calling to 1sthouse to 3rdhouse line, input “0103”

7. Press the Call button (E). (Modification updated)

Press the Call button (E).

Previous selection is displayed.

 22 

12. Page Signal Selection

- P-Management PIN - E - 5 - E - 0 - E: Melody Tone

- P-Management PIN - E - 5 - E - 1 - E: Bell (Ringer)

- This feature sets the Recall tone heard when Households or the Guardhouse is paged from the Main Entrance.

Press the Program button (P).

Enter the Management PIN.

Ex) Building PIN

Press the Program Number (5).

Input line

0 : Melody Tone 1 : BELL Tone (RINGER)

1. Press the Program button (P). ( 'Prog' will appear)

2. Enter the Building (Management) PIN.

3. Press the Call button (E).

4. Press number 5 (Page Signal Selection).

5. Press the Call button (E). (Previous selection is displayed)

6. Select a page signal. 0 : Melody Tone 1 : Bell (Ringer)

7. Press the Call button (E). (Page signal updated)

Press the Call button (E).

Page signal updated.

Press the Call button (E).

The current capacity is displayed.

 23 

13. The number of emitting chime setup

- P-Management PIN - E - 7 - E - 0 - E: Constant call

- P-Management PIN - E - 7 - E - 1 - E: Call once

- This function is to set the call sound when make a call to household or guard station from the lobby.

Press the Program button (P).

Enter the Management PIN.

Ex) Building PIN

Press the Program Number (7).

Choose the mode.

0 : Constant call

1 : Call once

1. Press the Program button (P). ( 'Prog' will appear)

2. Enter the Management PIN.

3. Press the Call button (E).

4. Press number 7 (Wiring Method Selection).

5. Press the Call button (E). (Previous selection is displayed)

6. Select a wiring method. 0 : Contrast call 1 : Call once

7. Press the Call button (E). (Save new setting)

Press the Call button (E).

Completion of setup

Press the Call button (E).

The current capacity is displayed.

 24 

14. Video Out Impedance Adjustment

- P-Building (Management) PIN - E - 6 - E - 0 - E: Short Distance

- P-Building (Management) PIN - E - 6 - E - 1 - E: Long Distance

- By default, the unit is set for short distance. Do not change if possible.

Press the Program button (P).

Enter the Management PIN.

Press the Program Number (6).

Select a Impedance.

0 : Short Distance 1 : Long Distance

ex) Impedance Adjusted long distance

1. Press the Program button (P). ( 'Prog' will appear)

2. Enter the Building (Management) PIN.

3. Press the Call button (E).

4. Press number 6 (Wiring Method Selection).

5. Press the Call button (E). (Previous selection is displayed)

6. Select a wiring method. 0 : Short Distance 1 : Long Distance

7. Press the Call button (E). (Save new setting)

Press the Call button (E).

Impedance selection update

Press the Call button (E).

The current capacity is displayed.

 25 

15. InputHousehold number

- P-Management PIN - E - 15 - E - Household Number - E-Multi Sub number - E

- This function is for inputting household number with lobbyphone in case of a guard stationunit is not installed

Press the Program button (P).

Press the Program Number (15).

Lift up the receiver from the Household and press the Guard button to page the Main Entrance Interphone, where the Household Number will be displayed. (Then, the displayed number must be changed for it is the default number from the factory.)

Enter the Household number and press the Program button.

Ex) Entering as Unit 101

Enter the Multi Sub number "0" and press the Page button (E).

ex) Entering as Master

Enter the Management PIN.

Press the Call button (E).

ex) Entering as first

1234

Press the Call button (E).

Household PIN Entry Mode

Press the Call button (E).

Follow the same procedure to enter other Households. Press the Cancel button (X) to end.

 26 

1. Press the Program button(P). (‘Prog’willappear)

2. Enter the Management PIN.

3. Press the Page button(E).

4. Enter number 15 (HouseholdInterphone Diagnosis).

5. Press the Page button (E). (‘idCh’ will appear)

6. Call to guard station from household

7. The Household’s status is shownon the displaywindow(FND).

8. Household Number,then press the Page button (E). (‘sub’willappear)

9. Input Multi sub number “0”, then press the Call button(E).

10. To check other Households, repeat steps 6~ 9.

Press theCancel button (X) to terminate the feature.

 27 

16. A Talk volume control

- P - Administration password - E - 28 - E - Volume(Level) - E

- Through this function, You can adjust the speaker volume of the common lobby phone

Press the Program button (P).

Press the Program Number (28).

Enter the value of the speaker volume, between from 1 to 4

Ex) When you want 2 as the value of the speaker volume

1. Press the program button. “Prog” word will appear.

2. Enter the administration password.

3. Press the call button “E”.

4. Enter no. “28”, (the number to control the speaker volume)

5. Press the call button “E” (The value of the speaker volume, already inputted, will appear)

6. Enter the value of the speaker volume, from 1 to 4. (If it indicates “2”, it is 2 level of volume.)

7. Press the call button “E” (The value of the speaker volume is adjusted)

Enter the Management PIN.

Press the Call button (E).

Complete to set the speaker volume

Press the Call button (E).

 28 

ვ඾ໞ቙ ઋၼ ႕വጢཱཪဣ

 " ลእቤᇚཪ ลእვ඾ 76  " ጪໞ 76

M`ვ඾ໞ቙ ઋၼ ጪໞ 76ၹു ጥ ે၏

ลእ ვ඾ໞ቙ ໼Ⴣ ဲൔ

17. How to set the button linghting

- P- Administration password - E - 27 - E - 0 - E : Light on (When it is touched)

- P- Administration password - E - 27 - E - 1 - E : Light on (Always)

- Through this function, you can adjust the light of the key button.

Press the Program button (P).

Press the Program Number (27).

Enter the lighting status value.

0 : Button light ON when touching the

button.

1: ON all the time

Ex) In case of settingthe lighting condition ON all the time

1. Press program(P) button. ("Prog" will be turned on)

2. Enter the administration password

3. Press the call(E) button

4. Enter No.27 button(Button for light control)

5. Press the call(E) button Inputted value will appear.

6. Selecet the light setting (Default is 0) 0: Light on (When it is touched) 1: Light on (Always)

7. Press call(E) button (Adjusted value will be inputted)

Enter the Management PIN.

Press the Call button (E).

Complete to set the speaker volume

 29 

18. Paging the Household

nter the Household Number

x) unit 101

Wait for a reply.

Press the page button. A paging tone will sound.

ress the Call button (E).

Start to conversation

19. Paging the Guard Station

Press the Guard button.

Wait for reply.

Press the Page button. A paging tone will sound.

Press the Call button (E).

Start to conversation

 30 

20. Door Release Using the Household PIN

* Household Number – K – Household PIN - E

Enter the Household Number.

x) To open the door of unit 101

Press the Electronic key button.

Enter the Household PIN.

Press the Page button.

Press the Call button (E).

21. Door Release Using the Building (Management) PIN

* G – K – Building (Management) PIN - E

Press the Guard button.

Enter the Building or the Management PIN.

Press the Electronic key button.

Press the Page button.

Press the Call button (E).

 31 

22. How to use lobby phone.

* Calling to household from lobby phone * Household number – E

Press the household number

ex)In case of household 101

ress the Call button.

Emit call sounds

* Opening door with household PIN * Household number – K – household PIN – E

Press the household number

ex)In case of household 101

Press the Household PIN

Press the Key button

Press the Call button

Press the Call button (E).

 32 

23. Appendix (Various Program Summaries)

Various PIN Programs

1. P - Old Management PIN - E - 0 - E - New PIN- E: Management PIN Change

2. P- Old Management PIN -E -1 - E - New PIN - E: Building PIN Change

3. K - 20 - E - Household Number - E - Old Household PIN - E - New PIN - P: Household PIN Change

4. P - Management PIN - E - 16 - E - Household Number - E: Household PIN Confirmation

Configuring Building and Serial Numbers from the Main Entrance Interphone

1. P - Management PIN - E - 2 - E - Building Number - E : Building Number Setup

2. P - Management PIN - E - 3 - E - Serial Number - E : Serial Number Setup

Door Release Using Various PINs

1. G - K - Building (Management) PIN - E : Door release using Building (Management) PIN

2. Household Number - K - Household PIN - E : Door release using Household PIN

Other Feature Setup Methods

1. P - Management PIN - E - 4 - E : Door Release Time Setup

2. P - Management PIN - E - 5 - E : Page signal selection

3. P - Management PIN - E - 6 - E : Wiring Method Selection

4. P - Management PIN - E - 15 - E : Household Number Registration

 33 

24. Wiring Method

Lobby camera phone(DRC-900LC)

 34 

25. Miscellaneous

※ Please carefully read this User’s Guide before calling service man After checking the entire

check list, please contact customer service center. We will do our best to make you satisfy with our services.

26. Part list

MANUAL

27. Specifications

Installation Method Flush Mounted Model Name DRC-900LC/RF1 Transmission System Household (8 wire), Guard (4 wire) Rated Voltage 12V , 0.5A Power Consumption Standby: 200mA, Max : 500mA Conversation Hands-free Frequency 15.735KHz, 60Hz / 15.625KHz, 50Hz Camera C-MOS(Pin Hole type) Effective Viewing Angle Horizontal : 47˚, Vertical : 34˚

Minimum Illumination 0.1Lux(Within 300 mm from the camera) Distance UTP cable 300meter Bulit-in light LED Temperture

Dimension 136(W) X 260(H) X 36(D)mm

-20

℃ (tested up to -40℃)~ +50℃

 35 

Memo

 36 

513-11, Sangdaewon-dong, Jungwon-gu, Seongnam-si, Gyeonggi-do, Korea Int’l Business Dept. Tel. : +82-31-7393-540~550 Fax. : +82-31-745-2133 Web site : www.commax.com

PM10900LCR10

Printed In Korea / 2014.01.104

Commax DRC-900LC User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual