Commax DRC-40DK, DRC-41DK User Manual

User Manual

User Manual DRC-40DK/41DK

• Thank you for purchasing COMMAX products.

• Thank you for purchasing COMMAX products.

• Please carefully read this User’s Guide (in particular, precautions for safety) before using a product and follow

• Please carefully read this User’s Guide (in particular, precautions for safety) before using a product and follow

instructions to use a product exactly.

instructions to use a product exactly.

• The company is not responsible for any safety accidents caused by abnormal operation of the product.

• The company is not responsible for any safety accidents caused by abnormal operation of the product.

Contents

Safety Warning & Caution ······································· 2

1. Overview ························································ 4

2. How to use ····················································· 4

3. Wiring Diagram ·············································· 10

4. Installation ···················································· 11

5. Package ······················································· 11

6. Specication ················································· 12

Safety Warning & Caution

Please follow the things described below in order to prevent any
danger or property damage.

Prohibition.

Warning

Caution

It may cause a serious damage or
injury if violated.

It may cause a minor damage or
injury if violated.

No disassembly

No touch

Must follow strictly.

Shows plugging out the power cord
without an exception

Shows the warning and caution for an electric shock.

Shows the warning and caution for a fire.

Warning

Please don’t use several
products at the same time on
one power socket.

·It may cause a fire due to an

abnormal overheating.

Please don’ t install the
product in the place where
there is much oil, smoke or
humidity.

·It may cause an electric

shock or fire.

Power & Installation

Please don’t bend the power
cable excessively or it may
cause an electric shock.

·fire when using a damaged

power cable.

Please don’ t install the
product with the lightening
and thunder.

·It may cause an electric

shock or fire.

Please don’t handle the power
cable with a wet hand.

·It may cause an electric

shock.

Please don’t use and connect
this product with other
products with different rated
voltage

·It may cause a disorder or

fire.

Please plug out the power
cable from the socket when
not using it for a long period
of time.

·It may shorten the product

lifespan or cause a fire.

When installing the product
that generates heat, please
install the product away from
the wall (10cm) for the
ventilation.

·It may cause a fire due to

the increased internal
temperature.

2

2

Warning

Please don’t disassemble,
repair or rebuild this product
arbitrarily (please contact the
service center if a repair is
needed.

·It may cause an electric

shock or fire.

Cleaning & UsePower & Installation

Please plug the power cable
firmly into the inner end

·It may cause a fire.

Please be careful when using
an AC circuit breaker since
there is a possibility of an
electric shock.

If an abnormal sound, burning
smell or smoke is coming out
of the product, please plug out
the power cable and contact a
service center.

·It may cause an electric

shock or fire.

Caution

Please hold the plug tightly
when unplugging the power
cable (a part of the copper
wire may be disconnected if
the grabbing is only made on
the cord when pulling out the
cable).

·It may cause an electric

shock or fire

Please check the use voltage
and current for the DC-only
products and use the
appropriate rectifier.

·It may cause a fire.

Please don’t insert any
metallic or burnable materials
into the ventilation hole.

·It may cause an electric

shock or fire.

When connecting the power
cables after cutting the cable,
please install the product with
power off

·It may cause an electric

shock or fire

Please avoid direct rays of the
sun or heating devices at a
time of installation.

·It may cause a fire.

Please use only the designated
batteries for the products of
using DC power.

·It may cause an electric

shock or fire.

When installing the product,
please fix it firmly while using
the wall-mounting unit and
screws.

·It may cause an injury from

the falling object.

Please don’ t install the
product on an unstable place
or small support board.

·It may cause an injury if it

falls down while in use.

When cleaning the product,
please rub it with a soft and
dry cloth after plugging out
the power cable. (Please don’t
use any chemical products
such as wax, benzene, alcohol
or cleanser.)

Cleaning & Use

Please don’t drop the product
on the ground and don’t apply
a shock .

·It may cause a failure.

Please use the designated
connection cable within the
maximum calling distance
designated for the product

·It may reduce the product

performance.

3

1.

Overview

No. contents No. contents

Camera

1

Microphone

2

3 White LED & Illuminance sensor 8 Call button

4 Keypad button 9 RF Card Tag

5 Back/Cancel button 10 Camera angle adjustment

11 Connecting port/ WIRE for door realese 12 Anti-theft switch

6 Enter button

7 Speaker

2.

How to use

* Default behavior

- This product uses DC 12V / 1A adapter (RF-1A recommended, sold separately).

- If the power supply from the adapter is poor (disconnection or malfunction), the power
supplied from the monitor can be used as an emergency power source.

<Notes when using emergency power>

1) The emergency power source is supplied from monitor for 30 seconds when the
monitor is called by the camera.

2) In this case, some functions may cause difference from normal operation.
(Required function such as door opening is normal.)

3) Emergency power may not be used if wiring is poor or the distance is too long.

4

* Button description

Image Description

Back, Cancel ⑤ (C : Cancel)

Use this button to cancel the function.

OK Button ⑥ (E : Enter)

Use this button for setting and execution.

* Anti-theft alarm function ⑫

- To prevent the device from being stolen, the alarm sounds when removed from the wall.
However, the alarm sounds only when power is supplied to the unit.

- To enhance security function, the automatic call is sent to monitor call as the alarm occurs.
The automatic call operates at all time when removed from the wall, regardless of power
supply status.

* Reset password

- If you forget your password, you can reset it as follows.

1) With the monitor, enter the door camera monitoring function.
Try to press door opening button 7 times quickly within 20 seconds.

2) Then, LED of the camera is blinking and push OK Button ( E ) for 3 seconds to reset
password.

2-2. Set the functions

<Required>

1) The initial password is 1.2.3.4. Be sure to change the initial password before use.

2) 0000, 1234, 4321 can not be set as a password.

3) Password can be set from 4 to 12 digits.
(The password out of this range is not available)

2-2-1. Password setting

1) Password registration / change

Press program number (0) and press OK button (E)

①
② Enter the existing password (Initial: 1, 2, 3, 4) and press the OK button (E)
③ If the password change mode is successfully entered, the KEY LED will blink.
④ Click the new password to be changed.
⑤ Press the OK button (E), the key LED stops blinking and the setting is completed.

2) RF card registration

- Up to 1,024 cards can be registered.

① Press program number (3) and press OK button (E)
② Enter the password and press the OK button (E).
③ When the RF card registration mode is successfully entered, the KEY LED will blink.
④ Tag the card to be registered to the RF receiver.

If you tag another card continuously, you can register all the cards at once.

⑤ Press the Cancel button (C) and the KEY LED stops blinking and registration is

completed.

6

3) Delete individual RF cards

Press program number (4) and press OK button (E)

①
② Enter the password and press the OK button (E).
③ When individual deletion mode is successfully entered, the KEY LED will blink.
④ Tag the card to be deleted to the RF receiver.

If you tag another card continuously, you can delete multiple cards at once.

⑤ Press the Cancel button (C) and the KEY LED stops blinking and individual deletion

is completed.

4) Delete all RF cards

① Press program number (5) and press OK button (E)
② Enter the password and press the OK button (E).
③ When all deletion mode is successfully entered, the KEY LED will blink.
④ Press and hold the OK button (E) for 2 seconds, the whole deletion will proceed

with the beep sound.

⑤ When the whole deletion is completed, beep sound and KEY LED will stop..

5) Door opening with password

- Door open by Password

① After entering the password, press the door number you want to open and then press

OK button (E).

ex) When opening door # 1: 2580 -> 1 -> OK button (E)

- Door open by RF card

① After tagging RF card to the RF receiver, press the door number you want to open

ex) When opening door number 1: Card tag -> 1

② When the door is opened successfully, the operation is completed with the beep

sound.

6) Communication Volume adjustment

① Press program number (6) and press OK button (E)
② Enter the password and press the OK button (E).
③ When the call volume control mode is successfully entered, the KEY LED will blink.
④ The volume of communication can be adjusted from level 1 to 3.

(Enter the number between 1~3.)

⑤ After enter the level number, press the OK button (E) and the key LED stops blinking

and the setting is completed. When completed, beep sound is heard as the number
of level.

8

7) Beep(Touch and so on) Volume adjustment

① Press program number (7) and press OK button (E)
② Enter the password and press the OK button (E).
③ When the beep volume control mode is successfully entered, the KEY LED will

blink.

④ The beep volume can be adjusted from level 1 to 2.

(Enter the number between 1~2.)

⑤ After enter the level number, press the OK button (E) and the key LED stops

blinking and the setting is completed. When completed, beep sound is heard as
the number of level.

<Notes>

1) Even if the beep volume is adjusted, during Calling and Communication mode, it
is fixed in level 1 to maintain Communication quality

(It cannot be adjust the beep volume during Calling and Communication mode)

8) ON/OFF Anti-theft switch

① Press program number (8) and press OK button (E)
② Enter the password and press the OK button (E).
③ When anti-theft setting mode is successfully entered, the KEY LED will blink.
④ Anti-theft function OFF : Enter 0

Anti-theft function ON : Enter 1

⑤ Press the OK button (E) as key LED stops blinking and the setting is completed.

<Notes>

1) After installing the unit on the wall, turn on the anti-theft switch.

2) If the unit is detached from the wall, an alarm occurs.
In this case, the alarm will stop 10 seconds after the unit is re-attached to the wall.
The alarm can be turned off with above program (8) while alarm rings.

9) Touch LED setting

Press program number (9) and press OK button (E)

①
② Enter the password and press the OK button (E).
③ If touch LED setting mode is successfully entered, the KEY LED will blink.
④

LED ON only when the key touched: Input 0

LED ON every time with power supplied: Input 1

⑤ After entering the number, press the OK button (E) and the key LED stops blinking

and the setting is completed.

3.

Wiring Diagram

10

* Precautions

- When wiring the household monitor, connect as follows.
Failure to do the wiring as shown below may cause the video / audio noise.

4.

Installation

5.

Package

Item Description Qty

CONN. 4Px300 4 wire connector

CONN. 2Px300 2 wire connector

Bracket Bracket for installation

Screw GH1T 4x18 Bracket screw

Screw PHM 3x8 Bracket + Monitor

User Manual English version manual













6.

Specification

Model DRC-40DK/41DK

Power 12VDC/1A (Adaptor)

12VDC (emergency power from monitor

Communication Duplex communication

Min. illumination 0.1Lux (up to 300mm from camera / with normal LED operation)

Illumination White LED equipped (night vision)

Image sensor CMOS IMAGE SENSOR (0.52 megapixels)

Imaging angle 93° horizontal, 50° vertical, 110° diagonal

Adjustable angle 13° (pan and tilt)

RF Module 13.56MHz

Operation temp.

Dimension (mm) DRC-40DK : 127(W)x193(H)x54(D), DRC-41DK : 127(W)x193(H)x63(D)

Distance

-10℃(tested up to -40℃) ~ +50℃

28 meters (Φ 0.5 UTP), It must be observed.

Resistance under 10 Ω per 100 meters on UTP Cat 5e.

<Caution>
We recommend the COMMAX adaptor.
We are not responsible for problem caused by the use of adaptors of other company.

12

• Thank you for purchasing COMMAX products.

• Please carefully read this User’s Guide (in particular, precautions for safety) before using a product and follow

instructions to use a product exactly.

• The company is not responsible for any safety accidents caused by abnormal operation of the product.

• Thank you for purchasing COMMAX products.

• Please carefully read this User’s Guide (in particular, precautions for safety) before using a product and follow

instructions to use a product exactly.

• The company is not responsible for any safety accidents caused by abnormal operation of the product.

Color Video Door Phone CDV-43KM / CDV-43KM2

User Manual

513-11, Sangdaewon-dong, Jungwon-gu, Seongnam-si, Gyeonggi-do, Korea
Int’l Business Dept. Tel. : [phone]~550 Fax. : [phone]
Web site : www.commax.com

PM0743KM0010

Printed In Korea / 2016.04.104