TROUBLESHOOTING
1. When the image does not appear o n the screen, check the power source for the monitor and camera.
Make sure that the voltage and po larity are properly connected and correctly supplied.
2. When the image is too dim, check if the lens is stained.
If dirty, clean the lens with a clean soft clot h. If clean, adjust the back focus of the lens.
3. When the camera does not work properly, the camera housing is too hot or black lines appear on the screen,
check if you have connected the ca mera to a proper power source. If there is no problem with
the power connection, turn the camera off immediately and contact our service department for assistance.
4. When the screen blinks too much, check if th e camera is facing directly toward the sun or a fluorescent light.
If so, adjust the angle or location o f the camera.
MODEL : DCP-328R-S
WARRANTY
1. Products are supplied with 2 year limited warranty from th e date of purchase.
We will repair or replace the defective item with a new o r factory rebuilt replacement.
2. Transportation of the product to our se rvice center is the responsibility of the user.
Repaired or replaced product will be returned p repaid during the warranty period.
3. This warranty applies to the original purchaser on ly.
4. This warranty will be invalid if unauthorized repair or modificat ions are made to the unit or in any
case of accident, misuse or damage cause d by improper installation or altered serial numbers.
5. The liability of the company has limited the co st of repair/replacement of the unit under warranty.
6. If you need warranty service, please return t he product to your distributor/dealer.
Proof of pruchase may be required.
WARRANTY CARD
FEATURES
- High Resolution 630TV Lines
- Fixed Board Lens (Options)
- 80Ø Internal Dome Camera
- 0 Lux for Infrared Lighting Conditions
-
3Axis Gimbal Bracket
- OSD Control
Indoor 3 Axis IR Dome
Camera
1/3" High Resolution CCD
PRODUCT NAME
DATE OF PURCHASE
WARRANTY DATE
ADDRESS OF CUSTOMER
CONTACT
- Please read the instruction manual again before asking for the A/S
- Please explain exacity what the problem you have is,
NAME
TEL
NAME
AGENT
TEL
WARRANTY YEAR
/ DAY /M /Y
2 YEAR
ROHS
3-AXIS DAY & NIGHT
Board Lens
User's Manual
D-WDR
①
Fixed Board Lens
②
Gimbal Bracket
②
ITEM NTSC PAL
Total Pixels 811(H) x 508(V) 795(H) x 596(V)
Effective Pixels 768 (H) x 494(V) 752(H) x 582(V)
Sensor 1/3" High Resolution CCD
Scanning System 2:1 Interlace
Frequency
Horizontal :15.734KHzVertical : 59.94Hz
Horizontal :15.625KHzVertical : 50.00Hz
Resolution More than 630 TV Lines
Video Output 1.0Vp-p Composite Signal ( 75ohm )
AGC
S/N (Y signal)
Min.Illumination
White Balance
Electronic shutter speed 1/60s - 1/100,000s 1/50s - 1/100,000s
3D-DNR OFF / ON Selectable(LOW / MIDDLE / HIGH / CNR)
Sens-Up OFF / AUTO( x2 ~ x1024)
D&N Selection AUTO / COLOR / BW / EXT
BLC ON / OFF Selectable
D-WDR ON / OFF Selectable
HLM ON / OFF Selectable
Defect Pixel Compensation
IR SMART ON / OFF Selectable
Motion Detection OFF / ON(AREA 1~4)
Privacy Masking OFF / ON (MASK 1~8)
MIRROR ON / OFF Selectable
SHARPNESS ON / OFF (Level Adjustable 1~50)
Multi Language Available
O.S.D Available
IR LEDs 24IR LEDs
Lens Mount 3.6mm
Operating temperature/Humidity
-10℃~+50℃ / 0~80% RH
Power Supply DC12V 80mA (CDS ON 350mA)
Dimensions
Weight
112(W)mm X 87(D)mm
Appx. 200g
E
L
E
C
T
R
I
C
A
L
OFF / LOW / MIDDLE / HIGH
52dB or more (AGC OFF)
0 Lux for Infrared Lighting Conditions
ATW / AWC / MANUAL / PUSH
Built In OSD
SPECIFICATIONS
SETTING & INSTALLATION
When you install the camera,
please glue up the end of
cable to keep it stable in order
to protect the camera from
the humidity problems.
!
①
CONNECTOR ACCESSORIES
< DIMENSION >
Screws for Fixing
Base
Cover
Adjustable Angle
(Tilt : 10~90˚ / Manual)
Adjustable Angle
(Pan : 0~355˚ / Manual)
▶Screw for fixing
▶User's Manual
< FUNCTIONS >
▶ Video Test Output
▶ OSD Control
▶Video Test
Cable
1. Dome Base Mounting
- Open the dome cover ring from the dome base with coins.
- Mount the base of camera to a sturdy surface using screws with
accessories supplied through premade holes on the base
of the dome.
2. Power Connection & Monitor Impedance
- To avoid fire or shock hazard, always use a CE listed power supply.
- Check Monitor impedance switch if the image is blurred.
3. Camera Adjustment
- Adjust camera angel by moving the gymbal bracket.
- Adjust Zoom and Focus by lever attached to lens if it is varifocal lens.
- Use the OSD control to select the different ca mera functions if it is
OSD model.
4. Dome Cover Mounting
- Put the dome cover back and make sure it is properly fixed.
Loading...